Copper Meter Resetters

Transcription

1 Copper Meter Resetters To Set 5/8", 5/8" x 3/4", 3/4", 1", 1 1 2" & 2" Water Meters 11/12

2 Table of Contents Page Page Meter Resetters 5/8", 5/8" x 3/4", 3/4", & 1" Horizontal Inlet and Outlet Series 710 General Information...45 Series 717 Low Rise Style... 6 Series 718 Horizontal Style... 7 Series 719 Vertical Style Meter Thread x Meter Thread... 8 Series 768 Horizontal "F" Style Flexible... 9 Meter Resetters 1 1 2" & 2" Vertical Inlet and Outlet Series 718 No Bypass...12 With Bypass...13 Accessories Gaskets...14 Meter Bushings / Adapters...14 Meter Dimensions...14 Tandem Options...15 Sectional View...15 Series 758 Crab Style Tandem...10 Inverted Tandem...10 Inline Tandem...11 Page 45 Page Series 718 Series Page Series Page XDCA Series 717 with Backflow Preventer and Thermal Expansion Tank (Tank must be purchased separately) XDCC Series 717 used to retrofit existing high rise meter pit and standard meter resetter with backflow preventer and pressure relief valve FAX sales@aymcdonald.com aymcdonald.com 1112

3 General Information A.Y. McDonald Mfg. Co. Resetters offer a wide variety of options for resetting your current water meter to various heights and locations. Resetters are used where the meter is already installed and the service lines are in place, but the meter needs to be relocated above or next to the current line. A.Y. McDonald Mfg. Co. resetters provide you with an array of variations that will see you through any relocation project. Common resetter installations are shown below. You can customize your resetter solution on the pages within, or contact our factory professionals to help you through. Brass materials meet or exceed AWWA C800 (latest revision) Copper tubing has a 13 16" O.D. for 5/8", 5/8" x 3/4" or 3/4" meter resetters, 1 1 8" O.D. for 1" meter resetters, 1 5 8" for 1 1 2" meter resetters and 2 1 8" for 2" meter resetters. Solder is nolead. EPDM rubber gaskets are furnished as standard. Contact factory for fiber or leather gaskets. All meter resetters are factory tested air under water at 85 PSIG. Brass support bar is standard on 18" and higher meter resetters. Meter resetter heights over 24" available on special order. All meter swivel nuts have wire seal hole. Lockwing ball style meter valves are standard. Meter swivel nuts with meter support saddle are standard, except where noted. All copper meter resetters can be supplied with a test valve on the outlet tubing. For dual check backflow valves, see catalog section 13. Brace eye hole accepts 1/2" iron pipe or PVC for 5/8", 5/8" x 3/4" and 3/4" meters and 1" vertical meter resetters. Brace eye hole accepts 3/4" iron pipe or PVC for 1", horizontal meter resetters. Brace eye hole accepts 1" iron pipe or PVC for 1 1 2" & 2", horizontal meter resetters. BEFORE AFTER FAX sales@aymcdonald.com aymcdonald.com 3

4 710 SERIES The A.Y. McDonald Meter Resetter is a unique and patented product designed to easily retrofit existing meter installations to include a dual check backflow preventer, or pressure relief valve. This is accomplished without the high risk of cutting into old service lines, or the expensive process of digging up and replacing existing meter boxes or pits. This retrofitting can be easily performed in even the most confined meter boxes. Before NOTE: Meter box sold separately Meter Dimensions Meter Size 5/8" 5/8" x 3/4" 3/4" AMeter Threads 3/4" 1" 1" BLay Length 7 1 2" 7 1 2" 9" A.Y. M c Donald Spacing* " " " After NOTE: Meter box sold separately Available for 5/8", 5/8" x 3/4", or 3/4" meters Cast Brass Meter Nuts with Rubber Gaskets Copper Tubing Cast Brass Base Meter Threads Patent No. 4,691,727 Dual Check Backflow Preventer (optional) Meter Threads ASSE listed dual check Pressure Loss Data 5/8" Series 710 with backflow 5/8" Series 710 without backflow 20 5/8" x 3/4" Series 710 with backflow 5/8" x 3/4" Series 710 without backflow 30 3/4" Series 710 with backflow 3/4" Series 710 without backflow WATER FLOW (Gallons Per Minute) WATER FLOW (Gallons Per Minute) WATER FLOW (Gallons Per Minute) PRESSURE DROP (Pounds per Square Inch) PRESSURE DROP (Pounds per Square Inch) PRESSURE DROP (Pounds per Square Inch) Thermal Expansion Warning Creating a closed condition in a hot water system with the installation of a nonreturn barrier (such as a Check Valve or Backflow Preventer between the system piping and the public supply) can result in extreme pressure rises caused by thermal expansion and/or water hammer. This thermal expansion can damage piping, valves, and other components in the system. The installation of a pressure relief device or thermal expansion tank can avoid possible damages FAX sales@aymcdonald.com aymcdonald.com 1112

5 Offset Left Standard 710 SERIES Approx. 6 Approx. 3 Side View 710 Inlet Series Style Meter Size Meter Height Meter Connections Bottom Bar 1/2" FNPT Space Tube Offset Options Bottom Bar Tap 710 = Standard For crossed sized meter sets A = 5/8" B = 5/8" x 3/4" C = 3/4" R = Right offset A B Tap Locations Model NN 1 1 = 5/8" 2 = 5/8" x 3/4" 3 = 3/4" 06 3" 6" 7" 12" Resetters with crossover meter sizes are available, contact factory. * For angle ball valves integral to resetter, contact factory. Not all combinations available, contact factory with your requirements. Most Meter RESetters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements. * N N N = No valve (meter nut only without saddle) Q = Lockwing ball valve (without saddle) Side View 72 Left Offset Standard Inlet Model NN X72 = No option C = Dual check on inlet H = Dual check on outlet J = Adapter idler on outlet (sized to fit meter) U = UFR on outlet (Integral) A B Tap Locations X72 See above side view as required = No tap A = Tap inlet, no plug B = Tap outlet, no plug D = Tap outlet, with 125# PRV E = Tap inlet, with 175# PRV F = Tap outlet, with 175# PRV G = Tap inlet, with plug H = Tap outlet, with plug L = Tap inlet, with 125# PRV (Inlet is city side, outlet is house side) Ordering Options Separately Dual Check Backflow Preventer (Inlet side) 7113AN 34 For 5/8" meter 7113AN 44 For 5/8" x 3/4" and 3/4" meter Inlet: Male meter thread Outlet: Female meter thread (union) Dual Check Backflow Preventer (Outlet side) 7113NA 43 For 5/8" meter 7113NA 44 For 5/8" x 3/4" and 3/4" meter Inlet: Female meter thread (union) Outlet: Male meter thread Pressure Relief Valve 710P lb. rated 710P lb. rated 1/2" MNPT thread 710J11 Meter Adapter Idler (New Style) 3 3/4" long with gasket, adapts basic 710 Series unit (less backflow preventer) to 7 1 2" lay length 5/8" meter 710J22 Meter Adapter Idler 3 3/4" long with gasket, adapts basic 710 Series unit (less backflow preventer) to 7" lay length 5/8" x 3/4" meter 710J23 Meter Adapter Idler 1 1 2" long with gasket. Use with 710 Series unit and backflow preventer to increase lay length 3/4" meter Plug / FAX sales@aymcdonald.com aymcdonald.com 5

6 717 SERIES Low Rise Style Resetter 90º tubing to bottom bar is standard, contact factory for other options. The A.Y. McDonald 717 Series low rise resetter allows you to reset a meter incorporating an inlet or outlet shut off valve or check valve. It also offers several options for taps to incorporate pressure relief valves or sampling valves before or after the meter. Ninety degree tubing to bottom bar is standard, other options are available (contact factory for information). 90º Offset Right View Standard INLET Meter Thread OUTLET Meter Thread 717 Left Offset Inlet (city side) Series Style Meter Size Meter Height Meter Connections Bottom Bar FNPT Optional Offset Tap Location Bottom Bar Tap 717 = Standard For crossed sized meter sets A = 5/8" B = 5/8" x 3/4" C = 3/4" Tap A Offset Left: U = 5/8" V = 5/8" x 3/4" W = 3/4" X = Offset Left Tap D (bottom) Tap C (top) Tap B 2 1 = 5/8" 2 = 5/8"x 3/4" 3 = 3/4" 4 = 1" 04 4" 6" for 1" meter only. For special heights, contact factory. W D C = Angle single check valve on outlet D = Angle dual check valve on outlet (ASSE 1024) W = Angle lockwing ball valve X = No valve meter nut only For other special meter connections, contact factory. Outlet (house side) Model WD Right Offset Inlet (city side) Tap A Tap C (bottom) Tap B Tap D (top) Outlet (house side) = No Tap A = Inlet Left B = Outlet Left C = Outlet Top D = Outlet Bottom 45 = 45º 60 = 60º 180 = 180º = No tap A = 1/2" FNPT no plug B = 1/2" FNPT with brass square head plug C = 1/2" FNPT 125# PRV D = 3/4" FNPT no plug (only 1" resetter) E = 3/4" FNPT with brass square head plug (only 1" resetter) Series 717 is typically viewed from the inlet side, and is fabricated as a right offset (see photo above and at right). This is critical when considering tap locations. Left offset is available upon special request contact factory. Not all combinations available, contact factory with your requirements. Most Meter RESetters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements FAX sales@aymcdonald.com aymcdonald.com 1112

7 718 SERIES Horizontal Style Resetter Minimum 10" height on 1" resetters, or 12" on 1" resetter with angle dual check. The A.Y. McDonald 718 horizontal resetter allows you to reset a meter incorporating an inlet or outlet shut off valve or check valve while offering several height options. It also offers several options for taps to incorporate pressure relief valves or sampling valves before or after the meter. Depending on valve configurations, minimum heights may vary. INLET Meter Thread OUTLET Meter Thread 718 Series Style Meter Size Meter Height Meter Connections Bottom Bar FNPT Tap Location Bottom Bar Tap For Tandem Series 718 = Standard For crossed sized meter sets A = 5/8" B = 5/8" x 3/4" C = 3/4" 2 1 = 5/8" 2 = 5/8"x 3/4" 3 = 3/4" 4 = 1" Model WX 07 07" 09" 10" 12" 15" 18" 21" 24" For special heights, contact factory. W X Blank = No Tap A = 1/2" FNPT inlet B = 1/2" FNPT outlet C = Angle single check valve on outlet D = Angle dual check valve on outlet (ASSE 1024) W = Angle lockwing ball valve X = No valve meter nut only For other special meter connections, contact factory. Blank = No Tap A = 1/2" FNPT no plug B = 1/2" FNPT with brass square head plug C = 1/2" FNPT 125# PRV D = 1/2" FNPT 175# PRV 758 Series Horizontal Tandem Setter Example WX Tandem resetters are supplied with adapters and S tube. Please specify device length and threads when ordering. Not all combinations available, contact factory with your requirements. Most Meter RESetters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements FAX sales@aymcdonald.com aymcdonald.com 7

8 719 SERIES Vertical Style Resetter Meter Thread x Meter Thread The A.Y. McDonald 719 vertical to horizontal resetter allows you to reset a meter currently in a vertical position to a horizontal position incorporating an inlet or outlet shut off valve or check valve. It also offers several height options and several options for taps to incorporate pressure relief valves or sampling valves before or after the meter. Meter swivel nuts are less saddle 719 Model 7192 Series Style Meter Size Meter Height Meter Connections Bottom Bar FNPT Tap Location Bottom Bar Tap 718 = Standard For crossed sized meter sets A = 5/8" B = 5/8" x 3/4" C = 3/4" 2 1 = 5/8" 2 = 5/8" x 3/4" 3 = 3/4" 4 = 1" = Standard For special heights, contact factory. Q N Blank = No Tap A = 1/2" FNPT inlet B = 1/2" FNPT outlet A = Angle single check valve on outlet F = Angle dual check valve on outlet (ASSE 1024) Q = Angle lockwing ball valve N = No valve meter nut only For other special meter connections, contact factory. Blank = No Tap A = 1/2" FNPT no plug B = 1/2" FNPT with brass square head plug C = 1/2" FNPT 125# PRV D = 1/2" FNPT 175# PRV Not all combinations available, contact factory with your requirements. Most Meter RESetters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements FAX sales@aymcdonald.com aymcdonald.com 1112

9 768 SERIES Horizontal "F" Style Flexible Resetter Minimum 15" height on 1" resetters. Resetters with crossover meter sizes are available, contact factory. The A.Y. McDonald 768 horizontal F Style (Flexible) resetter allows you to reset a meter incorporating an inlet or outlet shut off valve or check valve. It also offers several height options and flexibility if existing set is not aligned correctly. INLET Meter Thread OUTLET Meter Thread Model WX W X Series Style Meter Size Meter Height Inlet Outlet Meter Connections 768 = Standard For crossed sized meter sets A = 5/8" B = 5/8" x 3/4" C = 3/4" 1 = 5/8" 12" 2 = 5/8" x 3/4" 15" 3 = 3/4" 18" 4 = 1" 21" 24" For special heights, contact factory. C = Angle single check valve on outlet (Not availabe on 1") D = Angle dual check valve on outlet (ASSE 1024) W = Angle lockwing ball valve X = No valve meter nut only For other special meter connections, contact factory. For Tandem Series 761 Series Horizontal Tandem Setter Example WX Tandem resetters are supplied with adapters and S tube. Please specify device length and threads when ordering. Not all combinations available, contact factory with your requirements. Most Meter RESetters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements FAX sales@aymcdonald.com aymcdonald.com 9

10 758 SERIES Crab Style Tandem Resetter Made to set two 7 1 2" meter thread x meter thread devices. The A.Y. McDonald 758 tandem resetter allows you to reset a meter and a device in one low profile compact setting. Meter swivel nuts are less saddle Model 7582NN X N N X419 Series Style Meter Size Meter Height Meter Connections Blank Space Crab Style 758 Tandem = Standard 2 = 5/8" x 3/4" 3 = 3/4" 4 = 1" For special heights, contact factory. N = No valve meter nut only For other special meter connections, contact factory. Inverted Tandem For installing a regulator and meter in an existing setting and there is little room above 2" rise from original meter height. The A.Y. McDonald 758 inverted tandem resetter allows you to reset a meter and a device with minimal rise as long as there is room below the existing meter. Meter swivel nuts are less saddle Model NN X X406 Series Style Meter Size Meter Height Meter Connections Blank Space Inverted Style N N 758 Tandem = Standard 1 = 5/8" 2 = 5/8" x 3/4" 3 = 3/4" For special heights, contact factory. N = No valve meter nut only For other special meter connections, contact factory. Meter swivel nuts are less saddle. Not all combinations available, contact factory with your requirements. Most Meter RESetters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements FAX sales@aymcdonald.com aymcdonald.com 1112

11 758 SERIES Inline Tandem Resetter The A.Y. McDonald 758 inline tandem resetter with additional options for shut off or check valves plumbed into the tubing to accept inline, a meter and a pressure regulating device. Please supply device length and end connection configuration when ordering. Resetters include meter coupling and adapter and gaskets. Meter swivel nuts are less saddle INLET Meter Thread OUTLET Meter Thread Model QN X Q N X15.81 Series Style Meter Size Meter Height Meter Connections Blank Space Flange to Flange Spread 758 = Standard 1 = 5/8" 2 = 5/8" x 3/4" 3 = 3/4" 4 = 1" 07" 09" 10" 12" 15" 18" 21" 24" For special heights, contact factory. A = Angle single check valve on outlet F = Angle dual check valve on outlet (ASSE 1024) Q = Angle lockwing ball valve N = No valve meter nut only For other special meter connections, contact factory. Not all combinations available, contact factory with your requirements. Most Meter RESetters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements FAX sales@aymcdonald.com aymcdonald.com 11

12 718 SERIES Horizontal Style Resetters 1 1 2" & 2" No Bypass 1" Copper cross tube is standard for no bypass setters. The A.Y. McDonald " and 2 oval flanged horizontal resetter allows you to reset a meter incorporating an inlet or outlet shut off valve or check valve while offering several height options. It also offers bypass options and several options for taps to incorporate pressure relief valves or sampling valves before or after the meter. Depending on valve configurations, minimum heights may vary. Brass eye holes accept 1" iron pipe or 1" PVC. INLET Meter Flange OUTLET Meter Flange For Tandem Series 718 Series Style Meter Size Meter Height Inlet Outlet Meter Connections 718 = Standard No Bypass 6 6 = 1 1 2" 7 = 2" Lower heights may be available contact factory. Model WD 18 15" 18" 21" 24" For special heights, contact factory. Minimum height may apply based on configuration of setter. W D D = Angle dual check valve E = Angle dual check valve with 1" tap in cap with 1" NPT plug assembly F = Angle dual check valve with 1 1 2" tap in cap with 1 1 2" NPT plug assembly G = Angle dual check valve with 2" tap in cap with 2" NPT plug assembly N = Flanged elbow T = Flanged tee with 2" plug in top of tee for access W = Angle lockwing ball valve 758 Series Tandem Setter Example WD Tandem resetters are supplied with 610M adapters and S tube. Please specify device length and threads when ordering. Not all combinations available, contact factory with your requirements. Most Meter RESetters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements FAX sales@aymcdonald.com aymcdonald.com 1112

13 INLET Meter Flange OUTLET Meter Flange 718 SERIES Horizontal Style Resetters 1 1 2" & 2" With Bypass The A.Y. McDonald " and 2" oval flanged horizontal resetter allows you to reset a meter incorporating an inlet or outlet shut off valve or check valve while offering several height options. It also offers bypass options and several options for taps to incorporate pressure relief valves or sampling valves before or after the meter. Depending on valve configurations, minimum heights may vary. Brass eye holes accept 1" iron pipe or 1" PVC 2" Meter flanges have slotted bolt holes to fit 1 1 2" or 2" meters Two drop in flange gaskets furnished. Two meter support brackets furnished. 1¼" bypass includes a 1" x 1" x 1 1 4" ball valve. Resetter with bypass requires a check valve or ball valve on outlet Cross sized resetters available, contact factory. 718 For Tandem Series B 6 Series Bypass Meter Size Meter Height Inlet Outlet Meter Connections = 1 1 2" 7 = 2" B = Low bypass R = High Offset Model 718B618WD 18 12" 15" 18" 21" 24" For special heights, contact factory. Minimum height may apply based on configuration of setter. W D D = Angle dual check valve E = Angle dual check valve with 1" tap in cap with 1" NPT plug assembly F = Angle dual check valve with 1 1 2" tap in cap with 1 1 2" NPT plug assembly G = Angle dual check valve with 2" tap in cap with 2" NPT plug assembly N = Flanged elbow T = Flanged tee with 2" plug in top of tee for access W = Angle lockwing ball valve 758 Series Tandem Setter Example WD Tandem resetters are supplied with 610M adapters and S tube. Please specify device length and threads when ordering. Setter Height B = Low Bypass 6.50 R = High Ofset Bypass Not all combinations available, contact factory with your requirements to right of meter Most Meter RESetters are Made to order and are not returnable. Please verify with the factory that the model number you have configured is available and meets your requirements FAX sales@aymcdonald.com aymcdonald.com 13

14 Gaskets METER MODEL DESCRIPTION SIZE 18G1 5/8" Rubber 5/8" 18G1F 5/8" Fiber 5/8" 18G1L 5/8" Waxed Leather 5/8" 18G2 3/4" Rubber 5/8" x 3/4" or 3/4" 18G2F 3/4" Fiber 5/8" x 3/4" or 3/4" 18G2L 3/4" Waxed Leather 5/8" x 3/4" or 3/4" 18G4 1" Rubber 1" 18G4F 1" Fiber 1" 18G4L 1" Waxed Leather 1" Two drop in flange gaskets furnished. Two meter support brackets furnished. METER MODEL DESCRIPTION SIZE 18G " FlangeRubber 1 1 2" 18G7 2" FlangeRubber 2" 4620G 1 1 2" RoundRubber 1 1 2" 4620G 2" RoundRubber 2" 2" Meter Flanges have slotted bolt holes to fit 1 1 2" or 2" meters. Meter Bushings Changes thread size only 10J12 Converts 5/8" meter spud to 5/8" x 3/4" meter spud two pieces required per meter 10J45 Converts 1" meter spud to 1 1 4" meter spud two pieces required per meter Meter Adapters Converts meter size and laying length 10J12KIT Converts 5/8" meter spud to 5/8" x 3/4" meter spud two pieces per bag 710J13 Converts 5/8" meter to 3/4" meter two pieces required per meter 710J46KIT Converts 1" meter to 1 1 2" flanged meter size and length two pieces per kit 710J13KIT Converts 5/8" meter to 3/4" meter two pieces per kit 710J47 Converts 1" meter to 2" flanged meter size and length two pieces required per meter 710J14 Converts 5/8" meter to 1" meter two pieces required per meter 710J47KIT Converts 1" meter to 2" flanged meter size and length two pieces per kit 710J14KIT Converts 5/8" meter to 1" meter two pieces per kit 710J23 710J24 Converts 5/8" x 3/4" meter to 3/4" meter one piece required per meter Converts 5/8" x 3/4" meter to 1" meter two pieces required per meter 710J24KIT Converts 5/8" x 3/4" meter to 1" meter two pieces per kit 710J34 Converts 3/4" meter to 1" meter two pieces required per meter 710J34KIT Converts 3/4" meter to 1" meter two pieces per kit 710J67 Converts 1 1 2" flanged meter to 2" flanged meter size and length two pieces required per meter two bolts included 710J67KIT Converts 1 1 2" flanged meter to 2" flanged meter size and length two pieces per kit four bolts included 710J67DH Converts 1 1 2" flanged meter to 2" flanged meter size and length two pieces required per meter Slotted holes for 1 1 2" or 2" meters does not include bolts and nuts 710J77DHX2 X1.75 Converts 2" x 15.25" flanged meter to 2" x 17" flanged meter size and length one piece required per meter. Slotted holes for 1 1 2" or 2" meters does not include bolts and nuts 710J46 Converts 1" meter to 1 1 2" flanged meter size and length two pieces required per meter 6121 Meter support bracket 1 1 2" and 2" Meter Dimensions Oval Flange Meter Size 5/8" 5/8" x 3/4" 3/4" 1" 1 1 2" 2" AMeter Threads 3/4" 1" 1" 1 1 4" 1 1 2" 2" BLay Length 7 1 2" 7 1 2" 9" " 13" 17" A.Y. M c Donald Spacing* " " " " 13.38" 17.38" *Allows for meter and two gaskets. Note: A.Y. McDonald uses the above standards for typical meter applications. If your application is special or in question, you should always measure the meter as shown above. Other meter lay lengths must be specified. An additional 3/8" is added to top spacing to allow for gaskets: Standard 2" top spacing = " FAX sales@aymcdonald.com aymcdonald.com 1112

15 Tandem Options All A.Y. M c Donald tandem copper setters are designed to provide the user with the option of placing an auxiliary device in addition to a water meter in a space as small as 18" in diameter (see Table I). The auxiliary device could be a pressure regulator, pressure relief valve, backflow preventer, etc. Table I shows typical lay lengths available for these devices. Other lengths can be provided. Contact our customer service department for details. Standard centerline spread for 5/8", 5/8" x 3/4", 3/4" meters is 7". 1" meter is 9". Tandem meter setter S bar (4619Ssize) and brass adapters (74619size) come as standard when ordering tandem resetters, but are also available separately (see below). Contact factory. Resetters with crossover meter sizes are available, contact factory. TABLE I Meter Size Device Minimum Length Recommended (FNPT x FNPT) Inside Pit Diameter 5/8" 4" to 5" 18" 5/8" x 3/4" 4" to 5" 18" 3/4" 4" to 5" 20" 1" 5" to 6" 21" Tandem "S" Bar 4619S 5/8" for use with 5/8" meter tandem 4619S 5/8" x 3/4" for use with 5/8" x 3/4" meter tandem 4619S 3/4" for use with 3/4" meter tandem Above items for use with 4"5" device 4619S 1 for use with 1" meter tandem Above item for use with 5"6" device "S" Bar Adapter Two pieces required per device /8" (5/8" meter x 3/4" NPT) /4" (5/8" x 3/4" or 3/4" meter x 3/4" NPT) " (1" meter x 1" NPT) 7" 9" Spread for 5/8", 5/8"x 3/4" and 3/4" Meters Spread for 1" Meters Note: Special length cross tubes and inverted tandem cross tubes are available, contact factory. Sectional View ASSE 1024 Angle Meter Valve Ball Style Angle Dual Poppet Check Valve Single Poppet Check Valve Double wall flange thickness Test Valve in Tubing Copper Tube Flange Meter Threads FAX sales@aymcdonald.com aymcdonald.com 15

16 A.Y. McDonald Mfg. Co. is a leading manufacturer of Waterworks Brass, Plumbing Valves, Pumps and Water Systems, and High Pressure Gas Valves and Meter Bars. The Company has distinguished itself with a proud tradition of quality and reliability since its founding in The mission of A.Y. McDonald Mfg. Co., in the words of our founder, is to make good products and sell them honestly. We, the stockholders and employees, accomplish this by extending the McDonald family culture through excellent customer service and by focusing on our customers needs. WARNING: It is unlawful in CALIFORNIA & VERMONT (effective 1/1/2010); MARYLAND (effective 1/1/2012); LOUISIANA (effective 1/1/2013) and the UNITED STATES OF AMERICA (effective 1/4/2014) to use any product in the installation or repair of any public water system or any plumbing in a facility or system that provides water for human consumption if the wetted surface area of the product has a weighted average lead content greater than 0.25%. This prohibition does not extend to service saddles used in California, Louisiana or under USA Public Law /12 More than a brand. We re a family. aymcdonald.com sales@aymcdonald.com