How To Wire An Extron Ip Link Device To A Cell Phone With A Sim Sim Sim Card (Ipl) For A Sim Card With A Power Adapter (Iphones) For An Extravoy) For Free (For A Simio)

Transcription

1 poly_5_6486_1.pkn Revision: 4/1/013 This document provides additional assistance with wiring your Extron IP Link enabled product to your device. Different components may require a different wiring scheme than those listed below. For complete operating instructions, refer to the user s manual for the specific Extron IP Link enabled product or the controlled device manufacturer supplied documentation. Device Specifications: Device Type: Audio Processor Manufacturer: Polycom Firmware Version: SoundStructure Studio Version: Model(s): SoundStructure C-Series OBAM Minimum Software and Firmware Requirements: IP Link Compiler IP Link Firmware GC Version Version History: Driver Version Date Notes 1 3/8/013 Initial version. Driver Notes: The Polycom Firmware must be for this driver to function as expected. Group Names are required for status. This driver must be loaded on an Extron product that has more than 1mb of usable memory. In order for this driver to work with the SoundStructure, it is necessary to configure the virtual names to match the driver within the SoundStructure Studio available for free from Polycom. The driver includes optimization to the features listed below: a. Dynamic Text b. Dialing Feedback c. Volume Page 1 of 8

2 poly_5_6486_1.pkn Revision: 4/1/013 Virtual Names should be labeled as below. Table 1 Input/Output Type Driver Name Virtual Name Group Name* Mics Mute/Fader/Step Input 1 3 Input 1 3 Mics Amplifiers Mute/Fader/Step Output 1 3 Output 1 3 Outputs Hook Phone_connect Hook Phone Out 1 Flash Phone_flash Hook Flash Phone Out 1 Redial Phone_redial Hook Redial Phone Out 1 Dialing Keypad Phone_dial Dial Keypad Phone Out 1 Phone Output Mute/Fader/Step Phone Transmit Phone Out 1 Phone Input Mute/Fader/Step Phone Receive Phone In 1 Auto Answer phone_auto_answer_en Auto Answer Phone In 1 Hook Phone_connect Hook Phone Out Flash Phone_flash Hook Flash Phone Out Redial Phone_redial Hook Redial Phone Out Dialing Keypad Phone_dial Dial Keypad Phone Out Phone Output Mute/Fader/Step Phone Transmit Phone Out Phone Input Mute/Fader/Step Phone Receive Phone In Auto Answer phone_auto_answer_en Auto Answer Phone In Hook Phone_connect Hook VoIP Out 1 Dialing Keypad Phone_dial Dial Keypad VoIP Out 1 Phone Output Mute/Fader/Step Phone Transmit VoIP Out 1 Phone Input Mute/Fader/Step Phone Receive VoIP In 1 Auto Answer phone_auto_answer_en Auto Answer VoIP In 1 Hook Phone_connect Hook VoIP Out Dialing Keypad Phone_dial Dial Keypad VoIP Out Phone Output Mute/Fader/Step Phone Transmit VoIP Out Phone Input Mute/Fader/Step Phone Receive VoIP In Auto Answer phone_auto_answer_en Auto Answer VoIP In *Group Names are necessary for group control and status. Each physical input and output must be configured with a virtual name. All Inputs should be labeled as above. o It is recommended to make a group named Mics and add all the Inputs into this group (created by default in Studio). All Amplifiers should be labeled as above. o It is recommended to make a group named Outputs and add all the Outputs into this group. Example: Presets 1 16 must be labeled as Preset x (where x is 1 16). Refer to SoundStructure Design manual for more information. Page of 8

3 poly_5_6486_1.pkn Revision: 4/1/013 Virtual Channel Names: Select the Channels branch under the SoundStructure System Select the Edit Channels button on the top of the page Channels in the system are in the Channels Defined box. Page 3 of 8

4 poly_5_6486_1.pkn Revision: 4/1/013 Group Names: Select the Channels branch under the SoundStructure System Select the Edit Groups button on the top of the page Groups in the system are defined in the Channel Groups box. Page 4 of 8

5 poly_5_6486_1.pkn Revision: 4/1/013 Dialing Configuration: The Keypad is configured to display the digits on the field located at the top of the page. When the desired number is entered, press the Call button and that will connect you with the number you entered. When in a call, the keypad will be used the same as the DTMF tone where each number press will get sent out immediately. The Delete button will delete the last number displayed on the touch panel and is configured with the press/repeat functionality. The Clear button will clear all numbers entered. The Label on the top of the page, Please enter a number and press Call, is configured in GUI Configurator with an ID of and with the Dynamic text parameter enabled. Page 5 of 8

6 poly_5_6486_1.pkn Revision: 4/1/013 Control Commands & States: Auto Answer On Off Toggle Call Type Analog VoIP Dynamic ID Dial Keypad 0-9 # *, Delete Clear Do Not Disturb Mode On Off Hook On Off Flash Redial Input 1-3 Fade (Discrete) Input 1-3 Fade (Step) Up Down Input Group Fade Mute All Inputs On Off Toggle Mute All Outputs On Off Toggle Mute Input 1 3 On Off Toggle Mute Output 1 3 On Off Toggle Output 1-3 Fade Level (Discrete) Output 1-3 Fade Level (Step) Up Down Output Group Fade Level Phone Receive Fader Phone Receive Fader (Step) Up Down Phone Transmit Fader Phone Transmit Fader (Step) Up Down Preset Recall 1-16 Receive Mute On Off Toggle Page 6 of 8

7 poly_5_6486_1.pkn Revision: 4/1/013 Transmit Mute On Off Toggle VoIP Dial Mode Number URL Status Available: Auto Answer On Off Call Type Analog URL Call Status Ringing Not In a Call Status Unavailable Call in Progress Connected Connection Status Connected Disconnected Do Not Disturb Mode On Off Hook On Off Input 1-3 Fader(Discrete) Mute Input 1 3 On Off Mute Output 1 3 On Off Phone Receive Fader Phone Transmit Fader Receive Mute On Off Transmit Mute On Off Phone Receive Fader VoIP Dial Mode Number URL Page 7 of 8

8 poly_5_6486_1.pkn Revision: 4/1/013 Network communication: When configuring the Ethernet driver, be sure device settings match that of the GC configuration. Port Type: Ethernet Logon Credentials No Supported: Default Port: 5774 Multi-Connection Yes Capable: Port Changeable: No Ethernet Driver Configuration Description: Please refer to user manual for settings the network communication parameters. Notes for the Device: Page 8 of 8