Gaugeable Tube Fittings and Adapter Fittings

www.swagelok.com Gaugeable Fittings and dapter Fittings vailable in tube sizes from / to 2 and 2 to 50 mm Consistent gaugeability upon initial installation asy to disconnect and retighten Wide variety of materials and configurations

Gaugeable Fittings and dapter Fittings 2 Features Live-loaded, two-ferrule design. asy to install. No torque is transmitted to tubing during installation. Swagelok gap inspection gauge ensures sufficient pull-up upon initial installation. Back ferrule Hinge point Tubing Nut Front ferrule Fitting body uring assembly of the advanced-geometry design (above), the front ferrule is driven into the fitting body and the tubing to create primary seals, while the back ferrule hinges inward to create a strong grip on the tubing. The back ferrule geometry allows for an improved engineering hinging-colleting action that translates axial motion into radial swaging action on the tube, yet operates with a low assembly torque requirement. Two-Ferrule, Mechanical Grip esign The two ferrules separate sealing and tube gripping functions; each ferrule is optimized for its function. The front ferrule creates a seal: against the fitting body on the tubing outside diameter. s the nut is turned, the back ferrule: axially advances the front ferrule radially applies an effective tube grip. dvanced-geometry, Hinging Colleting Back Ferrule esign This design is standard on all to and to 2 mm Swagelok stainless steel tube fittings to help installers make more consistent, leak-tight tube connections. In these sizes, a patented case hardening process and patented recessed and contoured geometry provide unique engineering to the Swagelok back ferrule. The hinging-colleting back ferrule design expands on the already robust performance of the traditional ferrule design and provides: excellent gas-tight sealing and tube-gripping action easily achieved proper installation consistent remakes excellent vibration fatigue resistance and tube support full compatibility with original Swagelok stainless steel tube fittings of identical sizes. For additional information, see the 3 Stainless Steel Swagelok Fittings with dvanced Geometry Back Ferrules technical report, MS 0.

3 Gaugeable Fittings and dapter Fittings Contents Features, 2 Straight Fittings Weld Connectors The Swagelok Fitting dvantage, Unions Union, 0 Socket, 20 Materials, 8 Reducing Union, Specifications, 8 Male Pipe, 2 O-Rings, 8 Cleaning and Packaging, 8 Bulkhead Union and Bulkhead Reducing Union, 2 Female Connectors NPT, lternative Fuels-Type pproval, 8 Metric Swagelok Fittings, 9 Pressure Ratings, 9 s and, 0 dditional Products For SF 2507 super duplex tube fittings, see the Swagelok Gaugeable SF 2507 Super uplex Fittings catalog, MS 0 74. For alloy 400 tube fittings, see the Swagelok Gaugeable lloy 400/R 405 Mechanically ttached Pipe and Fittings catalog, MS 02 332. For PF tube fittings, see the Swagelok PF Fittings catalog, MS 0 05. For medium- and highpressure tube fittings, see the Swagelok Medium- and High- Pressure Fittings, Tubing, Valves, and ccessories catalog, MS-02-472. Male Connectors NPT, 3 ISO/BSP Tapered (RT), 4 ISO/BSP Parallel (RS), 5 ISO/BSP Parallel (RP), Bulkhead NPT, 7 S/MS Straight (ST) and Long S/MS Straight (ST), 7 O-Seal (S/MS Straight and NPT), 8 N and N Bulkhead Fitting, 9 0-32, M5 0.8, and Metric (RS), 20 Reducers Port Connectors ISO/BSP Tapered (RT), ISO/BSP Parallel (RJ and RP), 23 ISO/BSP Parallel (RG, Gauge), 24 Bulkhead NPT, 24 Reducer, 25 Long Reducer, 2 Bulkhead Reducer, 2 Port Connector and Reducing Port Connector,

4 Gaugeable Fittings and dapter Fittings Contents Caps and Plugs 45 lbows Female Cap, 28 Male NPT, 34 Run, NPT (TFT), 39 Plug, 28 Vent Protectors Positionable, S/MS Straight (ST), 34 Branch, NPT (TTF), 40 Mud auber, 28 Tees Cross 90 lbows Unions Unions Union and Reducing Union, 35 Union, 40 Union, 29 Sanitary Flange Fittings Male NPT, 30 Male Branch, NPT (TTM), 37 Kwik-Clamp Flange to Swagelok Fitting, 4 ISO/BSP Tapered (RT), 3 Run, NPT (TMT), 37 dapters dapter Information, 42 Weld Reducing, 3 Positionable, ISO/BSP Parallel (PR) and Positionable, S/MS Straight (ST), 32 Socket, 33 Male Pipe, 33 Positionable Branch, S/MS Straight (TTS) and Positionable Branch, ISO/BSP Parallel (TTR), 38 Positionable Run, S/MS Straight (TST), 38 Positionable Run, ISO/BSP Parallel (TRT), 39 Male NPT and ISO/BSP Tapered (RT), 43 ISO/BSP Parallel (RS and RP), 44 S/MS Straight (ST) and O-Seal (S/MS Straight ), 45 N, 45 Female Pipe Weld, 4 NPT, 33

Contents Gaugeable Fittings and dapter Fittings 5 Female NPT and ISO/BSP Tapered (RT), 4 ISO/BSP Parallel (RP and RJ), and ISO/BSP Parallel (RG, Gauge), 47 N, 47 dditional Information, 48 Replacement Parts Nuts ISO/BSP Parallel Gaskets O-Rings Steel (RS Fitting), Copper (RP Fitting), Copper (RG, Gauge Fitting), and PTF (RJ Fitting), 53 Buna N (O-Seal Straight s and O-Seal Pipe s) and Fluorocarbon FKM (ISO/BSP Parallel s and S/MS Straight s), 54 Tools and ccessories Hydraulic Swaging Units, 55 For tube benders, tube preparation tools, and tube support systems, see the Swagelok Tubing Tools and ccessories catalog, MS-0-79. Gaugeability, Installation Instructions, Bored-Through Fittings For thermocouples, dip tubes, and heat exchanger tees, Chromatograph Fittings See the Swagelok Gaugeable Chromatograph and Column nd Fittings catalog, MS-02-73. Female, 50 ielectric Fittings See the Swagelok ielectric Fittings catalog, MS 02 3 SCS. Knurled Female, 50 Preswaging Tools, 57 Flanges Ferrules Male, 50 Front, 5 Back, 5 Nut-Ferrule Set and Package and Ferrule Set and Ferrule-Pak Package, 52 Wrenches, 58 Gap Inspection Gauges and epth Marking Tools, 59 Bulkhead Retainers, 0 Inserts for Soft Plastic Tubing, 0 For liquid leak detectors, lubricants, and sealants, see the Swagelok Leak etectors, Lubricants, and Sealants catalog, MS 0 9. VCO and VCR Face Seal Fittings For NSI, IN, and JIS flanges, see the Swagelok Flange dapters catalog, MS-02-200. See the Swagelok VCR Metal Gasket Face Seal Fittings and VCO O-Rings Face Seal Fittings catalogs, MS 0 24 and MS 0 28.

Gaugeable Fittings and dapter Fittings The Swagelok Fitting dvantage Over 0 000 fittings and not a single leak. That is the message one customer wanted to share, crediting Swagelok components and tube fittings along with Swagelok distributor support, as having played a major role in completing and obtaining independent, third-party certification for two 2 000 ton oil rigs. nd that is part of the ongoing story behind the continuous improvement efforts that Swagelok has initiated and sustained since the development and patent of the original two-ferrule tube fitting more than 50 years ago. Today, as everyone is being called on to do more with less and to recognize value, Swagelok continues to improve the leak-tight design of the tube fitting for use in thousands of diverse applications including research, analytical and process instrumentation, bioprocessing, oil and gas, power, petrochemical, and semiconductor industries and addressing such critical issues as: leakage vibration (tube grip) thermal shock compliance with industry standards installation corrosion intermix/interchange. Leakage xcellent gas-tight sealing and consistent reassembly help ensure accurate measurements of process parameters air, steam, fuel, and water to keep your plant operating efficiently. Moreover, Swagelok tube fittings minimize fugitive emissions, as well as process fluid leakage and operation costs. From 999 through 2004, more than 250 000 fittings in gas service at more than 400 different process installations were leak tested with Swagelok Snoop liquid leak detector. Contact your authorized Swagelok sales and service representative for more information about Swagelok nergy missions Surveys or to schedule a survey. Vibration ( Grip) The patented case-hardening process and back-ferrule geometry provide excellent vibration fatigue resistance and tube support even in harsh or stressful environments, such as fuel processing or rotary equipment applications. Swagelok has conducted rotary flex tests, which show that the Swagelok tube fitting with advanced geometry hinging-colleting back ferrule isolates and protects the stress riser that is generated along the tube during the gripping part of assembly. The colleting portion of the back ferrule allows more material to contact the tube, for additional support. This colleting action enhances gripping performance and provides both direct and axial support to the gripping function. This design minimizes the effects of bending deflection at the point of grip on the tubing. Contact your authorized Swagelok representative for more information about vibration test reports.

Gaugeable Fittings and dapter Fittings 7 Thermal Shock The elastic, live-loaded two-ferrule design compensates for changes in temperature during system start-up and shutdown and helps eliminate leakage related to rapid thermal expansion or contraction. Swagelok has conducted tests that demonstrated the capability of Swagelok tube fittings to withstand thermal shock and high temperature. Contact your authorized Swagelok representative for more information about thermal shock test reports. Compliance with Industry Standards Swagelok Company works with standards organizations around the world to provide you with products that address your needs. See Materials, page 8; Specifications, page 8; and Pressure Ratings, page 9, for more information about the specifications to which Swagelok tube fittings are manufactured. Contact your authorized Swagelok representative for more information about Swagelok tube fitting certifications. Installation The Swagelok tube fitting installation advantages: asy to install No torque is transmitted to tubing during installation Swagelok gap inspection gauge assures sufficient pull-up upon initial installation. Swagelok tube fitting components provide exceptional dimensional, metallurgical, and mechanical uniformity that allow predictable, repeatable installation. Swagelok authorized sales and service centers offer installation training seminars that provide additional information on: The requirements for making safe, leak-tight connections variety of tools and accessories designed for use with Swagelok tube fittings. Corrosion Swagelok tube fittings are available in a variety of materials, including controlled-chemistry 3 stainless steel and many other alloys for enhanced corrosion resistance in a variety of applications, including sour gas and subsea systems. Swagelok has conducted tests in accordance with STM B7-95 to evaluate the corrosion resistance of Swagelok tube fittings. Contact your authorized Swagelok representative for more information about corrosion resistance test reports. Intermix/Interchange This practice can be dangerous. Leak-tight seals that will withstand high pressure, vibration, vacuum, and temperature changes depend on close tolerances and consistent, exacting quality control in conjunction with good design principles. The critical interaction of precision parts is essential for reliability and safety. Components of other manufacturers may look like Swagelok tube fitting components but they cannot be manufactured in accordance with Swagelok engineering standards, nor do they benefit from innovations in design and manufacture defined by 3 active Swagelok tube fitting patents issued since 989.

8 Gaugeable Fittings and dapter Fittings Materials Materials Standards Material Bar Stock➀ Forgings➁ 3 stainless steel STM, SM S479, N.440 STM 82, SM S82, N.440 lloy 20 STM B473 STM B42 lloy 400 STM B4 STM B54, SM SB54 lloy 00 STM B, SM SB STM B54, SM SB54 lloy 25 STM B44➂ STM B54, SM SB54➃ lloy 825 STM B425 STM B54, SM SB54 lloy C- STM B574 STM B54 luminum STM B2 STM B247 Brass STM B, STM B453 STM B283 Carbon steel STM 08 Nylon STM 40 PF➄ STM 3307 Type I PTF STM 70 STM 3294 SF 2507➅ STM 479 STM 82 Titanium (grade 4) STM B348 STM B38 ➀ Straight fittings and tube adapters. ➁ lbows, crosses, and tees. ➂ ll straight fittings and tube adapters and and ; and 0 mm elbows, crosses, and tees. ➃ lbows, crosses, and tees larger than and 0 mm. ➄ See the Swagelok PF Fittings catalog, MS-0-05. ➅ See the Swagelok Gaugeable SF 2507 Super uplex Fittings catalog, MS-0-74. dditional Processing Fitting bodies are processed for improved performance, as listed below. No additional processing is required for alloy 25, alloy 825, brass, nylon, 3 stainless steel, and PTF materials. Fitting Body Material luminum lloy 400, alloy 20, alloy C-, alloy 00 Carbon steel (except weld bodies) Carbon steel (weld bodies) Titanium Process nodized, hydrocarbon film Hydrocarbon film Zinc plating Hydrocarbon film chemical conversion coating nodized Over /25 mm fittings are supplied with a package of fluorinated-base with PTF and tungsten disulfide lubricant for use in fitting assembly. Over /25 mm stainless steel fittings use stainless steel ferrules with PF coating. pplications above 450 F (232 C) require silver-plated front ferrules and uncoated back ferrules. To order fittings with silver-plated front ferrules and uncoated back ferrules, add -BM to the fitting ordering number. xample: SS-2400--BM ll carbon steel Swagelok tube fittings are supplied with 3 stainless steel back ferrules. Specifications Type (nd Connection) NPT ISO/BSP (parallel) (Based on IN 3852) (Swagelok PR, RP, and RS fittings) ISO/BSP (tapered) (Based on IN 3852) (Swagelok RT fittings) ISO/BSP (gauge) (Based on N 837- and 837-3) (Swagelok RG and RJ fittings) Unified (S) (Swagelok ST fittings) Pipe Sealants thread sealant should always be used when assembling tapered threads. SWK anaerobic pipe thread sealant and Swagelok PTF tape are available. For more information, see the Swagelok Leak etectors, Lubricants, and Sealants catalog, MS-0-9. O-Rings O-seal fittings include a 70 durometer Buna N O-ring. Other straight-thread fittings with O-rings include a 90 durometer fluorocarbon FKM O-ring. Other O-ring materials are available upon request. O-rings are coated with a thin film of silicone-based lubricant. Removal of factory-applied lubricants may alter performance. Cleaning and Packaging Reference Specification SM B.20., S S705 ISO 8, JIS B0202 ISO 7, BS N 0-, JIS B0203 ISO 8, JIS B0202 SM B. Fitting components are cleaned to remove machine oil, grease, and loose particles. For more information, see Swagelok Standard Cleaning and Packaging (SC-0), MS 0 2. Fittings are available individually bagged; add CP to the ordering number. xample: SS-200-CP On request, fittings can be cleaned and packaged in accordance with Swagelok Special Cleaning and Packaging (SC-), MS 0 3, with front ferrules silver plated and Krytox 240 C applied to the internal surface of the nut. To order, add BQ to the ordering number. xample: SS-400--4BQ Oxygen Service Hazards For more information about hazards and risks of oxygenenriched systems, see the Swagelok Oxygen System Safety technical report, MS 0 3. lternative Fuels-Type pproval Stainless steel Swagelok Wall Thickness tube fittings used with 3 to mm 0.7 to 2.5 mm 3 stainless steel and 3 Ti stainless steel alloy tubing to 0.028 to 0.095 as shown in the table have been tested to the requirements of C R0, IHP raft, and C R7.

Gaugeable Fittings and dapter Fittings 9 Metric Swagelok Fittings Metric tube fittings have a stepped shoulder on the body hex. Shaped fittings, such as elbows, crosses, and tees, are stamped MM for metric tubing and have no step on the forging. Swagelok metric tube end Swagelok fractional tube stub Swagelok metric tube ends Stepped identification shoulders No shoulder Stepped identification shoulders Pressure Ratings Swagelok Fitting Pressure Ratings Swagelok tube fitting ends are rated to the working pressure of tubing as listed in Swagelok Tubing ata, MS-0-07. Careful selection of high-quality tubing is important when installing safe, leak-tight systems. Pipe nd (NPT and ISO 7) Pressure Ratings Basis Pressure ratings for fittings with both tube fitting and pipe thread ends are determined by the end connection with the lower pressure rating. The table lists pressure ratings for male and female tapered pipe thread ends. For female and male pipe threads to have the same pressure rating in the same nominal pipe size, the female thread would require a heavier wall, resulting in a fitting too large and bulky to be practical. llowable Stress Stress values are based on SM Code for Pressure Piping B3.3, Process Piping, at ambient temperature. llowable Stress Material psi bar 3 SS 20 000 378 Brass 0 000 89 Steel 20 000 378 Pressure Ratings Ratings are based on SM Code for Pressure Piping B3.3, Process Piping, at ambient temperature. NPT/ ISO 3 SS and Carbon Steel Brass Pipe Male Female Male Female psig bar psig bar psig bar psig bar / 000 757 700 4 5500 378 3300 7 0 000 89 500 447 5000 344 3200 0 8 000 55 00 454 4000 5 3300 7 7 800 537 5300 35 3900 28 200 79 7 700 530 4900 337 3800 2 2400 5 7 300 502 400 3 300 248 2300 58 5 300 35 4400 303 200 79 00 5 000 43 5000 344 3000 20 2500 72 5 000 344 400 3 2500 72 2300 58 2 3 900 28 3900 28 900 30 900 30 To determine pressure ratings in accordance with SM B3., Power Piping: carbon steel material multiply by 0.85. Stainless steel and brass material ratings remain the same. To determine MPa, multiply bar by 0.0. S/MS Fittings Pressure Ratings Basis Pressure ratings are based on S J92/3 at ambient temperature. 3 SS and Carbon Steel S/MS Nonpositionable Positionable esignator psig bar psig bar 5/-24 2ST 7/-20 4ST 458 34-20 5ST 458 34 9/-8 ST - 8ST 32 249-4 0ST /-2 2ST 32 249 2900 99 3/-2 4ST 5/-2 ST 2900 99 2320 59-2 20ST -2 24ST 2320 59 83 24 2-2 32ST 83 24 450 99 Male N (JIC) Fittings Pressure Ratings Pressure ratings are at ambient temperature. 3 SS Male N (JIC) Straight Shape esignator psig bar psig bar 7/-20 4N 0 000 89 0 000 89 9/-8 N - 8N 8 200 54 7 00 523 /-2 2N 7 000 482 300 434 5/-2 N 5 000 344 4 00 282 O-Seal Pressure Ratings Stainless steel and carbon steel O-seal fittings up to and 25 mm are rated to 3000 psig (20 bar). Positionable, ISO/BSP Parallel (PR) Pressure Ratings Pressure ratings are at ambient temperature. ISO/BSP Male Pipe 3 SS and Carbon Steel psig bar,, 458 34,, 2320 59

0 Gaugeable Fittings and dapter Fittings s and See How to Order, below. Minimum order quantities may apply to certain materials and configurations. are for reference only and are subject to change. Unless noted otherwise, dimensions shown are for stainless steel components and with Swagelok nuts finger-tight. For Swagelok nut dimensions, see page 50. C templates are available on www.swagelok.com. Straight Fittings Unions Tx T x Union, / -00-0.99 0.34 0.05-200-.40 0.50 0.09 3/ -300-.47 0.54 0.2-400-. 0.0 0.9 5/ -500-.9 0.4 0.25-00-.77 0. -80-2.02 0.90 0.4-80--0030➀ 4.30 0.50-00- 2.05 0.9-20- 2. 0.2-40- 2.7.02 0.72-0- 0.88 2.55.23-80- 0.97-2000- 3.3.2.09-2400- 4.25.97.34 2-3200- 5.88 2..8, mm 2-2M0-35. 3-3M0-35.3 2.9 4-4M0-37.3 3.7.7 2.4 -M0-4.0 5.3 8-8M0-43.2.2.4 0-0M0-4.2 7.2 2-2M0-5.2.8 4-4M0-. 5-5M0-52.0.9 24.4 -M0-2.7 8-8M0-53.5 5. 20-20M0-5.9 55.0 2.0 -M0-8.3 25-25M0-5.0 3.3 28-28M0-85.0 3. 2.8 B-28M0-5.4 3. 24. 30-30M0-92.7 39. 2.2 32-32M0-97.3 42.0 28. 38-38M0-4 49.4 33.7 50-50M0-4 5.0 45.2 ➀ Bored through. Union (Metric to Fractional) T Tx, x F, mm 2-2M0--2-2M0--4 35.2 38. 2.9 2.8 5.3 3-3M0--2 35.2 2.9 2.8 2.4 2 4-4M0--2 3.5 2.8 2 3.7 2.4-4M0--4 39.4 5.3 4 / 5/ -M0-- -M0--2 -M0--4 -M0--5 -M0-- 34.3 38.5 4.0 42.3 43.2 5.3 8. 2.8 5.3.2.8.3 2.4 4 4 4 4 8 0 2 5/ 5/ -8M0--4-8M0-- -0M0--2-0M0--4-0M0--5-0M0-- -2M0--4-2M0--5-2M0-- -2M0--8 42.3 44.3 44.5 45. 45.9 47.0 47.8 48.4 5.2.2 7.2.8 5.3.9 2.8 5.3.2.9 5.3.2.9.8.7.4 2.4.4 7..4 7. 5-5M0--8 52.0 24.4.8 0.3 24 -M0--0 52.0 24.4 24.4 2.7 24 8-8M0--2 53.5 24.4 24.4 5. 20-20M0--8-20M0-- 55.0 2.8 2.0.8 3.3 0.3 5.9 25-25M0-- 5.0 3.3 3.3 2.8 35 How to Order Select a basic ordering number. xample -00- dd a material designator. xample: SS-00- Material esignator Material esignator 3 SS SS lloy C- HC luminum Brass B lloy 20 C20 Carbon steel S lloy 400 M Nylon NY lloy 00 INC PTF T lloy 25 25 Titanium lloy 825 825 (grade 4) TI 2 4 5 8 30 35

Straight Fittings Unions Reducing Union Gaugeable Fittings and dapter Fittings T x Tx T Tx x, / -200--. 0.50 0.34 0.05 3/ 5/ / / 3/ / 5/ -300-- -300--2-400-- -400--2-400--3-500--2-500--4-00-- -00--2-00--4-00--5-80--2-80--4-80-- -00-- -00--8-20--4-20-- -20--8-20--0-0--8-0--2..44.35.52.55.5..44..70.74.78.85.9.94 2.05.94 2.00 2. 2. 0.54 0.0 0.4 0. 0.90 0.9 0.9 2.38.23 0.34 0.50 0.34 0.50 0.54 0.50 0.0 0.34 0.50 0.0 0.4 0.50 0.0 0. 0. 0.90 0.0 0. 0.90 0.9 0.90 0.9 0.05 0.09 0.05 0.09 0.2 0.09 0.9 0.05 0.09 0.9 0.25 0.09 0.9 0.4 0.9 0.4 0.50 0.4 0.2, mm 3 2-3M0--2M 35.3 2.9 2.9.7 0 2 2 3 4 -M0--2M -M0--3M -M0--4M 38. 38. 39.4 5.3 2.9 2.9 3.7.7 2.4 2.4 8-8M0--M 42.3.2 5.3 8 8 0 0 2-0M0--M -0M0--8M -2M0--M -2M0--8M -2M0--0M -M0--0M -M0--2M 44.5 45. 47.0 47.8 48.7 4 52.0 7.2.8 24.4 5.3.2 5.3.2 7.2 7.2.8.4.4 8 2-8M0--2M 53.5 24.4.8 25 30 32 38 8 20 8 20 25 8 20 25 20 25 30-25M0--8M -25M0--20M -30M0--8M -30M0--20M -30M0--25M -32M0--8M -32M0--20M -32M0--25M -38M0--20M -38M0--25M -38M0--30M.0 2.3 75.4 75.4 80. 77.8 77.8 82.3 87.5 92.0 05 3.3 39. 42.0 49.4 24.4 2.0 24.4 2.0 3.3 24.4 2.0 3.3 2.0 3.3 39. 5. 5.9 5. 5.9 2.8 5. 5.9 2.8 5.9 2.8 2.2

2 Gaugeable Fittings and dapter Fittings Straight Fittings Unions Bulkhead Union ➀ Minimum panel thickness is 0.0 F Panel Hole Max Panel Thickness, / -00-.24 0.34 0.05 5/ 3/4 0.2➀ -200-2.02 0.50 0.09 2/4 3/ -300-2. 0.54 0.2 9/ 25/4 0.50-400- 2. 0.0 0.9 29/4 0.40 5/ -500-2.39 0.4 0.25 / 33/4-00- 2.45 0. 37/4-80- 2.80 0.90 0.4 5/ 49/4-00- 2.8 0.9 0.50 / 57/4 0.44 0.50-20- 3. 0.9 0.2 3/ /4 0. -0-3.77.23 0.88 2/4-2000- 5.2.09 4/4-2400- 5.48.97.34 2 /4 2-3200- 7.0 2..8 2 2 4/4, mm 3-3M0-5.3 2.9 2.4 8.3 4 4-4M0-53. 3.7 2.4 9.9 0.75 2.7 -M0-57.7 5.3.5 0.2 8-8M0-.0.2.4 8 3. 0-0M0-3.7 7.2.3 2-2M0-7.0.8 24 4-4M0-72.5 24.4. 5-5M0-72.5 24.4.9 -M0-72.5 24.4 2.7.5.8.2 2.7 8-8M0-78.9 24.4 5. 30 2.0.8 20-20M0-84.5 2.0 5.9 35 29.0 25-25M0-9.0 3.3 2.8 4 34.0 30-30M0-24 39. 2.2 40.5 50 32-32M0-28 42.0 28. 42.5 38-38M0-45 49.4 33.7 0 50.5 Bulkhead Reducing Union 9.0 T x Tx T Tx x F, Panel Hole Max Panel Thickness / -200--.85 0.50 0.34 0.05 2/4 0.50-400--2 2.7 0.0 0.50 0.09 29/4 0.40-00--4 2.39 0. 37/4 0.44 0.0 0.9-80--4 2.3 0.90 5/ 49/4 0.50 Bulkhead Reducing Union (Metric to Fractional) T Tx, x F, mm Panel Hole Max Panel Thickness -M0--2 55. 5.3 2.7 2.4.5 0.2

Gaugeable Fittings and dapter Fittings 3 Straight Fittings Male Connectors NPT / 3/ 5/ NPT / / / ➀ F, -00-- -00--2-00--4-200-- -200--2-200--4-200-- -200--8-300--2-300--4-400-- -400--2-400--4-400-- -400--8-400--2-500--2-500--4-500-- -00--2-00--4-00-- -00--8-00--2-00-- -80--2-80--4-80-- -80--8-80--2-80-- -00--4-00-- -00--8-00--2-20-- -20--8-20--2-20-- -40--8-40--2-40-- -0--8-0--2-0-- 0.94.03..7.20.40.4..23.43.29.29.49.5.7.82.34.52.54.39.57.57.82.88 2.4.53.7.7.93.99 2.25.74.74.93.99.80.99.99 2.25.99.99 2.25 2.2 2.2 2.45 0.34 0.05 0.50 0.09 0.54 0.2 0.0 0.4 0. 0.90 0.9 0.9.02.23 0.2 0.9 0.9 0.9 0.9 0.9 0.9 0.25 0.25 0.9 0.9 0.38 0.4 0.4 0.4 0.38 0.47 0.50 0.4 0.47 0.2 0.2 0.47 0.2 0.72 0.47 0.2 0.88 5/ 7/ 9/ 7/ 7/ 9/ / 7/ 9/ 9/ / / 9/ 9/ / / / 3/ 3/ 3/ / 5/ 5/ 5/ / / / / 3/ 3/ -80-- 2.45.23 0.88-2000-- -2000--20 3.04.2 0.88.09-2400--24 3.50.97.34 2 2 2-3200--32 4.47 2..8 2 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. NPT ➀ F, mm 2-2M0--2 30.5 2.9.7 2 3 4 8 0 2 4-3M0--2-3M0--4-4M0--2-4M0--4 -M0--2 -M0--4 -M0-- -M0--8-8M0--2-8M0--4-8M0-- -8M0--8-0M0--2-0M0--4-0M0-- -0M0--8-0M0--2-2M0--2-2M0--4-2M0-- -2M0--8-2M0--2-4M0--4-4M0-- -4M0--8 30.5 35. 3.2 3.3 32.8 3 38.4 44.7 34.2 38.7 39.3 45. 3.3 40.9 40.9 4.5 48.0 38.8 43.4 43.4 49.0 50.5 44. 44. 49.0 2.9 2.4 3.7 2.4 5.3.2 7.2.8 24.4.4.4.4 7. 7. 7.. 2 4 2 4 4 4 8 5 5 8 8 8 8 5-5M0--8 49.0 24.4.9 24 8 20 25 28 -M0-- -M0--8 -M0--2-8M0--8-8M0--2-20M0--8-20M0--2 -M0--2 -M0-- -25M0--8-25M0--2-25M0-- -28M0-- -28M0--20 B-28M0-- B-28M0--20 44. 49.0 50.5 24.4 50.5 24.4 52.3 2.0 52.3 57. 57.5 57.5 2.3 72.4 73. 75.0 77.3 2.0 3.3.9 2.7.9 5..9 5.9 5.9 8.3.9 5.9 2.8 3. 2.8 3. 24. 30-30M0--20 77.2 39. 2.2 4 32-32M0--20 79. 42.0 28. 4 38-38M0--24 9. 49.4 33.7 55 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. 24 24 24 30 30 35 35 4 4 4 4

4 Gaugeable Fittings and dapter Fittings Straight Fittings Male Connectors See page 8 for thread specifications. ISO/BSP Tapered (RT) 5/ ISO ➀ F, -200--2RT -200--4RT -400--2RT -400--4RT -400--RT -400--8RT -500--2RT -500--4RT -00--2RT -00--4RT -00--RT -00--8RT -00--2RT -80--4RT -80--RT -80--8RT -80--2RT.20.40.29.49.5.7.34.52.39.57.57.82.88.7.7.93.99 0.50 0.09 0.0 0.9 0.4 0. 0.90 0.9 0.25 0.9 0.38 0.4 0.4 7/ 9/ 9/ / 9/ / / 3/ 3/ / -00--8RT.93 0.9 0.47 5/ -20--2RT -20--RT -0--2RT -0--RT.99 2.25 2.2 2.45 0.9 0.2.23 0.3 0.88 / -2000--20RT 3.04.2.09 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. ISO, ➀ F, mm 2-2M0--2RT 30.5 2.9.7 2 3 4 8 0 2 4-3M0--2RT -3M0--4RT -4M0--2RT -4M0--4RT -M0--2RT -M0--4RT -M0--RT -M0--8RT -8M0--2RT -8M0--4RT -8M0--RT -8M0--8RT -0M0--2RT -0M0--4RT -0M0--RT -0M0--8RT -0M0--2RT -2M0--4RT -2M0--RT -2M0--8RT -2M0--2RT -4M0--4RT -4M0--RT 30.5 35. 3.2 3.3 32.8 3 38.4 44.7 34.2 38.7 39.2 45. 3.3 40.9 40.9 4.5 48.0 43.4 43.4 49.0 50.5 44. 44. 2.9 2.4 3.7 2.4 5.3.2 7.2.8 24.4.4.4.4 7. 7. 7. 2 4 2 4 4 4 8 5 5 8 8 8 8 5-5M0--8RT 49.0 24.4.9 24 8 20 25 28 -M0--4RT -M0--RT -M0--8RT -M0--2RT -8M0--8RT -8M0--2RT -20M0--8RT -20M0--2RT -M0--2RT -M0--RT -25M0--8RT -25M0--2RT -25M0--RT -28M0--RT -28M0--20RT B-28M0--RT B-28M0--20RT 44. 44. 49.0 50.5 24.4 50.5 24.4 52.3 2.0 52.3 57. 57.5 57.5 2.3 72.4 73. 75.0 77.3 2.0 3.3 7..9 2.7.9 5..9 5.9 5.9 8.3.9 5.9 2.8 3. 2.8 3..2 30-30M0--20RT 77.2 39. 2.2 4 32-32M0--20RT 79. 42.0 28. 4 38-38M0--24RT 9. 49.4 33.7 55 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. 24 24 24 24 30 30 35 35 4 4 4 4

Gaugeable Fittings and dapter Fittings 5 Straight Fittings Male Connectors See page 8 for thread specifications. ISO/BSP parallel gaskets are available. See page 53. ISO/BSP Parallel (RS) ISO ➀ F, -200--2RS -200--4RS -200--RS -400--2RS -400--4RS -400--RS -400--8RS -00--2RS -00--4RS -00--RS -00--8RS -80--4RS -80--RS -80--8RS -20--8RS -20--2RS -0--8RS -0--2RS -0--RS.3.50.53.40.59.2.70.49.5.8.7.7.79.87.92 2.05 2.9 2. 2.35 0.50 0.09 0.0 0. 0.90 0.9.23 0. 0.9 0.9 0.9 0. 0.23 0.23 0.3 0.4 0.47 0.2 0.47 0.3 0.78 9/ 9/ / / 3/ / / 5/ ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. ISO, ➀ F, mm 2-2M0--2RS 33.3 2.9.7 4 3-3M0--2RS -3M0--4RS 33.3 38. 2.9 2.4 4-4M0--2RS 34.0 3.7 2.4 4 8 0 2 4 5 8 20 25 28 -M0--2RS -M0--4RS -M0--RS -M0--8RS -8M0--2RS -8M0--4RS -8M0--RS -8M0--8RS -0M0--4RS -0M0--RS -0M0--8RS -2M0--4RS -2M0--RS -2M0--8RS -2M0--2RS -4M0--RS -4M0--8RS -5M0--RS -5M0--8RS -5M0--2RS -M0--RS -M0--8RS -M0--2RS -8M0--8RS -8M0--2RS -20M0--8RS -20M0--2RS -M0--2RS -M0--RS -25M0--2RS -25M0--RS -28M0--RS -28M0--20RS B-28M0--RS B-28M0--20RS 35. 40.4 4. 43.2 3. 4.4 42.2 44.2 42.2 42.9 45.0 44.5 45.5 47.5 52. 43.9 47.5 45.5 47.5 52.8 45.5 47.5 52.8 48.8 52. 50.5 52. 52. 54.9 57.7 59.7 9.9 72.9 72.5 77. 5.3.2 7.2.8 24.4 24.4 24.4 24.4 2.0 2.0 3.3 3. 3. 4.0 4.0 5.9.4.4 5.9 5.9..9.9.9 2.7.9 5..9 5.9 5.9 8.3 5.9 9.8 9.8 2.8 9.8 24. 4 9 4 9 5 9 9 35 24 24 35 24 35 35 30 35 35 4 35 4 4 50 4 54 30-30M0--20RS 7.7 39. 2.2 50 32-32M0--20RS 79.2 42.0 28. 50 38-38M0--24RS 90.9 49.4 3.8 55 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end.

Gaugeable Fittings and dapter Fittings Straight Fittings Male Connectors See page 8 for thread specifications. ISO/BSP parallel gaskets are available. See page 53. ISO/BSP Parallel (RP) ISO ➀ F, -200--2RP -200--4RP -400--2RP -400--4RP -80--RP -80--8RP -20--8RP -20--2RP.3.50.40.59.79.87.92 2.05 0.50 0.09 0.0 0.90 0.9 0. 0.9 0.3 0.4 0.47 0.2-0--RP 2.35.23 0.78 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. Bored-Through Fittings for Thermocouples, ip s, and Heat xchanger Tees 9/ 9/ / / 5/ Swagelok bored-through male connectors accommodate thermocouples or dip tubes. Most male connectors are available as a bored-through fitting, but male connectors whose pipe thread end is small relative to the tube fitting end such as -00--2 or -8M0--2RT cannot be bored through. Swagelok bored-through reducers and standard Swagelok tees can be used to create a heat exchanger tee. To order bored-through fittings, add BT to the ordering number. xample: SS-400--4BT Bored-through fittings have a reduced pressure rating. Contact your authorized Swagelok representative for details. 3 ISO, ➀ F, mm -3M0--2RP -3M0--4RP 33.3 38. 2.9 2.4 4-4M0--2RP 34.0 3.7 2.4 4 8 0 2 -M0--2RP -M0--4RP -M0--RP -M0--8RP -8M0--2RP -8M0--4RP -8M0--RP -8M0--8RP -0M0--4RP -0M0--RP -0M0--8RP -2M0--4RP -2M0--RP -2M0--8RP -2M0--2RP 35. 40.4 4.2 43.2 3.5 4.3 4.9 44. 42.2 42.9 45.0 45.4 45.4 47.5 52. 5.3.2 7.2.8 4.0 4.0 5.9.4.4 5.9 5.9 4 9 4 9 5 9 9 35 5-5M0--8RP 47.5 24.4.9 8 20 25 28 -M0--RP -M0--8RP -8M0--8RP -8M0--2RP -20M0--8RP -20M0--2RP -M0--2RP -M0--RP -25M0--2RP -25M0--RP -28M0--RP -28M0--20RP B-28M0--RP B-28M0--20RP 45.4 47.5 49.0 52.3 50.5 52.5 52.8 54.5 57.8 59.8 9.8 72.9 72.5 77. 24.4 24.4 2.0 2.0 3.3 3. 3..9.9 5..9 5.9 5.9 8.3 5.9 9.8 9.8 2.8 9.8 24. 24 35 30 35 35 4 35 4 4 50 4 54 30-30M0--20RP 7.8 39. 2.2 50 32-32M0--20RP 79.2 42.0 28. 50 38-38M0--24RP 92. 49.4 3.8 55 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end.

Straight Fittings Male Connectors Bulkhead NPT Gaugeable Fittings and dapter Fittings 7 NPT ➀ F Panel Hole Max Panel Thickness, -200--2.83 0.50 0.09 2/4 0.50-400--2.95-400--4 2.3 0.0 0.9 29/4 0.40-00--4-00-- -00--8-80-- -80--8 2.2 2.2 2.5 2.49 2.7 0. 0.90 0.38 0.4 37/4 0.44 5/ 49/4 0.50-20--2 3.00 0.9 0.2 3/ /4 0. -0-- 3.7.23 0.88 2/4 0.75, mm -M0--2 -M0--4 4 53. 5.3.5 0.2 2-2M0--8 8.8.8 24 2.7 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. O-ring dapts to S J92/ and ISO 92- straight thread boss. S/MS Straight (ST) S/MS 5/-24 7/-20 9/-8 5/-24 7/-20 9/-8 - -4 ➀ F, -200--2ST -200--4ST -200--ST -400--2ST -400--4ST -400--ST -400--8ST -400--0ST.8.24.3..34.40.48.0 0.50 0.09 0.0 0.09 0.9 0.9 0.9 0.9 7/ 9/ / 9/ / 5/ -20-500--5ST.37 0.4 0.25 7/-20 9/-8 - -4 9/-8 - -4 /-2 - -4 - /-2 5/-2-00--4ST -00--ST -00--8ST -00--0ST -80--ST -80--8ST -80--0ST -80--2ST -00--8ST -00--0ST -20--8ST -20--2ST -20--ST.40.4.54..54.5.77.93.5.78.8.93.9 0. 0.90 0.9 0.9 0.8 0.4 0.4 0.4 0.42 0.50 0.42 0.2 0.3 / 3/ 5/ / 3/-2-40--4ST.93.02 0.72 /-2 5/-2-0--2ST -0--ST 2.0 2.4.23 0. 0.88-2 -2000--20ST 2.9.2.09-2 -2400--24ST 3.0.97.34 2 2 2-2 -3200--32ST 4.00 2..8 2 0 2 S/MS ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. ➀ F, mm 9/-8 -M0--ST 35. 5.3 8 9/-8-7/-20 9/-8 - -0M0--ST -0M0--8ST -2M0--4ST -2M0--ST -2M0--8ST 37.3 39.4 40. 39.9 4.9 Long S/MS Straight (ST) 7.2.8 7. 5.2 7. 8 S/MS ➀ F Long S/MS Straight, 7/-20-400-L-4ST 2.2 0.0 0.9 9/ - -80-L-8ST 3.0 0.90 0.4 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end.

8 Gaugeable Fittings and dapter Fittings Straight Fittings Male Connectors O-ring O-ring O-Seal (S/MS Straight ) S/MS ➀ F, / 5/-24-00--OR.05 0.34 0.05 9/ 5/-24-200--OR.29 0.50 0.09 9/ 3/ -24-300--OR.35 0.54 0.2 7/-20-400--OR.5 0.0 0.9 5/ -20-500--OR.0 0.4 0.25 9/-8-00--OR.7 0. 5/ - -80--OR.8 0.90 0.4 /-2-20--OR 2.0 0.9 0.2 5/-2-0--OR 2.29.23 0.88 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. O-Seal (NPT) NPT ➀ F, -200--2-OR.29 0.50 0.09-400--2-OR -400--4-OR -00--4-OR -00---OR -00--8-OR.38.5.57.3.85 0.0 0.9 0. 5/ 5/ 5/ -80--8-OR.9 0.90 0.4 5/ ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. Mounting for O-Seal Fittings For a raised surface, see Fig.. The minimum diameter allows metal-to-metal contact outside of the O-ring sealing diameter to prevent O-ring extrusion. For a recessed hole that allows the round shoulder of the O-seal fitting into the recess, see Fig. 2. For a recessed hole that allows the hex of the O-seal fitting into the recess, see Fig. 3. Fig. Fig. 3 C ➀ ➀ Fig. 2 ➀ B ➀ llow clearance for full thread. S/MS NPT Min ia B Min ia C Min ia Max epth Max epth, 5/-24 0. 0.50 0.59 0. 0.09 5/-24 0. 0.9 0.78 0.88 0. -24 0.5 0. 0.75 0.09 0. 7/-20 0.9 0.78 0.88 0.87 0.97.09-20 0.75 0.9.03 0. 0.3 9/-8 0.8 0.97.09 0.87.00..3 0.34..34.53 0. 0.44 -.00..3 0. 0.34..34.53 0.44 /-2.4.53.75 0. 0.50 5/-2.9.78 2.03 0.5

Gaugeable Fittings and dapter Fittings 9 Straight Fittings Male Connectors N Fitting 37 N Flare ➀ F S, S / -00--2N.07 0.34 0.05 7/ 5/-24UNJF-3-200--2N -200--4N..38 0.50 0.0 0.09 7/ 5/-24UNJF-3 7/-20UNJF-3-400--4N.48 0.0 0.7 7/-20UNJF-3 5/ 5/ -500--5N.5 0.4 0.23 9/ -20UNJF-3-00--4N -00--N.5 0. 0.7 7/-20UNJF-3 9/-8UNJF-3-80--8N.8 0.90 0.39 3/ -UNJF-3-20--2N 2.0 0.9 0. /-2UNJ-3-0--N 2.42.23 0.84 5/-2UNJ-3 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. N Bulkhead Fitting 37 N Flare F S Panel Hole Max Panel Thickness S, -400--4N 2.2 0.0 0.7 7/-20UNJF-3 29/4 0.40-00--N 2.25 0. 9/-8UNJF-3 37/4 0.44-80--8N 2.59 0.90 0.39 5/ -UNJF-3 49/4 0.50-20--2N 3. 0.9 0. 3/ /-2UNJ-3 /4 0. -0--N 3.4.23 0.84 5/-2UNJ-3 2/4 0.75

20 Gaugeable Fittings and dapter Fittings Straight Fittings Male Connectors Gasket 0-32 ➀ F, -200--057 0.95 0.50 7/ 0.09-400--025.08 0.0 9/ ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. M5 3 0.8 ➀ F, mm -M0--004 29.2 5.3 2.0 4 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. Metric (RS) ➀ F, mm -M0--M0X.0RS -M0--M2X.0RS 3.3 40.4 5.3 3.2 2-2M0--MX.5RS 45.5.8 4 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. Weld Connectors Socket Weld B J Socket Weld B J, -200--2W.4 0.0 0.50 0.09 0.29-400--4W.32 0.0 0.9 0.48-00--W.48 0.3 0. 0.0-80--8W.2 0.38 0.90 0.4 0.73-20--2W.7 0.44 0.9 0.2.04-0--W 2.07 0.2.23 0.88.3

Gaugeable Fittings and dapter Fittings 2 Straight Fittings SWGLOK ML PIP WL CONNCTOR CUTWY-MS-0-40 C-PH-034-IM Weld Connectors Male Pipe Weld (Fractional) 37.5 J Pipe Weld ➀ F J, -200--2W.20 0.50 0.09 7/ 0.405 3/ -300--2W.23 0.54 0.2 7/ 0.405 5/ -400--2W -400--4W -500--2W -500--4W -00--4W -00--W -00--8W -00--2W -80--W -80--8W -80--2W -80--W.29.49.34.52.57.57.82.88.7.93.99 2.25 0.0 0.9 0.4 0.2 0.25 0. 0.90 0.4 9/ 9/ / / 3/ / 0.405 0.540 0.405 0.540 0.540 0.75 0.840.050 0.75 0.840.050.35-00--8W.93 0.9 0.50 5/ 0.840-20--8W -20--2W.99 0.9 0.55 0.2 / 0.840.050-0--W 2.45.23 0.88.35-2000--20W 3.04.2.09.0-2400--24W 3.50.97.34 2.900 2 2-3200--32W 4.47 2..8 2 2.375 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the weld end. Wall thickness at the weld end is based on schedule 80 pipe. Male Pipe Weld (Metric to Fractional) Pipe Weld ➀ F F, ➁ J, mm 3-3M0--2W 30.5 2.9 2.4 2 0.3 4-4M0--2W 3.2 3.7 2.4 2 0.3 8 0 2 -M0--2W -M0--4W -8M0--2W -8M0--4W -8M0--8W -0M0--4W -0M0--W -0M0--8W -2M0--4W -2M0--W -2M0--8W -2M0--2W 32.8 3 34.2 38.7 45. 40.9 40.9 4.5 43.4 43.4 49.0 50.5 5.3 4.2 7.2.8 5.4.4.4 7.5 7.5 5 5 8 8 9/ 9/ 9/ / / 3/ 3/ / 0.3 3.7 0.3 3.7 2.3 3.7 7. 2.3 3.7 7. 2.3 2.7 4-4M0--W 44. 24.4 0.7 24 5/ 7. 5-5M0--8W 49.0 24.4.9 24 5/ 2.3 -M0--8W 49.0 24.4 2.7 24 5/ 2.3 8-8M0--8W 50.5 24.4 3.9 / 2.3 30-30M0--20W 77.2 39. 2.2 4 4 mm 42.2 32-32M0--20W 79. 42.0 28. 4 4 mm 42.2 38-38M0--24W 9. 49.4 33.7 55 55 mm 48.3 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the weld end. Wall thickness at the weld end is based on schedule 80 pipe. ➁ This dimension is for steel and aluminum fittings.

Gaugeable Fittings and dapter Fittings Straight Fittings Female Connectors NPT / NPT / -00-7- -00-7-2-200-7-2 -200-7-4, F 0.93 0.9.3.32 0.34 0.05 0.50 0.09 7/ 9/ 9/ 3/ -300-7-2.7 0.54 0.2 9/ 5/ -400-7-2-400-7-4 -400-7- -400-7-8-500-7-2 -500-7-4-00-7-2 -00-7-4-00-7- -00-7-8-00-7-2 -80-7-4-80-7- -80-7-8-80-7-2 -00-7- -00-7-8-00-7-2 -20-7-8-20-7-2.23.4.48.7.2.45.29.48.54.73.88.59.5.84.90.5.84.90.84.90 0.0 0.9 0.4 0.25 0. 0.90 0.4 0.9 0.50 0.9 0.2 9/ / 9/ / 5/ 3/ / 5/ 5/ / 5/ / 5/ -40-7-2.9.02 0.72 5/ -0-7-2-0-7-2.0 2.45.23 0.88-2000-7-20 2.94.2.09 2-2400-7-24 3.28.97.34 2 2 2-3200-7-32 4.00 2..8 2 3 NPT F, mm -3M0-7-2-3M0-7-4 28.7 33.5 2.9 2.4 4-4M0-7-2 29.7 3.7 2.4 4 8 0 2 -M0-7-2 -M0-7-4 -M0-7- -M0-7-8-8M0-7-2-8M0-7-4-8M0-7- -8M0-7-8-0M0-7-4-0M0-7- -0M0-7-8-2M0-7-4-2M0-7- -2M0-7-8 3.3 35.8 37. 42.5 32. 37.0 38.5 43.3 37.8 39.4 44.2 40.3 4.9 4.7 5.3.2.4 7.2.8 4 9 4 9 5 9 9 5-5M0-7-8 4.7 24.4.9 -M0-7-8 4.9 24.4 2.7 20 25-20M0-7-8-20M0-7-2 -M0-7-2 -M0-7- -25M0-7-2-25M0-7- 4 49.7 49.7 5 53.4 2.3 2.0 5.9 2.0 8.3 3.3 2.8 30 35 35 4 35 4

Gaugeable Fittings and dapter Fittings 23 Straight Fittings Female Connectors See page 8 for thread specifications. ISO/BSP parallel thread (RJ) fittings are available in stainless steel only. See page 8 for thread specifications. ISO/BSP Tapered (RT) ISO F, -200-7-2RT.3 0.50 0.09 9/ -400-7-2RT -400-7-4RT -400-7-RT -400-7-8RT -00-7-4RT -00-7-RT -00-7-8RT -80-7-4RT -80-7-RT -80-7-8RT.23.4.48.7.48.54.73.59.5.84 0.0 0.9 0. 0.90 0.4 9/ / / 3/ /, mm 3-3M0-7-2RT 28.7 2.9 2.4 4 8 0 2 5 20 25 -M0-7-2RT -M0-7-4RT -M0-7-RT -M0-7-8RT -8M0-7-2RT -8M0-7-4RT -8M0-7-RT -8M0-7-8RT -0M0-7-2RT -0M0-7-4RT -0M0-7-RT -0M0-7-8RT -2M0-7-2RT -2M0-7-4RT -2M0-7-RT -2M0-7-8RT -2M0-7-2RT -5M0-7-RT -5M0-7-8RT -20M0-7-8RT -20M0-7-2RT -M0-7-2RT -M0-7-RT -25M0-7-2RT -25M0-7-RT 3.3 35.8 37. 42.5 32. 37.0 38.5 43.3 33.0 37.8 39.4 44.2 35.5 40.3 4.9 4.7 49.0 4.9 4.7 4 49.7 49.7 5 53.4 2.3 5.3.2.4 7.2.8 8.3 24.4.9 2.0 5.9 2.0 8.3 3.3 2.8 4 9 5 9 8 9 35 24 30 35 35 4 35 4 ISO/BSP Parallel (RJ) 5/ 8 0 2 ISO ISO/BSP Parallel (RP) ISO F, SS-400-7-4RJ SS-400-7-RJ SS-400-7-8RJ SS-500-7-4RJ SS-500-7-8RJ SS-00-7-4RJ SS-00-7-RJ SS-00-7-8RJ SS-80-7-4RJ SS-80-7-RJ SS-80-7-8RJ.48.48.7.5..54.52.5.5.75.90, mm SS-M0-7-4RJ SS-M0-7-RJ SS-M0-7-8RJ SS-8M0-7-4RJ SS-8M0-7-RJ SS-8M0-7-8RJ SS-0M0-7-4RJ SS-0M0-7-RJ SS-0M0-7-8RJ SS-2M0-7-4RJ SS-2M0-7-RJ SS-2M0-7-8RJ 37. 37. 43.5 38.5 3.2 4.0 39.4 38.8 42. 4.9 44.4 48.2 0.0 0.4 0. 0.90 See page 8 for thread specifications. 0.8 0.9 0.9 0. 0. 0.2 0. 0.2 5.3.2 7.2.8 5.5.5 7.0 5.5.5 7.0 5.5.5 7.0 5/ / / 5/ / 3/ 5/ / 9 24 9 24 9 24 24 F, mm -M0-7-2RP -M0-7-4RP 33.5 39.4 5.3 4 9 -M0-7-2RP 53.3 2.0 8.3 35 25-25M0-7-RP 3.9 2.5 2.8 40

24 Gaugeable Fittings and dapter Fittings Straight Fittings Female Connectors See page 8 for thread specifications. ISO/BSP parallel gaskets are available. See page 53. ISO/BSP Parallel (RG, Gauge) ISO F, -200-7-4RG.39 0.59 0.09 5/ -400-7-2RG -400-7-4RG -400-7-RG -400-7-8RG -500-7-4RG -500-7-8RG -00-7-4RG -00-7-RG -00-7-8RG -80-7-RG -80-7-8RG.2.48.48.7.5..54.52.5.75.90 0.0 0.4 0. 0.90 0.8 0.9 0.9 0.9 0. 0. 0.2 0.2 9/ 5/ / / 5/ / 5/ /, mm 3-3M0-7-4RG 35.3 2.9 2.4 9 8 0 2 -M0-7-2RG -M0-7-4RG -M0-7-RG -M0-7-8RG -8M0-7-4RG -8M0-7-RG -8M0-7-8RG -0M0-7-4RG -0M0-7-RG -0M0-7-8RG -2M0-7-4RG -2M0-7-RG -2M0-7-8RG 32.0 37. 37. 43.5 38.5 3.2 4.0 39.4 38.8 42. 4.9 44.4 48.2 5.3.2 7.2.8 4.5 5.5.5 7.0 5.5.5 7.0 5.5.5 7.0 4 9 24 9 24 9 24 24 20-20M0-7-8RG 54.3 2.0 7.0 30 -M0-7-8RG 54.3 2.0 7.0 30 Bulkhead NPT NPT F Panel Hole Max Panel Thickness, -200-7-2.7 0.50 0.09 9/ 2/4 0.50-400-7-2 -400-7-4.85 2.04 0.0 0.9 29/4 0.40-00-7-4 2.7 0. 37/4 0.44-80-7- -80-7-8 2.43 2.2 0.90 0.4 5/ / 49/4 0.50, mm -M0-7-4 5.8 5.3 9.5 0.2 2-2M0-7-8.5.8 2.7

Gaugeable Fittings and dapter Fittings 25 Straight Fittings SWGLOK OVR " RUCR CUTWY-MS-0-40 C-PH-0475-IM Reducers G flat T Tx T Tx T Tx and Under Over 25 mm and Under Reducer (Fractional) T Tx F G / 3/ 5/ / 3/ 3/ 5/ 2 2-00-R-2-00-R-4-200-R- -200-R-2-200-R-3-200-R-4-200-R- -200-R-8-300-R-2-300-R-4-400-R-2-400-R-3-400-R-4-400-R-5-400-R- -400-R-8-400-R-0-400-R-2-500-R- -500-R-8-00-R-4-00-R- -00-R-8-00-R-0-00-R-2-80-R-4-80-R- -80-R-8-80-R-0-80-R-2-80-R- -00-R-2-00-R-4-00-R- -20-R-8-20-R- -0-R-20➀ -0-R-24➀ -0-R-32➀ -2000-R-24➀ -2000-R-32➀,.5.24.4.32.35.42.48.74.37.4.45.48.54.57.0.82.89.88.5.87.3.70.9.98.98.77.84 2.0 2.2 2.2 2.37 2.5 2.2 2.40 2.5 2.4 3.7 3.5 4.43 4.0 4.93 ➀ Furnished with nut and preswaged ferrules. 0.34 0.05 5/ 0.50 0.54 0.0 0.03 0.08 0.09 0.09 0.09 0.09 0.08 0.2 0.08 0.2 0.7 0.9 0.9 0.9 0.9 0.9 7/ 7/ 7/ 7/ 7/ 9/ 7/ 9/ / 3/ 0.4 0.25 9/ 0. 0.90 0.7 0. 0.7 0. 0.37 0.4 0.4 0.4 0.9 0.50 0.9 0.37 0.2.23 0.88.2.09 / 3/ 3/ 3/ 3/ 3/ 3/ / 5/ 5/ / / 2 2 2 3 2 3 2-2400-R-32➀ 5.7.97.34 2 3 Reducer (Metric) T Tx F, mm 2 3-2M0-R-3M 33.5 2.9.7 2 3 4 0-3M0-R-4M -3M0-R-M -3M0-R-0M 35.0 3. 38.4 2.9 2.4 4-4M0-R-M 37. 3.7 2.4 2 8 0 2 3 8 0 2 8 0 2 8 2 5 8 8 0 8 20 25 -M0-R-3M -M0-R-8M -M0-R-0M -M0-R-2M -M0-R-8M -8M0-R-M -8M0-R-0M -8M0-R-2M -0M0-R-M -0M0-R-8M -0M0-R-2M -0M0-R-5M -0M0-R-8M -2M0-R-M -2M0-R-8M -2M0-R-0M -2M0-R-M -2M0-R-8M -2M0-R-20M -2M0-R-M -2M0-R-25M 3.9 39.9 40.7 4.3 49. 40.3 42.0 47. 42.4 43.4 49.8 5.3 5.3 44.9 45.9 4.7 53.8 53.8 5. 5. 2.4 5.3.2 7.2.8.9 4..4.4 4. 5. 4. 5. 7. 2 2 4 4 4 4 4 5 8 8 8 8 24 2 -M0-R-2M 53.0 24.4 8.8 24 8 20 25 2 20 25 8 25 8 20 25 8 20-8M0-R-2M -8M0-R-M -8M0-R-20M -8M0-R-M -8M0-R-25M -20M0-R-M -20M0-R-8M -20M0-R-M -20M0-R-25M -M0-R-8M -M0-R-20M -M0-R-25M -25M0-R-8M -25M0-R-20M 54. 5. 57. 57. 2.4 5 5 59.4 4.2 5 59.4 4.2 3. 4. 24.4 2.0 2.0 3.3 8.8 2.0 5. 5. 5. 2.0 3.9 5.9 5.9 3.9 5.5 8.3 3.9 5.5 30 30 35

2 Gaugeable Fittings and dapter Fittings Straight Fittings Reducers T Tx T Tx Reducer (Metric to Fractional) T Tx, F, mm 2-2M0-R-2 33.5 2.9.7 2 3-3M0-R-2-3M0-R-4 33.5 3. 2.9 2.0 2.4 4-4M0-R-4 37. 3.7 2.4 2 8 0 2 8 5/ -M0-R-2 -M0-R-4 -M0-R-5 -M0-R- -M0-R-8-8M0-R-4-8M0-R- -8M0-R-8-0M0-R- -0M0-R-8-2M0-R-8-2M0-R-2-8M0-R-2-8M0-R- 3.9 39.2 39.9 40.7 4.3 40.3 42.0 47. 44.2 49.8 52.3 53.8 5. 2.4 5.3.2 7.2.8 24.4 2.0 4.4 4.4.4.4.8 9.3 4.7 5. 25-25M0-R- 3.3 20.2 35 2 4 5 8 Reducer (Fractional to Metric) T Tx, mm F, -200-R-M.42 0.50 0.09 7/ Long Reducer T Tx T Tx F, -00-RF-8 2.57 0. 0.25 Use only long reducers in female Swagelok end connections. Bulkhead Reducer F Panel Hole Max Panel Thickness, -200-R-2.95 0.50 0.08 2/4 0.50-400-R-4 2.20 0.0 0.7 29/4 0.40-00-R- 2.4 0. 0. 37/4 0.44-80-R-8 2.87 0.90 0.37 5/ 49/4 0.50-00-R-0 2.9 0.9 0.47 / 57/4 0.50-20-R-2 3.2 0.9 0.58 3/ /4 0. -0-R- 3.95.23 0.80 2/4 0.75

Straight Fittings Port Connectors Port Connector Gaugeable Fittings and dapter Fittings H /25 mm and under H Over /25mm ➀ Furnished with nuts and preswaged ferrules., / -0-PC 0.03 0.54-20-PC 0.08 0.88-40-PC 0.7 0.98 5/ -50-PC 0..02-0-PC 0..05-8-PC 0.37.43-0-PC 0.47.49-2-PC 0.58.49 --PC 0.80.94-2000-PC➀.02 2.72-2400-PC➀.25 3.3 2-3200-PC➀.72 4.5 H, mm 3-3M-PC.9.2 -M-PC 4. 25.0 8-8M-PC 5. 2.0 0-0M-PC 7.. 2-2M-PC 8.8 3.2 5-5M-PC.2 37.8 -M-PC 2.0 37.8 8-8M-PC 3.9 37.8 20-20M-PC 5.5 39.4 25-25M-PC 9.9 49.3 28-28M0-PC➀.5 3.5 30-30M0-PC➀ 24.3 7. 32-32M0-PC➀ 2.5 9.7 38-38M0-PC➀ 3. 8.9 H ➀ Furnished with nuts and preswaged ferrules. Reducing Port Connector T H Tx T Tx H, / -20-PC- 0.03 0.72 / -40-PC- -40-PC-2-0-PC-2-0-PC-4-8-PC-4-8-PC- 0.03 0.08 0.08 0.7 0.7 0. 0.75 0.90 0.92.00.7.2-2-PC-8 0.37.49 --PC-8 --PC-2 0.37 0.58.9.72 T Tx H, mm 3 -M-PC-3M.9.9 8-8M-PC-M 4. 25.4 0 2 8 8 0-0M-PC-M -0M-PC-8M -2M-PC-M -2M-PC-8M -2M-PC-0M 4. 5. 4. 5. 7. 25.8 2.3 29. 30. 30. 2 -M-PC-2M 8.8 37.5 28 25-28M-PC-25M 9.8 5.5 32 25-32M-PC-25M 9.8 0.3 38 25-38M-PC-25M 9.8 5.8

28 Gaugeable Fittings and dapter Fittings Straight Fittings Caps and Plugs Cap Plug, / -00-C 0.59 0.34-200-C 0.79 0.50 3/ -300-C 0.84 0.54-400-C 0.92 0.0 5/ -500-C 0.9 0.4-00-C.0 0. -80-C.2 0.90-00-C.24 0.9-20-C. 0.9-40-C.37.02-0-C..23-80-C..23-2000-C 2.0.2-2400-C 2.54.97 2-3200-C 3.4 2., mm 2-2M0-C 20. 2.9 3-3M0-C 20. 2.9 4-4M0-C 2.3 3.7 -M0-C 23. 5.3 8-8M0-C 24.5.2 0-0M0-C 2. 7.2 2-2M0-C 30..8 4-4M0-C 3.4 24.4 5-5M0-C 3.4 24.4 -M0-C 3.4 24.4 8-8M0-C 32.2 24.4 20-20M0-C 3 2.0 -M0-C 3 2.0 25-25M0-C 4.0 3.3 28-28M0-C 48.5 3. B-28M0-C 4.2 3. 30-30M0-C 53.4 39. 32-32M0-C 55.8 42.0 38-38M0-C 5.4 49.4, / -00-P -200-P 3/ -300-P -400-P 5/ -500-P -00-P -80-P -00-P -20-P -40-P -0-P -2000-P -2400-P 2-3200-P, mm 2-2M0-P 3-3M0-P 4-4M0-P -M0-P 8-8M0-P 0-0M0-P 2-2M0-P 5-5M0-P -M0-P 8-8M0-P 20-20M0-P -M0-P 25-25M0-P 28-28M0-P 30-30M0-P 32-32M0-P 38-38M0-P Vent Protectors 40 mesh wire screen 40 mesh 300 series stainless steel wire screen assembly Mud auber Swagelok vent protectors, more commonly known as mud dauber fittings, protect open ends of instruments, tubing, outlet vents, and bleed-off lines. The mesh wire screen prevents foreign objects, such as mud dauber insects, from entering and clogging various systems and causing damage. Vent protectors are available in stainless steel and brass. To order brass, replace SS in the ordering number with B. xample: B-M-2 NPT F, SS-M-2 0.5 0.9 SS-M-4 0.78 9/ SS-M- 0.8 0.4 / SS-M-8.03 0.50 SS-M-2.0 0.72 /

Gaugeable Fittings and dapter Fittings 29 90 lbows Unions ports are identical. F, / -00-9 0.70 0.34 0.05-200-9 0.88 0.50 0.09 3/ -300-9.00 0.54 0.2-400-9.0 0.0 0.9 5/ -500-9.3 0.4 0.25 9/ -00-9.20 0. -80-9.42 0.90 0.4 3/ -00-9.50 0.9 0.50 5/ -20-9.57 0.9 0.2 / -40-9.7.02 0.72-0-9.93.23 0.88-80-9 2.7.23 0.97 / -2000-9 2.7.2.09 / -2400-9 3.0.97.34 2 2-3200-9 4. 2..8 2 F,, mm 3-3M0-9.3 2.9 2.4 4-4M0-9 25.4 3.7 2.4 -M0-9.0 5.3 8-8M0-9 28.8.2.4 9/ 0-0M0-9 3.5 7.2 / 2-2M0-9 3.0.8 3/ 4-4M0-9 38.0 24.4. 5/ 5-5M0-9 38.0 24.4.9 5/ -M0-9 38.0 24.4 2.7 5/ 8-8M0-9 39.8 24.4 5. / 20-20M0-9 44. 2.0 5.9 -M0-9 44. 2.0 8.3 25-25M0-9 49. 3.3 2.8 28-28M0-9 4.0 3. 2.8 4 mm B-28M0-9 55.4 3. 24. / 30-30M0-9 9.9 39. 2.2 4 mm 32-32M0-9 72.3 42.0 28. 4 mm 38-38M0-9 84.0 49.4 33.7 55 mm 50-50M0-9 0 5.0 45.2 2

30 Gaugeable Fittings and dapter Fittings 90 lbows Male See page 8 for thread specifications. NPT / 3/ 5/ NPT / / / ➀ F, -00-2- 0.75 0.34 0.05 7/ -00-2-2-200-2- -200-2-2-200-2-4 -300-2-2-300-2-4 -400-2- -400-2-2-400-2-4 -400-2- -400-2-8-500-2-2 -500-2-4-500-2- -00-2-2-00-2-4 -00-2- -00-2-8-00-2-2 -80-2-4-80-2- -80-2-8-80-2-2 -00-2- -00-2-8-00-2-2 -20-2-8-20-2-2 0.93 0.93 0.97 0.50 0.09 7/ 7/.00 0.54 0.2.0.0.0.7.25.3.3.20.20.20.23.3.4.42.42.42.57.50.50.57 0.0 0.4 0. 0.90 0.9.57 0.9 0.2 0.9 0.9 0.9 0.9 0.9 0.25 0.25 0.9 0.38 0.4 0.4 0.38 0.47 0.50 0.47 0.2 / 3/ 9/ 9/ / / 3/ / 3/ 3/ 3/ / 5/ 5/ / / -40-2-2.7.02 0.2-0-2-2 -0-2-.93.23 0.2 0.88-2000-2-20 2.7.2.09 / -2400-2-24 3.0.97.34 2 2 2-3200-2-32 4. 2..8 2 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. 3 4 8 0 2 NPT ➀ F,, mm -3M0-2-2-3M0-2-4-4M0-2-2-4M0-2-4 -M0-2-2 -M0-2-4 -M0-2- -M0-2-8-8M0-2-2-8M0-2-4-8M0-2- -8M0-2-8-0M0-2-2-0M0-2-4-0M0-2- -0M0-2-8-2M0-2-4-2M0-2- -2M0-2-8-2M0-2-2 23. 24. 2.9 2.4 7/ 25.4 3.7 2.4.0.0 29.8 3.8 28.8 28.8 30. 32. 3.5 3.5 3.5 33.5 3.0 3.0 3.0 39.8 5.3.2 7.2.8.4.4.4 7. 7. / 3/ 9/ 9/ / 3/ / / / 3/ 3/ 3/ 3/ / 5-5M0-2-8 38.0 24.4.9 5/ 8 20 25 -M0-2- -M0-2-8 -M0-2-2-8M0-2-8-8M0-2-2-20M0-2-8-20M0-2-2 -M0-2-2 -M0-2- -25M0-2-2-25M0-2- 38.0 38.0 39.8 24.4 39.8 24.4 44. 2.0 44. 2.0 49. 3.3.9 2.7.9 5..9 5.9 5.9 8.3 5.9 2.8 5/ 5/ / / 30-30M0-2-20 9.9 39. 2.2 4 mm 32-32M0-2-20 72.3 42.0.8 4 mm 38-38M0-2-24 84.0 49.4 33.7 55 mm ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end.

90 lbows Male Gaugeable Fittings and dapter Fittings 3 See page 8 for thread specifications. ISO/BSP Tapered (RT) ISO ➀ F, -200-2-2RT -200-2-4RT -400-2-2RT -400-2-4RT -400-2-RT -400-2-8RT 0.83 0.97.0.0.7.25 0.50 0.09 0.0 0.9 7/ / 3/ 5/ -500-2-4RT.3 0.4 0.25 9/ -00-2-2RT -00-2-4RT -00-2-RT -80-2-4RT -80-2-RT -80-2-8RT.20.20.23.42 0.90 0. 0.38 0.4 / 3/ -20-2-8RT.57 0.9 0.47-0-2-RT.93.23 0.88 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. 3 4 8 0 2 ISO ➀ F, mm -3M0-2-2RT -3M0-2-4RT -4M0-2-2RT -4M0-2-4RT -M0-2-2RT -M0-2-4RT -M0-2-RT -M0-2-8RT -8M0-2-2RT -8M0-2-4RT -8M0-2-RT -8M0-2-8RT -0M0-2-4RT -0M0-2-RT -0M0-2-8RT -2M0-2-2RT -2M0-2-4RT -2M0-2-RT -2M0-2-8RT -2M0-2-2RT 23. 24. 2.9 2.4 7/ 25.4 3.7 2.4.0.0 29.8 3.8 28.8 28.8 30. 32. 3.5 3.5 33.5 3.0 3.0 3.0 3.0 39.8 5.3.2 7.2.8.4.4.4 7. 7. / 3/ 9/ 9/ / 3/ / / 3/ 3/ 3/ 3/ 3/ / 4-4M0-2-8RT 38. 24.4. 5/ 5-5M0-2-8RT 38. 24.4.9 5/ 8 20 25 -M0-2-RT -M0-2-8RT -8M0-2-8RT -8M0-2-2RT -20M0-2-8RT -20M0-2-2RT -M0-2-2RT -M0-2-RT -25M0-2-2RT -25M0-2-RT 38.0 24.4 39.8 24.4 44. 2.0 44. 2.0 49. 3.3.9.9 5..9 5.9 5.9 8.3 5.9 2.8 5/ / -28M0-2-RT 4.0 3. 2.8 4 mm 28 B-28M0-2-RT 55.4 3..2 / ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. T Reducing T Tx F,, mm -M0-2R-M.0 5.3 4. 2 2-2M0-2R-2M 38..8 8.8 5/ Tx

32 Gaugeable Fittings and dapter Fittings 90 lbows Male Positionable, ISO/BSP Parallel (PR) O-ring U retainer Fx flat ISO -400-2-2PR -400-2-4PR -00-2-4PR -00-2-PR -80-2-4PR -80-2-PR -80-2-8PR ➀ F, Fx, U,.0.4.20.3.42.42.50 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. 0.0 0. 0.90 0. 0.9 0.23 0.23 0.3 0.4 3/ 3/ 3/ 5/ 9/ / 0.0 0.80 0.80 0.9 0.80 0.9. -00-2-8PR.50 0.9 0.47 5/ /. 8 0 2-20-2-8PR -20-2-2PR -0-2-2PR -0-2-PR -M0-2-2PR -M0-2-4PR -8M0-2-2PR -8M0-2-4PR -0M0-2-4PR -0M0-2-PR -2M0-2-4PR -2M0-2-PR -2M0-2-8PR -2M0-2-2PR.57 0.9.93.23, mm.0 29.0 5.3 28.8 29.9.2 33.5 7.2 3.0 3.0 38.0 39.8.8 0.47 0.2 0.2 0.78 4.0 4.0 5.9 5.9 5.9 / 9/ 3/ 3/ 3/ 5/ / / 9/ 9/ /..43.43.82 5.2 20.3 5.2 20.3 20.3 24.4 20.3 24.4 2 3.3 Positionable, S/MS Straight (ST) O-ring U washer S/MS positionable fittings are available in carbon steel and stainless steel only. dapts to S J92/ and ISO 92 straight thread boss. Fx flat S/MS 7/-20 9/-8-400-2-4ST -400-2-ST ➀ F, Fx, U,.2.20 0.0 0.9-4 -00-2-0ST.5 0.9 0.50 5/. /-2-20-2-2ST.3 0.9 0.2 /.44 3/-2-40-2-4ST.70.02 0.72 3/.59 5/-2-0-2-ST.99.23 0.88.73-2 -2000-2-20ST 2.7.2.09 / 2. -2-2400-2-24ST 3.07.97.34 2 2 2.45 2 2-2 -3200-2-32ST 4. 2..8 2 2 3. ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. 9/ / 0.5 0.79 5/ -20-500-2-5ST.9 0.4 0.23 9/ 0.72 7/-20 9/-8-9/-8 - -00-2-4ST -00-2-ST -00-2-8ST -80-2-ST -80-2-8ST.2.2.37 0..48 0.90 0.20 0.4 3/ 3/ 9/ / / 0.5 0.79.0 0.79.0

Gaugeable Fittings and dapter Fittings 33 90 lbows Weld Socket Weld Socket Weld B F K, -400-9-4W.0 0.0 0.9 0.50 K B -00-9-W.20 0.3 0. 0.3-80-9-8W.42 0.38 0.90 0.4 3/ 0.8-20-9-2W.57 0.44 0.9 0.2 /.0-0-9-W.93 0.2.23 0.88.38 Male Pipe Weld Pipe Weld ➀ F J, 37.5 J -400-2-2W -400-2-4W.0 0.0 0.9 0.405 0.540-00-2-4W.20 0. 0.540-80-2-8W.42 0.90 0.4 3/ 0.840-20-2-2W.57 0.9 0.2 /.050 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the weld end. Wall thickness at the weld end is based on schedule 80 pipe. Female NPT NPT F, -200-8-2-200-8-4 0.97.08 0.50 0.09 / 3/ -300-8-2.00 0.54 0.2 5/ -400-8-2-400-8-4 -400-8- -400-8-8-500-8-2 -500-8-4-00-8-2 -00-8-4-00-8- -00-8-8-80-8-4 -80-8- -80-8-8-00-8- -00-8-8-20-8-8 -20-8-2.0.7.25.3.3.20.20.23.3.42.42.42.53.50.57.57.7 0.0 0.9 0.4 0.25 0. 0.90 0.4 0.9 0.50 0.9 0.2 / 3/ 9/ / / 3/ 3/ 3/ 5/ / / -40-8-2.7.02 0.72-0-8-2 -0-8-.93 2..23 0.88 / 0 2 NPT F,, mm -M0-8-2 -M0-8-4 -M0-8-8.0 29.8 34. 5.3 / 8-8M0-8-4 30..2.4 / -0M0-8-2-0M0-8-4-2M0-8-4-2M0-8-8 3.5 33.5 3.0 38.8 7.2.8 / 3/ 3/ -M0-8-8 3 24.4 2.7 /

34 Gaugeable Fittings and dapter Fittings 45 lbows Male NPT NPT ➀ F, -400-5-2 0.97 0.0 0.9-400-5-4 -00-5-2.0 0.9-00-5-4.0 0. -00-5-.5 3/ -80-5- 0.38.2 0.90-80-5-8 0.4 3/ -20-5-2.33 0.9 0.2 / -0-5-.59.23 0.88 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. Positionable, S/MS Straight (ST) O-ring U washer S/MS ➀ F U, 7/-20-400-5-4ST.0 0.0 0.9 0.5 9/-8-00-5-ST.0 0. 0.79 - -80-5-8ST.2 0.90 0.4 3/.0 /-2-20-5-2ST.33 0.9 0.2 /.44 5/-2-0-5-ST.59.23 0.88.73 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. S/MS positionable fittings are available in carbon steel and stainless steel only. dapts to S J92/ and ISO 92 straight thread boss.

Tees Unions Gaugeable Fittings and dapter Fittings 35 x x Union x F, / -00-3.40 0.70 0.34 0.05-200-3.7 0.88 0.50 0.09 3/ -300-3.92 0.9 0.54 0.2 7/ -400-3 2.2.0 0.0 0.9 5/ -500-3 2.34.7 0.4 0.25-00-3 2.40.20 0. -80-3 2.84.42 0.90 0.4 3/ -00-3 3.0.53 0.9 0.50-20-3 3.4.57 0.9 0.2 / -40-3 3.52.7.02 0.72-0-3 3.8.93.23 0.88-80-3 4.34 2.7.23 0.97 / -2000-3 5.34 2.7.2.09 / -2400-3.20 3.0.97.34 2 2-3200-3 8.44 4. 2..8 2 x F,, mm 2-2M0-3 44.7.3 2.9.7 3-3M0-3 44.7.3 2.9 2.4 4-4M0-3 50.8 25.4 3.7 2.4 -M0-3 53.9.0 5.3 8-8M0-3 59.7 29.9.2.4 0-0M0-3 3.0 3.5 7.2 / 2-2M0-3 72.0 3.0.8 3/ 4-4M0-3 77. 38.8 24.4. 5-5M0-3 77. 38.8 24.4.9 -M0-3 77. 38.8 24.4 2.7 8-8M0-3 79. 39.8 24.4 5. / 20-20M0-3 89.3 44. 2.0 5.9 -M0-3 89.3 44. 2.0 8.3 25-25M0-3 98.3 49. 3.3 2.8 28-28M0-3 28 4.0 3. 2.8 4 mm B-28M0-3 03 5.4 3. 24. / 30-30M0-3 40 9.9 39. 2.2 4 mm 32-32M0-3 45 72.3 42.0 28. 4 mm 38-38M0-3 8 84.0 49.4 33.7 55 mm 50-50M0-3 2 0 5.0 45.2 2 x x Tx T Reducing Union (Fractional) T Tx x x F, -00-3--4 2.40.4 0. 0.0 0.9-80-3-8-4-80-3-8- 2.84.25.3 0.90 0.0 0. 0.9-00-3-0- 3.0.42 0.9 0. -20-3-2- -20-3-2-8 -0-3-- -0-3--8-0-3--2 3.4 3.8.4.57.5.7.7 0.9.23 0. 0.90 0. 0.90 0.9 0.4 0.4 0.2 3/ / -2000-3-20-5.34 2.7.2.23 0.88 / -2400-3-24-.20 2.3.97.23 0.88 2 2-3200-3-32- 8.44 2.79 2..23 0.88 2

3 Gaugeable Fittings and dapter Fittings Tees Unions Reducing Union (Metric) x x Tx T T Tx x x F,, mm 3-3M0-3-3M-M 49.3 2.9 2.9 5.3 2.4 8-8M0-3-8M-M 59.9 29.0.2 5.3 0-0M0-3-0M-M 3.0 29.7 7.2 5.3 / 2-2M0-3-2M-M 72.0 3.8.8 5.3 3/ 5-5M0-3-5M-2M 77.7 38.9 24.4.8 -M0-3-M-2M 77. 38.9 24.4.8 8 2-8M0-3-8M-2M 79.8 39.9 24.4.8 / -M0-3-M-2M 89.4 44.7 2.0.8 25-25M0-3-25M-2M 98.0 44.7 3.3.8 x T x Tx Reducing Union T Tx x y x F, -00-3-4-2.34.20.4 0. 0.0 0.9 x T y y T x Tx T Tx x y x F, -80-3-- 2.73.42.3 0.90 0. 3/ -00-3-- 2.95.53.42 0.9 0. -20-3-- 3.03.57.4 0.9 0. / x Tx y y T x x Tx T Tx Tx x y y x x F, -00-3-8-3.0.53.53.42 0.9 0.90-20-3-8- 3.4.57.57.4 0.9 0.90 0. / -0-3-2-3.9.93.7.5.23 0.9 x Tx y

Gaugeable Fittings and dapter Fittings 37 Tees Male Branch, NPT (TTM) NPT ➀ F, H, H -200-3TTM -200-3-4TTM.8.94 0.50 0.09 7/ 0.70 0.92 3/ -300-3TTM.92 0.54 0.2 7/ 0.70-400-3TTM -400-3-4TTM 2.2 0.0 0.9 0.74 0.92 5/ -500-3TTM 2.34 0.4 0.9 0.82-00-3TTM -00-3-TTM 2.40 2.2 0. 3/.00. -80-3TTM -80-3-8TTM 2.84 0.90 0.38 0.4 3/..30-00-3TTM 3.0 0.9 0.47.4-20-3TTM 3.4 0.9 0.2 /.45, mm -M0-3TTM -M0-3-4TTM 53.9 5.3 8.8 23.4 8-8M0-3TTM -8M0-3-4TTM 59.7.2.4 20.8 25.4 0-0M0-3TTM 7.0 7.2 7. 3/ 2.2 2-2M0-3TTM -2M0-3-4TTM -2M0-3-8TTM 72.0.8 7. 3/ 28.2 28.2 33.0 -M0-3TTM 77. 24.4.9 35.8 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. Run, NPT (TMT) NPT x ➀ F,, x -200-3TMT -200-3-4TMT.3.89 0.93 0.97 0.50 0.09 7/ 3/ -300-3TMT. 0.9 0.54 0.2 7/ x -400-3TMT -400-3-4TMT.80.98.0 0.0 0.9 5/ -500-3TMT.99.7 0.4 0.9-00-3TMT -00-3-TMT 2.20 2.42.20.3 0. 3/ -80-3TMT -80-3-8TMT 2.53 2.72.42 0.90 0.38 0.4 3/ -00-3TMT 2.88.50 0.9 0.47 5/ -20-3TMT 3.02.57 0.9 0.2 /, mm -M0-3TMT -M0-3-4TMT 45.8 50.3.0 5.3 8-8M0-3-4TMT 55.3 29.9.2.4 2-2M0-3-4TMT -2M0-3-8TMT 4.2 9.0 3.0.8 7. 3/ -M0-3TMT 73. 38.0 24.4.9 5/ ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end.

38 Gaugeable Fittings and dapter Fittings Tees Male H O-ring U washer x Fx flat S/MS positionable fittings are available in carbon steel and stainless steel only. dapts to S J92/ and ISO 92 straight thread boss. Positionable Branch, S/MS Straight (TTS) S/MS x ➀ F Fx H U, 7/-20-400-3TTS 2.24.2 0.0 0.9 9/.2 0.5 9/-8-00-3TTS 2.52.2 0. /. 0.79 - -80-3TTS 2.9.48 0.90 0.4 3/.49.0 /-2-20-3TTS 3.2.3 0.9 0.2 /.92.44 5/-2-0-3TTS 3.98.99.23 0.88 2..73-2 -2000-3TTS 5.34 2.7.2.09 / 2.29 2. -2-2400-3TTS.4 3.07.97.34 2 2 2.45 2.45 2 2-2 -3200-3TTS 8.44 4. 2..8 2 2 2.77 3. ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/ straight thread end. Positionable Branch, ISO/BSP Parallel (TTR) H O-ring x U retainer ports are identical. See page 8 for thread specifications. Fx flat ISO -400-3TTR -400-3-4TTR x ➀ F, Fx, H U, 2.2 2.28.0.4 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/ straight thread end. 0.0 0. 0.9 9/.04. 0.0 0.80-00-3TTR 2.40.20 0. 0.23. 0.80-80-3TTR -80-3-8TTR 2.84 3.00.42.50 0.90 0.3 0.4 3/ 5/ /.4.7 0.9. -00-3TTR 3.00.50 0.9 0.47 5/ /.7. -20-3TTR -20-3-8TTR 3.4.57 0.9 0.2 0.47 / /.92.78.43. -0-3TTR 3.8.93.23 0.78 2..92, mm 8 -M0-3TTR -M0-3-4TTR -8M0-3TTR -8M0-3-4TTR 53.9 58.0 57.7 59.7.0 29.0 5.3 30.0.2 4.0 4.0 5.9 9/ 9/ 9/ 2.4 32.2 28.4 32.3 5.2 20.3 5.2 20.3 0-0M0-3TTR 7.0 33.5 7.2 5.9 3/ 35. 20.3 2-2M0-3TTR -2M0-3-8TTR 72.0 7. 3. 38..8 3/ 5/ / 37. 43.4 24.4 2 x x Fx flat O-ring S/MS positionable fittings are available in carbon steel and stainless steel only. dapts to S J92/ and ISO 92 straight thread boss. U washer Positionable Run, S/MS Straight (TST) S/MS x ➀ F Fx U, 7/-20-400-3TST 2.24.2 0.0 0.9 9/ 0.5 9/-8-00-3TST 2.53.2 0. / 0.79 - -80-3TST 2.97.48 0.90 0.4 3/.0 /-2-20-3TST 3.55.3 0.9 0.2 /.44 5/-2-0-3TST 4.0.99.23 0.88.73-2 -2000-3TST 4.9 2.7.2.09 / 2. -2-2400-3TST 5.45 3.07.97.34 2 2 2.45 2 2-2 -3200-3TST 7.04 4. 2..8 2 2 3. ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end.

Tees Male Fx flat x O-ring x See page 8 for thread specifications. U retainer Positionable Run, ISO/BSP Parallel (TRT) ISO -400-3TRT -400-3-4TRT Gaugeable Fittings and dapter Fittings 39 x ➀ F, Fx, U, 2.0 2.4.0.4 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. 0.0 0. 0.9 9/ 0.0 0.80-00-3TRT 2.47.20 0. 0.23 0.80-80-3TRT -80-3-8TRT 2.88 3.2.42.50 0.90 0.3 0.4 3/ 5/ / 0.9. -00-3TRT 3.2.50 0.9 0.47 5/ /. -20-3TRT -20-3-8TRT 3.49 3.35.57 0.9 0.2 0.47 / /.43. -0-3TRT 4.04.93.23 0.78.82, mm 8 -M0-3TRT -M0-3-4TRT -8M0-3TRT -8M0-3-4TRT 53.4.2 5.3 2..0 29.0 28.8 29.9 5.3.2 4.0 4.0.4 9/ 9/ 9/ 5.2 20.3 5.2 20.3 0-0M0-3TRT 8. 33.5 7.2 5.9 3/ 20.3 2-2M0-3TRT -2M0-3-8TRT 73. 8.5 3.0 38.0.8 3/ 5/ / 24.4 2 Female Run, NPT (TFT) x x ports are identical. NPT x F,, -200-3TFT.72 0.97 0.50 0.09-400-3TFT.8.0 0.0 0.9-400-3-4TFT 2.05.7 / -00-3TFT 2..23 0. / -80-3TFT -80-3-8TFT 2.30 2.9.42.57 0.90 0.4 3/ / -20-3TFT 3.0.7 0.9 0.2 8-0-3-2TFT -0-3TFT -M0-3TFT -M0-3-4TFT -8M0-3TFT -8M0-3-4TFT 3.8 3..93 2., mm 4.0 52. 48.9 53.0.0 29.8 29.9 30..23 0.88 5.3.2.4 / / / 0-0M0-3TFT 55.9 33.5 7.2 3/ 2-2M0-3-4TFT -2M0-3TFT -2M0-3-8TFT 58.4 58.4 8.3 3.0 3.0 39.8.8 0.3 3/ 3/ / -M0-3TFT 8.2 39.8 24.4 2.7 /

40 Gaugeable Fittings and dapter Fittings Tees Female Branch, NPT (TTF) NPT F, H, H -200-3TTF.94 0.50 0.09 0.75-400-3TTF -400-3-4TTF 2.2 2.34 0.0 0.9 / 0.75 0.88-00-3TTF -00-3-TTF -00-3-8TTF 2.4 2.2 2.84 0. / 3/ 0.88 0.88.2-80-3-4TTF -80-3TTF -80-3-8TTF 2.84 2.84 3.0 0.90 0.4 3/ 3/ 0.88 0.88.2-00-3TTF 3.0 0.9 0.50.2-20-3TTF 3.52 0.9 0.2.25-0-3-2TTF -0-3TTF 3.8 4..23 0.88 /.25.50, mm -M0-3TTF -M0-3-4TTF 53.9 5 5.3 / 9.0.4 8-8M0-3TTF -8M0-3-4TTF 59.7.2.2.4 / 9.0.4 0-0M0-3TTF 7.0 7.2 3/.4 2-2M0-3-4TTF -2M0-3TTF -2M0-3-8TTF 72.0 72.0 77.7.8 3/ 3/.4.4 28.4 -M0-3TTF 77. 24.4 2.7 28.4 Cross Union F,, -200-4.7 0.50 0.09-400-4 2.2 0.0 0.9 5/ -500-4 2.34 0.4 0.25-00-4 2.40 0. -80-4 2.84 0.90 0.4 3/ -20-4 3.4 0.9 0.2 / -0-4 3.8.23 0.88, mm 3-3M0-4 44.7 2.9 2.4 -M0-4 53.9 5.3 8-8M0-4 59.7.2.4 0-0M0-4 7.0 7.2 3/ 2-2M0-4 72.0.8 3/ -M0-4 74.0 24.4 2.7 5/ 8-8M0-4 7. 24.4 5. / 20-20M0-4 89.3 2.0 5.9 -M0-4 89.4 2.0 8.3 25-25M0-4 98.3 3.3 2.8

Sanitary Flange Fittings Gaugeable Fittings and dapter Fittings 4 minimum opening B G C Kwik-Clamp Flange To Swagelok Fitting Flange, (mm) B C F G SS-400-SC-8.57 (39.9) 0.37 (9.4) 0.0 (5.2) 0.9 () 0.98 (24.9) SS-400-SC-2.57 (39.9) 0.2 (5.7) 0.0 (5.2) 0.9 () 0.98 (24.9) SS-400-SC-.57 (39.9) 0.87 (.) 0.0 (5.2) 0.9 () 3/.98 (50.3) SS-400-SC-24.75 (44.4).37 (3) 0.0 (5.2) 0.9 ().98 (50.3) SS-00-SC-8.3 (4.4) 0.37 (9.4) 0. (.8) (7.) 0.98 (24.9) SS-00-SC-2.3 (4.4) 0.2 (5.7) 0. (.8) (7.) 0.98 (24.9) SS-00-SC-.3 (4.4) 0.87 (.) 0. (.8) (7.) 3/.98 (50.3) SS-00-SC-24.72 (43.7).37 (3) 0. (.8) (7.).98 (50.3) SS-80-SC-8.74 (44.2) 0.37 (9.4) 0.90 (.9) 0.37 (9.4) 0.98 (24.9) SS-80-SC-2.74 (44.2) 0.2 (5.7) 0.90 (.9) 0.40 (0.2) 0.98 (24.9) SS-80-SC-.74 (44.2) 0.87 (.) 0.90 (.9) 0.40 (0.2) 3/.98 (50.3) SS-80-SC-24.80 (45.7).37 (3) 0.90 (.9) 0.40 (0.2).98 (50.3) SS-0-SC-.92 (48.8) 0.87 (.).24 (3.5) 0.87 (.).98 (50.3) 2 SS-0-SC-32 2.50 (3.5).87 (47.5).24 (3.5) 0.87 (.) 2 2.52 (4.0)

42 Gaugeable Fittings and dapter Fittings dapters 50 0 5 0 00 0 4 200 50 Solve lignment Problems and Reduce Inventories Swagelok tube adapters can help eliminate difficult alignment problems and reduce inventories. Swagelok tube adapters can be used with any Swagelok tube fittings in this catalog. So, stocking union elbows and union tees in various sizes - BW and materials along with commonly used Swagelok adapters eliminates the need for stocking special elbows and tees. Typical lignment Problem When installing pipe elbows or tees, it is often difficult to align the fitting with the desired run.. In this example, the installation requires connecting tubing to a female end connection. 2. When the pipe connection is tightened, the male elbow points in the wrong direction for the desired run. Loosening the pipe connection could mean leakage at the pipe thread. Swagelok Solution By using a Swagelok tube adapter in conjunction with a union elbow or tee, these difficulties can be avoided. 3. Tighten the pipe connection of a Swagelok male adapter into the female end connection. 4. Connect a Swagelok union elbow or tee to the adapter by tightening the Swagelok tube fitting with a wrench, while holding the elbow or tee in the desired direction. Insert the tubing into the other end of the Swagelok elbow or tee and install the fitting. Swagelok tube adapters are to be used ONLY in Swagelok tube fittings. Use in fittings made by other manufacturers may result in leakage or slippage.

dapters Male Gaugeable Fittings and dapter Fittings 43 /25 mm and under Over /25 mm NPT 3/ 5/ NPT, -2-T--2-2-T--4-3-T--2-3-T--4-4-T--2-4-T--4-4-T-- -4-T--8-5-T--2-5-T--4 --T--2 --T--4 --T-- --T--8-8-T--4-8-T-- -8-T--8 ➀ F..37.9.40.25.4.49.7.29.50.32.53.5.78.75.78 2.00 0.08 0.2 0.7 0.9 0. 0.9 0. 0. 0. 0.37 0.37 7/ 9/ 7/ 9/ 7/ 9/ / 7/ 9/ 7/ 9/ / 9/ / -0-T--8 2.0 0.47-2-T--8-2-T--2 --T--2 --T-- 2.0 2.3 2.0 0.47 0.58 0.2 0.80 / / -20-T--20➁ 3..02-24-T--24➁ 3.72.25 2 2 2-32-T--32➁ 4.70.72 2, mm 8 0 2 28 30 --MT--2 --MT--4-8-MT--4-8-MT-- -0-MT--4-0-MT-- -0-MT--8-2-MT--4-2-MT--8-28-MT--➁ -28-MT--20➁ B-28-MT-- B-28-MT--20-30-MT--➁ -30-MT--20➁ 32.8 38. 39. 39.9 39.9 40. 4.2 4.5 52. 74.7 7.2 8. 70. 79.2 80.0 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. ➁ Furnished with nut and preswaged ferrules. 4. 5. 7. 7. 8.8.2.5.2..2 24.3 2 4 4 9 4 8 35 4 45 4 4 32-32-MT--20➁ 8.0 2.5 4 38-38-MT--24➁ 92.2 3. 55 ISO/BSP Tapered (RT) ISO, -2-T--2RT -2-T--4RT -4-T--2RT -4-T--4RT --T--4RT --T--RT --T--8RT -8-T--4RT -8-T--RT -8-T--8RT ➀ F..37.25.4.53.5.78.75.78 2.00 0.08 0.7 0. 0.37 0.37 7/ 9/ 7/ 9/ 9/ / 9/ / -2-T--2RT 2.0 0.58 / --T--RT 2.0 0.80, mm 0 2 28 --MT--2RT --MT--4RT 32.8 38. 30-30-MT--20RT➁ 80.0 24.3 4 32-32-MT--20RT➁ 8.0 2.5 4 38-38-MT--24RT➁ 92.2 3. 55 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. ➁ Furnished with nut and preswaged ferrules. 4. 8-8-MT--4RT 39. 5. 4-0-MT--4RT -0-MT--RT -2-MT--4RT -2-MT--RT -2-MT--8RT -28-MT--RT➁ -28-MT--20RT➁ B-28-MT--RT B-28-MT--20RT 39.9 40. 4.5 4.2 5.8 74.7 7.2 8. 70. 7. 7. 8.8 8.8.2.5.2. 2 4 4 8 8 35 4 45

44 Gaugeable Fittings and dapter Fittings dapters Male SWGLOK ML TUB PTR ISO PRLLL THRS (RP) CUTWY-MS-0-40 C-PH-0-IM /25 mm and under Over /25 mm ISO/BSP parallel gaskets are available. See page 53. ISO/BSP Parallel (RS) ISO, -2-T--2RS -2-T--4RS -4-T--2RS -4-T--4RS --T--4RS --T--RS -8-T--4RS -8-T--RS -8-T--8RS ➀ F.25.43.35.53.59.2.85.88.9 0.08 0. 0.7 0.23 0. 0.23 0.3 0.37 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. ➁ Furnished with nut and preswaged ferrules. 9/ 9/ / -2-T--2RS 2.20 0.58 5/ --T--RS 2.59 0.80, mm 0 2 8 28 --MT--2RS --MT--4RS 34.3 38.9 4.0 4. 8-8-MT--4RS 39. 5. 9-0-MT--4RS -0-MT--RS -0-MT--8RS -2-MT--4RS -2-MT--RS -2-MT--8RS -8-MT--8RS -8-MT--2RS -28-MT--RS➁ -28-MT--20RS➁ B-28-MT--RS B-28-MT--20RS 40.4 4. 43.2 47.0 47.8 49.8 5.3 55.9 75.4 5.8 9.3 5.9 7. 7. 5.9 8.8.9 3.9 9.8.5 9.8. 4 9 9 9 35 4 50 50 30-30-MT--20RS➁ 79.8 24.3 50 32-32-MT--20RS➁ 80.8 2.5 50 38-38-MT--24RS➁ 9.9 3. 55 ISO/BSP parallel gaskets are available. See page 53. ISO/BSP Parallel (RP) 28 ISO, mm -28-MT--RP➁ -28-MT--20RP➁ B-28-MT--RP B-28-MT--20RP ➀ F 72.7 77.3 5.8 7. 9.8.5 9.8. 4 50 50 30-30-MT--20RP➁ 8. 24.3 50 32-32-MT--20RP➁ 82. 2.5 50 38-38-MT--24RP➁ 94.5 3.8 55 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. ➁ Furnished with nut and preswaged ferrules.

Gaugeable Fittings and dapter Fittings 45 dapters Male O-ring O-ring O-ring /25 mm and under S/MS Straight (ST) Over /25 mm dapts to S J92/ and ISO 92- straight thread boss. S/MS, ➀ F 5/-24-2-T--2ST.20 0.08 7/ 7/-20-4-T--4ST.39 0.7 9/ 7/-20 9/-8-9/-8 - --T--4ST --T--ST --T--8ST -8-T--ST -8-T--8ST.4.52.0.74.82 0.20 0. 0. 0.37 9/ / / -4-0-T--0ST.94 0.47 /-2-2-T--2ST 2.0 0.58 5/-2 --T--ST 2.4 0.80-2 -20-T--20ST➁ 2.8.02-2 -24-T--24ST➁ 3.28.25 2 2 2-2 -32-T--32ST➁ 4.23.72 2 ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. ➁ Furnished with nut and preswaged ferrules. See page 8 for mounting dimensions. O-Seal (S/MS Straight ) S/MS, F 5/-24-2-T--OR.28 0.08 9/ 3/ -24-3-T--OR.38 0.2 7/-20-4-T--OR.54 0.7 5/ -20-5-T--OR.4 0. 9/-8 --T--OR.70 0. 5/ - -8-T--OR.95 0.37 37 N N Flare, ➀ F 7/-20UNJF-3-4-T--4N.4 0.7 7/-20UNJF-3 9/-8UNJF-3 --T--4N --T--N.53.5 0.7 0. ➀ The dimension is the minimum nominal opening. These fittings may have a larger opening at the pipe/straight thread end. -UNJF-3-8-T--8N.9 0.37 3/ /-2UNJ-3-2-T--2N 2.2 0.58 5/-2UNJ-3 --T--N 2.58 0.80

4 Gaugeable Fittings and dapter Fittings dapters Male Pipe Weld 37.5 Pipe Weld J J, -4-T--4W.4 0.7 0.540 --T--8W.4 0. 0.840-8-T--8W -8-T--2W..8 0.37 0.840.050-2-T--2W.87 0.58.050 Wall thickness at weld end is based on schedule 80 pipe. Female /25 mm and under Over /25 mm NPT NPT F, -2-T-7-2 -2-T-7-4.24.39 0.08 9/ 3/ -3-T-7-4.4 0.2-4-T-7-2 -4-T-7-4 -4-T-7- -4-T-7-8.30.4.55.79 0.7 9/ / 5/ -5-T-7-4.48 0. --T-7-2 --T-7-4 --T-7- --T-7-8 -8-T-7-4 -8-T-7- -8-T-7-8.35.50.59.84.7.79 2.05 0. 0.37 9/ / / -0-T-7-8 2.09 0.47 / -2-T-7-8 -2-T-7-2 -2-T-7- --T-7-2 --T-7-2.08 2. 2.30 2.39 2.53 0.58 0.80 / 5/ 5/ -20-T-7-20➀ 3.0.02 2-24-T-7-24➀ 3.50.25 2 2 2-32-T-7-32➀ 4.23.72 2, mm --MT-7-2 --MT-7-4 32.5 37. 4. 4 9 8-8-MT-7-4 37. 5. 9 0 2-0-MT-7-4 -0-MT-7- -0-MT-7-8 -2-MT-7-4 -2-MT-7-8 38. 40. 4.7 43.7 52.3 7. 8.8 9 9 ISO/BSP Tapered (RT) ISO F, -4-T-7-2RT -4-T-7-4RT --T-7-4RT --T-7-RT -8-T-7-4RT -8-T-7-RT -8-T-7-8RT.30.45.50.59.7.80 2.05 0.7 0. 0.37 9/ /, mm --MT-7-2RT 33.0 4. 4 8-8-MT-7-4RT 37. 5. 9 0-0-MT-7-4RT 38. 7. 9 ➀ Furnished with nut and preswaged ferrules.

Gaugeable Fittings and dapter Fittings 47 dapters Female ISO/BSP parallel gaskets and O rings are available. See page 53. ISO/BSP parallel gaskets and O rings are available. See page 53. ISO/BSP Parallel (RP) ISO F, -2-T-7-2RP.7 0.08 9/ -4-T-7-2RP -4-T-7-4RP --T-7-4RP --T-7-RP -8-T-7-RP -8-T-7-8RP, mm --MT-7-2RP --MT-7-4RP.25.50.55.57.78 2.02 32.0 37.8 0.7 0. 0.38 4. 9/ 5/ 5/ / 4 9 2-2-MT-7-8RP 49.8 8.8 ISO/BSP parallel thread (RJ) fittings are available in stainless steel only. ISO/BSP parallel gaskets and O rings are available. See page 53. ISO/BSP Parallel (RG, Gauge) ISO 74, F -4-T-7-4RG.39 0.7 --T-7-RG.55 0.2 5/ -8-T-7-8RG.80 /, mm 8 0 2 --MT-7-4RG --MT-7-RG --MT-7-8RG -8-MT-7-4RG -8-MT-7-RG -8-MT-7-8RG -0-MT-7-4RG -0-MT-7-RG -0-MT-7-8RG -2-MT-7-4RG -2-MT-7-RG -2-MT-7-8RG 35.3 38.4 42.9 33.0 38.9 43.7 34.5 3. 4. 40. 44.7 48.8 4. 5.5 5. 5. 5.5.5 7. 5.5.5 7.0 9 24 9 24 9 24 9 24 --MT-7-8RG 49.0 7.0 8-8-MT-7-8RG 49.3 7.0 ISO/BSP Parallel (RJ) ISO, F SS-4-T-7-4RJ.39 0.7 SS--T-7-RJ.55 0.2 5/ SS-8-T-7-8RJ.94 /, mm 8 0 2 SS--MT-7-4RJ SS--MT-7-RJ SS--MT-7-8RJ SS-8-MT-7-4RJ SS-8-MT-7-RJ SS-8-MT-7-8RJ SS-0-MT-7-4RJ SS-0-MT-7-RJ SS-0-MT-7-8RJ SS-2-MT-7-4RJ SS-2-MT-7-RJ SS-2-MT-7-8RJ 35.3 38. 42.9 33.0 39.4 43.7 34.5 3. 4. 40. 44.7 48.8 4. 5.5 5. 5. 5.5.5 7. 5.5.5 7.0 9 24 9 24 9 24 9 24 N N Flare, -200--2NF -200--4NF F 9/ -400--4NF 9/ -00--NF / -80--8NF -20--2NF

48 Gaugeable Fittings and dapter Fittings dditional Information Swagelok tube fitting ordering numbers follow the sequence shown below. SS - 2 B C0 0 - - 2 F RT G SS - 2 0 0 - - 2 RT Material = luminum B = Brass C20 = lloy 20 HC = lloy C- INC = lloy 00 M = lloy 400 NY = Nylon S = Carbon steel SS = 3 stainless steel T = PTF TI = Titanium 25 = lloy 25 825 = lloy 825 B ( ) Fractional, = / 2 = 3 = 3/ 4 = 5 = 5/ = 8 = 0 = 2 = 4 = = 8 = 20 = 24 = 32 = 2 Metric, mm 2 = 2 3 = 3 4 = 4 = 8 = 8 0 = 0 2 = 2 4 = 4 5 = 5 = 8 = 8 20 = 20 = 25 = 25 28 = 28 32 = 32 38 = 38 50 = 50 C Series 0 = Fractional / to and to 2 = Fractional to M = Millimeter tube size To order a female Swagelok tube fitting, add F. xample: SS-00F--. Component 0 = Fitting = Body Fitting Type = Male connector 2 = 90 male elbow 3 = Tee, union 4 = Cross, union 5 = 45 male elbow = Union 7 = Female connector 8 = Female elbow 9 = lbow, union = Bulkhead male connector = Bulkhead union 7 = Bulkhead female connector = dapter C = Cap P = Plug PC = Port connector R = Reducer R = Bulkhead reducer 2R = Reducing elbow TFT = Tee, female run TMT = Tee, male run TRT = Tee, ISO/BSP parallel male positionable run TST = Tee, straight thread with O ring male positionable run TTF = Tee, female branch TTM = Tee, male branch TTR = Tee, ISO/BSP parallel male positionable branch TTS = Tee, straight thread with O ring male positionable branch F Second nd Connection dd a size designator from the list at left for the second end connection or if the fitting is a reducing union. G Second nd Connection Type dd a second end connection type designator as needed. N = 37 male N flare NF = 37 female N flare BT = Bored-through fitting F = Female thread KN = Knurled nut, nylon ferrules KT = Knurled nut, PTF ferrules M = Metric tube end OR = O-seal connection PR = ISO/BSP positionable parallel pipe thread RG = ISO/BSP parallel pipe thread (gauge) RJ = ISO/BSP parallel pipe thread (Japanese gauge) RP = ISO/BSP parallel pipe thread RS = ISO/BSP parallel pipe thread RT = ISO/BSP tapered pipe thread ST = Straight thread with O-ring (for S/MS) W = Male pipe weld/tube socket weld Tees and Crosses numbers for tees and crosses indicate first the size of the run ( to 2) and then the size of the branch (3 for tees and 3 to 4 for crosses). xample: SS-M0-3-4TTF for a 3 SS female tee for mm tube with female NPT branch 4 2 3 dditional s and Materials Contact your authorized Swagelok representative for information about additional sizes and special alloys.

dditional Information Swagelok tube adapter ordering numbers follow the sequence shown below. SS - B2 - T C - - 4 RT F SS - 2 - T - - 4 RT Gaugeable Fittings and dapter Fittings 49 Material = luminum B = Brass C20 = lloy 20 HC = lloy C- INC = lloy 00 M = lloy 400 NY = Nylon S = Carbon steel SS = 3 stainless steel T = PTF TI = Titanium 25 = lloy 25 825 = lloy 825 B ( ) Fractional, = / 2 = 3 = 3/ 4 = 5 = 5/ = 8 = 0 = 2 = 4 = = 8 = 20 = 24 = 32 = 2 Metric, mm 2 = 2 3 = 3 4 = 4 = 8 = 8 0 = 0 2 = 2 4 = 4 5 = 5 = 8 = 8 20 = 20 = 25 = 25 28 = 28 32 = 32 38 = 38 50 = 50 C Component T = Fractional tube adapter MT = Metric tube adapter dapter Type = Male adapter 7 = Female adapter Second nd Connection dd a size designator from the list at left for the second end connection. F Second nd Connection Type dd a second end connection type designator as needed. N = 37 male N flare NF = 37 female N flare RG = ISO/BSP parallel pipe thread (gauge) RJ = ISO/BSP parallel pipe thread (Japanese gauge) RP = ISO/BSP parallel pipe thread RS = ISO/BSP parallel pipe thread RT = ISO/BSP tapered pipe thread ST = Straight thread with O-ring (for S/MS) W = Male pipe weld/tube socket weld

50 Gaugeable Fittings and dapter Fittings Replacement Parts To order, add a material designator from the How to Order table on page 0. Nuts L G flat Female G L, / -02-5/ 0.3-202- 7/ 0.47 3/ -302-0.47-402- 9/ 0.50 5/ -502-0.53-02- / 0.5-82- 0.9-02- 0.9 -- 0.9-42- 0.9-2- 0.8-2002-.25-2402- 2.50 2-3202- 3 2.0 G L, mm 2-2M2-2.9 3-3M2-2.9 4-4M2-2.9 -M2-4 2.7 8-8M2-3.5 0-0M2-9 5. 2-2M2-7.4 4-4M2-25 7.4 5-5M2-25 7.4 -M2-25 7.4 8-8M2-30 7.4 20-20M2-32 7.4 -M2-32 7.4 25-25M2-38 20. 28-28M2-4 30. B-28M2-45 20. 30-30M2-50 32.7 32-32M2-50 34.4 38-38M2-0 40. 50-50M2-3 52.3 G flat L Knurled Female The Swagelok knurled nut tube fitting provides a leak-tight seal without the use of inserts on most wall thicknesses of polyethylene tubing. Inserts may be required for larger sizes. To set the ferrules on the tubing, initial connections must be made with a wrench, tightening the nut one and one-quarter turns from finger-tight (threequarter turn for /, and 3/ ; 2, 3, and 4 mm fittings). Leak-tight connections may be reassembled with finger-tight assembly. To order a knurled nut, add K to the female nut basic ordering number. xample: B-402-K To order a knurled nut on an assembled fitting with nylon ferrules, add KN to the fitting ordering number. xample: SS-400--2KN To order a knurled nut on an assembled fitting with PTF ferrules, add KT to the fitting ordering number. xample: SS-400--2KT G flat L For use in female Swagelok end connections. Male G L, / -F2-GC 0.38-2F2-GC 0.53-4F2-0.2-8F2-5/ 0.87 G L, mm 0-0MF2-. 2-2MF2-24.

Replacement Parts SWGLOK FRONT FRRUL CUTWY-MS-0-40 C-PH-005-BM To order, add a material designator from the How to Order table on page 0. SWGLOK BCK FRRUL CUTWY-MS-0-40 C-PH-005-M Ferrules Gaugeable Fittings and dapter Fittings 5 Front Back, / -03- -203-3/ -303- -403-5/ -503- -03- -83- -03- -23- -43- -3- -2003-➀ -2403-➀ 2-3203-➀ ➀ Over and over 25 mm stainless steel front ferrules are PF coated. To order silverplated front ferrules, add -BL to the basic ordering number. xample: SS-2003--BL, mm 2-2M3-3 -3M3-4 -4M3- -M3-8 -8M3-0 -0M3-2 -2M3-4 -4M3-5 -5M3- -M3-8 -8M3-20 -20M3- -M3-25 -25M3-28 -28M3-➀ 30-30M3-➀ 32-32M3-➀ 38-38M3-➀ 50-50M3-➀, / -04- -204-3/ -304- -404-5/ -504- -04- -84- -04- -24- -44- -4- -2004-➀ -2404-➀ 2-3204-➀ ➀ Over and over 25 mm stainless steel back ferrules are PF coated. To order back ferrules without PF coating, add -WC to the basic ordering number. xample: SS-2004--WC, mm 2-2M4-3 -3M4-4 -4M4- -M4-8 -8M4-0 -0M4-2 -2M4-4 -4M4-5 -5M4- -M4-8 -8M4-20 -20M4- -M4-25 -25M4-28 -28M4-➀ 30-30M4-➀ 32-32M4-➀ 38-38M4-➀ 50-50M4-➀

52 Gaugeable Fittings and dapter Fittings Replacement Parts Nut-Ferrule Set and Ferrule Set Use of Nuts and Ferrules Using Swagelok nuts and ferrules on tube fittings or valves with tube end connections requires critical interaction of precision parts. Swagelok nuts and ferrules are sold as replacement parts for use with only Swagelok bodies, fittings, valves, and hose products. Sets are shown with arbors. One arbor holds five nut-ferrule sets or ten ferrule sets. Nut-Ferrule Set Ferrule Set The nut-ferrule set contains one nut, one back ferrule, and one front ferrule. To order, add a material designator to the basic ordering number. Please order nut-ferrule sets in multiples of five. xample: SS-400-NFST The ferrule set contains one front ferrule and one back ferrule. To order, add a material designator to the basic ordering number. Please order ferrule sets in multiples of ten. xample: SS-00-ST Material Brass Carbon steel 3 stainless steel esignator B S SS, -400-NFST -00-NFST -80-NFST, mm -M0-NFST 8-8M0-NFST 0-0M0-NFST 2-2M0-NFST Material lloy 400 luminum Brass Carbon steel Nylon PTF 3 stainless steel Nut-Ferrule Package and Ferrule-Pak Package To order the nut-ferrule package (50 nut-ferrule sets) or ferrule-pak package (00 front and back sets), contact your authorized Swagelok sales and service representative. esignator M B S NY T SS, / -00-ST -200-ST 3/ -300-ST -400-ST 5/ -500-ST -00-ST -80-ST, mm -M0-ST 8-8M0-ST 0-0M0-ST 2-2M0-ST Nut-Ferrule Package Ferrule-Pak Package

Gaugeable Fittings and dapter Fittings 53 Replacement Parts ISO/BSP Parallel Gaskets RS/RS Gasket RSNB Gasket Steel and Stainless Steel (RS Fitting) RS fitting steel Gasket gaskets provide a seal with male ISO/BSP parallel threads. The RS gasket is of a fluorocarbon FKM inner ring bonded to a carbon steel outer ring. The RS (IN-style) gasket is a fluorocarbon FKM inner ring bonded to a stainless steel or carbon steel outer ring as recommended in ISO 79-973. It can be used with end connections designed in accordance with IN 3852 Part 2. The RSNB gasket is an all-metal 304L stainless steel gasket similar to IN 703 form. ISO, RS Gasket➀ RS Gasket➁ RSNB Gasket S-2-RS-2V SS-2-RS-2V 304L-2-RSNB-2 S-4-RS-2V➂ SS-4-RS-2V 304L-4-RSNB-2 S--RS-2V➂ SS--RS-2V 304L--RSNB-2 S-8-RS-2V➂ SS-8-RS-2V 304L-8-RSNB-2 S-2-RS-2V SS-2-RS-2V 304L-2-RSNB-2 S--RS-2V SS--RS-2V 304L--RSNB-2 S-20-RS-2V SS-20-RS-2V 304L-20-RSNB-2 S-24-RS-2V SS-24-RS-2V 304L-24-RSNB-2 ➀ lso available with a Buna inner ring. To order, replace V with B in the ordering number. xample: S-2-RS-2B ➁ lso available with a carbon steel outer ring. To order, replace SS with S in the ordering number. xample: S-8-RS-2V ➂ lso available with a stainless steel outer ring. To order, replace S with SS in the ordering number. xample: SS-8-RS-2V Copper (RP and RS Fitting) The RP and RS fitting copper gasket provides a seal with male ISO/BSP parallel threads. Gasket ISO, CU-2-RP-2 CU-4-RP-2 CU--RP-2 CU-8-RP-2 CU-2-RP-2 CU--RP-2 CU-20-RP-2 CU-24-RP-2 Copper and Nickel (RG, Gauge Fitting) The RG fitting gasket provides a seal on pressure gauges equipped with ISO/BSP parallel male threads. ISO, Copper Nickel CU-4-RG-2 NI-4-RG-2 CU--RG-2 NI--RG-2 CU-8-RG-2 NI-8-RG-2 Gasket PTF (RJ Fitting) The RJ fitting PTF gasket provides a seal with ISO/BSP parallel male threads. ISO, Regular Gaskets T-4-RJ-2 T--RJ-2 T-8-RJ-2 Thick Gaskets T-4-RJ-2-T T--RJ-2-T T-8-RJ-2-T Contact your authorized Swagelok representative for gasket dimensions.

54 Gaugeable Fittings and dapter Fittings Replacement Parts O-Rings Buna N (O-Seal Straight s) O-ring hardness is 70 durometer. Buna N (O-Seal Pipe s) O-ring hardness is 70 durometer. Uniform 5/-24 0 BN-70-OR-0-24 02 BN-70-OR-02 7/-20 03 BN-70-OR-03-20 2 BN-70-OR-2 9/-8 3 BN-70-OR-3 - BN-70-OR- /-2 2 BN-70-OR-2 5/-2 25 BN-70-OR-25 NPT/ISO Pipe Uniform 03 BN-70-OR-03 3 BN-70-OR-3 BN-70-OR- 8 BN-70-OR-8 Fluorocarbon FKM (Positionable Fittings, ISO/BSP Parallel s) O-ring hardness is 90 durometer. ISO Uniform 502➀ FSP-90-OR-502 FCBR-90-OR- 3 FCBR-90-OR-3 508➀ FCBR-90-OR-508 9 FCBR-90-OR-9 FCBR-90-OR- ➀ Not a uniform O-ring size. Fluorocarbon FKM (S/MS Straight s) O-ring hardness is 90 durometer. S/MS Uniform 5/-24 902 FCBR-90-OR-902-24 903 FCBR-90-OR-903 7/-20 904 FCBR-90-OR-904-20 905 FCBR-90-OR-905 9/-8 90 FCBR-90-OR-90-908 FCBR-90-OR-908-4 90 FCBR-90-OR-90 /-2 92 FCBR-90-OR-92 3/-2 94 FCBR-90-OR-94 5/-2 9 FCBR-90-OR-9-2 920 FCBR-90-OR-920-2 924 FCBR-90-OR-924 2-2 932 FCBR-90-OR-932

Gaugeable Fittings and dapter Fittings 55 Tools and ccessories Hydraulic Swaging Units Swagelok hydraulic swaging units preswage Swagelok ferrules onto tubing prior to assembly and provide Swagelok tube fitting connections that are 00 % gaugeable upon initial installation. Multihead hydraulic and air-actuated hydraulic swaging units: Place no initial strain on nut or fitting body threads or on body seal surfaces re available with interchangeable fractional and metric tooling Fit neatly in a rugged plastic carrying case Reduce assembly and installation time and operator error. Multihead Hydraulic Swaging Unit (MHSU) Is available in two unit sizes, with tooling for: to and 2 to 25 mm tubing and tube adapters to 2 and 25 to 50 mm tubing and tube adapters Must be used to install,, and 2 and 28, 30, 32, 38, and 50 mm Swagelok tube fittings Is standard with a tube marking feature to indicate when tube is properly bottomed in the unit Is available with a support base (as shown). See Information, page 5. Is available with stainless steel connection tubing in place of hydraulic hose; support base is required. See Information, page 5. The MHSU cannot be used for SF 2507 tubing and under or for medium-pressure tubing. For and SF 2507 tubing, order the /25 mm and over unit and SF 2507 tooling kit and gap inspection gauges. Recommended Minimum Wall Thickness of Tubing for use with the MHSU Tooling Steel Stainless Steel Tubing Wall, 0.049 0.05 0.05 0.083 0.083 0.095 2 0.095 0.09 Use of tubing below the recommended minimum wall thickness may result in the tube sticking in the die head. MHSU Unit Components Multihead hydraulic swaging unit Hydraulic hose 2 ft (0. m) with all units except /25 mm and over unit without support base, which contains ft (.8 m) hose Retaining ring pliers Safety glasses Operating instructions Carrying case Tooling 2 4 5 8 20 25 28 30 32 38 50 Steel Stainless Steel Tubing Wall, mm.5.5.8 2.0 2.0 2.2 2.2 2.5 Tooling Kit Components ie head sets for Swagelok tube fitting sizes: Fractional, up to,,,, and Fractional, and over,,, and 2 Metric, up to 25 mm 2, 4, 5,, 8, 20,, and 25 mm Metric, 25 mm and over 25, 28, 30, 32, and 38 mm 50 mm tooling available separately Gap inspection gauges Chamfer block (up to /25 mm sizes only) Technical ata MHSU case (55.9 cm) high, 24 (.0 cm) wide, 8.75 (.2 cm) deep Weight Up to /25 mm MHSU in case with tooling kit and support base 40 lb (8. kg) /25 mm and over MHSU in case with tooling kit and support base 55 lb (24.9 kg) Construction High-strength stainless steel tooling for durability and corrosion resistance See next page for Information.

5 Gaugeable Fittings and dapter Fittings Tools and ccessories Hydraulic Swaging Units MHSU Information Select an ordering number. s MHSU Unit Up to / MS-MHSU-U- 25 mm sizes /25 mm MS-MHSU-O- and over sizes MHSU Unit with Tooling Kit Fractional up to sizes MS-MHSU-U--FKIT-M Fractional MS-MHSU-O--FKIT-M and over sizes Metric up to MS-MHSU-U--MKIT-M 25 mm sizes Metric 25 to 38 mm➀ sizes MS-MHSU-O--MKIT-M ➀ 50 mm tooling available separately. Support Base dd -B to the ordering number. xamples: MS-MHSU-U--B MS-MHSU-U--FKIT-M-B Stainless Steel Connection Tubing dd -T to the ordering number for an MHSU with support base. xamples: MS-MHSU-U--B-T MS-MHSU-U--FKIT-M-B-T Operating Instructions MHSU ordering numbers include nglish-language instructions. For other languages, visit swagelok.com. ccessories dditional and replacement gap inspection gauges are available. See page 59. See the table below for replacement retaining rings and pliers. MHSU Unit Retaining Ring Up to / MS-MHSU-N5000-200-H 25 mm sizes /25 mm and over sizes MS-MHSU-N5000-35-H Retaining Ring Pliers Up to / MS-MHSU-0504 25 mm sizes /25 mm and over sizes MS-MHSU-0700 Tooling Kits Up to /25 mm /25 mm and Over, MS-MHSUT-U-80-M MS-MHSUT-U-00-M MS-MHSUT-U-20-M MS-MHSUT-U-40-M MS-MHSUT-U-0-M SF 2507 Tubing MS-MHSUT-O-2507-00-M MS-MHSUT-O-2507-20-M, mm 2 MS-MHSUT-U-2M0-M 4 MS-MHSUT-U-4M0-M 5 MS-MHSUT-U-5M0-M MS-MHSUT-U-M0-M 8 MS-MHSUT-U-8M0-M 20 MS-MHSUT-U-20M0-M MS-MHSUT-U-M0-M 25 MS-MHSUT-U-25M0-M, MS-MHSUT-O-0-M MS-MHSUT-O-2000-M MS-MHSUT-O-2400-M 2 MS-MHSUT-O-3200-M, mm 25 MS-MHSUT-O-25M0-M 28 MS-MHSUT-O-28M0-M 30 MS-MHSUT-O-30M0-M 32 MS-MHSUT-O-32M0-M 38 MS-MHSUT-O-38M0-M 50 MS-MHSUT-O-50M0-M See the Swagelok Multihead Hydraulic Swaging Unit (MHSU) Setup and Operating Instructions, MS 2 37, for information about using the MHSU. ir-ctuated Hydraulic Swaging Unit (HSU) Requires only one unit with interchangeable tooling to swage to and to 2 mm Swagelok tube fitting ferrule sizes Requires no threading of nut on or off the tooling The HSU cannot be used for SF 2507 tubing or for mediumpressure tubing. HSU Unit Components ir-actuated hydraulic swaging unit Hex key dapter plates for tube fittings smaller than or 2 mm Safety glasses Gap inspection gauges Operating instructions Carrying case Tooling Kit Components ie head sets and gap inspection gauges for Swagelok tube fitting sizes: Fractional,, and Metric, 8, 0, and 2 mm Technical ata HSU case 9 (48.3 cm) high, 5.5 (39.4 cm) wide, 7.5 (9.0 cm) deep Weight HSU in case with tooling kit 28 lb (2.7 kg) Power requirements 20 to 70 psig (.4 to bar) regulated shop air, depending on fitting size and material Construction High-strength stainless steel tooling for durability and corrosion resistance ir inlet port Swagelok tube fitting

Gaugeable Fittings and dapter Fittings 57 Tools and ccessories Hydraulic Swaging Units HSU Information Select an ordering number. HSU only s HSU Unit MS-HSU- HSU Unit with Tooling Kit,, sizes, 8, 0, 2 mm sizes MS-HSU--FKIT MS-HSU--MKIT Preswaging Tools For Swagelok tube fitting installations in close quarters, the Swagelok preswaging tool is a convenient accessory. Features Preswages ferrules onto the tube nables the installer to work in a more open, safe area Makes it possible to complete the installation by following retightening instructions for Swagelok tube fittings. Tooling Kits, MS-HSUT-400- MS-HSUT-00- MS-HSUT-80-, mm MS-HSUT-M0-8 MS-HSUT-8M0-0 MS-HSUT-0M0-2 MS-HSUT-2M0- Operating Instructions HSU ordering numbers include nglish-language instructions. For other languages, visit swagelok.com. ccessories dditional and replacement gap inspection gauges are available. See page 59. See the Swagelok ir-ctuated Hydraulic Swaging Unit (HSU) Setup and Operating Instructions, MS 2 38, for information about using the HSU. High-Volume Swaging Unit (HVSU) The Swagelok high-volume swaging unit (HVSU) is designed to easily preswage a Swagelok nut and ferrules onto stainless steel tubing. The pneumatically driven and electronically controlled semiautomatic unit uses sensors to start and stop the process for consistent preswaging results. For more information, see the Swagelok High-Volume Swaging Unit catalog, MS 02 44., Female Nut / MS-ST-00 MS-ST-200 3/ MS-ST-300 MS-ST-400 5/ MS-ST-500 MS-ST-00 MS-ST-80 ➀ MS-ST-00 (SF 2507) MS-ST-2507-00 ➀ MS-ST-20 (SF 2507) MS-ST-2507-20 MS-ST-40 MS-ST-0 Male Nut / MS-ST-F0 (mediumpressure) MS-ST-4FK0 (mediumpressure) MS-ST-FK0 ➁ MS-ST-8F0 (mediumpressure) MS-ST-8FK0 ➀ For SF 2507 tubing, use the preswaging tool for the appropriate tube and with 2507 in the ordering number. ➁ For medium-pressure tubing, use the preswaging tool for the appropriate tube and with FK0 in the ordering number., mm Female Nut 3 MS-ST-3M0 4 MS-ST-4M0 MS-ST-M0 8 MS-ST-8M0 0 MS-ST-0M0 2 MS-ST-2M0 4 MS-ST-4M0 5 MS-ST-5M0 MS-ST-M0 8 MS-ST-8M0 20 MS-ST-20M0 MS-ST-M0 25 MS-ST-25M0

58 Gaugeable Fittings and dapter Fittings Tools and ccessories Wrenches Tee Wrench The tee wrench provides positive backup support when installing Swagelok union tees and crosses. Ratchet Wrench The ratchet wrench is designed for use on Swagelok nuts for fitting installation. Features llows user to hold fitting body firmly and precisely Is available in a variety of sizes Fits and carries easily in tool box, pouch, or belt Head and handle constructed of stainless steel Features a cushioned vinyl grip and generous gripping area for handle Holds tee in various orientations Information For Swagelok Gaugeable Union Tees and Crosses Tee Cross and mm MS-TW-4 5/ and and 8 mm MS-TW- 0 mm MS-TW-0M ➀ and 2 mm MS-TW-8 ➀ Use MS-TW-8 on 0 mm Swagelok crosses. Features fractional and metric sizes are available. /2 turn ratchet facilitates use in close quarters. Heavy-duty construction includes: heat-treated, black oxide-plated steel handle black-oxide plated steel jaws stainless steel spring and fasteners. Information, MS-RW-200 3/ MS-RW-300 MS-RW-400 5/ MS-RW-500 MS-RW-00 Wrench Length 5.38 7.25 MS-RW-80 0., mm 3 MS-RW-3M0 3 MS-RW-M0 8 MS-RW-8M0 0 MS-RW-0M0 84 2 MS-RW-2M0 257 Ratchet Wrench Pouch heavy-duty pouch is available for holding up to six Swagelok ratchet wrenches. : MS-RWP

Gaugeable Fittings and dapter Fittings 59 Tools and ccessories Gap Inspection Gauges Swagelok gap inspection gauges assure the installer or inspector that the fitting has been sufficiently pulled up on initial installation, whether using a Swagelok multihead hydraulic swaging unit (MHSU), page 55, or air-actuated hydraulic swaging unit (HSU), page 5, or wrench tightening. ll metal Swagelok tube fittings are gaugeable, with the exception of a few forged bodies in aluminum. For Installation Using the HSU Fitting mm Female Nut,, MS-HSU-IG-48, 8, 0, 2 MS-HSU-IG-2M For Installation Using the MHSU Fitting mm Female Nut ➀ 2 MS-MHSU-IG-80 ➁ 4, 5, MS-MHSU-IG-00 (SF 2507) MS-MHSU-IG-2507-00 ➁ 8 MS-MHSU-IG-20 (SF 2507) MS-MHSU-IG-2507-20 20, MS-MHSU-IG-40 25 MS-MHSU-IG-0-28 MS-MHSU-IG-28M0-30 MS-MHSU-IG-30M0- MS-MHSU-IG-2000-2 32 MS-MHSU-IG-32M0-38 MS-MHSU-IG-38M0- MS-MHSU-IG-2400-50 MS-MHSU-IG-50M0-2 MS-MHSU-IG-3200- ➀ The MHSU cannot be used for SF 2507 tubing and under or for medium-pressure tubing. ➁ For and SF 2507 tubing, order the (25 mm) and over unit and SF 2507 tooling and gauge. For Installation Using a Wrench Fitting mm Female Nut / MS-IG-00 2, 3 MS-IG-200 3/ 4 MS-IG-300 MS-IG-400,,, 2 MS-IG-48,, 8, 0, 2 MS-IG-2M 5/ 8 MS-IG-500 MS-IG-00 0 MS-IG-0M0 2 MS-IG-80 4, 5, MS-IG-00 (SF 2507) MS-IG-2507-00 8 MS-IG-20 (SF 2507) MS-IG-2507-20 20, MS-IG-40 25 MS-IG-0 Male Nut / MS-IG-F0 2, 3 MS-IG-2F0,, (mediumpressure) MS-IG-FK0 epth Marking Tools Swagelok depth marking tools help ensure that tubing is bottomed on the shoulder inside the Swagelok tube fitting body., MS-MT-400 MS-MT-00 MS-MT-80 MS-MT-00 MS-MT-20 MS-MT-40 MS-MT-0, mm MS-MT-M0 8 MS-MT-8M0 0 MS-MT-0M0 2 MS-MT-2M0 MS-MT-M0 8 MS-MT-8M0

0 Gaugeable Fittings and dapter Fittings Tools and ccessories Bulkhead Retainers By using the bulkhead retainer, one person can tighten the jam nut on side for initial bulkhead fitting installation. Now tubing can be connected to side and B by one person with one wrench, because the bulkhead retainer acts as a backup wrench. F "U" drive screw (included) B Side Jam nut U drive screw Bulkhead retainer Body hex Side B Bulkhead fitting installation utilizing bulkhead retainer, U Fitting rill rive Hole Screw rill mm B F ia / SS-02-F 5/ 5/ 5/32 SS-202-F 3/32 7/32 3/ 3, 4 SS-302-F 9/ 9/ 5/32 SS-402-F 9/32 5/32 0.20-3 5/ SS-502-F / / 9/ 5/ 8 SS-8M2-F / 8 mm 9/ 5/ SS-02-F /32 0 SS-0M2-F 5/ mm 3/32 2 SS-82-F 5/ 5/ 3/32 5, SS-02-F / 3/ 3/32 8 SS--F / 3/ 29/32 5/32 7/32 0.44 0- SS-42-F 5/ /32 7/32 SS-2-F 9/32 5/32 9/ Inserts for Soft Plastic Tubing I Information dd the insert material designator to the basic ordering number. xample: B-305-2 I of bore Swagelok inserts help secure soft plastic tubing being used with standard Swagelok tube fittings. To determine the correct size of the Swagelok insert to be used, check both outside diameter and inside diameter of the plastic tubing. For a complete line of hose connectors for soft plastic tubing, see the Swagelok Hose and Flexible Tubing catalog, MS 0 80. Material lloy 400 luminum Brass Carbon steel Nylon Stainless steel esignator M B S NY SS I Bore I, 3/ 0.09-305-2 0.09-405-2 0.7 0. -405-70 3/ 0.4-405-3 0.09-505-2 5/ 3/ 0.2-505-3 0.9-505-4 3/ 0.2-05-3 0.9-05-4 0.9-85-4 0.3-85- 0.3-05- 0.44-05-8 0.44-25-8 0.5-25-0 0.9-5-2, mm 4 2.8 -M5-4M 8 4.4-8M5-M 0 8.4-0M5-8M 2 8.4-2M5-8M 0 8.3-2M5-0M

Gaugeable Fittings and dapter Fittings Gaugeability On initial installation, the Swagelok gap inspection gauge assures the installer or inspector that a fitting has been sufficiently tightened. Position the Swagelok gap inspection gauge next to the gap between the nut and body. If the gauge will not enter the gap, the fitting is sufficiently tightened. If the gauge will enter the gap, additional tightening is required. lways depressurize a system before adjusting the tightness of a tube fitting connection. Installation Instructions Swagelok tube fittings /25 mm and smaller can be installed quickly, easily, and reliably with simple hand tools. Over /25 mm sizes require use of a hydraulic swaging unit to swage the ferrules onto the tubing. Safety Precautions o not bleed system by loosening fitting nut or fitting plug. o not assemble or tighten fittings when system is pressurized. Make sure that the tubing rests firmly on the shoulder of the tube fitting body before tightening the nut. Use the correct Swagelok gap inspection gauge to ensure sufficient pull-up upon initial installation. lways use proper thread sealants on tapered pipe threads. o not mix materials or fitting components from various manufacturers tubing, ferrules, nuts, and fitting bodies. Never turn fitting body. Instead, hold fitting body and turn nut. void unnecessary disassembly of unused fittings. Use only long reducers in female Swagelok end connections. See the instructions starting on the next page for installation of Swagelok tube fittings, O-seal male connectors, caps and plugs, port connectors, tube adapters, positionable elbows and tees, weld fittings, depth marking tool, and preswaging tool. Tubing Considerations Metal tubing material should be softer than fitting material. For example, stainless steel tubing should not be used with brass fittings. When tubing and fittings are made of the same material, tubing must be fully annealed. lways use an insert with extremely soft or pliable plastic tubing. xtremes of wall thickness should always be checked against the suggested minimum and maximum wall thickness limitations. Surface finish is very important to proper sealing. Tubing with any kind of depression, scratch, raised portion, or other surface defect will be difficult to seal, particularly in gas service. Tubing that is oval and will not easily fit through fitting nuts, ferrules, and bodies should never be forced into the fitting. See Swagelok Tubing ata, MS-0-07, for more information about tubing selection.

2 Gaugeable Fittings and dapter Fittings Installation Instructions Swagelok Fittings Up to /25 mm These instructions apply both to traditional fittings and to fittings with the advanced back-ferrule geometry. Fully insert the tube into the fitting and against the shoulder; rotate the nut finger-tight. High-pressure applications and high safety-factor systems: Further tighten the nut until the tube will not turn by hand or move axially in the fitting. Mark the nut at the o clock position. While holding the fitting body steady, tighten the nut one and one-quarter turns to the 9 o clock position. For /,, and 3/ ; 2, 3, and 4 mm tube fittings, tighten the nut only three-quarters turn to the 3 o clock position. Swagelok Fittings Over /25 mm. Preswage the ferrules onto the tube using a Swagelok multihead hydraulic swaging unit (MHSU). 2. pply the lubricant packaged with the fitting lightly to the body threads and the rear surface of the back ferrule. 3. Insert the tube with preswaged ferrules into the fitting until the front ferrule seats against the fitting body; rotate the nut finger-tight. 4. Mark the nut at the o clock position. 5. While holding the fitting body steady, tighten the nut one-half turn to the 2 o clock position. Use the Swagelok MHSU gap inspection gauge to ensure that the fitting has been tightened sufficiently. Reassembly ll s You may disassemble and reassemble Swagelok tube fittings many times. lways depressurize the system before disassembling a Swagelok tube fitting. Prior to disassembly, mark the tube at the back of the nut; mark a line along the nut and fitting body flats. Use these marks to ensure that you return the nut to the previously pulledup position. Insert the tube with preswaged ferrules into the fitting until the front ferrule seats against the fitting body. Over /25 mm sizes: If needed, reapply lubricant lightly to the body threads and the rear surface of the back ferrule. While holding the fitting body steady, rotate the nut with a wrench to the previously pulled-up position, as indicated by the marks on the tube and flats. t this point, you will feel a significant increase in resistance. Tighten the nut slightly. o not use the Swagelok gap inspection gauge with reassembled fittings. O-Seal Male Connectors. Turn the O-seal connector into the female end until it is finger-tight. 2. Tighten the O-seal connector until it makes metal-to-metal contact with the face of the female end. 3. Tighten slightly with a wrench.

SWGLOK SWGLOK SWGLOK SWGLOK Installation Instructions Caps and Plugs Caps See Swagelok tube fitting installation and reassembly, page 2. Gaugeable Fittings and dapter Fittings 3 Plugs While holding fitting body steady, tighten the plug one-quarter turn from the finger-tight position. For /,, and 3/ ; 2, 3, and 4 mm tube fittings, tighten the plug one-eighth turn. For over /25 mm tube fittings, tighten the plug one-quarter turn. o not use the Swagelok gap inspection gauge with plug assemblies. Reassembly You may disassemble and reassemble Swagelok plugs many times. Make subsequent connections by slightly tightening with a wrench after snugging the nut by hand. Port Connectors Connect the machined ferrule end before connecting the tube adapter end. Machined Ferrule nd dapter nd. Remove the nut and ferrules from the Swagelok end connection. iscard the ferrules. 5. Insert the tube adapter until it rests firmly on the shoulder of the Swagelok tube fitting body. Finger-tighten the nut. SWGLOK iscard 2. Slip the nut over the machined ferrule end of the port connector. Over /25 mm sizes: The nut is preassembled on the port connector. 3. Insert the port connector into the end connection and finger-tighten the nut. 4. While holding fitting body steady, tighten the nut one-quarter turn. For /,, and 3/ ; 2, 3, and 4 mm tube fittings, tighten the nut one-eighth turn. o not use the Swagelok gap inspection gauge with machined ferrule ends. Reassembly You may disassemble and reassemble Swagelok port connectors many times. Make subsequent connections by slightly tightening with a wrench after snugging the nut by hand. SWGLOK SWGLOK SWGLOK SWGLOK /25 mm and under SWGLOK Over /25 mm Over /25 mm sizes: Remove and discard the nut and ferrules from the end connection, then insert the tube adapter.. Mark the nut at the o clock position. While holding fitting body steady, tighten the nut one and one-quarter turns to the 9 o clock position. For /,, and 3/ ; 2, 3, and 4 mm tube fittings, tighten the nut three-quarters turn to the 3 o clock position. For preswaged over /25 mm and over tube fittings, tighten the nut one-half turn to the 2 o clock position. o not use the Swagelok gap inspection gauge with preswaged tube adapter connections over /25 mm. Reassembly See Swagelok tube fitting reassembly, page 2. 9 2 3

4 Gaugeable Fittings and dapter Fittings Installation Instructions Positionable lbows and Tees Lock nut Backup washer. Turn the positionable end into the female fitting until the metal backup washer contacts the face of the fitting. 2. Turn the positionable end out of the female fitting (not more than one turn) until the Swagelok tube fitting end is positioned properly. 3. While holding fitting body steady, tighten the lock nut until the metal backup washer contacts the face of the fitting. dapters Fig. Fig. 2 Female pipe port on existing equipment Up to /25 mm. Install the end opposite the tube adapter end (Fig. ). 2. Insert the tube adapter into the Swagelok tube fitting. Make sure that the tube adapter rests firmly on the shoulder of the tube fitting body and that the nut is finger-tight (Fig. 2). 3. Mark the nut at the o clock position. 4. While holding fitting body steady, tighten the nut one and onequarter turns to the 9 o clock position. For /,, and 3/ ; 2, 3, and 4 mm tube fittings, tighten the nut only three-quarters turn to the 3 o clock position. Over /25 mm Swagelok tube adapters over / 25 mm are furnished with nuts and preswaged ferrules. To assemble, follow steps 2 through 5 of the Swagelok tube fittings over /25 mm assembly instructions, page 2. o not use the Swagelok gap inspection gauge with preswaged tube adapter connections over /25 mm. Reassembly See Swagelok tube fitting reassembly, page 2. Weld Fittings Welding Precautions for Swagelok Fittings with Weld nd Connections. Remove the nut and ferrules. 5. Complete the weld. 2. Turn a Swagelok tube fitting plug or another nut onto the. Remove the plug or nut and replace the nut and ferrules. fitting so that it is finger-tight. This protects the threads and sealing components. 3. Provide a suitable heat sink to dissipate the heat. 4. Tack weld at four positions 90 apart to hold the fitting in place and to ensure alignment and concentricity of the components. Caution: When welding carbon steel fittings, the heat often removes the protective oil from the threads. It is important to apply another lubricant, such as Goop thread lubricant. epth Marking Tool Fig. Fig. 2. Insert cleanly cut, fully deburred tube into the depth marking tool (MT) until the tube is against the shoulder of the tool. Using a pen or pencil, mark the tube at the top of the MT (Fig. ). 2. Remove the tube from the MT and insert it into the Swagelok fitting until it is against the shoulder of the fitting body (Fig. 2). Rotate the nut finger-tight. If any portion of the mark on the tube can be seen above the fitting nut, the tube is not fully inserted into the fitting. 3. While holding the fitting body steady, follow Swagelok tube fitting installation instructions, page 2.

Gaugeable Fittings and dapter Fittings 5 Installation Instructions Preswaging Tool Fig. Fig. 2 Fig. 3. Install the Swagelok nut and ferrules onto the preswaging tool. 2. Insert the tube into the preswaging tool. 3. Make sure that the tube rests firmly on the shoulder of the preswaging tool body and that the nut is fingertight. 4. Mark the nut at the o clock position. 5. While holding the preswaging tool steady, tighten the nut one and one-quarter turns to the 9 o clock position. For /,, and 3/ ; 2, 3, and 4 mm tube fittings, tighten the nut only three-quarters turn to the 3 o clock position (Fig. ).. Loosen the nut. 7. Remove the tube with preswaged ferrules from the preswaging tool. If the tube sticks in the preswaging tool, remove the tube by gently rocking it back and forth. o not turn the tube (Fig. 2). 8. Insert the tube with preswaged ferrules into the fitting until the front ferrule seats against the fitting body. 9. While holding the fitting body steady, rotate the nut with a wrench to the previously pulled-up position; at this point, you will feel a significant increase in resistance. 0. Tighten the nut slightly (Fig. 3). o not use the Swagelok gap inspection gauge with fittings that were assembled using the preswaging tool. Tubing Tools and ccessories Leak etectors, Lubricants, and Sealants For liquid leak detectors, lubricants, and sealants, see the Swagelok Leak etectors, Lubricants, and Sealants catalog, MS 0 9. For tube benders, tube preparation tools, and tube support systems, see the Swagelok Tubing Tools and ccessories catalog, MS 0 79. Tubing Products Swagelok offers a wide variety of tubing products. Contact your authorized Swagelok representative or see these Swagelok catalogs for more information: Stainless Steel Seamless Tubing, Fractional, Metric, and Imperial s, MS 0 8 Ultrahigh-Purity and High-Purity Stainless Steel Tubing, Fractional, Metric, and Imperial s, MS-0-82.

Safe Product Selection When selecting a product, the total system design must be considered to ensure safe, trouble-free performance. Function, material compatibility, adequate ratings, proper installation, operation, and maintenance are the responsibilities of the system designer and user. Caution: o not mix or interchange parts with those of other manufacturers. Warranty Information Swagelok products are backed by The Swagelok Limited Lifetime Warranty. For a copy, visit swagelok.com or contact your authorized Swagelok representative. Swagelok, Hinging Colleting, VCR, VCO, Snoop, Goop, SWK, Ferrule-Pak TM Swagelok Company Krytox TM upont SF 2507 TM Sandvik B 200 205 Swagelok Company Printed in U.S.., GS February 205, R7 MS-0-40