DINSTAR DAG1000-8S and Elastix Server Setup Guide http://www.elastix.org
1.0 Setup Diagram Figure 1-1 is a setup diagram for a single gateway DINSTAR DAG1000-8S configuration. The gateway is setup as a SIP telephony device. Figure 1-1. Setup Diagram 2.0 Host PC Environment Table 2-1. Host Server Environment Details Description Hardware Type Elastix Appliance ELX-Series Hardware Version ELX-3000 Software Type Elastix Software Version 2.4 3.0 Test Setup Equipment Table 3-1. Test Setup Equipment Equipment Model Version IP (SIP) Phone N/A N/A Analog Phone N/A N/A DINSTAR DAG1000-8S 2.16.08.03 PCB 0 LOGIC 0 BIOS 1 Switch N/A N/A 2
4.0 Setup Procedure To set up the Elastix Server for the DINSTAR DAG1000-8S 1. Go to the web address of the Elastix Server Login page. The web address is determined by the customer, for this guide we have used the IP address 192.168.1.75 2. On the Login page, type the username and password for an administrative user into the Username and Password fields, see Figure 4-1. The username and password are determined by the customer. Figure 4-1. Login 3. Press Enter or click on the Submit button to go to Elastix s Dashboard 4. Once inside, click on the PBX tab on the menu at the top of the screen Figure 4-2. Dashboard 3
5. Click on the Submit button to add an extension, see Figure 4-3. This will take you to the Add SIP Extension page. Figure 4-3. Add an Extension 6. On the Add SIP Extension page (Figure 4-4), fill in the following information: User Extension (701 in this example) Display Name ( AnalogPhone in this example) secret ( h7dka3rf9si0t in this example) Figure 4-4. Add SIP Extension 7. Click on Submit button at the end of the page, and you will see a similar page on Figure 4-5 displaying the Apply Configuration Changes Here pink ribbon on top of the screen. Click on there to apply changes. 4
Figure 4-5 8. With this you have just finished creating a SIP extension that will be used by the DINSTAR DAG1000-8S to integrate an analog phone connected to it. Repeat Steps 5 through 7 to similarly create another extension with number (different values on Step 6) to be used by the IP (SIP) Phone to register as well (extension 302 in this example). Once you finished you will see something similar to Figure 4-6. Figure 4-6 9. You will need to enter the information from the extension created on the Elastix Server into the DINSTAR Gateway. For the initial configuration, refer to the DINSTAR DAG8000-8S User Manual found at: http://www.dinstar.com/product/product_23.aspx?typeid=11# Factory default settings WAN Port IP Addressing DHCP LAN Port IP Address 192.168.11.1 Web Access Username admin Web Access Password admin 10. Log in to the DINSTAR Gateway WebUI by pointing your browser to the IP address of the gateway. 11. When prompted, enter the Web Access Password to access to the WebUI (Figure 4-7). 5
Figure 4-7 DINSTAR Gateway WebUI 12. Now we are going to configure the SIP Server into the gateway. Go to the menu SIP Server located on the left side of the DINSTAR Gateway WebUI (Figure 4-8): Primary SIP Server Primary SIP Server Address: Elastix s IP Address ( 192.168.1.75 in this example) Primary SIP Server Port: (Default value) Register Interval: (Default value) Figure 4-8. SIP Server 13. To apply changes click on the button Save. Now go to the menu Port to configure the FXS ports (See Figure 4-9). Figure 4-9. Ports 6
14. Click on the button Add and enter the information of the SIP account that we previously configured in Elastix Server in step 6 (See figure 4-10). Port: 0 (Choose the port you want to configure) Primary Display Name: AnalogPhone Primary SIP User ID: 701 in this example Primary Authenticate ID: 701 in this example Primary Authenticate Password: h7dka3rf9si0t in this example Figure 4-10. Ports 15. When done press Save button. The FXS port now should be registered with Elastix. To check this go to the menu Status & Statistics => Registration (see Figure 4-11). Figure 4-11. Status 16. To test the settings, pick up the previously configured IP (SIP) Phone and call to the analog phone that is connected in the FXS 0 port of the gateway by dialing the number 701. When the call is established, speak into the phone and verify that the other IP (SIP) Phone can hear your voice. Now make a call from analog phone to the IP Phone (from 701 to 302) and check the call is established correctly. If you have troubles when hanging up calls, please check that the Call Progress Tones are correctly configured for your country in the gateway. It is possible that you have to modify some values in the Tones such as frequency, amplitude or cadence. To check this, go to Advanced => FXS / FXO. See Figure 4-12 7
Figure 4-12. FXS / FXO For example in the Busy Tone: - 480 is the first frequency - 230 is the amplitude of the first frequency (The lower this value, the more volume you get) - 620 is the second frequency - 230 is the amplitude of the second frequency (The lower this value, the more volume you get) - 500 is the cadence of the frequency - 500 is the cadence of the silence This step completes the procedure to integrate analog phones with Elastix Server using the DINSTAR DAG1000-8S. 8