AUTOMATED HANDLING CONTINUOUS HANDLING OF UNIT LOADS LA SOLUTION TRANSITIQUE HANDLING SYSTEMS SOLUTION PALLETS RANGE S pal /// RANGE FOR TRANSPORT OF PALLETS UP TO 1500 KG /// 3 STANDARD WIDTHS ADAPTED TO TRANSPORT OF PALLETS 800 X 1200 / 1000 X 1200 / 1200 X 1200
CONTINUOUS HANDLING OF UNIT LOADS MOTORIZED ROLLER CONVEYOR BY ALTERNATING CHAINS, Ø 89 S roll S roll 1500 Rollers ø 89 x 3 are placed at a pitch of 150 mm Standard transport height 500 mm Standard adjustability ± 50 mm (possible from 450 mm to 600 mm) Basic length: 1350 mm Maximum length: 6000 mm (4 pallets of 1500 kg) Standard 10m/mn (possible from 6 to15 m/mn) ENSURE THE LENGTH-WISE HANDLING OF FULL PALLETS SEW-USOCOME gearmotor or equivalent, 230/400 V with 400 V brake, IP54 Protection class B The motor is placed under the frame / IP55 MOTOR PROTECTION CLASS F / PUTTING DOWN CENTERING DEVICES WELDED ON ROLLER COVERS / WELDED GUIDANCE CUPS / SET OF ADJUSTABLE OUTER GUIDES / LATERAL MOTORIZATION ON UNIT MODULE / SENSING DEVICE ROLLER WITH INDUCTIVE SENSOR PNF NF S chain CHAIN CONVEYOR TWIN AND TRIPLE-CHAIN S chain 1500 S chain 1000 Load: Twin-chain up to 1000 kg per pallet Triple-chain up to 1500 kg per pallet Maximum load limited to 6000 kg Basic module l g = 1350 mm length adaptation is possible up to 12 m in only one section Standard transport height 485 mm Standard 10 m/mn (possible from 6 to 15 m/mn) ENSURE THE WIDTH-WISE HANDLING OF FULL PALLETS SEW-USOCOME gearmotor or equivalent, 230/400 V without brake, IP54 protection class B Standard model has the engine placed inside the left beam (other positions are possible, see technical sheet) / IP55 PROTECTION, CLASS F, BRAKE / PLATING BETWEEN BEAMS / METAL CHAIN GUARD AND BACK CENTERING STOP ON PUTTING DOWN MODULE BY FORKLIFT
S turn TURNTABLE S turn 1500 ROLL S turn 1500 CHAIN Rotating part equipped with roller module or triple-chain module. The fixed part includes the rotation control system, common to both applications ROLL and CHAIN. Standard 10 m/mn (possible from 6 to 15 m/mn) Standard rotation = 8 s for ¼ of a turn ENSURE THE CHANGE OF TRANSPORT DIRECTION AT ± 90 WITHOUT CHANGING THE PALLET ORIENTATION COMPARED WITH ITS TRAVEL DIRECTION SEW-USOCOME gearmotor or equivalent, 230/400 V with 400 V brake, IP54 protection class F for the rotation drive Rotation: The rotation is ensured by teethed gear balls driven by a straight-tooth meshing gear, driven by a gearmotor with bevel gear / ROTATING COLLECTOR FOR ROTATION AT 360 / START & ROLL TECHNOLOGY POSSIBLE / SENSING DEVICE ROLLERS WITH INDUCTIVE SENSOR PNP NF / SET OF ADJUSTABLE OUTER GUIDES / PROTECTION SKIRTS WITH INTEGRATED PASSING ROLLERS S cross CROSSROAD TWIN AND TRIPLE-CHAIN S cross 1500 S cross 1000 Basic roller module, with an up and down system by eccentrics, driven by a gearmotor, which can be integrated with a twin and triple-chain, or with a twin or triple-chain integrated. Levelling detection by 2 inductive sensors of ø18 mm Standard transport speed on rollers S = 10 m/mn (possible from 6 to 15 m/mn) Standard transport speed on chains S = 10 m/mn (possible from 6 to 15 m/mn) Standard lifting time 6 s SEW-USOCOME gearmotor or equivalent, 230/400 V, with 400 V brake IP54 Protection class B ENSURE THE CHANGE DIRECTION AT 90 WITH MODIFICATION OF PALLET SCROLL DIRECTION IN RELATION TO ITS DIRECTION OF MOVEMENT / IP55 MOTOR PROTECTION CLASS F / START & ROLL TECHNOLOGY
S trans TRANSFER CONVEYOR S trans 1500 ROLL S trans 1500 CHAIN S trans 1000 CHAIN ENSURE THE DELIVERY OF LOADS BETWEEN DIFFERENT PARALLEL LINES OF CONVEYORS BY A LINEAR DISPLACEMENT MOTION Self-propelling frame equipped with a basic motorized roller module or with a twin or triple-chain basic module. Guidance by central in-floor monorail. Standard displacement speed 10 m/mn Polyurethane tyred wheels for transport directly on the ground SEW-USOCOME gearmotor or equivalent Standard displacement speed 10 m/mn / CENTRAL RAIL GUIDANCE SETTING ABOVE GROUND / EXTENDABLE CABLE SUPPORT / CABLE WINDER SUPPORT ELEVATEUR S elev S elev 1500 ROLL S elev 1500 CHAIN Self-supporting structure including a basic module, with chains or rollers, integrated in a cradle ensuring the vertical linkage between the different required levels. Basic lifting speed 8m/mn SEW-USOCOME gearmotor class F 230/400 V with 400 V brake for a piloting by variable speed drive ENSURE THE CHARGES DELIVERY BETWEEN DIFFERENT CONVEYING LINES LOCATED AT DIFFERENT HEIGHTS BY ELEVATION / MOTORIZED GATES
CONTINUOUS HANDLING OF UNIT LOADS S roll NEW TECHNOLOGY START & ROLL MOTOR ROLLERS CONVEYOR S roll 1500 Module of 1350, 1500, 2700, 3000 with 1 or 2 motor rollers depending on the number of required pallet locations Speed 8, 10, 12, 15 m/mn 0,18 or 0,25 kw DAVID motorized roller depending on the transport speed with charge accumulation management communication system between modules ENSURE THE LENGTH-WISE HANDLING OF FULL PALLETS / START & ROLL TECHNOLOGY / CENTERING DEVICE FOR PALLET UNLOAD / GROUND, LOWERED CONVEYOR, PUTTING DOWN BY PALLET JACK / STAINLESS STEEL AVAILABLE S stacker PALLETS STACKER AND UNSTACKER S stacker S unstacker Pallet handling by 4 PCV fingers, detectors driven by ø50 stroke 80 mm cylinder Levelling detection by 3 inductive sensors of ø18 mm PNP NO short steel case, range 8 mm Standard transport height 500 mm (possible from 450 mm to 600 mm) adjustable ± 50 mm Elevation by a gearmotor SEW-USOCOME brake or equivalent 0,37 kw IP54 Protection class B, for 15 pallets or 500 kg ENSURE THE DISTRIBUTION OF A SINGLE PALLET ON A CONVEYOR STARTING FROM A STACK OF PALLETS OR RE-BUILDING A STACK OF PALLETS BY SUPPLYING THE PALLETS ONE BY ONE / IP55 PROTECTION, CLASS F, BRAKE / FUNCTION STACKER/UNSTACKER (ADDITIONAL SENSOR SUPPORTS) / SPECIAL FINGERS FOR POSSIBLE HANDLING OF 2 PALLET FORMATS / STAINLESS STEEL AVAILABLE
OUR INNOVATIONS AND COMMITMENTS THAT MAKE THE DIFFERENCE! OUR READY FOR USE Our equipments can be delivered pre-wired: Connection to terminal engine cells and sensors following a standard diagram. This diagram may be personalized in different computer formats in order to be integrated in your assembly confi gurations. This option is especially valuable on equipments such as S TURN turntable or S CROSS transfer where the accessibility to some sensors and actuators is difficult because of the compactness of these elements. It allows to save time during the installation and even to prepare the connection before the installation if it has to be done in a short period of time. OUR TRICKS An example: in our turnable, the option rotating collector can be associated with terminal connection in order to obtain a plate which is able to do a rotation of 360 instead of ± 90 in standard. OUR EXCLUSIVE TECHNOLOGY START & ROLL material accessible and parameterizable by everyone! S ROLL 1500, S CHAIN and S TURN products can be equipped with the technology START & ROLL. In addition to our ability to deliver you a pre-wired material, we offer you the possibility to install it and defi ne its operation mode (accumulation without contact, management of trains ) by yourself, without further additions of logic control. Just the safety by independent cabling remains to be dealt with. It is offered as an option. OUR UNIVERSAL To ensure maximum availability of spare parts and facilitate you a minimum SP stock, we aim supply standard equipment with sets that have common parts. For example: the rollers employed in S ROLL 1500 are the same as those used on products S TURN, S CROSS, S TRANS and S ELEV. A same type of roller, as spare parts, wich will fi t all modules that make up your installation. OUR WARRANTY All our equipments are guaranteed for a period of 24 months concerning any manufacturing or material defects, in normal conditions of use, set to our technical sheets, from the delivery date on site. This is serenity insurance for your activity. HANDLING SYSTEMS SOLUTION LA SOLUTION TRANSITIQUE PEINTAMELEC INGÉNIERIE Z.A. de l Artière 12-14 rue des Pâles 63540 ROMAGNAT - France Phone 33 (0)4 73 15 04 80 Fax 33 (0)4 73 15 04 81 Email: s-link@peintamelec.com RCS 352 321 285 - Photo credits: Peintamelec Ingénierie - 02-2012 2008