CAUTION: WHEN HANDLING LEDS DO NOT CUT PROTECTIVE WRAP AVOID TOUCHING OPTICS INSTALL KIT IN FIXTURE THEN REMOVE PROTECTIVE WRAP BEFORE ENERGIZING HOLOPHANE WASHINGTON RETROFIT DECORATIVE LED RETROFIT LUMINAIRE Includes: XRAAB Series IMPORTANT SAFEGUARDS When using electrical equipment, basic safety precautions should always be followed including the following: INSTALLATION INSTRUCTIONS READ AND FOLLOW ALL SAFETY INSTRUCTIONS 1. DANGER RISK OF SHOCK DISCONNECT POWER BEFORE INSTALLATION DANGER RISQUE DE CHOC COUPER L ALIMENTATION AVANT L INSTALLATION 2. This LED retrofit product is UL Classified for use with Washington Series, manufactured by Holophane only. DO NOT install into any other manufacturer s luminaire. To maintain existing Luminaires UL listing, the LED retrofit kit must be UL Classified for use with the manufacturer and model of existing luminaire. Consult CREE Customer support to see if other luminaires are classified to be used with this LED Retrofit kit. Ce produit retrofit LED est classifié UL pour une utilisation avec la série Washington, fabriqué par Holophane seulement. Ne pas installez ce retrofit LED dans le luminaire de tout autre fabricant. Pour maintenir la qualification UL des Luminaires existants, le kit LED retrofit doit être classifié UL pour une utilisation avec le fabricant et le modèle de luminaire existant. Consulter CREE Support Clientèle pour voir si les autres luminaires peuvent être utilisés avec ce retrofit LED. 3. WARNING Risk of fire or electric shock. LED Retrofit Kit installation requires knowledge of luminaires electrical systems. If not qualified, do not attempt installation. Product must be installed in accordance with NEC or your local electrical code. If you are not familiar with these codes and requirements, contact a qualified electrician. ATTENTION- Risque d'incendie ou de choc électrique. L installation du kit retrofit LED exige la connaissance des systèmes électriques pour luminaires. Si non qualifié, ne tentez pas d'installation. Ce produit doit être installé conformément à NEC ou votre code électrique local. Si vous n'êtes pas familier avec ces codes et ces exigences, veuillez contacter un électricien qualifié. 4. WARNING Risk of fire or electric shock. Luminaire wiring and electrical parts may be damaged when drilling for installation of the LED retrofit kit. Check for enclosed wiring and components. ATTENTION - Risque d'incendie ou de choc électrique. Câblage électriques peuvent être endommagés lors du perçage pour l'installation du kit retrofit LED. Vérifier les fils et composants. 5. WARNING Risk of fire or electric shock. Check the existing wiring for damage before installing retrofit kit. Do not install if existing wires are damaged. ATTENTION- Risque d'incendie ou de choc électrique. Vérifiez si le câblage existant n est pas endommagé avant l'installation du kit retrofit LED. Ne pas installer si des fils sont endommagés. 6. WARNING To prevent wiring damage or abrasion, do not expose wires to the edge of sheet metal or any other sharp objects. ATTENTION - Pour éviter les dégâts de câblage par l'abrasion, ne pas mettre en contact les fils électriques avec des bords de tôle ou d'autres objets pointus. 7. WARNING Risk of fire or electric shock. Install this kit only in the luminaires that have the construction features and dimensions shown in the photographs and/or drawings. ATTENTION - Risque d'incendie ou de choc électrique. Installez ce kit seulement dans les luminaires qui ont les caractéristiques de construction et les dimensions dans les photographies ou les dessins de la page suivante. 8. Do not make or alter any holes in a wiring enclosure or electrical components during the kit installation. Ne pas modifier ou faire de trous dans une boite de câblage ou compartiment électrique lors de l'installation du kit. 9. Ensure that the existing luminaire is installed according to original manufacturer s specification. S'assurer que les luminaires sont installés selon les spécifications du fabricant. 10. Only the holes indicated in the photographs or drawings may be made or altered as a result of the kit installation. Do not leave any other holes open in a wiring enclosure or electrical component. Seulement les trous indiqués dans les photographies ou les dessins peuvent être faits ou altérés pour l installation du kit retrofit LED. Ne laissez aucun trou ouvert dans le compartiment électrique. 11. The retrofit kit contains a universal LED driver and can be operated at voltages of 120-277V. Le kit de rénovation contient une alimentation universelle et peut fonctionner à des tensions de 120-277V. 12. Once the Retrofit kit is installed, the luminaire can no longer accept HID lamps and shall not be converted back to an HID luminaire. Une fois le kit retrofit LED installé, l'appareil peut ne plus accepter les lampes HID et ne pourra pas être retransformé en luminaire HID. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE LIST OF SUPPLIED COMPONENTS 1. XRA Series Driver Assembly 2. XRA Series LED Module Assembly. 3. (1) Flat Washer 4. (1) Beveled Washer 5. (1) Nut 6. (1) #12-24 X 0.375 Screw 7. (1) Air Craft Cable Handle (1 supplied per order) Page 1 of 5
RETROFIT FIXTURE INSTALLATION NOTE: Consult your local authority regarding disposal or recycling of removed ballast, capacitor and lamp. 1. Disconnect power to fixture. 2. Verify the existing luminaire model. See Figure 1. FIGURE 1 6. Disconnect the Lamp Socket Wires and the Photocell wires, if present, and discard the terminal block assembly. 7. On the inside of the ballast Compartment, remove the (2) screws securing the lamp socket to the bottom surface of the globe. See Figure 4. FIGURE 4 3. Loosen the (2) bolts securing the Ballast Compartment Door to the housing and separate the assembly from the housing. See Figure 2. 8. Remove the Lens Cap and Finial assembly and set aside. See Figure 5. FIGURE 5 FIGURE 2 4. Disconnect the wire harness and set the ballast assembly aside. 5. Separate the terminal block bracket by removing the screw securing it to the inside of the housing. Replace the screw for future ground connection. See Figure 3. 9. Remove the Lamp and Lamp socket from the globe by lifting it out and discard. See Figure 6. FIGURE 6 FIGURE 3 10. Carefully remove the red plastic protective wrap form the LEDs by peeling it back by the label and avoid touching the LEDs. See Figure 7. Page 2 of 5
FIGURE 7 FIGURE 9 11. Insert the LED Module Assembly by lowering it into the globe ensuring to avoid touching the LEDs as shown in FIGURE 8. FIGURE 8 13. Replace the Lens Cap and Finial assembly removed in Step 8. 14. Inside the Ballast Compartment, screw in the supplied #12-24 X 0.375 Screw in to one of the two socket screw holes. 15. Inside the Ballast Compartment, secure the Retrofit LED Module Assembly by threading first the Flat Washer over the LED Module Assembly Leads followed by the Beveled Washer with the concave side facing downward and then secure the assembly with the Nut. See Figure 10. FIGURE 10 NOTE: To ease the installation of the LED Module Assembly into the top of the globe, use the Air Craft Cable Handle by looping each end of the cable over a Heatsink Fin to create a handle. See Figure 8a. FIGURE 8a 16. Remove the ballast assembly from the Ballast Compartment Door by removing the (3) bolts securing the metal mounting bracket to the mounting bosses on the inside of the door. Discard the ballast and save the removed bolts for mounting the Retrofit LED Driver Assembly. See Figure 11. FIGURE 11 12. Line up the threaded nipple with the wireway and gently release the assembly into the globe. See Figure 9. 17. Using the screws removed in Step 13; mount the Retrofit LED Driver Assembly to the Ballast Compartment Door. Using the screw removed in Step 5, secure the attached ground lead to the inside of the Ballast Compartment. See Figure 12. Page 3 of 5
SUPPLY WIRING SUPPLY WIRING FIGURE 12 18. See the Electrical Connections section for wiring instruction. 19. Once electrical connections are made, insert the Retrofit LED driver Assembly in the Ballast Compartment. See Figure 13. FIGURE 13 ELECTRICAL CONNECTIONS NOTE: Ground connection should include previous luminaire ground as well as ground from retrofit panel. Verify that the supply voltage is within the fixture s voltage rating. 1. For 120-277V applications make the following Electrical Connections to the terminal block located on the side of the Retrofit LED Driver Assembly: a. Connect the black lead to the voltage supply lead b. Connect the white lead to the neutral supply lead c. Connect the green or green/yellow ground lead to the supply ground lead 2. If Dimming is an option, make the following additional connections using Class 1 wire: a. Connect the violet dimming positive lead to the supply dimming positive lead. b. Connect the grey dimming negative lead to the supply dimming negative lead 120-277V STANDARD FIXTURE WIRING BLACK GREEN LINE BLACK GROUND GREEN WHITE VIOLET GREY NEUTRAL WHITE DIM (+) VIOLET DIM (-) - GREY (DIMMING OPTIONAL) 20. Re-tighten the (2) bolts removed in Step 3 to secure the Ballast Compartment Door to the housing. 21. Reconnect power to the fixture. 3. For 208/240/480V applications, make the following Electrical Connections to the terminal block located on the side of the Retrofit LED Driver Assembly: a. Connect L2 (Hot) supply lead to the black lead. b. Connect L1 (Hot) supply lead to the white lead c. Connect the green or green/yellow ground lead to the supply ground lead If Dimming is an option, make the following additional connections using Class 1 wire: d. Connect the violet dimming positive lead to the supply dimming positive lead. e. Connect the grey dimming negative lead to the supply dimming negative lead 208/240/480V PHASE TO PHASE FIXTURE WIRING LINE (L2) GROUND LINE (L1) VIOLET GREY LINE BLACK GROUND GREEN NEUTRAL WHITE DIM (+) VIOLET DIM (-) - GREY (DIMMING OPTIONAL) Page 4 of 5
FIELD ADJUSTABLE DIMMING NOTE: This luminaire is provided with field adjustable dimming. Luminaires leave the factory adjusted to the maximum setting which is Position 9 as shown in Figure 14. FIGURE 14 1. Locate the luminaires electrical label and verify the maximum wattage available. 2. Establish the desired wattage on the following table and turn the switch to the correlating position. Position 65-69W 97W Input Power Multiplier Input Power Multiplier 9 1.00 1.00 8 0.92 0.87 7 0.88 0.83 6 0.81 0.78 5 0.77 0.72 4 0.73 0.65 3 0.67 0.58 2 0.60 0.51 1 0.49 0.44 Page 5 of 5