INSTALLATION INSTRUCTIONS

Transcription

1 INSTALLATION INSTRUCTIONS VOLT LED Edge-Lit Flat Panel VFP-22 and VFP-24 Series Help Hotline: Mon-Fri 8am-8pm Sat-Sun 10am - 6pm (EST) Specifications and product details subject to change without notice. Copyright 2015, VOLT Lighting, Lutz FL USA All rights reserved.

2 INSTALLATION INSTRUCTIONS VOLT VFP-22 and VFP-24 Series! Important: Please Read Before Installation This equipment is intended to be installed only by qualified personnel. The installation must be made in accordance with the current edition to the National Electric Code and all applicable state and local building codes.failure to adhere to these codes and instructions may result in serious injury, property damage and void the warranty. The final installation must be approved by the appropriate qualified electrical/building inspector(s).! Important Safety Instructions These instructions do not intend to cover all variations in installation, operation, maintenance or mounting situation. Make sure that the power is turned OFF before installing or servicing this fixture. 1. Review the diagrams thoroughly and disconnect all electrical power before installation to avoid electric shock. 2. Do not mount near flammable materials or electric heaters. 3. Do not let power supply cords touch hot surface. 4. Fixture is for indoor and dry location. NOT use for outdoor location. 5. The fixture shall be installed or maintained by qualified electrician or person who is familiar with the fixture. Package Contents A. (1) LED Fixture a. VFP-2230-W VOLT 2x2 LED Edge-Lit Flat Panel 3000K b. VFP-2240-W VOLT 2x2 LED Edge-Lit Flat Panel 4000K c. VFP-2430-W VOLT 2x4 LED Edge-Lit Flat Panel 3000K d. VFP-2440-W VOLT 2x4 LED Edge-Lit Flat Panel 4000K E. (1) LED Driver in Junction box F. (4) T-Bar Clips

3 Product Dimensions Wire Connections Remove Access Panel Screw Access Panel Remove access panel from back of LED panel by removing screws. Driver 2 Wire Supply Wires Black Supply Wire (Line) Ground Wire from Driver White Supply Wire (Neutral) Ground Wire from Supply J-box Blue Input Wire (Neutral) Wire Nut Brown Input Wire (Line) Knockout Pry out one knockout from side of J-box. Insert supply wires from ceiling inside of J-box. Connect white supply wire (neutral) to brown input wire (neutral) from driver. Connect black supply wire (line) to black input wire (line) from driver. Connect ground wire from supply to ground wire from driver. Wrap each wire nuts until wires are tightly joined together with approved electrical tape.

4 INSTALLATION INSTRUCTIONS VOLT VFP-22 and VFP-24 Series 3 Cover Wires for Dimmer and Reattach Access Panel Wire Nut Blue Output Wire Lock Screw Access Panel White Output Wire J-Box If not connecting a dimmer, screw wire nut or attach a crimp connector onto each of unused dimming output wires (blue wire and white wire) on driver. These wires are used for dimming functions and need to be capped off if they are not being used. If connecting a dimming device, please refer to the DIMMING FUNCTION CONNECTION INSTRUCTIONS. Carefully tuck all wires into J-box, and replace access panel with screws. Recessed Installation 1 Locate Tilt fixture and insert through opening in ceiling grid, facing down. Ceiling Grid

5 2 Install Rotate T-Bar Clip Ceiling Grid When fixture is above the ceiling grid, position it so the frame of the fixture is flat, level and supported by the T-Bar grid. Rotate T-bar clips counter clockwise (90 degrees) to secure panels. If desired or required by local code, wire cable can be run through holes in T-Bar clips and attached to rafters for additional support. Surface Mount Installation 1 Install Side Frames J-Box Wood Screw Side Frame IMPORTANT: Frame should be positioned over J-box so as not to interfere with J-box on the back of LED panel. Position 3 sides together making sure to use two 2 foot sides with moutning holes. Mount 3 sided frames to ceiling with wood screws. Make sure power supply box does not interfere with driver box on back of panel. It is recommended that the power supply / J-box is mounted off-center of frame.

6 INSTALLATION INSTRUCTIONS VOLT VFP-22 and VFP-24 Series 2 Install Side Frame Screw 4th of Side Frame Refer to WIRE CONNECTION INSTRUCTIONS to connect wires. Slide LED panel into fixed side frames and then attach 4th of side frame. Secure with screws and tighten until snug. Pendant Mount Installation 1 Install Wire Grippers and Ropes Wire Gripper Rope Ceiling Canopy Attach wire grippers to back corners of LED panel and bottom corners of ceiling canopy. Measure desired rope length and then feed ropes through each wire gripper at the same direction. Wire Gripper

7 2 Install Ceiling Canopy Outlet Box Supply Wires Crossbar Lock Screw Outlet Box Screw Ceiling Canopy Pull supply wires through center hole of crossbar and ceiling canopy and refer to WIRE CONNECTION INSTRUC- TIONS to connect wires. Attach crossbar to outlet box and secure with outlet box screws. Hand tighten until snug. Push ceiling canopy over outlet box and secure by threading lock screws into crossbar. 3 Level Wire Gripper Wire Gripper Rope Press Level LED panel by fine tuning the length of rope by pressing the strain reliefs at the canopy and feed the wires in or out as necessary. Cut excess rope after final adjustment. Maintenance: When cleaning the fixture, switch of power to the fixture and let it cool completely. Clean the fixture with a soft cloth and water. Never use any cleaner that is not a standard PH neutral detergent.

8 INSTALLATION INSTRUCTIONS VOLT VFP-22 and VFP-24 Series Dimming Function Connection If you wish to use the dimming function, connect the dimming signal wires from a compatible dimming control system to the DIM+ (blue wire on the LED power supply) and the DIM- (white wire on the LED power supply). DO NOT connect DIM- to -V. Reference resistance values for output current adjustment (Typical) for potentiometer 1-10VDC dimming function for Output current adjustment (Typical) 10V PWM signal for output current adjustment (Typical): Frequency range: 100Hz ~ 3KHz

9 Using the built-in dimming function on power supply cannot turn the lighting fixture totally off. Refer to the connection method below to achieve 0% brightness (full off) of the lighting fixture connecting to the LED power supply unit. Using a switch and relay can turn the fixture ON/FF. 1. Output constant current level can be adjusted through output cable by connecting a resistor or 1~10Vdc or 10VPWM signal between DIM+ and DIM-. 2. The LED lighting fixture can be turned ON/OFF by the switch. Adjust the position of the fixture properly and clean the surface of the panel if required with water and soft cloth. After proper installation of the fixture, switch on the AC power to turn on the LED panel. Your installation is now completed and ready to use. Retain this sheet for future reference.

10 Help Hotline: Mon-Fri 8am-8pm Sat-Sun 10am - 6pm (EST) Specifications and product details subject to change without notice. Copyright 2015, VOLT Lighting, Lutz FL USA All rights reserved. is-vfp-ver1.pdf