INSTALLATION MANUAL VEHICLE SECURITY SYSTEM CE-SS200

INSTALLATION MANUAL VEHICLE SECURITY SYSTEM CE-SS200

FUSION CULTURE TABLE OF CONTENTS There s no point doing something if no one notices. We ve always believed the way to make things happen is by getting noticed. From our product, to our demo cars, to our events, FUSION is about making some noise. Now you are ready. Step out of the shadows and announce you ve arrived in a world where the old limits are left behind. Where technology is creatively combined with the latest in product innovation. Where new levels of entertainment are delivered with outstanding performance and quality. Our development team create distinctively different products; subwoofers, amplifiers, speakers and peripherals that redefine what can be done in car audio. PROGRAMMING REMOTES................................. pg 4 ALARM FEATURES PROGRAMMING......................... pg 5 ADJUSTING THE SENSITIVITY LEVEL......................... pg 8 WIRING DIAGRAMS........................................ pg 9 CENTRAL LOCKING DIAGRAMS............................. pg 11 SPECIFICATIONS.......................................... pg 15 Leave the old behind and push the limits of what can be achieved in car audio. Make some noise. For more information about FUSION Electronics visit our website at www.fusionelectronics.com or email technical@fusionelectronics.co.nz PROFESSIONAL INSTALLATION STONGLY RECOMMENDED Installation Precautions: 1. Roll down window to avoid locking keys in vehicle during installation 2. Avoid mounting components or routing wires near hot surfaces 3. Avoid mounting components or routing wires near moving parts 4. Tape or loom wires under hood for protection and appearance 5. Use grommets when routing wires through metal surfaces 6. Use a voltmeter for testing and verifying circuits RECORD YOUR PRODUCT DETAILS HERE: MODEL NUMBER DATE OF PURCHASE AFFI RECEIPT HERE V 2.0 2 3

PROGRAMMING REMOTES 1. Turn the ignition switch OFF/ON 3 times (within 15 seconds) and leave in the ON position. 2. Push the valet switch 3 times, and hold on the 3rd push until a long chirp is heard from the siren, and then release the valet switch. You are now in the remote programming mode. 3. Press and hold any button of the remote until the siren responds with a confirming chirp, this indicates the remote has been stored into memory. 4. If you have additional remotes (up to 4 in total) that need to be programmed, repeat step 3 for each remote. Exit Programming: Turn ignition to OFF position, or wait for 15 seconds. Three long chirps and three indicator light flashes will confirm exit. Note: This mode will only retain the last 4 remote transmitters programmed. If the remote memory is exceeded, the security system will start deleting remote s from memory in chronological order. ALARM FEATURES PROGRAMMING: ALARM FEATURE I PROGRAMMING: 1. Turn the ignition switch ON/OFF 3 times (within 15 seconds) and leave in the OFF position on the 3rd time. 2. Push the valet switch twice, and hold on the 2nd push until one short chirp, followed by one long chirp is heard then release the valet switch. You are now in the alarm feature I programming mode. 3. A; Press and release the remote button corresponding to the feature 1 to be changed. The siren will chirp and the LED will indicate the new setting B; Press and release the remote button corresponding to the feature 2 to be changed. The siren will chirp and the LED will indicate the new setting C; Press and release the remote buttons + corresponding to the feature 3 to be changed. The siren will chirp and the LED will indicate the new setting Note: The factory default setting is always [1] LED flash, [1] chirp. Press remote button One Chirp / LED one flash Factory Default Setting Two Chirps / LED two flashes 1 Chirps on Chirps off 2 Automatic Rearm On Automatic Rearm Off 3 + Instant Door Ajar Warning 45 second Delay Door Ajar warning Exit Programming: Turn ignition to ON position, or wait 15 seconds. Three long chirps will confirm exit. 4 5

ALARM FEATURE II PROGRAMMING: 1. Turn the Ignition switch ON/OFF 3 times (within 15 seconds), and leave in the OFF position. 2. Push the valet switch 4 times and hold on the 4th push until two short chirps and one long chirp is heard, and then release the valet switch. You are now in the alarm feature II programming mode. 3. A; Press and release the remote button corresponding to the feature 1 to be changed. B; Press and release the remote button corresponding to the feature 2 to be changed. C; Press and release the remote buttons + corresponding to the feature 3 to be changed. Note: The factory default setting is always [1] LED flash, [1] chirp. ALARM FEATURE III PROGRAMMING: 1. Turn the ignition switch ON/OFF 3 times (within 15 seconds), and leave in the OFF position. 2. Push the valet switch 6 times and hold on the 6th push until three short chirps and one long chirp is heard, and then release the valet switch. You are now in the Alarm feature III programming mode. 3. A; Press and release the remote button corresponding to the feature 1 to be changed. B; Press and release the remote button corresponding to the feature 2 to be changed. C; Press and release the remote buttons + corresponding to the feature 3 to be changed. Note: The factory default setting is always [1] LED flash, [1] chirp. Press remote button One Chirp / LED one flash Factory Default Setting 1 0.9 - second door lock pulses Two Chirps / LED two flashes 3.0 - second door lock pulse 2 Active arming Passive arming without passive door locking 3 + Ignition controlled door locks & unlocks Without ignition controlled door locks & unlocks Three Chirps / LED three flashes double pulse unlock Passive arming with passive door locking Press remote button One Chirp / LED one flash Factory Default Setting Two Chirps / LED two flashes 1 Shock sensor program mode 2 Red/white wire = trunk/boot (Channel 3) output Red/white wire = two step door unlock output 3 + Anti car jacking off Anti car jacking on Exit Programming: Turn Ignition to ON position, or wait for 15 seconds. Three long chirps will confirm exit. Exit Programming: Turn ignition to ON position, or wait for 15 seconds. Three long chirps will confirm exit. 6 7

ADJUSTING THE SENSITIVITY LEVEL OF THE SHOCK SENSOR 1. Turn the ignition switch ON/OFF 3 times (within 15 seconds) and leave in the OFF position. 2. Push the valet switch 6 times and hold on the 6th push until three short chirps and one long chirp is heard, and then release the valet switch. You are now in the alarm feature Shock Sensor programming mode. 3. Press and hold button for 2 seconds. One long siren chirp will indicate the unit is ready to accept adjustments of the second stage of the shock sensor (full alarm). 4. Pressing the button on the remote once will decrease the sensitivity level by one, each time a decrease is made the siren will respond with one chirp, while 2 chirp s indicates the minimum sensitivity setting. 5. Pressing button on the remote once will increase sensitivity level by one, each time an increase is made the siren will respond with one chirp, while 2 chirp s indicates the maximum sensitivity setting. 6. Hit the bumper or strong metal part of the vehicle to test the threshold level of the sensor. a). Activate the warn-away (first stage of the shock sensor), the siren will emit a short chirp. b). Activate the full alarm (second stage of the shock sensor), the siren will emit a long chirp. 7. When you are satisfied with the second stage of the shock sensor settings, press and hold and buttons simultaneously for 2 seconds. Two long siren chirps will indicate the unit is ready to accept adjustments of the first stage of the shock sensor (warn-away). 8. Follow the steps 4, 5 and 6 to adjust the warn-away sensitivity. 9. When you are satisfied with the setting, press and buttons simultaneously. One long siren chirp indicates the unit has confirmed the setting. WIRING DIAGRAM Black Antenna Wire Valet Switch 2Pin Blue A: MAIN 6 PIN WIRE HARNESS: 1. White Wire: Turn Indicator Relay Output 2. Red / Blue Wire: Turn Indicator Relay Power input 3. White Wire: Turn Indicator Relay Output 4. Black Wire: Ground to Vehicle FRAME 5. Brown Wire: Positive output To Siren 6. Red Wire: To Constant Battery Source 6Pin White 2Pin White 6Pin White 6Pin White Turn Indicator 6PinMiniConnector 6PinDoor/Unlock Wire harness Main 6 Pin Wire harness 10A Fuse 3A Fuse LED Indicator Note: If 20 seconds of inactivity expire, or the ignition is turned on during the above steps, the unit will exit the programing mode and return to the disarmed mode. Three long chirps will confirm exit. 8 9

B: 6 PIN MINI CONNECTOR WIRE HARNESS: A: CENTRAL LOCKING DIAGRAMS (After market Door Motors) INSTALLING DOOR LOCK MOTORS (2 WIRE) 1. Violet Wire: Positive Door Pin Switch Input 12V Green/ white Blue/ white 2. Blue Wire: Instant Trigger Ground Input Blue/ red Green/ red 3. Green Wire: Negative Door Pin Switch Input 4. Yellow Wire: To Ignition Switched 12V Blue/ yellow Green/ yellow 5. Orange Wire: 200mAGrounded when armed 6. Red/White Wire: (-) 200mA Programmable Output Channel 3 / 2 Step Door Unlock. From ignition switch Cut Red wire 30 Yellow wire 85 87a 86 To start solenoid White wire Orange wire INSTALLING 4 DOOR LOCK MOTORS (WITH 5-WIRE LOCK MOTOR) Blue/ red Green/ red Green/ white Blue/ white C: 6PIN DOOR LOCK/UNLOCK WIRE HARNESS: (See central locking diagrams) Blue/ yellow Green/ yellow To Door UnlockControl Wire To Door Control Wire Blue/Red Wire: (87a) - Door Unlock Relay Blue/White Wire: (30) -DoorUnlockRelay Blue/Yellow Wire: (87) - Door Unlock Relay Green/Red Wire: (87a) -Door Relay Green/White Wire: (30) - Door Relay Green/Yellow Wire: (87) -DoorRelay B: CENTRAL LOCKING DIAGRAMS (Factory Door ing System) NEGATIVE TRIGGER DOOR LOCK SYSTEM Green / white Blue / white Green / yellow Door Door unlock Master ing Switch Blue / yellow 10 11

POSITIVE TRIGGER DOOR LOCK SYSTEM Green / white Blue / white Door Green /yellow Blue / yellow ALTERNATING DOOR LOCKS Green/ red Green/ white Blue/ red Blue/ white Green/ yellow Blue/ yellow Master Door Switch Splice Cut the Existing Unlock Wire Splice Door unlock + 12V To Slave Door switches Master ing Switch Cut the Existing Wire To Door 2 STEP DOOR UNLOCK WIRE CONNECTIONS FOR 5 WIRE ALTERNATING DOOR LOCKS 6-Pin Door Wire Harness + 12V Red / White Green / Red Green / White Green / Yellow Blue / Yellow Blue / Red Blue / White OEM Driver's Door Motor 86 87 87A 30 85 Unlock Cut the Unlock Wire Cut Existing Unlock Wire OEM Door Master Unlock x x Cut the Existing Wire OEM Slave Door Switch To All Other Door Motors 2 STEP DOOR UNLOCK WIRE CONNECTIONS FOR GROUND SWITCHED DOOR LOCKS Red / White OEM Door Master Switch VACUUM OPERATED DOOR LOCKING SYSTEM Green/ white Blue/ red Green/ red Door Switch Cut Blue/ white 6-Pin Door Wire Harness Blue / Red Blue / White Green / White Green / Yellow Unlock Existing Unlock Wire Existing Wire Green/ yellow Blue/ yellow Compressor Blue / Yellow OEM Door Relay OEM Door Motor Cut Existing Unlock Wire To All Other Door Motor 12 13

2 STEP DOOR UNLOCK WIRE CONNECTIONS FOR POSITIVE SWITCHED DOOR LOCKS Red / White 87 86 87A 85 30 6-Pin Blue / Red Door Blue / White Wire Green / White Harness Green / Yellow Blue / Yellow Unlock Existing Pos. Unlock Wire OEM Door Master OEM Door Relay Existing Pos. Wire SPECIFICATIONS: Power supply: 10 VDC 16 VDC Operating temperature: -40 C +80 C (-40 F +176 F ) T Frequency: 433.92 M Hz POWER CONSUMPTION: Indicator light flash output: Door : Door Unlock: Security system (disarmed): 15 Amp 10 Amp 10 Amp 15 ma Note: Remote control range is dependant on weather conditions and alarm installation. OEM Driver's Door Motor Cut Existing Unlock To All Other Door Motors THE FUSION CE-SS200 SECURITY SYSTEM COMPLIES WITH: FCC: This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions. (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Z105 YOU CAN HELP PROTECT THE ENVIRONMENT! Please remember to respect the local regulations: Hand in the non-working electrical equipment to an appropriate waste disposal center. PUBLISHED BY FUSION ELECTRONICS LIMITED: Copyright 2007 by FUSION Electronics Limited. All rights reserved. Specifications and design are subject to change without notice. 14 15

Specifications and design are subject to change without notice