CUTTING TOOLS FOR MACHINE SHOP USE WORK HOLDING TOOLS, CUTTING TOOLS AND SHOP ACCESSORIES T-Slot Bolts Nuts and Washers Set-up Wedges 14 FRONT SIDE WORK HOLDING TOOLS MACHINE SHOP USE Nut Washer T-Slot Bolt SIDE
14 Work-Holding Tools T-Slot Bolts, Carbon Steel, Black Finish Forged T-Slot Bolts are used for setting up work on planers, shapers, milling machines, and other machine tools equipped with T-slot tables. Will fit T-slot without machining and cannot turn or break out of table slots. Available in Unified National Coarse, U.N.C. thread only. T-Slot Bolts, 3/8" T-Slot Size Product Weight, Length Under Number lbs. Head, Inches 79-551 0.04 1.000 79-555 0.06 1.500 79-559 0.08 2.000 79-561 0.09 2.500 79-565 0.11 3.000 79-569 0.14 4.000 3/8 T-Slot Bolts, 1/2" T-Slot Size Product Weight, Length Under Number lbs. Head, Inches 79-587 0.15 1.500 79-591 0.16 2.000 79-595 0.18 2.500 79-599 0.21 3.000 79-601 0.24 3.500 79-603 0.26 4.000 79-605 0.29 4.500 79-607 0.31 5.000 79-611 0.36 6.000 1/2 3/16 9/32 T-Slot Bolts, 5/8" T-Slot Size Product Weight, Length Under Number lbs. Head, Inches 79-627 0.24 1.500 79-631 0.28 2.000 79-635 0.31 2.500 79-639 0.35 3.000 79-641 0.39 3.500 79-643 0.45 4.000 79-645 0.48 4.500 79-647 0.53 5.000 79-649 0.56 5.500 79-651 0.61 6.000 79-653 0.71 7.000 79-655 0.77 8.000 79-659 0.95 10.000 1/2 5/8 7/8 T-Slot Bolts, 3/4" T-Slot Size Product Weight, Length Under Number lbs. Head, Inches 79-679 0.52 2.500 79-683 0.57 3.000 79-685 0.63 3.500 79-687 0.68 4.000 79-689 0.75 4.500 79-691 0.82 5.000 79-693 0.87 5.500 79-695 0.95 6.000 79-697 1.04 7.000 79-699 1.16 8.000 79-703 1.43 10.000 3/4 7/16 1-3/16 T-Slot Bolts 7/8" T-Slot Size, 3/4" Diameter Bolt Product Weight, Length Under Number lbs. Head, Inches 79-727 0.89 4.000 79-729 0.96 4.500 79-731 1.01 5.000 79-735 1.14 6.000 79-739 1.38 8.000 79-743 1.65 10.000 3/4 T-Slot Bolts 1" T-Slot Size, 7/8" Diameter Bolt Product Weight, Length Under Number lbs. Head, Inches 79-757 1.09 3.000 79-759 1.27 4.000 79-761 1.44 5.000 79-763 1.59 6.000 79-765 1.78 7.000 79-767 1.96 8.000 79-771 2.28 10.000 7/8 9/16 7/8 1-1/2 1 9/32 7/8 5/8 1-3/4 14-1 Always wear eye protection when near tools in use.
Work-Holding Tools 14 T-Slot Nuts For use with threaded studs on machine tools equipped with slotted tables. Forged nuts will fit T-slots without machining, and duplicate dimensions of T-Slot Bolts. Available in Unified National Coarse, U.N.C. thread only. Product T-Slot Size, U.S. Standard Weight, Number Inches Thread Pounds 79-825 0.625 1/2" - 13 mm 0.17 79-827 0.750 5/8" - 11 mm 0.28 79-829 0.875 3/4" - 10 mm 0.39 79-831 1.000 7/8" - 9 mm 0.57 Hex Nuts For use with T-Slot Bolts. Heat treated for added strength. Available in Unified National Coarse, U.N.C. thread only. Product Bolt Dia., Across Flats, Thickness, Weight, Number Inches Inches Inches lbs. 79-841 0.375 0.687 0.500 0.04 79-843 0.500 0.875 0.625 0.08 79-845 0.625 1.062 0.750 0.15 79-847 0.750 1.250 0.875 0.24 79-849 0.875 1.437 1.000 0.35 Washers For use with T-Slot Bolts, Washers are heavy and extra thick. Heat treated for added strength. Product Bolt Dia., I.D., O.D., Thickness, Weight, Number Inches Inches Inches Inches lbs. 79-859 0.375 0.437 0.812 0.187 0.02 79-861 0.500 0.562 1.000 0.187 0.03 79-863 0.625 0.718 1.250 0.250 0.06 79-865 0.750 0.843 1.500 0.250 0.08 79-867 0.875 0.968 1.750 0.250 0.12 Set-Up Wedges Maximum Product Length, Width, Thickness, Weight, Number Inches Inches Inches lbs. 79-493 3.000 1.000 0.250 0.11 79-495 5.000 1.000 0.500 0.31 79-496 6.000 1.250 0.750 0.68 14-2
14 High Speed Steel Ground Tool Bits and Cut-Off Blades Available in two versatile grades of High Speed Steel, M-2 and M-34, bits and blades are ground on all sides and ready for use. Packaged for convenient handling. Each tool is clearly marked with size and product number. Steel Analysis M-2 Tungsten Moly High Speed Steel Carbon,.84%; Manganese,.25%; Silicon,.30%; Tungsten, 6.40%; Chromium, 4.15%; Vanadium, 1.90%; Molybdenum, 5.00%. M-34 Cobalt High Speed Steel Carbon,.90%; Manganese,.30%; Silicon,.30%; Tungsten, 1.55%; Chromium, 3.75%; Vanadium, 2.00%; Molybdenum, 8.70%; Cobalt, 8.00%. Square Tool Bits, M-2 H.S.S. Ends Beveled 10 86-001 0.187 2.000 0.02 86-003 0.250 2.500 0.04 86-005 0.312 2.500 0.07 86-007 0.375 3.000 0.12 86-011 0.500 4.000 0.29 86-013 0.625 4.500 0.51 Square Tool Bits, M-34 H.S.S. Ends Beveled 10 86-041 0.187 2.000 0.02 86-043 0.250 2.500 0.04 86-045 0.312 2.500 0.07 86-047 0.375 3.000 0.12 86-051 0.500 4.000 0.29 86-053 0.625 4.500 0.51 86-055 0.750 5.000 0.82 Cut-Off Blades, M-2 H.S.S. For Straight and Right-Hand Tools Ends Beveled 86-257 0.093 x 0.500 4.500 0.05 86-259 0.093 x 0.625 5.000 0.07 86-261 0.125 x 0.750 5.000 0.12 86-263 0.125 x 0.875 6.000 0.16 86-265 0.187 x 1.000 6.500 0.28 14-3 Always wear eye protection when near tools in use.
14 Cut-Off Blades, M-34 H.S.S. For Straight and Right-Hand Tools Ends Beveled 86-291 0.093 x 0.500 4.500 0.05 86-293 0.093 x 0.625 5.000 0.07 86-295 0.125 x 0.750 5.000 0.12 86-297 0.125 x 0.875 6.000 0.16 86-299 0.187 x 1.00 6.500 0.28 High Speed Steel Unground Tool Bits and Cut-Off Blades Made from M-2 High Speed Steel and carefully hardened, these tool bits and blades are ready for finish grinding. Square Tool Bits For Turning Tools 86-391 0.187 2.000 0.02 86-393 0.250 2.500 0.05 86-395 0.312 2.500 0.07 86-397 0.375 3.000 0.12 86-399 0.437 3.500 0.19 86-401 0.500 4.000 0.29 Square Tool Bits For Boring Tools 86-421 0.187 1.250 0.01 86-423 0.250 1.750 0.03 86-425 0.312 2.250 0.06 86-427 0.375 2.625 0.11 Cut-Off Blades For Straight and Right-Hand Tools 86-471 0.093 x 0.500 4.500 0.04 86-473 0.093 x 0.625 5.000 0.07 86-475 0.125 x 0.750 5.000 0.12 86-477 0.125 x 0.875 6.000 0.17 86-479 0.187 x 1.000 6.500 0.28 14-4
14 Left-Hand Turning Tool Made from M-2 High Speed Steel and carefully heat treated, these tool bits are ground to ten popular, versatile shapes and ready for use. 86-531 0.250 2.500 0.04 86-559 0.312 2.500 0.07 86-583 0.375 3.000 0.12 Round Nose Turning Tool Made from M-2 High Speed Steel and carefully heat treated, these tool bits are ground to ten popular, versatile shapes and ready for use. 86-533 0.250 2.500 0.04 86-561 0.312 2.500 0.07 86-585 0.375 3.000 0.12 Right-Hand Turning Tool Made from M-2 High Speed Steel and carefully heat treated, these tool bits are ground to ten popular, versatile shapes and ready for use. 86-537 0.250 2.500 0.04 86-563 0.312 2.500 0.07 86-587 0.375 3.000 0.12 Left-Hand Corner Tool Made from M-2 High Speed Steel and carefully heat treated, these tool bits are ground to ten popular, versatile shapes and ready for use. 86-539 0.250 2.500 0.04 86-565 0.312 2.500 0.07 86-589 0.375 3.000 0.12 14-5 Always wear eye protection when near tools in use.
14 Threading Tool Made from M-2 High Speed Steel and carefully heat treated, these tool bits are ground to ten popular, versatile shapes and ready for use. 86-541 0.250 2.500 0.04 86-567 0.312 2.500 0.07 86-591 0.375 3.000 0.12 Right-Hand Corner Tool Made from M-2 High Speed Steel and carefully heat treated, these tool bits are ground to ten popular, versatile shapes and ready for use. 86-543 0.250 2.500 0.04 86-569 0.312 2.500 0.07 86-593 0.375 3.000 0.12 Left-Hand Side Tool Made from M-2 High Speed Steel and carefully heat treated, these tool bits are ground to ten popular, versatile shapes and ready for use. 86-545 0.250 2.500 0.04 86-571 0.312 2.500 0.07 86-595 0.375 3.000 0.12 14-6
14 Square Nose Tool Made from M-2 High Speed Steel and carefully heat treated, these tool bits are ground to ten popular, versatile shapes and ready for use. 86-547 0.250 2.500 0.04 86-573 0.312 2.500 0.07 86-597 0.375 3.000 0.12 Rlght-Hand Side Tool Made from M-2 High Speed Steel and carefully heat treated, these tool bits are ground to ten popular, versatile shapes and ready for use. Product Slze, Length, Weight, 86-549 0.250 2.500 0.04 86-575 0.312 2.500 0.07 86-599 0.375 3.000 0.12 Brass Tool Made from M-2 High Speed Steel and carefully heat treated, these tool bits are ground to ten popular, versatile shapes and ready for use. 86-551 0.250 2.500 0.04 86-577 0.312 2.500 0.07 86-601 0.312 3.000 0.12 14-7 Always wear eye protection when near tools in use.
14 Set 86-605 Ground to Form Tool Bit Set Contents: One each of all ten 1/4" bits from previous page. In cardboard box. Approximate weight, 0.41 Ibs. Set 86-607 Ground to Form Tool Bit Set Contents: One each of all ten 5/16" bits from previous page. In cardboard box. Approximate weight, 0.65 Ibs. Set 86-608 Ground to Form Tool Bit Set Contents: One each of all ten 3/8" bits from previous page. In cardboard box. Approximate Weight, 1.12 lbs. Armaloy Ground Tool Bits and Cut-Off Blades Made from cast alloy steel, these bits and blades have a hardness between that of High Speed Steels and sintered Carbides. Ideal for either rough or finish cuts on steel, malleable iron, cast iron, non-ferrous metals, rubber, and plastics. Bits are furnished ready for grinding to final cutter shape; blades are bevelled, ground to shape and ready for use. Steel Analysis: 45-50% Cobalt, 27-32% Chromium, 14-19% Tungsten, 2-4% Carbon, 2-7% Tantalum, 1-3% Manganese, 2-5% Iron. Square Armaloy Tool Bits 86-651 0.250 2.125 0.04 86-653 0.312 2.500 0.08 86-655 0.312 3.000 0.13 86-659 0.500 4.000 0.31 Armaloy Cut-Off Blades 86-681 0.125 x 0.750 6.000 0.13 86-683 0.125 x 0.875 6.000 0.15 86-685 0.187 x 1.000 6.000 0.28 14-8
14 Armide Sintered Carbide, or Gray Red Enamel Shanks Armide Carbide-Tipped Cutters Armide is a sintered carbide material with a hardness approaching that of the diamond. It easily machines the toughest steels and castings and can be used also for hard rubber, plastics, and even glass. Since cutters will hold their edge far longer than even the finest tool steels, they will machine from ten to 100 times as many pieces before they require regrinding. Can be used in Armstrong Carbide Tool Holders and Quick Change Tool Holders, as well as other tool holding systems. Available in two popular grades, as described below. Grade A7-For light roughing and general finishing of steel. Red enamel shanks. Grade A5-For heavy roughing of steel. Red enamel shanks. Style AL, Grade A7 Straight Turning Tools For Turning, Facing, Boring, Chamfering 87-401 4 0.250 0.250 2.000 0.015 0.093 0.187 0.312 0.03 87-402 5 0.312 0.312 2.250 0.015 0.093 0.250 0.500 0.06 87-403 6 0.375 0.375 2.500 0.015 0.093 0.250 0.500 0.09 87-404 7 0.437 0.437 3.000 0.031 0.093 0.250 0.500 0.15 87-405 8 0.500 0.500 3.500 0.031 0.125 0.312 0.625 0.23 Style AR, Grade A7 Straight Turning Tools For Turning, Facing, Boring, Chamfering 87-421 4 0.250 0.250 2.000 0.015 0.093 0.187 0.312 0.03 87-422 5 0.312 0.312 2.250 0.015 0.093 0.250 0.500 0.06 87-423 6 0.375 0.375 2.500 0.015 0.093 0.250 0.500 0.09 87-424 7 0.437 0.437 3.000 0.015 0.093 0.250 0.500 0.15 87-425 8 0.500 0.500 3.500 0.031 0.125 0.312 0.625 0.23 Style AL, Grade A5 Straight Turning Tools For Turning, Facing, Boring, Chamfering 87-601 4 0.250 0.250 2.000 0.015 0.093 0.187 0.312 0.03 87-602 5 0.312 0.312 2.250 0.015 0.093 0.250 0.500 0.06 87-603 6 0.375 0.375 2.500 0.015 0.093 0.250 0.500 0.09 87-605 8 0.500 0.500 3.500 0.031 0.125 0.312 0.625 0.23 Style AR, Grade A5 Straight Turning Tools For Turning, Facing, Boring, Chamfering 87-621 4 0.250 0.250 2.000 0.015 0.093 0.187 0.312 0.03 87-622 5 0.312 0.312 2.250 0.015 0.093 0.250 0.500 0.06 87-623 6 0.375 0.375 2.500 0.015 0.093 0.250 0.500 0.09 87-624 7 0.437 0.437 3.000 0.031 0.093 0.250 0.500 0.15 87-625 8 0.500 0.500 3.500 0.031 0.125 0.312 0.625 0.23 14-9 Always wear eye protection when near tools in use.
14 Style BL, Grade A7 Lead Angle Turning Tools For Turning, Light Planing, Facing, Boring, Milling 87-441 4 0.250 0.250 2.000 0.015 0.093 0.187 0.312 0.03 87-442 5 0.312 0.312 2.250 0.015 0.093 0.250 0.500 0.06 87-443 6 0.375 0.375 2.500 0.015 0.093 0.250 0.500 0.09 87-444 7 0.437 0.437 3.000 0.031 0.093 0.250 0.500 0.15 Style BR, Grade A7 Lead Angle Turning Tools For Turning, Light Planing, Facing, Boring, Milling 87-461 4 0.250 0.250 2.000 0.015 0.093 0.187 0.312 0.03 87-462 5 0.312 0.312 2.250 0.015 0.093 0.187 0.500 0.06 87-463 6 0.375 0.375 2.500 0.015 0.093 0.187 0.500 0.09 87-464 7 0.437 0.437 3.000 0.031 0.093 0.187 0.500 0.15 87-465 8 0.500 0.500 3.500 0.031 0.125 0.312 0.625 0.22 Style C, Grade A7 Square Nose Tools For Forming, Grooving, Turning, Chamfering, Facing Product Size, Shank Dimensions (in) Blank Dimensions (in) Weight, Number Key A B C T W L lbs. 87-491 4 0.250 0.250 2.000 0.062 0.250 0.312 0.04 87-492 5 0.312 0.312 2.250 0.093 0.312 0.312 0.06 87-493 6 0.375 0.375 2.500 0.093 0.312 0.312 0.10 Style D, Grade A7 Point Nose, 80 Included Angle For Light Turning, Undercutting, Boring, Chamfering 87-521 4 0.250 0.250 2.000 0.015 0.015 0.240 0.312 0.04 87-522 5 0.312 0.312 2.250 0.015 0.093 0.302 0.375 0.06 87-523 6 0.375 0.375 2.500 0.015 0.093 0.365 0.500 0.10 14-10
14 Style D, Grade A5 Point Nose, 80 Included Angle For Light Turning, Undercutting, Boring, Chamfering 87-721 4 0.250 0.250 2.000 0.015 0.062 0.240 0.312 0.04 87-722 5 0.312 0.312 2.250 0.015 0.093 0.302 0.375 0.06 87-723 6 0.375 0.375 2.500 0.015 0.093 0.365 0.500 0.10 87-724 7 0.437 0.437 3.000 0.031 0.093 0.427 0.500 0.15 87-725 8 0.500 0.500 3.500 0.031 0.125 0.490 0.500 0.25 87-727 10 0.625 0.625 4.000 0.031 0.156 0.615 0.625 0.45 Style E, Grade A7 Neutral 60 Threading Tools For American Standard Threading Product Size, Shank Dimensions (in) Blank Dimensions (in) Weight, Number Key A B C T W L lbs. 87-551 4 0.250 0.250 2.000 0.062 0.240 0.312 0.04 87-552 5 0.312 0.312 2.250 0.093 0.302 0.375 0.06 87-553 6 0.375 0.375 2.500 0.093 0.365 0.500 0.10 Style E, Grade A5 Neutral 60 Threading Tools For American Standard Threading Product Size, Shank Dimensions (in) Blank Dimensions (in) Weight, Number Key A B C T W L lbs. 87-751 4 0.250 0.250 2.000 0.062 0.240 0.312 0.04 87-752 5 0.312 0.312 2.250 0.093 0.302 0.375 0.06 87-753 6 0.375 0.375 2.500 0.093 0.365 0.500 0.10 87-755 8 0.500 0.500 3.500 0.125 0.490 0.562 0.25 14-11 Always wear eye protection when near tools in use.