Sharma Resistors Page 1 Quick Reference Series Features Page CR Chip Type 0402-2512 Case Sizes 2 RS Carbon Composition 1/2 Watt 4
Sharma Resistors Page 2 CR THICK FILM CHIP RESISTOR SERIES INTRODUCTION The most popular type of chip resistor developed for surface mount technology. Ideal for general purpose applications. Unique construction and special termination techniques ensure high quality and reliability. Extremely compact size for miniaturization. FEATURES Excellent Long Term stability Available in Bulk and Tape & Reel packing. Available in Tolerances of ±5% & ±1% Uniform body size ensures compatibility with High Speed automatic handling machines Compatible with flow and re-flow soldering methods SPECIFICATIONS Resistance Range: 1 Ohm to 10 M Ohms for E24 values(5%) 1 Ohm to 1 M Ohms for E96 values(1%) Rated Power: 1/16 to 1W at 70 C (Please see Power Derating Curve) Rated Voltage: Rated Power x Nominal Resistance. Overload Voltage: Please refer to Power Ratings Table. Temperature Coefficient: ± 100 ppm or ± 200 ppm per C. Temperature Range: -55 C to +125 C with derating above 70 C Tolerance: ± 5% or ±1% (Special tolerance upon request.). Load Life: The component will be subjected to 1000 hours of testing at rated voltage and 70 C, with duty cycles of 1.5 hours ''on'' and 0.5 hours ''off''. After the test the Resistance change will remain within ±3% of the initial value + 0.1 Ohm for values above 1 M Ohm and 5% for values less than 1 M Ohm. Resistance to Soldering Heat: The component can be subjected to a soldering temperature of 270 C for 10 seconds. After the test the Resistance change will remain within ±3% + 0.1 Ohms. Case Dimensions Table Dimensions in mm Case Code L W T Max e 0402 1.0 + 0.05 0.5 + 0.05 0.35 + 0.05 0.25 + 0.15 0603 1.6 + 0.1 0.8 + 0.15 0.45 + 0.10 0.30 + 0.1 0805 2.0 + 0.1 1.25 + 0.10 0.55 + 0.10 0.40 + 0.2 1206 3.2 + 0.15 1.6 + 0.15 0.55 + 0.10 0.50 + 0.25 2010 5.0 + 0.15 2.5 + 0.15 0.55 + 0.15 0.60 + 0.2 2512 6.4 + 0.15 3.2 + 0.15 0.55 + 0.15 0.60 + 0.2 Power Derating Curve Tape, Reel and Packing Specifications Reel Dimensions; Reel Dimensions in Millimeters A B C D E W t ø178 ±2.0 ø50 min. 13.0 ±0.5 21.0 ±0.8 2.0 ±0.8 8.8/12.8 ±1.5 2.0 ±0.5 ø330 ±2.0 ø100 min. 13.0 ±0.5 21.0 ±0.8 2.0 ±0.8 8.8/12.8 ±1.5 2.0 ±0.6 Reel Dimensions in Inches A B C D E W t ø7 ±0.08 ø2.0 min. 5.0 ±0.02 0.83 ±0.03 0.08 ±0.3 0.35/0.50 ±0.06 0.08 ±0.02 ø13 ±0.08 ø4.0 min. 5.0 ±0.3 0.83 ±0.03 0.08 ±0.3 0.35/0.50 ±0.06 0.08 ±0.02 Power Ratings Table (Values above 10 M Ohms are available upon request) SIZE Rate Power Rate Current Maximum Maximum Temperature Combination of Resistance Operating at 70C of Jumper Working Overload Coefficient Range of Tolerance Temperature A Voltage Voltage of Resistance F (+1%) J (+ 5%) Range C Vw Vo ppm/c (E96) (E24) 0402 1/16 50 100 + 100 10 Ohms-562 K Ohms + 200 1 Ohm-9.76 Ohms 10 Ohms - 1 M Ohms 0603 1/10 1 50 100 + 100 10 Ohms-1 M Ohms + 200 1 Ohm - 9.76 Ohms 1 Ohm- 10 M Ohms 0805 1/8 150 300 + 100 10 Ohms - 1 M Ohms + 200 1 Ohm - 9.76 Ohms 1 Ohm - 10 M Ohms 1206 1/4 + 100 10 Ohms-1 M Ohms -55 - + 125 2 + 200 1 Ohm - 9.76 Ohms 1 Ohm - 10 M Ohms 2010 3/4 + 100 10 Ohms - 1 M Ohms 200 400 + 200 1 Ohm - 9.76 Ohms 1 Ohm - 10 M Ohms 2512 1 + 100 10 Ohms - 1 M Ohms + 200 1 Ohm - 9.76 Ohms 1 Ohm - 10 M Ohms
2.0 4.0 Sharma Resistors Page 3 Carrier Tape Dimensions; + 0.10 φ 1.5-0.0 ± 0.1 ± 0.1 E F W B Tmax A P A B W F E P Tmax SIZE ±0.2 mm or ±0.2 mm or ±0.3 mm or ±0.1 mm or ±0.1 mm or ±0.1 mm or CODE ±0.008'' ±0.008'' ±0.012'' ±0.004'' ±0.004'' ±0.004'' 0402 0.65 (0.026") 1.15 (0.045") 8.0mm (0.315") 3.5mm (0.138") 1.75mm (0.069") 2mm (0.079") 0.43mm (0.018") 0603 1.1 (0.043") 1.9mm (0.075") 8.0mm (0.315") 3.5mm (0.138") 1.75mm (0.069") 4mm (0.157") 0.60mm (0.024") 0805 1.65 (0.065") 2.4mm (0.094") 8.0mm (0.315") 3.5mm (0.138") 1.75mm (0.069") 4mm (0.157") 0.75mm (0.030") 1206 1.9 (0.075") 3.5mm (0.138") 8.0mm (0.315") 3.5mm (0.138") 1.75mm (0.069") 4mm (0.157") 0.75mm (0.030") 2010 2.8 (0.011") 5.6mm (0.22") 12.0mm (0.472") 5.5mm (0.217") 1.75mm (0.069") 4mm (0.157") 0.20mm (0.080") 2512 3.6 (0.142") 6.7mm (0.264") 12.0mm (0.472") 5.5mm (0.217") 1.75mm (0.069") 8mm (0.315") 0.20mm (0.080") Packing Methods; PACKING Paper Taping Reel (R) Embossed Taping Reel (K) Bulk Cassette (K) Style 7" (178mm) 10" (254mm) 13" (330mm) 7" (178mm) CR02 (0402) 10,000 10,000 10,000-50,000 CR03 (0603) 5,000 5,000 5,000-25,000 CR05 (0805) 5,000 5,000 5,000-10,000 CR06 (1206) 5,000 5,000 5,000-5,000 CR20 (2010) - - - 4,000 - CR25 (2512) - - - 4,000 - EIA Code-E24 Values EIA Code-E96 Values PART NUMBERING CR 10 11 33 36 10.0 10.2 14.7 15.0 21.5 22.1 31.6 32.4 46.4 47.5 68.1 69.8 12 39 10.5 15.4 22.6 33.2 48.7 71.5 Packaging: 13 43 10.7 15.8 23.2 34.0 49.9 73.2 Series: 1 = 5K Paper Taping 15 47 11.0 16.2 23.7 34.8 51.1 75.0 02 = 0402 3 or 4 Digit 2 = 10K Paper Taping 03 = 0603 EIA Code. 3 = 20K Paper Taping 16 51 11.3 16.5 24.3 35.7 52.3 76.8 05 = 0805 4 = 4K Plastic Taping 18 56 11.5 16.9 24.9 36.5 53.6 78.7 06 = 1206 Tolerance: Circuits: 5 = Loose Packing 20 62 11.8 17.4 25.5 37.4 54.9 80.6 20 = 2010 F = + 1% 0 = NA A = 5K Cassette 25 = 2512 G = + 2% 22 68 12.1 17.8 26.1 38.3 56.2 82.5 B = 10K Cassette J = + 5% C = 25K Cassette 24 75 12.4 18.2 26.7 39.2 57.6 84.5 D = 50K Cassette 27 82 12.7 18.7 27.4 40.2 59.0 86.6 30 91 13.0 19.1 28.0 41.2 60.4 88.7 Temp. Coefficient: Add 3 digit multipler 13.3 19.6 28.7 42.2 61.9 90.9 0 = + 100 ppm/c Examples: 13.7 20.0 29.4 43.2 63.4 93.1 3 = + 200 ppm/c 101= 100 Ohms 14.0 20.5 30.1 44.2 64.9 95.3 472= 4.7K Ohms 14.3 21.0 30.9 45.3 66.5 97.6 684= 680K Ohms Add 4 digit multipler 1R0= 1 Ohm Examples: 15R= 15 Ohms 1130= 113 Ohms 1871= 1.87K Ohms Note: 6193= 619K Ohms R= decimal point in 19R1= 19.1 Ohms Tel: (949)642-7324 the EIA code 1R21= 1.21 Ohms SECI Engineers & Buyers' Guide Fax: (949)642-7327
Sharma Resistors Page 4 THE FIXED CARBON COMPOSITION RESISTORS 1. Dimensions d W L W D 2. Rating and Dimensions Dimensions in mm Rated Power Type (W) L D W d Max Rated Voltage v Max Overload Voltage v Resistance range RS11-1/2 0.5 9. 5 0.8 3. 5 0.2 26 2 0.69 0.01 350 500 4.7 to 22M 3. Sold Resistance in Packs 1/2WATT SHARMA Type # SHARMA Type # SHARMAType # SHARMA Type # RS11-1/2W-4R7 4.7 RS11-1/2W-18 18 RS11-1/2W-75 75 RS11-1/2W-300 300 RS11-1/2W-5R1 5.1 RS11-1/2W-20 20 RS11-1/2W-82 82 RS11-1/2W-330 330 RS11-1/2W5R6 5.6 RS11-1/2W-22 22 RS11-1/2W-91 91 RS11-1/2W-360 360 RS11-1/2W-6R2 6.2 RS11-1/2W-24 24 RS11-1/2W-100 100 RS11-1/2W-390 390 RS11-1/2W-6R8 6.8 RS11-1/2W-27 27 RS11-1/2W-110 110 RS11-1/2W-430 430 RS11-1/2W-7R5 7.5 RS11-1/2W-30 30 RS11-1/2W-120 120 RS11-1/2W-470 470 RS11-1/2W-8R2 8.2 RS11-1/2W-33 33 RS11-1/2W-130 130 RS11-1/2W-510 510 RS11-1/2W-9R1 9.1 RS11-1/2W-36 36 RS11-1/2W-150 150 RS11-1/2W-560 560 RS11-1/2W-10 10 RS11-1/2W-39 39 RS11-1/2W-160 160 RS11-1/2W-620 620 RS11-1/2W-11 11 RS11-1/2W-43 43 RS11-1/2W-180 180 RS11-1/2W-680 680 RS11-1/2W-12 12 RS11-1/2W-47 47 RS11-1/2W-200 200 RS11-1/2W-750 750 RS11-1/2W-13 13 RS11-1/2W-51 51 RS11-1/2W-220 220 RS11-1/2W-820 820 RS11-1/2W-15 15 RS11-1/2W-62 62 RS11-1/2W-240 240 RS11-1/2W-910 910 RS11-1/2W-16 16 RS11-1/2W-68 68 RS11-1/2W-270 270 RS11-1/2W-1K 1.0K
Sharma Resistors Page 5 1/2WATT Cont. SHEET:1 OF 6 SHARMAType# SHARMA Type # SHARMA Type # SHARMA Type # RS11-1/2W-1K1 1.1K RS11-1/2W-13K 13K RS11-1/2W-160K 160K RS11-1/2W-2M 2.0M RS11-1/2W-1K2 1.2K RS11-1/2W-15K 15K RS11-1/2W-180K 180K RS11-1/2W-2M2 2.2M RS11-1/2W-1K3 1.3K RS11-1/2W-16K 16K RS11-1/2W-200K 200K RS11-1/2W-2M4 2.4M RS11-1/2W-1K5 1.5K RS11-1/2W-18K 18K RS11-1/2W-220K 220K RS11-1/2W-2M7 2.7M RS11-1/2W-1K6 1.6K RS11-1/2W-20K 20K RS11-1/2W-240K 240K RS11-1/2W-3M0 3.0M RS11-1/2W-1K8 1.8K RS11-1/2W-22K 22K RS11-1/2W-270K 270K RS11-1/2W-3M3 3.3M RS11-1/2W-2K 2.0K RS11-1/2W-24K 24K RS11-1/2W-300K 300K RS11-1/2W-3M6 3.6M RS11-1/2W-2K2 2.2K RS11-1/2W-27K 27K RS11-1/2W-330K 330K RS11-1/2W-3M9 3.9M RS11-1/2W-2K4 2.4K RS11-1/2W-30K 30K RS11-1/2W-360K 360K RS11-1/2W-4M3 4.3M RS11-1/2W-2K7 2.7K RS11-1/2W-33K 33K RS11-1/2W-390K 390K RS11-1/2W-4M7 4.7M RS11-1/2W-3K 3.0K RS11-1/2W-36K 36K RS11-1/2W-430K 430K RS11-1/2W-5M1 5.1M RS11-1/2W-3K3 3.3K RS11-1/2W-39K 39K RS11-1/2W-470K 470K RS11-1/2W-5M6 5.6M RS11-1/2W-3K6 3.6K RS11-1/2W-43K 43K RS11-1/2W-510K 510K RS11-1/2W-6M2 6.2M RS11-1/2W-3K9 3.9K RS11-1/2W-47K 47K RS11-1/2W-560K 560K RS11-1/2W-6M8 6.8M RS11-1/2W-4K3 4.3K RS11-1/2W-51K 51K RS11-1/2W-620K 620K RS11-1/2W-7M5 7.5M RS11-1/2W-4K7 4.7K RS11-1/2W-56K 56K RS11-1/2W-680K 680K RS11-1/2W-8M2 8.2M RS11-1/2W-5K1 5.1K RS11-1/2W-62K 62K RS11-1/2W-750K 750K RS11-1/2W-9M1 9.1M RS11-1/2W-5K6 5.6K RS11-1/2W-68K 68K RS11-1/2W-820K 820K RS11-1/2W-10M 10M RS11-1/2W-6K2 6.2K RS11-1/2W-75K 75K RS11-1/2W-910K 910K RS11-1/2W-11M 11M RS11-1/2W-6K8 6.8K RS11-1/2W-82K 82K RS11-1/2W-1M 1.0M RS11-1/2W-12M 12M RS11-1/2W-7K5 7.5K RS11-1/2W-91K 91K RS11-1/2W-1M1 1.1M RS11-1/2W-13M 13M RS11-1/2W-8K2 8.2K RS11-1/2W-100K 100K RS11-1/2W-1M2 1.2M RS11-1/2W-15M 15M RS11-1/2W-9K1 9.1K RS11-1/2W-110K 110K RS11-1/2W-1M3 1.3M RS11-1/2W-16M 16M RS11-1/2W-10K 10K RS11-1/2W-120K 120K RS11-1/2W-1M5 1.5M RS11-1/2W-18M 18M RS11-1/2W-11K 11K RS11-1/2W-130K 130K RS11-1/2W-1M6 1.6M RS11-1/2W-20M 20M RS11-1/2W-12K 12K RS11-1/2W-150K 150K RS11-1/2W-1M8 1.8M RS11-1/2W-22M 22M 4. Part Numbering System Example: RS11 1/2W 2k7 J T type Rated Power W Normal Resistance Resistance Tolerance Packaging RS11 0.5W 2k7=2.7k J = 5% K= 10% M= 20% B T Bulk Tape &Reel
Sharma Resistors Page 6 5. Derating Curve Rated Load P / P R % 70 125 100 80 60 40 20-55 -40-20 0 20 40 60 80 100 120 Temperature 6. Resistance Temperature Characteristics Max. Resistance Characteristics Resistance range ( R*/R)% Temperature range Temperature range -55 to +20 +20 to +125 1k and under 6.5 6.5 1.1k to 10k 10 8 11k to 100k 13 10 110k to 1M 15 13 1.1M to 10M 20 19.5 11M and over 25 19.5 * R=R 2 -R 1 R 1 Resistance value at reference temperature Resistance value at test temperature R 2 7. Mechanical and Electronic Performance Description Test method Performance Requirements Frequency range: 10HZ ~ 500Hz No visible damage Vibration Amplitude: 0.75mm Total last tine: 6h R 2%R+0.1.
Sharma Resistors Page 7 8. Mechanical and Electronic Performance Cont. Description Test method Performance Requirements Pull Along the longitudinal axis of the terminal leads 20N, 5S Terminal Strength Bending two times Once in each No visible damage Bending direction R 2%R+0.1. Twist Twist 180 two times Resistance to Soldering Heat Solder temperature: 350 10 Immerge time : 3.5 0.5S Depth from the body of the resistor: 2 +0.5 mm No visible damage R 2%R+0.1. Solderability Solder temperature : 235 5 Dwell time in solder: 3 0.5S Depth from the body of the sesistor: 2 0.5 mm At least 95% of the dipping surface must be covered by new solder no flaws gathered Voltage Coefficient (Application in 1K to 10M ) Use 10%Resistance rated voltage and 100%Resistance rated voltage to test resistance value A total resistance change of 2% max. or 0.035%/V Short time overload 2.5 times of rated voltage or times of Max. rated voltage (selecting lower ) 5S. No visible damage R 2%R+0.1 Dielectric withstanding voltage Resistois shall be clamped in the trough of a 90 metallic V-block and shall be tested at AC potential respectively Specified in the above list for 60 5s No evidence of arcing or insulation breakdown
Sharma Resistors Page 8 9. Mechanical and Electronic Performance Cont. Description Test method Performance Requirements A -55 Temperature fast B +125 No visible damage change Shape check Resistance R 2%R+0.1. Last out time : 1000h When 48h 500h and 1000h check: 70 endurance Shape check resistance When 1000h check: Insulation Resistance No visible damage Mark clarity R 10%R+0.5 R 1G Fixing state Damp heat Shape check Resistance Insulation Resistance No visible damage Mark clarity R 10%R+0.5 R 100M 10. Taping production Length from the end 2.0mm Tape Width T Lead Bending 0.8mm From Center 0.5mm Pitch P Lead Overlap 1.0mm Max L 1 L 2 Tape inner width W Tape overlap 1.0 e external width w
Sharma Resistors Page 9 Tape Style Taping Dimensions mm W A T P L1-L2 T-52 52 1.0 64.5 0.5 6.0 1.0 5.0 0.3 0 1.0 SHEET 11. Products Package a. In bulk Description Specification Quantity Dimension (mm Length Width Height Thickness Small-size plastic bag 1/2 W 100 pieces 115 75 0.075±0.005 Big-size plastic bag 1/2 W 5 bags 175 115 0.025±0.005 Paper box 1/2 W 20 boxes 310 200 120 3 Outside package 1/2 W 3 Paper boxes 410 +10 330 +10 220 +10 4 Note: Outside package weight 15±1 kg b. Taping Products Description Specification Quantity Dimension mm Length Width Height Thickness Paper box 1/2 W 2000 pieces 445 80 65 2 Outside package 1/2 W 10 Paper boxes 460 +10 420 +10 150 +10 4 Note: Outside package weight 10±1 kg