Take a really good look

Take a really good look Telescopic Trailer Tow Mirror by Installation Instructions & Information Manual To suit GM / CHEVY / CADILLAC (GMT800) vehicle model years: 1999 2007 Silverado, Sierra 2000 2006 Suburban, Tahoe, Yukon, Avalanche 2002 2006 Avalanche, Escalade take a really good look Part # 1440351 Version # C Issued Sept. 06 Congratulations on choosing the Telescopic Trailer Tow Mirror by Schefenacker! Made by the world s largest manufacturer of exterior mirrors, the Telescopic Trailer Tow Mirror combines great looking aerodynamic styling with the toughness only a company like Schefenacker can produce. You ve chosen one of the hottest new products in the past few years! Its interchangeable covers mean you can personalize the looks that suit you and your pick up, and a wide range of options mean you can have the right equipment for the right job. WARNING Schefenacker recommends that this installation be carried out by a professional installer. Please read ALL the instructions and warnings thoroughly before installing the Telescopic Trailer Tow Mirrors. These mirrors are designed only for the vehicles listed on this page. Ensure that the fitting instructions are followed exactly, as failure to do so may result in incorrect installation, and may also result in the driver, passengers and vehicle being placed in hazardous conditions. PARTS LIST 1 LH Mirror 1 RH Mirror Installation Instructions 6 x M6 Nut Washers (Gold) 2 x Gaskets Driver side mirror Passenger side mirror

Important Information Schefenacker Warranty Terms & Conditions Schefenacker warrants that this mirror is free from defects in material and workmanship under normal use for a period of three years from the date of purchase. Our liability under this warranty is limited to the replacement or repair of the mirror which must be returned, transportation pre-paid, to Schefenacker with the sales receipt. Warranty will only apply if the mirror is installed and used in accordance with the factory directions which accompany the mirror. Under no circumstances is Schefenacker liable for any direct or indirect loss or damage (including consequential loss or damage). This warranty does not apply to defects or damage resulting from incorrect installation or alteration, nor does it apply to any mirror which has been subject to abuse, misuse or negligence. Schefenacker does not cover damage caused by automated car washes. Whilst we recommend that both the driver and passenger mirrors are folded parallel to the vehicle door when entering an automated car wash, we also recommend that you speak with the operator of the car wash to determine whether your vehicle should be sent through. Contact Schefenacker either by phone, fax, or email and advise that you believe there is a problem with your mirror: Phone: 877-888-6472 (toll free), Fax: 734-721-7388, Email: sales@ttt-mirror.com Important: Schefenacker recommends that you do not dispose of your factory fitted mirrors. Schefenacker will only replace/repair defective product if inspected by them. By keeping your factory fitted mirrors, you can re-install them in the event of a warrantable situation. It is against the law to operate your vehicle without exterior mirrors. Your new Telescopic Trailer Tow Mirrors by Schefenacker have a range of replacement parts that are available from your Schefenacker dealer or from our website at www.ttt-mirror.com If accidntal damage occurs, the mirrors can be purchased individually. Replacement Parts Other Models Available Replacement main glass, wide-angle spotter, custom paintable covers, custom theme covers, and LED light assemblies are some of the components available. Check with your Schefenacker dealer or the web site for availability and suitability. MODEL ELECTRIC ELECTRIC MAKE YEAR TYPE MANUAL & HEAT* & HEAT & LIGHTS* FORD 2004 - curr F150 3 3 3 1997-2003 F150 ƒ 3 3 3 1998-2000 F250 LD 3 3 3 LINCOLN 2005 - curr MARK LT 3 3 3 CHEVY 1999-2007 SILVERADO 3 3 = 3 = 2000-2006 SUBURBAN 3 3 = 3 = 2000-2006 TAHOE 3 3 = 3 = 2002-2006 AVALANCHE 3 3 = 3 = MODEL ELECTRIC ELECTRIC MAKE YEAR TYPE MANUAL & HEAT* & HEAT & LIGHTS* GMC 2000-2006 YUKON 3 3 = 3 = 1999-2007 SIERRA 3 3 = 3 = CADILLAC 2002-2006 ESCALADE 3 3 = 3 = DODGE 2002 - curr RAM 3 3 3 * If you currently have manual mirrors, the mirror kit will not retrofit the vehicle to have electric mirrors. ƒ Will not fit F150 SuperCrew (4 door) vehicles. = Multiplex Kit (part # 1090) is required if your vehicle is model year 2003 onwards. Fits Dodge Ram 1/2 ton (1500) from MY 2002 onwards, and 3/4 ton (2500) and 1 ton (3500) from MY 2003 onwards. Fits new body style only. Customer Support Should you need technical assistance during the installation, you should firstly contact your point of purchase.

PREPARATION The tools required for fitting are all readily available, off-the-shelf items: Manual mirrors: Socket drive handle 10 mm socket Electric & Heat mirrors: 1 roll of electrical tape Socket drive handle 8 mm socket 10 mm socket Small straight slotted screwdriver 7 mm socket 1 Set of multiplex harnesses (Sold separately, for MY 2003 onwards vehicles only) Electric, Heat & Lights mirror variants only: Feeder tube (fish wire, coat hanger) - 2 feet 1 Set of multiplex harnesses (Sold separately, for MY 2003 onwards vehicles only) 2 x 20 gauge yellow extension wires 6 feet & 12 feet long each. (For MY 2003 vehicles only) OR 2 x 6 feet long only (for pre MY 2003 vehicles only) 1 x 20 gauge 6 foot long red extension wire (For pre MY 2003 vehicles only) 1 x 20 gauge 12 foot long red extension wire (For pre MY 2003 vehicles only) 1 Roll of electrical tape 6 mm socket 7 mm socket 8 mm socket 10 mm socket Box cutter Wire cutters Socket drive handle Small straight slotted screwdriver Socket drive extension Upgrading to Heat, Turn Signal & Clearance Light footnote: You can install a TTT mirror with the above features if your factory fit mirror did not have them. Note: You cannot upgrade to electric mirrors if you currently have manual mirrors.

Important Information Electrical Information Light Module (Turn Signal/Clearance Light): Voltage Range Nominal Voltage Requirement Current Draw @ 13.8 volts Glass Actuator: Maximum Current (operation) Maximum Current (over-ride) Voltage Range Heater: Maximum Current Draw (-40ºC) Voltage Range 9.5 to 14.6 volts 13.8 volts Clearance: 35 to 55 ma Turn: 70 to 110 ma 300 ma 400 ma 9 to 16 volts 5.0 A No Limit Main Mirror Harness Connector: Connector Detail 1 2 3 4 12 11 LEFT/RIGHT HAND PURPLE BROWN GREEN BLUE MOTOR UP + MOTOR DOWN + MOTOR IN + MOTOR OUT + 5 8 6 7 LEFT HAND DRIVERS # Color Description 1 GREEN MOTOR IN 2 NOT USED 3 NOT USED 4 BLACK LIGHT MODULE/ HEATER EARTH 5 BROWN MOTOR DOWN 6 PURPLE MOTOR UP 6 BLUE MOTOR OUT 7 NOT USED 8 WHITE HEATER POWER 9 NOT USED 10 NOT USED 11 RED TURN INDICATOR SIGNAL 12 YELLOW FRONT CLEARANCE LIGHT RIGHT HAND PASSENGERS # Color Description 1 BLUE MOTOR OUT 2 NOT USED 3 NOT USED 4 BLACK LIGHT MODULE/ HEATER EARTH 5 BROWN MOTOR DOWN 6 PURPLE MOTOR UP 6 GREEN MOTOR IN 7 NOT USED 8 WHITE HEATER POWER 9 NOT USED 10 NOT USED 11 RED TURN INDICATOR SIGNAL 12 YELLOW FRONT CLEARANCE LIGHT

Important Information Post MY 2003 Multiplex harness connectors (left/drivers side): Blue Control Module Black Control Module Black mirror to vehicle connector 1. MOTOR DOWN 2. MOTOR IN 3. MOTOR UP/MOTOR OUT 4. HEATER POWER 5. GROUND/EARTH 6. TURN SIGNAL 7. MOTOR IN 8. GROUND/EARTH 9. MOTOR DOWN 10. MOTOR UP/MOTOR OUT 11. HEATER POWER Post MY 2003 Multiplex harness connectors (right/passenger side): Blue Control Module Connector Black mirror to vehicle connector 1. TURN SIGNAL 2. GROUND/EARTH 3. HEATER POWER 4. MOTOR DOWN 5. MOTOR UP/MOTOR IN 6. MOTOR OUT 7. GROUND/EARTH 8. HEATER POWER 9. MOTOR DOWN 10. MOTOR UP/MOTOR IN 11. MOTOR OUT Mirror cover removal: The polished black cover on each mirror can be removed and painted to match the vehicle's body color, or replaced with chrome (p/n 9040) or 'USA Flag' theme covers (p/n 9060). Find below the removal/installation instructions for the covers. Existing cover removal. Make sure you have the required tools: flashlight slotted screwdriver (with at least a 5 shaft). Approximate installation time: 5 10 minutes. 1. Pull the top edge of the main glass as far forward as practical. It may make a clicking sound as it moves - this is normal. (See Figure 1a) Using a flashlight, locate the vertical rectangular slot on the vehicle side of the main glass opening. It will be alongside a hex-head screw and another rectangular slot - horizontal. (See Figure 1b) Continued over page Figure 1a Figure 1b Vertical slot Hex-head Screw Horizontal slot

2. Insert your screwdriver through the vertical slot until you feel the tip pressing against a spring loaded clip (see Figure 2 opposite). Push the screwdriver gently against the clip very little force is needed. Important Information Figure 2 3. At the same time, slide the mirror cover towards the vehicle door. (see Figure 3 opposite) The cover should slide away from the main body of the mirror. Figure 3 4. To refit the cover, simply position the cover over the main body of the mirror, locate the two hook-like tags in the slots at the top edge of the mirror body, place the cover flat against the body of the mirror and slide the cover away from the vehicle door. (see Figure 4 opposite) You should hear a definite click as the cover locates itself. Check for an even and secure fit of the cover. Figure 4

STEPS 1, 2, 3 & 4 STEP 1 Roll both front windows completely down and then disconnect the vehicles battery. Read all instructions before proceeding to STEP 2. NOTE: If you are installing a manual mirror do not disconnect the battery. STEP 2 Remove door rear upper trim panel. The panel is held by two clips located in a vertical line down the center of the part. It can be removed by pulling the top corner of the panel rearward. Pull here NOTE: Start with LH (driver s side) door. STEP 3 Remove the gasket to reveal three nuts which are used to hold the mirror to the door. Gasket NOTE: If you are installing a manual mirror variant, proceed to STEP 17. Pre MY 2003 If you are replacing electric (heated factory fit mirrors with P/N 1010 (electric/heated TTT mirrors), unplug the mirror from the vehicle wiring loom, then proceed to STEP 17. STEP 4 Remove door console switch module. This module is located by clips and can be removed by prying up gently at the two slots located on the bottom edge of the module. Slots NOTE: If the two clips remain in the trim after removal, they need to be replaced into the module for re-assembly.

STEPS 5, 6, & 7 STEP 5 Unplug all connectors from door console switch module. Connectors STEP 6 Remove the door handle surround panel. The surround is located by a number of clips at the rear of the part and a tongue at the front. The part can be removed, by pulling the rear of the part away from the door, and then sliding the part towards the front of the door. Pull here STEP 7 Remove the 7 mm bolt. 7 mm bolt POST MY 2004 If present, remove cap and screw on the outer edge of the door trim, and the clip on the inner edge of the door trim. Screw cap Screw Cap Door trim outer edge Inner edge

STEPS 8, 9, 10 & 11 STEP 8 Remove door lock slide by gently prying the back of the slide outwards (with a small straight slotted screwdriver) and away from the door. Door lock slide STEP 9 MY 2003 ONWARDS ONLY Remove the 7 mm screw from the door lock slide area. 7 mm screw STEP 10 Remove the 7 mm screw from the door handle. 7 mm screw STEP 11 Using 2 hands pull up on the door inner trim panel being careful not to completely remove it from the door, until all connectors are removed from behind the trim panel. (Refer to Steps 12 & 13 below) Pull upwards

STEPS 12, 13, 14, & 15 STEP 12 Unplug the speaker and memory connector if equipped. Memory connector Speaker connector STEP 13 Remove the door light by gently pulling the light connector away from the trim panel. Light connector STEP 14 MY 2003 ONWARDS ONLY Turn trim panel upside down for easier access to all connectors. Unplug all connectors from door console switch module. NOTE: Connector A has a small latch that needs to be depressed with a small screw driver and then the gray lever moved to the side. Connector A Remove trim panel from the door once all connectors have been removed and put to one side. STEP 15 Unplug mirror connector from vehicle wiring loom. Mirror connector

STEPS 16, 17, 18 & 19 STEP 16 Pull back top right hand corner of plastic lining. MY 2003 ONWARDS ONLY The mirror harness is attached to the door sheet metal by three clips. Remove the harness by removing the black tape attaching the harness to the clips. Clips NOTE: Do not attempt to remove the clips from the door as damage may result. STEP 17 Undo the three nuts which were exposed in step 3. Nuts Note: the mirror must be supported while the last nut is removed. If this is not done the mirror may fall from the door and be damaged. The nuts can be removed by using a 10 mm hex socket drive. STEP 18 Remove the mirror from the door by pulling the mirror directly away from the outer panel. Pull loom free The loom must be pulled out of the door panel taking care to not let it catch on any of the door structure. If this occurs the loom can be freed by feeding it in and out until the loom is no longer caught. STEP 19 Fit the foam gasket supplied in the installation kit to the base of the new mirror. Install the new mirror to the door. Feed the wire harness through the center hole in the door (if you are installing the electric mirror type). Slide mirror onto the door and attach with nuts supplied. NOTE: Repeat STEPS 2 to 19 for the RH mirror. NOTE: If you are installing manual mirrors, and you have completed the above steps for both RH & LH mirrors, then the installation is now complete, proceed to STEP 36. PRE MY 2003 NOTE: If you are replacing electric/heated factory fit mirrors with P/N 1010 (electric/heated TTT mirrors), and you have completed the above steps for both RH & LH mirrors, then the installation is now complete, please proceed to STEP 36.

STEPS 20, 21, 22 & 23 STEP 20 MY 2003 ONWARDS ONLY Attach LH (driver s side) MY2003 + Multiplex harness Adaptor to the LH mirror connector as shown. The LH Multiplex harness is indicated by a red label and the right Multiplex harness by a white label. Splice together the free red wire from the mirror harness with the free red wire on the Multiplex harness. (Only if you are installing a mirror with lights). Note: For non-lighted mirrors, the red wire from the Multiplex harness can be removed. Feed the mirror harness into the door and attach to three clips on the door, using electrical tape. NOTE: Repeat STEP 20 for the RH (passenger s) mirror. NOTE: If you are installing an electric with heat mirror variant, your installation is now complete. Proceed to STEP 36. Pull seal panel here TURN SIGNAL & CLEARANCE LIGHT UPGRADE STEP 21 Pull up seal panel from the front edge, until 2 clips disengage. NOTE: You do not need to fully remove the seal panel. STEP 22 Press the foot brake pedal as far as it will go. Pull kick panel here Remove the side kick panel, by pulling the top corner in the rear direction. STEP 23 Remove the fuse panel cover by lifting the bottom edge upwards. NOTE: If installing on a post MY 2003 vehicle, this step is for the LH (driver s side) mirror only. Lift fuse panel cover here

STEPS 24, 25, 26 & 27 STEP 24 Remove the door speaker by pushing down on the latch and pulling the speaker away from the door. Push latch here STEP 25 Remove the door side grommet at the vehicle body side only, by inserting a straight slotted screw driver between the grommet and the vehicle body, at the ribbed section of the grommet. NOTE: There is a white plastic insert inside the grommet, this must be removed with the grommet. DO NOT remove the grommet from the plastic insert. Grommet (rib) STEP 26 Feed the feeder tube through the speaker hole and into the convoluted tube of the door side grommet. Feeder STEP 27 MY 2003 ONWARDS ONLY Using electrical tape, attach the yellow extension wire to the feeder tube at the vehicle body end. Then pull the feeder tube back through the convoluted grommet. Tape on feeder NOTE: Use 6 ft of yellow wire on the LH (driver s) side and 12 ft of yellow wire on the RH (passenger s) side.

STEPS 28, & 29 STEP 28 Feeder tube Using electrical tape, attach the yellow and red wires to the feeder tube at the vehicle body end. Then pull the feeder tube back through the convoluted grommet. NOTE: Use 6ft of yellow wire on the LH (driver s) side and 6ft of yellow wire on the RH (passenger s) side. NOTE: Use 6ft of red wire on the LH (driver s) side and 12ft of red wire on the RH (passenger s) side. STEP 29 Feed one end of the yellow extension wire into the vehicles body and feed it up to and in front of the fuse panel. NOTE: For pre MY 2003 vehicles feed both the red & yellow extension wires into the vehicles body. For the RH passenger s side, feed the yellow wire in front of the passenger s side fuse panel. RH wire MY 2003 onwards For the RH passenger s side mirror, feed the yellow wire all the way under the dash up to where the LH wire protrudes out in front of the driver s side fuse panel. Feed the other end of the yellow and red extension wires up through the inside of the door. Tape the wires to the door to keep them away from the moving parts inside the door. NOTE: You will only have a red extension wire if you are installing on a pre MY 2003 Vehicle. Connect the yellow extension wire to the yellow wire on the mirror harness. LH wire Tape Attach the loose red wire from the new mirror to the red extension wire that you fed up into the door in the steps above. NOTE: Repeat appropriate STEPS from 21 to 29 for the RH (passenger s side) mirror.

STEP 30 STEP 30 MY 2003 ONWARDS ONLY Tilt steering wheel all the way down. Tilt down Put key into the ignition and turn to Ignition on, depress brake pedal and move the gear lever all the way down (1st gear). Remove the dash panel by pulling it to the rear direction starting at the top LH corner. Pull dash panel here Remove light switch assembly by de-latching 3 clips with a straight edge screwdriver and pulling out. 3 clips Attach both yellow wires from the mirror harnesses to the brown with white trace wire in the back of the switch assembly. Brown with white trace wire

STEPS 31 & 32 STEP 31 Attach the LH (driver side) mirror yellow wire to the single brown wire in location number 5 of the orange connector. You will find this orange connector at the drivers side fuse panel. See drawing below for wire location numbers in the orange connector. Location #5: single brown wire NOTE: There are two locations with brown wires. Do not attach to the location with two brown wires, location number 6. 1 2 3 4 5 6 7 8 9 10 11 12 Attach yellow wire here Problems with Installation - steps 31 and 32. Mirror Affected GMC/CHEVEY 1020 Problem: The driver side fuse panel has only one brown wire instead of two brown wires in position six. Solution: This detail can be overlooked. Complete steps 31 & 32. STEP 32 Attach the RH (passenger side) mirror yellow wire to the brown wire in location number 12 of the orange connector. You will find this orange connector at the passenger side fuse panel. See drawing below for wire location numbers in the orange connector. two brown wires: DO NOT USE Location #12: single brown wire 1 2 3 4 5 6 Attach yellow wire here 7 8 9 10 11 12 Problem: On the passenger side fuse panel, there may be no orange connector, hence no place to connect the passenger side mirror yellow wire. Solution: The yellow wire operates the clearance light function on the mirror, so this needs to be wired into a suitable vehicle circuit. Extend the yellow wire so that it has enough length to wire into the circuit as identified in STEP 31. This means that the yellow wire from both mirrors will be wired into the same circuit.

STEPS 33, 34 & 35 STEP 33 Remove two 7 mm bolts. Two 7 mm bolts STEP 34 Loosen the dash panel to get access for removal of the hush panel. There is no need to completely remove it. Pull dash panel here Remove the hush panel from the dash. It is attached by two clips on the top edge. Pull the hush panel in a rearwards direction. Clips underneath. Pull rearwards

STEPS 35 & 36 STEP 35 Attach the LH (driver s side) mirror red wire to the light blue wire in location 6 on the brown connector found under the dash. It is the left most connector in a row of three connectors. See connector wire location diagram below. Light blue wire Dark blue wire Feed the RH (passenger s side) mirror red wire under the dash and attach it to the dark blue wire in location 7 on the same connector as above. NOTE: There are more than one dark and light blue wires in this connector, so make sure you use locations 6 & 7 as described above. 1 2 3 4 5 6 7 8 9 10 11 12 Brown connector Attach LH (driver s) red wire to light blue wire here Attach RH (driver s) red wire to dark blue wire here 13 14 15 16 17 18 19 20 21 22 23 24 Step 36 PRE AND POST MY 2003 Your installation is now complete. Reverse the appropriate steps to reassemble your vehicle. HEATED GLASS UPGRADE: If your vehicle is not equipped with factory fit heated mirrors and you would like to upgrade to this feature, please follow the following instructions: If your vehicle is equipped with a defogger on the rear window, the mirror heater circuit already exists in the vehicle s mirror harness. To activate your TTT mirrors, simply press the defogger switch (located near your vehicle s climate control on the dash panel). If your vehicle is not equipped with a defogger on the rear window, you will need to cut the white wire from the driver s and passenger s side mirror connectors, and then connect 6 feet of wire to the driver s side white wire, and 12 feet of wire to the passenger's side white wire. Both of these driver and passenger side wires will then need to be attached to the wire in location number 2 (referred to in Step 35). Once complete, this will mean the heated glass will remain constantly on when the vehicle s ignition is on. NOTE: MY 2003 ONWARDS ONLY Note: If your vehicle was fitted with memory mirrors, it is recommended that they are disabled once you fit the TTT mirrors to your vehicle. This is because the mirror will incorrectly adjust the position of the main glass when the memory function is used, and will then need to be re-adjusted back to its correct position. To avoid this from happening, you will need to disable the Seat Position Recall and Curb View Assist functions. Refer to the Driver Information Centre (DIC) section in your vehicle s owner manual. Please also note, that when operating the preset memory function by pushing the buttons on the driver s side door, the position of the main glass may move. If you use this function, you may need to re-adjust the main glass prior to driving the vehicle.