Flow Calculations for the V-Cone and Wafer-Cone Flowmeters

Similar documents
Advanced Differential Pressure Flowmeter Technology V-CONE FLOW METER TECHNICAL BRIEF

HW 2. Q v. kt Step 1: Calculate N using one of two equivalent methods. Problem 4.2. a. To Find:

The Concept of the Effective Mass Tensor in GR. The Equation of Motion

The Mathematics of Pumping Water

A Gas Law And Absolute Zero

The Velocities of Gas Molecules

FLOW MEASUREMENT 2001 INTERNATIONAL CONFERENCE DERIVATION OF AN EXPANSIBILITY FACTOR FOR THE V-CONE METER

A Gas Law And Absolute Zero Lab 11

CONTROL VALVE PRESSURE DROP AND SIZING

Pump Formulas Imperial and SI Units

Calculation of flow rate from differential pressure devices orifice plates

Equivalents & Conversion Factors 406 Capacity Formulas for Steam Loads 407 Formulas for Control Valve Sizing

Comparison of Gamma and Passive Neutron Non-Destructive Assay Total Measurement Uncertainty Using the High Efficiency Neutron Counter

Prediction of Pressure Drop in Chilled Water Piping System Using Theoretical and CFD Analysis

An online sulfur monitoring system can improve process balance sheets

PREDICTION OF MILKLINE FILL AND TRANSITION FROM STRATIFIED TO SLUG FLOW

OUTCOME 3 TUTORIAL 3 - THE FLOW OF REAL FLUIDS

Michael Montgomery Marketing Product Manager Rosemount Inc. Russ Evans Manager of Engineering and Design Rosemount Inc.

Weirs for Flow Measurement

2 1/2 Pipe. 40 = height. the gauge pressure inside the vessel from the gauge pressure at the nozzle inlet as shown:

More Unit Conversion Examples

Exergy Calculation. 3.1 Definition of exergy. 3.2 Exergy calculations Exergy of environment air

CO MPa (abs) 20 C

Fluid Mechanics: Static s Kinematics Dynamics Fluid

Spreadsheet Program for EPA Method 202 Condensible Particulate Matter Emission Rate and Concentration Calculations

SIMPLIFIED METHOD FOR ESTIMATING THE FLIGHT PERFORMANCE OF A HOBBY ROCKET

Piping Hydraulic Line Design and Sizing Software KLM Technology Group

Homework 8. problems: 10.40, 10.73, 11.55, 12.43

Valve Sizing. Te chnic al Bulletin. Flow Calculation Principles. Scope. Sizing Valves. Safe Product Selection.

Chapter 10. Flow Rate. Flow Rate. Flow Measurements. The velocity of the flow is described at any

Chapter Applications of Energy Balance

Theory overview of flow measurement using differential pressure devices based on ISO-5167 standard.

VARIABLE DISPLACEMENT AXIAL PISTON PUMPS. For truck applications

( C) CLASS 10. TEMPERATURE AND ATOMS

= 800 kg/m 3 (note that old units cancel out) J 1000 g = 4184 J/kg o C

Extended-Horizon Analysis of Pressure Sensitivities for Leak Detection in Water Distribution Networks: Application to the Barcelona Network

Risk Management for Derivatives

ANNUBAR FLOW CALCULATION PROGRAM (For the FloBoss 103) User Manual (QER 04Q019)

RITTER Multiple Sonic Nozzle Calibration System

Salty Waters. Instructions for the activity 3. Results Worksheet 5. Class Results Sheet 7. Teacher Notes 8. Sample results. 12

The Precharge Calculator

ELECTRIC SERVO MOTOR EQUATIONS AND TIME CONSTANTS

Chapter 5. Principles of Unsteady - State Heat Transfer

Flow Measurement in Pipes and Ducts. Flow Measurement in Pipes and Ducts, Course #503. Presented by:

CE 3500 Fluid Mechanics / Fall 2014 / City College of New York

SIZING AND CAPACITIES OF GAS PIPING

General tolerances for Iinearand angular dimensions and geometrical=.tolerances

5.7 Chebyshev Multi-section Matching Transformer

8. Spring design. Introduction. Helical Compression springs. Fig 8.1 Common Types of Springs. Fig 8.1 Common Types of Springs

Measurement and Instrumentation. Analog Electrical Devices and Measurements

L4. Pipes Materials and Loads

Manure Spreader Calibration

CE 204 FLUID MECHANICS

Experiment 2 Index of refraction of an unknown liquid --- Abbe Refractometer

Physics 211: Lab Oscillations. Simple Harmonic Motion.

EUROMAP Extrusion Blow Moulding Machines Determination of Machine Related Energy Efficiency Class. Version 1.0, January pages

LECTURE 28 to 29 ACCUMULATORS FREQUENTLY ASKED QUESTIONS

Lecture L9 - Linear Impulse and Momentum. Collisions

Comparison of Thermal Insulation Materials for Building Envelopes of Multi-storey Buildings in Saint-Petersburg

SIZING AND CAPACITIES OF GAS PIPING (Not Adopted by the State of Oregon)

MEASUREMENT. Historical records indicate that the first units of length were based on people s hands, feet and arms. The measurements were:

For Water to Move a driving force is needed

Understanding Pressure and Pressure Measurement

CERTIFIED. Ellipse. The. Flow Sensor. Your First Choice in Intelligent Flow Management...

WEEK 1. Engineering Calculations Processes Process Variables

Unit 1 INTRODUCTION 1.1.Introduction 1.2.Objectives

11 CHAPTER 11: FOOTINGS

15.2. First-Order Linear Differential Equations. First-Order Linear Differential Equations Bernoulli Equations Applications

Custody Transfer Measurement. with the V-Cone Flowmeter

Crashworthiness Considerations for Van Structures

A Primer on Dimensions and Units

FLUID FLOW Introduction General Description

Drying and Dehydration

The Unique Accelabar Flow Meter

The ratio of inertial to viscous forces is commonly used to scale fluid flow, and is called the Reynolds number, given as:

Lesson 44: Acceleration, Velocity, and Period in SHM

Flow Measurement. Reference - Flow Measurement FUNDAMENTALS. ρ = fluid density (lb/ft3 or kg/m3)

Sizing Pressure Regulators & Control Valves

Chapter 10 Temperature and Heat

Heat Exchangers - Introduction

SCIENTIFIC CALCULATOR OPERATION GUIDE. <V/R Series>

LAB #3: MEASURING SPECIFIC GRAVITY AND DENSITY. Set-up and Materials for Experiment

Oildyne. 165 Series Hydraulic Power Units. Pressures to 241 bar (3500 psi) Flows to 5.4 lpm (1.4 gpm)

NOTE: FOR PROJECTS REQUIRING CONTRACTOR MIX DESIGN, THE DESIGN PROCEDURES ARE SPECIFIED IN THE SPECIAL PROVISIONS OF THE CONTRACT.

p atmospheric Statics : Pressure Hydrostatic Pressure: linear change in pressure with depth Measure depth, h, from free surface Pressure Head p gh

The Standard & Modified Proctor Density Tests

STRESS AND DEFORMATION ANALYSIS OF LINEAR ELASTIC BARS IN TENSION

Modeling and Simulations of Cavitating and Bubbly Flows

Strip Warpage Analysis of a Flip Chip Package Considering the Mold Compound Processing Parameters

Series GM. Magnetic Drive Gear Pump. Product Data Sheet

DESIGN OF VACUUM SECTION OF A LEAF COLLECTOR MACHINE

Chapter 14 Oscillations

1 Analysis of heat transfer in a single-phase transformer

Series TMM Axial Piston Motor. Technical Information

Transcription:

Basic low equation: Flow alculations or the V-one an Waer-one Floweters π g c ΔPps ρ 1 Volue lowrate π lb g c ρ ΔPps s 1 Δ Pps ΔPwc 5. 197 1 Mass lowrate 60 600 ac ach 7.805 7. 805 gp ac gph ach π Δ PPa Volue lowrate ρ 1 s π ρ Δ PPa Mass lowrate 1 kg s ΔPPa ΔPbar 100 1000 60 600 s L 1000 Page 1 h s L h h 1000 www.ccroeter.co 55 WEST STETSON AVENUE HEMET, ALIFORNIA 955 USA TEL: 951-65-6811 800-0-79 FAX: 951-65-078 Prte In The U.S.A Lit. #509-5 Rev../0-08 opyright 1995-008 Mcroeter, Inc. All prte aterial shoul not be change or altere without perission o Mcroeter. Any publishe pricg, technical ata, an structions are subject to change without notice. ontact your Mcroeter representative or current pricg, technical ata, an structions.

Gas Expansion Factor Precision tube V-one an Insertion Top-plate V-one Floweters (Rev. May 001) The equation or gas expansion or copressible lui low: NOTE: 1 or noncopressible luis (e.g. water, oil etc.). ΔP 1 (0.69 + 0.696 ) k P Note that Δ P an P can be any units as long as they are the sae. Waer-one Floweters (Rev. Oct 001) The equation or gas expansion or copressible lui low: NOTE: 1 or non-copressible luis (e.g. water, oil etc.). 8 ΔP 1 ( 0.755 + 6.787 ) k P The equation to convert ro actual to stanar / noral volue units: NOTE: This conversion is only use copressible luis. scs P P L b Tb T Zb Z N s s P P L b T T b Zb Z The basic equation ters o : NOTE: is use to sipliy the low equation by cobg the constant an geoetric variables. Page www.ccroeter.co 55 WEST STETSON AVENUE HEMET, ALIFORNIA 955 USA TEL: 951-65-6811 800-0-79 FAX: 951-65-078 Prte In The U.S.A Lit. #509-5 Rev../0-08 opyright 1995-008 Mcroeter, Inc. All prte aterial shoul not be change or altere without perission o Mcroeter. Any publishe pricg, technical ata, an structions are subject to change without notice. ontact your Mcroeter representative or current pricg, technical ata, an structions.

ΔPps ρ 6.00 1 ΔPPa ρ s 1.1107 1 Note that calibrate eters have expresse as a unction o Reynols Nuber. Thereore or the case o calibrate eters or will be expresse as unctions o Reynols Nuber. Lear velocity equations: v v throat π π v s s v throat π π Beta ratio an cone iaeter equations: 1 1 1 1 Page www.ccroeter.co 55 WEST STETSON AVENUE HEMET, ALIFORNIA 955 USA TEL: 951-65-6811 800-0-79 FAX: 951-65-078 Prte In The U.S.A Lit. #509-5 Rev../0-08 opyright 1995-008 Mcroeter, Inc. All prte aterial shoul not be change or altere without perission o Mcroeter. Any publishe pricg, technical ata, an structions are subject to change without notice. ontact your Mcroeter representative or current pricg, technical ata, an structions.

Beta Ratios: The stanar beta ratios or V-one loweters are: 0.5, 0.55, 0.65, 0.75, an 0.8. Alternative beta ratios can be use i require. Note that ierential pressure an/or gas expansion actor ay liit the availability o even stanar beta ratios. In a liqui application, beta ratios shoul not be use that cause static le pressure us the ierential pressure to be less than the lui s vapor pressure. In vapor or gas applications, beta ratios shoul not be use that generate a gas expansion actor less than 0.8. Reynols nuber equation: Re v ρ 1.9 μ Re μ v ρ The V-one eters ischarge coeicient is relate to the lows Reynols nuber. It is avise that the V-one eter be calibrate across the range o Reynols nubers or which it is to be use. That is a plot o ischarge coeicient to the Reynols nuber shoul be prouce an a le it relatg ischarge coeicient to the Reynols nuber shoul then be ae. Flowg ensity equations: Liquis: Stea: Gas: ρ Gr ρ ρ ρ 1 Sp.Vol. water Sg PL.6988 Z T Metric units: ρ ρ 16. 018 Theral expansion equation: When eters are subjecte to substantially ierent teperatures than those at which they were calibrate, there can be an eect on eter perorance ue to the expansion o the cone an eter tube aterials. Use this equation i the theral expansion coeicients or the pipe an cone are equal: 1+ α T 58 F a Page ( ) www.ccroeter.co 55 WEST STETSON AVENUE HEMET, ALIFORNIA 955 USA TEL: 951-65-6811 800-0-79 FAX: 951-65-078 Prte In The U.S.A Lit. #509-5 Rev../0-08 opyright 1995-008 Mcroeter, Inc. All prte aterial shoul not be change or altere without perission o Mcroeter. Any publishe pricg, technical ata, an structions are subject to change without notice. ontact your Mcroeter representative or current pricg, technical ata, an structions.

Use this set o equation i the coeicients are ierent: Fa ((1 α pipe (T 58)) ) ((1 α cone (T 58)) ) To calculate the theral expansion actor at operatg teperature base on beta ratio: ( ) alculate pipe iaeter at operatg teperature: + α ( T T ) alculate cone iaeter at operatg teperature: + ( α ( T T )) alculate beta ratio at operatg teperature: 1 pipe cone c c alculate theral expansion actor at operatg teperature: F a 1 1 The exaple below eonstrates the use o this ter: F (at _ new _ tep) a Peranent pressure loss equation: Peranent pressure (or total hea ) loss ierential pressure eters is typically escribe as a percentage o the ierential pressure create at a particular lowrate. An approxiate V-one Meter peranent pressure loss can be oun by applyg the ollowg equation: ( 1. 1.5 ) 100 % P loss Page 5 www.ccroeter.co 55 WEST STETSON AVENUE HEMET, ALIFORNIA 955 USA TEL: 951-65-6811 800-0-79 FAX: 951-65-078 Prte In The U.S.A Lit. #509-5 Rev../0-08 opyright 1995-008 Mcroeter, Inc. All prte aterial shoul not be change or altere without perission o Mcroeter. Any publishe pricg, technical ata, an structions are subject to change without notice. ontact your Mcroeter representative or current pricg, technical ata, an structions.

Noenclature eter constant etric eter constant ischarge coeicient o the eter eter sie iaeter eet eter sie iaeter ches ' pipe iaeter at operatg teperature ches eter sie iaeter eters eter sie iaeter illieters cone iaeter ches ' cone iaeter at operatg teperature ches cone iaeter illieters F a eter theral expansion actor g c iensional conversion constant,.17 lb / lb sec k lui isentropic exponent at lowg conitions P absolute pressure sae units as ΔP P b base absolute pressure psi (typically 1.696 psia) P b base absolute pressure bars (typically 1.01 bara) P L absolute static le pressure psi at the eter P L absolute static le pressure bars or psi at the eter volue low rate actual cubic eet per secon ac volue low rate cubic eet per ute ach volue low rate cubic eet per hour gp volue low rate gallons per ute gph volue low rate gallons per hour kg/s ass low rate kilogras per secon L/ volue low rate liters per ute L/h volue low rate liters per hour lb/s ass low rate pouns ass per secon / volue low rate cubic eters per ute /h volue low rate cubic eters per hour /s volue low rate actual cubic eters per secon N /h volue low rate noral cubic eters per hour sch volue low rate stanar cubic eet per hour sc volue low rate stanar cubic eet per R sipliication ter use actor Re Reynols nuber S g speciic gravity o the gas Sp.Vol. speciic volue o the vapor Page 6 www.ccroeter.co 55 WEST STETSON AVENUE HEMET, ALIFORNIA 955 USA TEL: 951-65-6811 800-0-79 FAX: 951-65-078 Prte In The U.S.A Lit. #509-5 Rev../0-08 opyright 1995-008 Mcroeter, Inc. All prte aterial shoul not be change or altere without perission o Mcroeter. Any publishe pricg, technical ata, an structions are subject to change without notice. ontact your Mcroeter representative or current pricg, technical ata, an structions.

T lowg teperature egrees Ranke T lowg teperature egrees Kelv T b base teperature egrees Ranke (typically 50 R) T b base teperature egrees Kelv (typically 88.15 K) T c calibration teperature T' operatg teperature v lui velocity through the pipe, eet per secon v lui velocity through the pipe, eters per secon v throat lui velocity at the throat, eet per secon v throat lui velocity at the throat, eters per secon aiabatic expansion actor or contoure eleents note: 1 or liqui low applications Z lowg gas copressibility actor base gas copressibility actor Z b %P loss peranent pressure loss across the eter as a percentage o ierential pressure Greek sybols: α PE α cone α pipe ' ΔP ΔP Pa ΔP bar ΔP wc pipe an cone aterial coeicient o theral expansion theral expansion coeicient o cone aterial theral expansion coeicient o pipe aterial eter beta ratio beta ratio at operatg teperature ierential pressure sae units as P ierential pressure Pascals ierential pressure illibars ierential pressure ches o water colun μ operatg lui viscosity, centipoise π.1159 ρ lowg lui ensity pouns ass per cubic oot ρ lowg lui ensity kilogras per cubic eter Page 7 www.ccroeter.co 55 WEST STETSON AVENUE HEMET, ALIFORNIA 955 USA TEL: 951-65-6811 800-0-79 FAX: 951-65-078 Prte In The U.S.A Lit. #509-5 Rev../0-08 opyright 1995-008 Mcroeter, Inc. All prte aterial shoul not be change or altere without perission o Mcroeter. Any publishe pricg, technical ata, an structions are subject to change without notice. ontact your Mcroeter representative or current pricg, technical ata, an structions.

OTHER McROMETER PROUTS INLUE: Magnetic Floweters Magnetic Floweters Magnetic Floweters Propeller Floweters Floweters An Flow Straighteners For Propeller Floweters Propeller Floweters ierential Pressure Floweters ierential Pressure Floweters ierential Pressure Floweters Electronic Instruentation or Reote isplay an ontrol U.S. Patents 6867, 8109, 56699, 9190 an 5,81,78; anaian Patent 1511; European Patent 07711; Japan patent 1,858,116 Waer-one: Hong Kong Patents HK1076 & HK106605; Other U.S. an Foreign patents peng 08 www.ccroeter.co 55 WEST STETSON AVENUE HEMET, ALIFORNIA 955 USA TEL: 951-65-6811 800-0-79 FAX: 951-65-078 Prte In The U.S.A Lit.#509-5 Rev../0- opyright 005-008 Mcroeter, Inc. All prte aterial shoul not be change or altere without perission o Mcroeter. Any publishe pricg, technical ata, an structions are subject to change without notice. ontact your Mcroeter representative or current pricg, technical ata, an structions.