INSTALLATION INSTRUCTIONS Accessory Application Publications No. XM RADIO SYSTEM 2003 ACCORD 4 DOOR AII 24378 Issue Date MARCH 2003 The XM Radio will not fit in a vehicle equipped with a rear entertainment system. Template PARTS LIST XM Radio Attachment Kit (sold separately): P/N 08B15-SDA-100 Double-sided adhesive tape DIN cable Display module pocket XM radio harness Clip nut Front unit bracket 3 Self-tapping screws Fastener Rear unit bracket Ground bolt (gold) 6 Washer-screws, 4 x 8 mm Bracket A 6 Washer-bolts, 6 x 12 mm Bracket B Bracket C 4 Flange nuts, 4 mm 29 Wire ties 2003 American Honda Motor Co., Inc - All Rights Reserved. AII 24378 (0303) 08B15-SDA-1001-91 1 of 24
Connector clip Base Kit (sold separately): P/N 08A15-1E1-000 Display Module 8 Wire tie with clips (two not used) 5 Cushion tapes FM modulator unit 5 EPT seals Receiver unit Fuse label Owner's Manual Mini fuse, 5A Antenna Kit (sold separately): P/N 08A15-1E1-100 Antenna cable 2 of 24 AII 24378 (0303) 2003 American Honda Motor Co., Inc - All Rights Reserved.
Audio Attachment Kit (sold separately): P/N 08B06-SDA-100 (Not required if already equipped with a player.) BUS cable (Navigation equipped vehicle's only) Left player bracket 2 Latches Right player bracket 8 Flange nuts, 6 mm 2 Grommet screws 2 Wire ties Left player subbracket Right player subbracket 3 EPT seals Player base-bracket 2 Self-tapping screws, 4 x 12 mm Player panel Audio Subharness (sold separately): P/N 08A31-0E1-010 If the vehicle is equipped with a navigation system and already has an installed cassette/mp3/cd player, use this audio subharness cable. Do not use this cable when the vehicle is only to be equipped with the XM radio. Audio subharness cable Pocket 2003 American Honda Motor Co., Inc - All Rights Reserved. AII 24378 (0303) 3 of 24
TOOL AND SUPPLIES REQUIRED Phillips screwdriver Stubby phillips screwdriver Flat-tip screwdriver Isopropyl alcohol Shop towel Tape measure Utility knife Hook tool Ratchet wrench 8 mm and 10 mm Sockets Felt-tip pen Scissors Push pin Vinyl tape Drill 3 mm and 10 mm Drill bits Touch-up paint Eye protection (face shield, safety goggles, etc.) Masking tape Illustration of an Installed XM Radio System DISPLAY MODULE DIN FM MODULATOR UNIT DISPLAY MODULE XM RADIO ANTENNA RECEIVER UNIT ANTENNA FM MODULATOR UNIT 2N28160M DIN FUSE BOX 6-PIN XM RADIO RECEIVER UNIT ANTENNA 2N28010M INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your car. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons. 2. Disconnect the negative cable from the battery. 4 of 24 AII 24378 (0303) 2003 American Honda Motor Co., Inc - All Rights Reserved.
3. Remove the trim ring. M/T Vehicle: Squeeze the plastic clip, and pull down on the shift boot. Remove the shift knob by turning it counterclockwise. A/T Vehicle: Gently pry on the trim ring to release the six clips. Unplug the two seat heater connectors (if equipped), and remove the trim ring. SHIFT KNOB (Turn counterclockwise.) RETAINING CLIPS (4) RETAINING CLIPS (2) PLASTIC CLIP TRIM RING SHIFT BOOT 2206032K SEAT HEATER (If equipped.) Gently pry up on the trim ring to release the six clips. Unplug the two seat heater connectors (if equipped), and remove the trim ring. RETAINING CLIPS (4) RETAINING CLIPS (2) 4. Remove the center holder. Open the lid, and remove the coin pocket. Remove the two self-tapping screws. 2206112K Gently pull out the dashboard center holder to release the two retaining clips, unplug the vehicle connector, and remove the center holder. With Coin Pocket: COIN LID CENTER HOLDER TRIM RING SELF-TAPPING SEAT HEATER (If equipped.) 2206041K RETAINING CLIPS (2) 2206061K 2003 American Honda Motor Co., Inc - All Rights Reserved. AII 24378 (0303) 5 of 24
With Optional Ashtray: Open the lid, and remove the ashtray. Remove the two self-tapping screws. Gently pull out on the two retaining clips, unplug the cigarette lighter harness connector, vehicle connector, illumination bulb, and remove the center holder. ASHTRAY SELF-TAPPING CENTER HOLDER ILLUMINATION BULB If the vehicle is equipped with a cassette/mp3/cd player, go to step 13; otherwise, go to step 5. 5. Remove the pocket: Apply masking tape to the edge of the center panel. Remove the two self-tapping screws. Push in on the bottom of the lid, then pull out on the top by inserting the end of a hook tool between the pocket and center panel. Pull the pocket toward you to release the two retaining clips. Set the pocket aside; it will not be reused. HOOK TOOL MASKING TAPE RETAINING CLIPS (2) RETAINING CLIPS (2) LID 2730010K CIGARETTE LIGHTER SELF-TAPPING 2206073K 6. Remove the right and left inner covers (one hook and one clip for each cover). Set the inner covers aside; they will not be reused. CLIP LEFT INNER COVER RIGHT INNER COVER HOOK OPENING 2226010K 6 of 24 AII 24378 (0303) 2003 American Honda Motor Co., Inc - All Rights Reserved.
7. Remove the vehicle harness clip from the vehicle frame, and move the clip out of the way. BASE- FRAME CLIP (Remove.) 10. Get the pocket from the audio attachment kit. Using a utility knife, cut the two lugs off of the pocket. LUG (Cut.) 6 mm FLANGE NUT LUG 2529041T CLIP (Insert into the hole of the player base bracket.) FRAME 6 mm FLANGE 2306011T NUT 8. Insert the studs from the player base-bracket into the holes in the vehicle frame from the back. Install the two 6 mm flange nuts while holding the bracket firmly against the vehicle frame. Insert the vehicle harness clip (removed in step 7) into the hole in the player base-bracket. 11. Install one latch onto the left and right player brackets. Slide the clip nut onto the display module pocket flange. LATCH 1 mm LATCH DISPLAY MODULE FLANGE CLIP NUT 9. Insert the studs of the left and right player subbrackets into the holes in the vehicle frame, and install one 6 mm flange nut on the end of each stud while pushing each subbracket upward. 6 mm FLANGE NUT SELF-TAPPING (2) (Supplied with audio attachment kit) DISPLAY MODULE FRAME FRAME LEFT POSITION SELF-TAPPING S (3) (Supplied with XM radio RIGHT attachment kit) 2N28071M HOLE LEFT SUB RIGHT SUB 2306021T 12 Set the display module pocket on the pocket with the cut out facing up. Position the left and right player brackets on the display module pocket and pocket, and install five self-tapping screws. 2003 American Honda Motor Co., Inc - All Rights Reserved. AII 24378 (0303) 7 of 24
If the vehicle is not equipped with a cassette/mp3/ CD player, go to step 18; otherwise, go to step 13. 13. Remove the player panel by removing the two self-tapping screws and two clips. 15. Remove the left and right audio brackets (two washer-screws and one self-tapping screw for each bracket). Separate the player and pocket. Set the pocket aside; it will not be reused. PANEL CLIP WASHER- LEFT (Cassette/MP3/CD) RIGHT WASHER- SELF-TAPPING 2306141T 14. Remove the player/pocket assembly. Unscrew the four flange nuts, and pull the assembly out toward you. Unplug the audio subharness cable connector. (without navigation (with navigation system) system) SUB (with navigation system) LEFT SUB (without navigation system) LEFT SUB SELF- TAPPING SELF-TAPPING 2N28080M (Do not reuse.) 16. Slide the clip nut (supplied) onto the display module flange. WASHER- (Supplied with Audio Attachment kit) DISPLAY MODULE (Cassette/MP3/CD) CLIP NUT WASHER- (Supplied with Audio Attachment kit) SELF- TAPPING 6 mm FLANGE NUT RIGHT BASE- 2306120T RIGHT SUB HOLE POSITION LEFT DISPLAY MODULE RIGHT SELF-TAPPING S (2) (Supplied with XM radio attachment kit) 17. Set the player on the display module pocket. Position the left and right player brackets on the display module pocket and player, and reinstall the four washer-screws. Install the the three selftapping screws to secure the display module pocket. 8 of 24 AII 24378 (0303) 2003 American Honda Motor Co., Inc - All Rights Reserved.
Installing the Display Module 18. Attach the display module to the display module pocket: Using isopropyl alcohol on a shop towel, clean the center on the back of the display module where the adhesive backing will attach. Remove the backing from one side of the double-sided adhesive tape, and attach it to the display module. Remove the remaining backing from the double-sided adhesive tape. Route the display module cable through the hole of the display module pocket, and attach the display module to the pocket. Routing the XM Radio Harness 19. Remove the beverage holder (pull up to release the six retaining clip). RETAINING CLIPS (4) RETAINING CLIPS (2) BEVERAGE HOLDER DISPLAY MODULE DOUBLE-SIDED ADHESIVE TAPE BACKING Without Player Clean with isopropyl alcohol. DISPLAY MODULE 20. Remove the rear console. 2206050K Open the lid, and remove the rear console mat from inside the rear console. Remove the two screws and four self-tapping screws, and unplug the connector and harness clip (if equipped). If equipped with a console-mounted CD changer, remove the changer from the rear console. DISPLAY MODULE With Player REAR CONSOLE MAT S (2) SELF-TAPPING S (4) DISPLAY MODULE DISPLAY MODULE 2N28110M CLIP (If equipped.) (If equipped.) 2206090K 2003 American Honda Motor Co., Inc - All Rights Reserved. AII 24378 (0303) 9 of 24
21. Remove the driver s dashboard lower cover: Remove the one self-tapping screw. Release the four clips on the left side first by pulling out on the driver's dashboard lower cover. After releasing the four clips, insert a flat-tip screwdriver behind the clip at the dashboard frame. Gently twist the screwdriver to release the clip. Release the two clips on the right side. Unplug the vehicle connector, then remove the lower cover. 23. Remove the self-tapping screw and the clip that secure the left front console cover. Take care not to damage the clip, and remove the console cover. SELF-TAPPING CLIP DASHBOARD LOWER COVER LEFT FRONT CONSOLE COVER PUSH REMOVE 2206131K 24. Remove the glove box by removing the two bolts, and then release the damper rod. SELF- TAPPING RETAINING CLIPS (7) 2206120K PUSH DAMPER ROD 22. If equipped, remove the driver s dashboard under cover (release the three retaining clips, one pin, and one holder). GLOVE BOX BOLTS (2) HOLDER 2524010M PIN RETAINING CLIPS (3) DRIVER S DASHBOARD UNDER COVER 2205020T 10 of 24 AII 24378 (0303) 2003 American Honda Motor Co., Inc - All Rights Reserved.
25. On the driver's side of the vehicle, locate the 6-pin conector on the fuse box. Plug the XM radio harness 6-pin connector into the fuse box 6-pin connector. 27. Install the XM radio harness fuse cases and the 6-pin dummy connector to the fuse box case. NOTE: If the 6-pin connector is already being used by another accessory, locate the 6-pin connector taped to the XM radio harness. Remove the dummy connector from the harness, and plug the other accessory's harness 6-pin connector into the XM radio harness. OTHER ACCESSORY 6-PIN Fuse case position (Do not secure to the yellow SRS harness.) FUSE CASES WIRE TIE XM RADIO XM RADIO 6-PIN DUMMY (Discard.) 2524060M 6-PIN FUSE BOX 6-PIN FUSE CASES XM RADIO 6-PIN WITH DUMMY 28. Secure the XM radio harness to the vehicle harness with one wire tie. Do not secure it to the yellow SRS harness. 29. Route the XM radio harness under the steering shaft and toward the center console. 2N28020M FUSE LABEL 2A LABEL 5A LABEL XM RADIO CLIP 2524051M FUSE LABEL WIRE TIES (3) CENTER CONSOLE 3121030M Use these labels. XM RADIO 26. Attach the fuse labels to the fuse cases on the XM radio harness. 30. Loosely attach the XM radio harness to the vehicle harness with three wire ties. 2N28030M 2003 American Honda Motor Co., Inc - All Rights Reserved. AII 24378 (0303) 11 of 24
31. Inside the center console, locate the welded nut on the vehicle stay. Attach the XM radio harness ground terminal to the welded nut with the ground bolt supplied. GROUND BOLT (Supplied) WELDED NUT If the vehicle is not equipped with a cassette/mp3/ CD player, go to step 34; otherwise, go to step 33. 33. Plug the audio subharness cable into the player. Without Navigation System: Cassette Player Make loops in the audio subharness cable, and secure it with one wire tie, so that the distance between the ends of the cable connector is 200 mm. Plug the audio subharness cable connector into the cassette player connector. CASSETTE 3-PIN WIRE TIE (Supplied with audio attachment kit) 2N28040M GROUND TERMINAL XM RADIO CENTER CONSOLE 32. Route the XM radio harness 3-pin connector toward the glove box opening. Set the remaining XM radio harness aside; it will be routed later. SUB SUB 200 mm SUB 2306051T Multimedia Player Make loops in the audio subharness cable, and secure it with one wire tie so that the distance between the ends of the cable connectors is 200 mm. Plug the audio subharness cable connector into the multimedia player connector. MULTIMEDIA BUS SUB WIRE TIE (Supplied with audio attachment kit) SUB 200 mm 2306061T 12 of 24 AII 24378 (0303) 2003 American Honda Motor Co., Inc - All Rights Reserved.
In-Dash CD Player Make loops in the audio subharness cable, and secure it with one wire tie so that the distance between the ends of the cable connector is 180 mm. Plug the audio subharness cable connector into the connector from the in-dash CD player. After connecting, secure the connectors to the rear of the in-dash player with one wire tie from in the in-dash CD player kit. IN-DASH CD WIRE TIE (Supplied with audio attachment kit) Cassette Player CASSETTE Multimedia Player SUB SUB 2306090T SUB 180 mm WIRE TIE (Supplied with audio attachment kit) SUB MULTIMEDIA With Navigation System: SUB 2306070T Remove the tape that secures the vehicle harness to the upper left pocket opening, and pull the harness out through the pocket opening. SUB In-Dash CD Player 2306100T After connecting, secure the connectors to the rear of the in-dash CD player with one wire tie from the in-dash CD player kit. IN-DASH CD SUB TAPE (Remove.) OPENING 2306080T IN-DASH CD CHANGER WIRE TIE (Supplied with audio attachment kit.) SUB SUB 2306110T 2003 American Honda Motor Co., Inc - All Rights Reserved. AII 24378 (0303) 13 of 24
34. To protect the center panel, attach strips of masking tape to the center panel in the area shown. CENTER PANEL MASKING TAPE 37. Inside the glove box opening, locate the frame stay pipe. Align the holes in the frame stay pipe with the welded nuts in bracket A, and loosely attach bracket A to the pipe frame with two 6 x 12 mm washer-bolts. FRAME STAY PIPE A 6 x 12 mm WASHER-BOLT 2506010T 35. Get a DIN cable from the XM radio attachment kit. Route the 90 end of the DIN cable through the dashboard opening and toward the FM modulator unit. 6 x 12 mm WASHER BOLT 2524100M XM RADIO DIN (90 end) 38. Attach the connector clip to the harness connector of the FM modulator unit. Attach bracket B to the FM modulator unit with one 4 x 8 mm washerscrew. Tighten the washer-screw securely. TO THE FM MODULATOR UNIT B 4 x 8 mm WASHER- (with pocket) DISPLAY MODULE DISPLAY MODULE ASSEMBLY (with player) 2N28120M 36. Place the display module assembly near the dashboard opening, and route the display module cable toward the FM modulator unit alongside the XM radio harness (3-pin connector) and the DIN cable. FM MODULATOR UNIT CLIP 2524121M 14 of 24 AII 24378 (0303) 2003 American Honda Motor Co., Inc - All Rights Reserved.
39. Plug the DIN cable and the display module cable into the FM modulator unit. 42. Below the glove box opening, remove the upper heater blower case mounting bolt. A B 6 x 12 mm WASHER-BOLT DISPLAY MODULE FM MODULATOR UNIT DIN 40. Attach bracket B with the FM modulator unit against bracket A, and install one additional 6 x 12 mm washer-bolt. Tighten all three 6 x 12 mm washer-bolts securely. 41. Route the antenna harnesses from the FM modulator unit rearward along the DIN cable toward the inside of the front console. BOLT (Reuse.) 43. Attach bracket C to the bottom of the FM modulator unit with one 4 x 8 mm washer-screw, and attach the other end of bracket C to the upper heater blower using the bolt you removed in step 42. FM MODULATOR UNIT 3-PIN HEATER BLOWER CASE 2524111M FM MODULATOR UNIT ANTENNA ES WIRE TIE WITH CLIP FM MODULATOR UNIT FM MODULATOR UNIT ANTENNA FM MODULATOR C BOLT (Reuse.) 4 x 8 mm WASHER FM MODULATOR UNIT ANTENNA ES FM MODULATOR UNIT 3-PIN 44. On the back of the FM modulator unit, attach one wire tie with clip to the antenna harnesses, and attach the wire tie with clip to the hole in bracket C. 2003 American Honda Motor Co., Inc - All Rights Reserved. AII 24378 (0303) 15 of 24
45. Connect the XM radio harness 3-pin connector to the FM modulator unit harness 3-pin connector, then attach the 3-pin connector clip to the hole in bracket B. B 48. Secure the XM radio harness to the vehicle harness with one wire tie. WIRE TIE XM RADIO XM RADIO 3-PIN (with pocket) FM MODULATOR UNIT 3-PIN DISPLAY MODULE ASSEMBLY 46. Unplug the vehicle antenna cable, and plug it into the FM modulator unit antenna cable. Plug the other FM module antenna jack into the vehicle antenna cable. WIRE TIE (with player) 2N28140M WIRE TIE 49. Bundle up the excess display module cable, and secure it with one wire tie. EPT SEAL FM MODULATOR ANTENNA 2N28130M ANTENNA DISPLAY MODULE (Bundle up.) WIRE TIE 47. Wrap one EPT seal around the antenna jack, and secure the antenna jack to the vehicle antenna jack with one wire tie. Secure the DIN cable, the display module cable, and the antenna harness to the vehicle harness with one wire tie. 16 of 24 AII 24378 (0303) 2003 American Honda Motor Co., Inc - All Rights Reserved.
50. Plug the BUS cable connector into the vehicle connector. If the vehicle is equipped with a navigation system, wrap the connectors with one EPT seal. 53. Get one EPT seal. Measure the EPT seal, and use scissors to cut it into three pieces. EPT SEAL (Cut off the marked area.) PANEL BUS (with navigation system) LEFT (with navigation system) (without navigation system) EPT SEAL BUS (without navigation system) LEFT SUB 8 mm (with player) 6 mm FLANGE NUTS (4) (with pocket) DISPLAY MODULE ASSEMBLY STUD 2N28150M RIGHT 51. Install the display module assembly onto the studs of the left and right player subbrackets, and install the 6 mm flange nuts. Tighten the flange nuts securely. 52. If the vehicle is not equipped with a player, attach the two grommet screws to the player panel in the square holes as shown. PANEL EPT SEAL CLIP LATCH 8 mm 2612010T 54. Using isopropyl alcohol on a shop towel, clean the player panel in the area shown. Attach the two cut pieces of the EPT seal to the player panel, and cut off the excess. 55. Attach the player panel by inserting the clips into the latches, and install two self-tapping screws from the kit or reinstall the two self-tapping screws you removed in step 13. Remove the masking tape. PANEL SELF- TAPPING S (Reuse.) 2306141T GROMMET S 2306131T 2003 American Honda Motor Co., Inc - All Rights Reserved. AII 24378 (0303) 17 of 24
56. Inside the passenger compartment, remove the rear seat cushion by removing the bolt and releasing the two locks (pull the hook out toward you). BOLT 58. Inside the trunk, fold the rear seat-back forward by pulling the lever under the rear shelf. REAR SEAT BACK LEVER (Pull.) REAR SEAT CUSHION Pull down. Pull. HOOK (Pull.) 2527040M LOCK (2) 59. Remove the spare tire cover (one clip). 2226040K 57. Remove the right side cushion by removing one bolt and one hook. CLIP CUSHION HOOK SPARE TIRE COVER 2322010T BOLT 2527030M 18 of 24 AII 24378 (0303) 2003 American Honda Motor Co., Inc - All Rights Reserved.
60. Remove the rear trim panel (four clips). REAR TRIM PANEL 62. Remove the right trunk side liner: If equipped, remove the hook (one bolt, hook, and washer). Remove the four clips. Gently pull out on the trunk liner, and remove it. WASHER BOLT HOOK (If equipped.) TRUNK WEATHERSTRIP CLIPS (4) 2325010T Remove 61. Remove the maintenance lid. Remove the jack cover and the jack. CLIPS (4) 2527050M MAINTENANCE LID JACK COVER 63. Inside the trunk area, unplug the high mount brake light harness connector. Inside the cabin, remove the high mount brake light from the rear shelf by releasing the four hooks and pulling out on the brake light assembly. Take care not to damage the clips. HIGHT MOUNT BRAKE LIGHT ASSEMBLY HOOKS (4) JACK 2502010T REAR SHELF HIGH MOUNT BRAKE LIGHT 2527060M 2003 American Honda Motor Co., Inc - All Rights Reserved. AII 24378 (0303) 19 of 24
64. Route the XM radio harness and the DIN cable along the vehicle harness toward the parking brake lever, and under the floor carpet. Secure the harness and DIN cable to the vehicle harness with five wire ties in the areas shown. XM RADIO AND DIN 66. Remove the spacer from the rear quarter panel opening. WIRE TIES WITH CLIPS (2) (without navigation system) BLACK SEAL (Remove.) SPACER (Remove and reinstall.) WIRE TIES (with navigation system) WIRE TIES (5) 2527072M WIRE TIES (3) 65. Raise the rear seat back. Pull the XM radio harness and DIN cable out from under the floor carpet and toward the passenger's side of the vehicle. Secure the harness and DIN cable to the vehicle harness with two wire ties. Attach the harness and DIN cable to the floor panel with four cushion tapes in the areas shown. FLOOR PANEL Align CUSHION TAPES (4) CLIP REAR SEAT BACK 2527090M 67. Route the XM radio harness and DIN cable up along the vehicle harness into the trunk. Without Navigation System: Remove the two black seals from the body. Attach two wire ties with clips to the radio harness and DIN cable near the body holes. Insert the wire tie clips into the holes in the body, and secure the lower portion with three additional wire ties. Reinstall the spacer. With Navigation System: Secure the XM radio harness and DIN cable to the vehicle harness with five wire ties in the areas shown. Reinstall the spacer. WIRE TIES (2) 2527080M 20 of 24 AII 24378 (0303) 2003 American Honda Motor Co., Inc - All Rights Reserved.
Installing the Antenna 68. Get the antenna kit. Using isopropyl alcohol on a shop towel, clean the bottom of the antenna. Remove the adhesive backing from the fastener, and attach the fastener to the bottom of the antenna. 71. Route the antenna cable through the groove in the high mount brake light case, and reinstall the brake light case. HIGH MOUNT BRAKE LIGHT CASE GROOVE ANTENNA HIGH MOUNT BRAKE LIGHT OPENING ANTENNA (toward rear) ANTENNA Clean with isopropyl alcohol. FASTENER 2808031M REAR TRAY CUSHION TAPE ADHESIVE BACKING 2618012M REAR SPEAKER GRILL 72. Route the antenna cable along the vehicle harness, and secure it to the vehicle harness with seven wire ties in the areas shown. 69. Route the antenna cable through the high mount brake light opening, and install the antenna onto the rear tray in the area shown. Attach one cushion tape to the edge of the high mount brake light opening where the cable touches it. WIRE TIES (7) 70. Using a utility knife, cut the high mount brake light case to make a groove for the cable using the measurement shown. Remove any burrs from the edges. HIGH MOUNT BRAKE LIGHT CASE ANTENNA 2620010M 5 mm 10 mm 50 mm GROOVE 2806010M 2003 American Honda Motor Co., Inc - All Rights Reserved. AII 24378 (0303) 21 of 24
73. Secure the antenna cable, the DIN cable, and the XM radio harness with three wire ties with clips. Insert the clips on the wire ties into the panel holes. WIRE TIES WITH CLIPS (3) 75. Position the template on the right trunk side panel, and tape the template in place. While wearing eye protection, center punch the three cross marks on the template. CROSS MARKS (3) MASKING TAPE RIGHT TRUNK SIDE PANEL RADIO ANTENNA DIN 2620050M ANTENNA CENTER PUNCH TEMPLATE 2527110M 76. Remove the template. Place a shop towel on the inside of the right trunk side panel to collect any metal shavings. 74. Using scissors, cut out the shaded areas from the template. 8 mm DRILL BIT TEMPLATE SHOP TOWEL 10 mm 2527121M VINYL TAPE Cut (shaded areas) 77. Drill three 8 mm holes through the inner panel: Wrap vinyl tape around the drill bit 10 mm from the end, or attach a drill stop. 2527100M While wearing eye protection, drill an 8 mm hole through each center-punched mark. Remove all burrs and metal shavings, and apply touch-up paint to the edges of each drilled hole. Remove and discard the shop towel. 22 of 24 AII 24378 (0303) 2003 American Honda Motor Co., Inc - All Rights Reserved.
78. Install the front and rear unit brackets to the receiver unit using two 4 x 8 mm washer-screws and two 4 mm flange nuts for each bracket. 80. Attach the receiver unit to the body panel using three 6 x 12 mm washer-bolts. Tighten the bolts securely. FRONT UNIT 4 x 8 mm WASHER S (4) 6 x 12 mm WASHER-BOLTS (3) RECEIVER UNIT RECEIVER UNIT 4 mm FLANGE NUTS (4) REAR UNIT DRILLED HOLES (3) 2527131M 2621020M 79. Position the receiver unit between the right trunk side panel and the rear fender panel, and plug in the antenna cable connectors, the DIN cable connector, and the XM radio harness connector using the panel hole to access the receiver unit. 81. Attach two cushion tapes to the edges of the panel in the areas shown. PANEL HOLE CUSHION TAPES ANTENNA AND DIN DIN XM RADIO ANTENNA FENDER PANEL 2621031M CUSHION TAPES (2) WIRE TIE WITH CLIP PANEL HOLE RIGHT TRUNK SIDE PANEL RECEIVER UNIT 2621010M 82. Inside the fender area, bundle up the excess antenna cable and DIN cable, and secure them with one wire tie with clip to the hole in the rear unit bracket. 83. Wrap the ends of the antenna cable and the DIN cable with two cushion tapes. 2003 American Honda Motor Co., Inc - All Rights Reserved. AII 24378 (0303) 23 of 24
84. Install the 5A fuse provided into the No. 33 slot of the fuse box. FUSE BOX FUSE (5A) 86. Check that all wire harnesses and cables are routed properly and all connectors are plugged in. 87. Reinstall all removed parts. Check that all clips and fasteners are installed securely. 88. Reconnect the negative cable to the battery. 89. Enter the radio anti-theft code, and reset the customer's radio station presets. 90. Set the clock. 91. Set one of the radio station presets to FM 88.7 and check the operation of the XM radio. If necessary, use the XM radio Owner s Manual supplied. NOTE: Whenever the battery is disconnected, the driver s window AUTO up function is disabled. 92. Do the driver's window AUTO up procedure: FUSE BOX COVER 5A FUSE LABEL No. 33 2219080T 85. Attach the 5A fuse label over the No. 33 position on the fuse box cover. Start the engine. Push down on the driver s window switch until the window is fully open. Pull up on the driver s window switch to close the window completely, and hold the switch for 2 seconds. Test the window AUTO up function. 93. Do the ECM/PCM idle learn procedure: Make sure all electrical items are turned off. Start the engine. Hold the engine speed at 3,000 rpm with no load (in Park or Neutral) until the radiator fan comes on. Let the engine idle for about 5 minutes with the throttle fully closed and with all electrical items off. NOTE: If the radiator fan comes on during this step, the time when it is operating must not be included in the 5 minutes. 2219090T 24 of 24 AII 24378 (0303) 2003 American Honda Motor Co., Inc - All Rights Reserved.