60W PWM output LED power supply Ⅱ IP67 Ⅱ
TRC ELECTRONICS, 60W PWM output INC. LED power supply SPECIFICATION MODEL OUTPUT INPUT PROTECTION DC VOLTAGE RATED CURRENT RATED POWER DIMMING RANGE PWM FREQUENCY (Typ.) VOLTAGE TOLERANCE SETUP, RISE TIME Note.2 HOLD UP TIME (Typ.) VOLTAGE RANGE FREQUENCY RANGE 90 ~ 30VAC 47 ~ 63Hz 127 ~ 431VDC POWER FACTOR (Typ.) TOTAL HARMONIC DISTORTION PF>0.97/11VAC, PF>0.9/230VAC, PF>0.92/277VAC at full load (Please refer to "Power Factor Characteristic" curve) THD< 20% when output loading 60% at 11VAC/230VAC input and output loading 7% at 277VAC input EFFICIENCY (Typ.) 86% 89% 90% 90% AC CURRENT (Typ.) 0.8A / 11VAC 0.4A / 230VAC 0.32A / 277VAC INRUSH CURRENT(Typ.) COLD START 0A(twidth=270 μs measured at 0% Ipeak) at 230VAC LEAKAGE CURRENT SHORT CIRCUIT WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION OTHERS NOTE MAX. NO. of PSUs on 16A CIRCUIT BREAKER OVER LOAD OVER VOLTAGE OVER TEMPERATURE SAFETY STANDARDS SAFETY & WITHSTAND VOLTAGE EMC ISOLATION RESISTANCE EMC EMISSION EMC IMMUNITY PWM6012 PWM6024 PWM6036 PWM6048 12V 24V 36V 48V A 2.A 1.67A 1.2A 60W 60W 60.12W 60W 0 ~ 100% 300Hz ±4.0% ±3.0% ±2.0% ±1.0% 00ms, 80ms at 9% load 11VAC / 230VAC 16ms/230VAC 16ms/11VAC at full load 9 units (circuit breaker of type B) / 16 units (circuit breaker of type C) at 230VAC <0.2mA / 277VAC Hiccup mode, recovers automatically after fault condition is removed 108 ~ 120% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed 1 ~ 17V 28 ~ 34V 41 ~ 46V 4 ~ 60V Protection type : Shut down o/p voltage, repower on to recover Shut down o/p voltage, repower on to recover 40 ~ 70 (Refer to "Derating Curve") 20 ~ 9% RH noncondensing 40 ~ 80, 10 ~ 9% RH ± 0.03%/ (0 ~ 0 ) 10 ~ 00Hz, G 12min./1cycle, period for 72min. each along X, Y, Z axes UL870(type HL ), CSA C22.2 No. 20.1312, ENEC EN613471, EN61347213, EN62384 independent, IP67 approved; Design refer to EN60331 I/PO/P:3.7KVAC I/PO/P:100M Ohms / 00VDC / 2 / 70% RH Compliance to EN01, EN6100032 Class C ( 60% load) ; EN6100033 Compliance to EN6100042,3,4,,6,8,11; EN6147, light industry level(surge LN: 2KV), criteria A MTBF 271.03K hrs min. MILHDBK217F (2 ) DIMENSION 10*3*3mm (L*W*H) PACKING 0.49Kg;30pcs/1.7Kg/1.0CUFT
60W PWM output LED power supply Block Diagram PFC fosc : 0~120KHz PWM fosc : 60~130KHz I/P EMI FILTER & RECTIFIERS PFC CIRCUIT O.T.P. O.L.P. POWER SWITCHING PWM & PFC CONTROL RECTIFIERS V & DIMMING V FILTER CIRCUIT O.L.P. DIM DIM DETECTION CIRCUIT O.V.P. Derating Curve Static Characteristics 100 100 90 80 60 230VAC Input only 80 70 LOAD (%) 0 40 20 LOAD (%) 60 0 40 40 2 10 0 1 30 0 60 70 AMBIENT TEMPERATURE ( ) (HORIZONTAL) 90 100 12 13 14 1 16 17 180 200 230 30 INPUT VOLTAGE (V) 60Hz Power Factor Characteristic Constant Voltage Mode 1.0 0.9 0.8 PF 0.7 0.6 0. 0.4 0.3 277V 230V 11V 10% 20% 30% 40% 0% 60% 70% 80% 90% 100% (60W) LOAD
60W PWM output LED power supply EFFICIENCY vs LOAD (48V Model) possess superior working efficiency that up to 90% can be reached in field applications. 92% 90% EFFICIENCY (%) 88% 86% 84% 82% 277V 230V 11V 80% 78% 10% 20% 30% 40% 0% 60% 70% 80% 90% 100% LOAD DIMMING OPERATION The PWM style output is a simple switching of supply ON/OFF at a rate so fast that the human eye cannot see led flickering. Duty cycle describes the proportion of time when output voltage is on relative to the entire period of time. It is expressed in percentage, 100% being fully on (maximal brightness) and a low duty cycle corresponding to lower brightness. Builtin 3 in 1 dimming function. The duty of the PWM style output can be adjusted through output cable by connecting a 0~10Vdc or 10V PWM signal or resistance between DIM and DIM. Connection V LED Strips V DIM 0~10Vdc or 10V PWM or resistance control dimmer DIM DO NOT connect "DIM to V"
Providing exceptional customer 60W service PWM since output 1982 LED power supply Duty cycle of output current VS Dimming input 100% 90% 100% when DIM/DIM are open circuit. Duty cycle of output current 80% 70% Note : 1. Min. dimming level is about 6% 2. The output current is not defined when 0%< Iout<6% 60% 3. The output current could drop down to 0% when dimming input 0% is about 0KΩor 0Vdc, or 10V PWM signal with 0% duty cycle 40% 30% 20% 10% Note 0% 0V 1V 2V 3V 4V V 6V 7V 8V 9V 10V 0~10V 0% 10% 20% 30% 40% 0% 60% 70% 80% 90% 100% Short 10K/N 20K/N 30K/N 40K/N 0K/N 60K/N 70K/N 80K/N 90K/N 100K/N Duty cycle of 10V PWM (frequency range = 100~3KHz) Short~100K Ω/N resistance (N=driver quantity for synchronized Dimming input dimming operation ) PWM Style Output ON Output DC current Duty cycle(%) = TON 100% T OFF Output PWM frequency : 300Hz fixed (Typ.) TON T Mechanical Specification Case No.: NPF60A Unit:mm 10 300±20 AC/L(Brown) AC/N(Blue) SJTW 18AWG 2C ψ4. 3 3 T case 13 T case: Max. Case Temperature 300±20 UL2464 18AWG 2C(V,V) UL2464 22AWG 2C(DIM,DIM) V(Red) V(Black) DIM(Blue) DIM(White) 3 Recommend Mounting Direction
TRC ELECTRONICS, 60W PWM output INC. LED power supply Installation Manual Connection AC/L(BROWN) AC/N(BLUE) V(RED) V(BLACK) LED Strip DIM(BLUE) DIM(WHITE) 0~10Vdc or 10V PWM or resistance Dimmer Cautions Before commencing any installation or maintenance work, please disconnect the power supply from the utility. Ensure that it cannot be reconnected inadvertently! Keep proper ventilation around the unit and do not stack any object on it. Also a 101 cm clearance must be kept when the adjacent device is a heat source. Mounting orientations other than standard orientation or operate under high ambient temperature may increase the internal component temperature and will require a derating in output current. Current rating of an approved primary /secondary cable should be greater than or equal to that of the unit. Please refer to its specification. For LED power supplies with waterproof connectors, verify that the linkage between the unit and the lighting fixture is tight so that water cannot intrude into the system. For dimmable LED power supplies, make sure that your dimming controller is capable of driving these units.pwm series require 0.1mA each unit. Tc max. is identified on the product label. Please make sure that temperature of Tc point will not exceed limit. DO NOT connect "DIM to V". Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30 minutes. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must requalify EMC Directive on the complete installation again. For more information about installation, please refer to www.meanwell.com/webnet/search/installationsearch.html for details.