PB-1000 series. 1000W Intelligent Single Output Battery Charger SPECIFICATION MODEL PB PB PB V 28.8V 57.6V 13.

Transcription

1 .. 000W Intelligent Single Output attery Charger P000 series SPECIFICTION MODEL OUTPUT INPUT PROTECTION FUNCTION ENVIRONMENT SFETY & EMC (Note ) OTHERS NOTE OOST CHRGE VOLTGE FLOT CHRGE VOLTGE OUTPUT CURRENT RECOMMENDED TTERY 00 ~ 600h CPCITY(MP HOURS)(Note 3) TTERY TYPE LEKGE CURRENT FROM TTERY (Typ.) VOLTGE RNGE FREQUENCY RNGE EFFICIENCY (Typ.) POWER FCTOR (Typ.) C CURRENT (Typ.) INRUSH CURRENT (Typ.) LEKGE CURRENT OVER VOLTGE OVER TEMPERTURE WORKING TEMP. WORKING HUMIDITY STORGE TEMP., HUMIDITY TEMP. COEFFICIENT VIRTION SFETY STNDRDS WITHSTND VOLTGE ISOLTION RESISTNCE EMI CONDUCTION & RDITION HRMONIC CURRENT EMS IMMUNITY P000 P0004 P V 8.8V 5.6V 3.8V Open & Sealed Lead cid <m 0 ~ 64VC ~ 30VDC 4 ~ 63Hz 85% 0.5/30VC /5VC 5/5VC <3.5m / 40VC 0.8/5VC at full load 5./30VC 50/30VC.6V 55.V ~ 350h 60 ~ 5h 88% 8% 6 ~ 8V 3 ~ 35V 64.5 ~ 6.5V Protection type : Shut down o/p voltage, repower on to recover 80 5 (V), 85 5 (4V,48V) (TSW: detect on heatsink of power transistor) 85 5 (V),5 5 (4V,48V) (TSW : detect on heatsink of o/p diode) Protection type : Shut down o/p voltage, recovers automatically after temperature goes down SHORT CIRCUIT REVERSE POLRITY YES, protected by internal circuit YES, protected by internal circuit REMOTE Open: Normal work Short: Stop TTER NKS banks ( & ) FST CHRGE / 8 stage selectable CHRGER OK Relay contact rating(max.): 30V/ resistive ; "Short" when the unit is working properly, "Open"when the unit is failure or the protection function is activating OUTPUT OK Relay contact rating(max.): 30V/ resistive ; "Short" when the battery is full, "Open" when the battery is still charging TEMPERTURE COMPENSTION y NTC, compensate both banks at the same time 0 ~ 60 (Refer to output load derating curve) 0 ~ 0% RH noncondensing 40 ~ 85, 0 ~ 5% RH 0.05%/ (0 ~ 50 ) 0 ~ 500Hz, G 0min./cycle, 60min. each along X, Y, Z axes UL6050, TUV EN6050 approved I/PO/P:3KVC I/PFG:.5KVC O/PFG:0.5KVC I/PO/P, I/PFG, O/PFG:00M Ohms / 500VDC / 5 Compliance to EN550 (CISPR) Compliance to EN60003,3 / 0% RH Compliance to EN60004,3,4,5,6,8,; ENV5004, EN5504, light industry level, criteria MTF.4Khrs min. MILHDKF (5 ) DIMENSION PCKING *84*0mm(L*W*H) 3.5Kg; 4pcs/5Kg/.83CUFT File Name:P000SPEC 00040

2 W Intelligent Single Output attery Charger P000 series Mechanical Specification Case No. 804 Unit:mm ON OFF ON/OFF SWITCH INLET ir flow direction C INPUT Curve Start Charge Voltage Vboost Control Pin No. ssignment() : HRS DF0DPDS or equivalent Pin No. ssignment Pin No. ssignment Mating Housing Terminal, RY3 8 NTC(5K ) 3,4 RY4 RC HRS DF0DS HRS DF**SC 5,6 RY5 0 RC or equivalent or equivalent Charge Current Constant Current Constant Voltage 00% 0% RY3 : ank OK RY4 : ank OK RY5 : Charger OK NTC / : Temperature sense RC / RC: Remote ON/OFF stage stage attery Full Pulse Soft Start Constant Current Constant Voltage nalysis Recondition Float Maintain Charge Voltage Charge Current stage stage stage 3 stage 4 stage 5 stage 6 stage stage 8 File Name:P000SPEC 00040

3 000W Intelligent Single Output attery Charger P000 series lock Diagram PFC : 5KHz PWM fosc : 60KHz I/P EMI FILTER CTIVE INRUSH CURRENT LIMITING RECTIFIER & PFC POWER SWITCHING RECTIFIER & FILTER NK (V) NK (V) PFC UX POWER PWM FN OTP CURRENT DETECTION MCU REVERSE DETECTION /8 STGE SELECT REMOTE RC ank OK RY3 ank OK RY4 Charger OK RY5 Derating Curve The Function of LEDs attery Fail attery Full Red 60 LOD (%) 40 0 Function Description of Pin No. Function Description, 3,4 5,6 RY3 RY4 RY5 Relay contact rating(max.) : 30V/ resistive. ; "Short" when the battery is full, "Open" when the battery is still charging. Relay contact rating(max.) : 30V/ resistive. ; "Short" when the battery is full, "Open" when the battery is still charging. Relay contact rating(max.) : 30V/ resistive. ; "Short" when the unit is working properly, "Open" when the unit is failure or the protection function is activating.,8, (HORIZONTL) Temperature sensor comes along with the charger can be connected to the unit to allow temperature compensation of the / RTH charging voltage. If the temperature sensor is not used, the charger still works normally. RC / RC MIENT TEMPERTURE ( ) Turn the output on and off by electrical or dry contact between pin 0 (RC) and pin (RC), "Open" : Normal work, "Short" : Stop charging File Name:P000SPEC 00040

4 000W Intelligent Single Output attery Charger P000 series Function Manual.Remote Control The charger can be turned ON/OFF by using the "Remote Control" function. etween RC(pin0) and RC(pin) SW Open SW Short Charger ON OFF RY3 RY3 RY4 RY4 RY5 RY5 RTH RC 0 RC SW attery attery.two attery anks The charger may be hooked up two battery banks ( and/or ). Connect the battery bank(s) as below. If you are connecting battery banks in the same time, keep in mind that they must share a common ground. attery attery attery attery File Name:P000SPEC 00040

5 000W Intelligent Single Output attery Charger P000 series 3. or 8 stage Select The charger features user selectable or 8 stage charging. The charging profile is selected by moving the slide switch on the back panel. Switch mode RY3 RY3 Turn right Turn left stage charging 8 stage charging RY4 RY4 RY5 RY5 RC RTH RC 0 attery attery 4.Charger OK Relay(RY5) Charger Normal work Failure or the protection function is activating etween pin5 and pin6(ry5) RY3 RY3 RY4 RY4 RY5 RY5 RTH RC RC 0 RY5 attery attery 5.Output OK Relay(RY3 & RY4).ank OK (RY3) ank etween pin and pin(ry3) attery Full.ank OK (RY4) ank etween pin3 and pin4(ry4) RY3 RY3 RY4 RY4 RY5 RY5 RTH attery Full RC RC 0 RY4 attery attery RY3 6.Temperature Compensation Temperature sensor comes along with the charger can be connected to the unit to allow temperature compensation of the charging voltage. If the temperature sensor is not used, the charger still works normally. RY3 RY3 RY4 RY4 RY5 RY5 RTH RC RC 0 attery attery NTC The temperature sensor can either be attached to the battery or placed in its surrounding environment. File Name:P000SPEC 00040