Product catalogue 2012 rev 1 Smart indoor climate!.2
Table of contents Wireless control system examples... p. 4 Wireless rooom temperature control systems... p. 5-7 Wireless room temperature control systems Room temperature control system examples... p. 8-9 Thermostats and room temperature controllers... p. 10-13 Room temperature controllers ontrol unit system examples... p. 14 ontrol units... p. 15-16 ontrol units Room units E121, E122, E123, E201 and E202... p. 17 Room units onfiguration tools H202 and H203... p. 18 onfiguration tools Sensors G9, G21, G22, G23 and G24... p. 19 Sensors GIR-1, GIR-2 and G-O2... p. 20 Sensors Actuators and valve adapters... p. 21 Actuators and valve adapters Damper actuators... p. 22 Damper actuators 2-port control valves with firm and adjustable kvs-value... p. 23 2-port valves 3-port valves... p. 24 3-port valves Shut off, trim, terminal and differential pressure valves... p. 24 Misc. valves Valve connections... p. 25 Valve connections Transformers and cables for Zone ontrols systems... p. 26 Transformers and cables Relay units for Zone ontrols systems... p. 27 Relay units
SET wireless Systems system examples System example 1 WA alt. 230V A These are only system examples of how the products can be used. ontact us for additional examples or functions. WRU WA alt. 230V A ontrol cooling and heating in sequence with room unit WRU and actuator unit WA. System example 2 WF 230V A WRU-F Key card switch Window contact switch WA Floor temperature sensor ontrol cooling, heating, fan speed and heated floor in sequence with room unit WRUF, control unit WA and WF. The key card switch/window contact switches the current operation mode between economy and comfort operation mode. The control unit WA controls the heated floor dependeing of the total power requirement of the room. p. 4
WIRELESS systems Description, room unit WRU Wireless room unit for measuring the room temperature and adjusting the set-point. Available for fan speed control, timer forced ventilation, and without set-point knob. Radio communication. Easy installation. The solar cell powered room unit is without any cables. Powered by solar cell or. Built in temperature sensor. Available in aluminium or steel grey enclosure, standard colour is white. E approved. WRU WRUF WRUT Room unit solar cell powered Room unit without set-point knob WTS-01.000 WTS24-01.000 Room unit WRU-01.000 WRU24-01.000 Room unit with button for fan speed control WRUF-01.000 WRU24F-01.000 Room unit with timer button WRUT-01.000 WRU24T-01.000 Description, actuator unit WA Wireless actuator unit to control one actuator on a control valve Radio communication. Powered with or 230V A. To be used with actuators in the AT-series. E approved. Actuator unit 230V A Actuator unit WA-01.000 WA230-01.000 p. 5
WIRELESS SystemS Description, control unit WA ontrol unit for the wireless system, control cooling, heating and ventilation. For controlling of chilled ceilings, radiators etc. Effective and energy saving control. PI-control. ooling and heating in sequence. Available in two performances: - WA-24... Supply voltage 24 V A, 2 digital and 1 analog output. - WA-230... Supply voltage 230 V A, 2 digital outputs. 2 inputs for e.g. temperature sensor and occupancy detector. The inputs can be adjusted between different levels and purposes. Automatic valve exersice. Timer function for overriding the operation mode or to force output. Wireless room unit WRU can be connected by radio communication. ontrol values can be monitored and overriden with a building management system by a gateway WSG. E approved. The control units control parametres, inputs, output signals etc. can easily be customized and installed with the WPG configuration tool. ontrol unit WA Supply voltage, 2 digital and 1 analog output Supply voltage 230V A, 2 digital outputs WA-24 WA-230 Description, control unit WF ontrol unit for the wireless system, control cooling, heating and fan speed. For controlling of fan coils, chilled ceilings, radiators etc. Effective and energy saving control. PI-control. ooling and heating in sequence. Two actuator outputs (230V or 24V depending on the model WF-230-10). Three relay outputs for fan speed control (WF-230 only). One 0-10V output for fan coil control with an E-motor (WF-10 only). 2 inputs for e.g. temperature sensor and occupancy detector. The inputs can be adjusted between different levels and purposes. Automatic valve exersice. Timer function for overriding the operation mode or to force output. Wireless room unit WRU can be connected by radio communication. ontrol values can be monitored and overriden with a building management system by a gateway WSG. E approved. The control units control parametres, inputs, output signals etc. can be customized especially for an installation with the WPG configuration tool. ontrol unit WF Supply voltage, 2 digital and 1 analog output Supply voltage 230V A, 2 digital outputs WF-10 WF-230 p. 6
Wireless systems Description, gateway WSG Used for supervision, measuring and to confiure wireless products, and as a connection point for a supervision system. Radio communication. Ethernet 10/100 Mbit (RJ45). Modbus RTU over TP/IP. E-approved. Wireless gateway WSG-01.000 Description, configuration tool WPG Used with a windows P to install and configure the wireless products (WRU, WA, WF and WA). E approved. WM WPG onfiguration tool Windows program WM (enclosed with WPG) WPG-01.000 WM-01.000 p. 7
ROOM TEMPERATURE ONTROLLERS system examples System example 1 AT actuator 0-10V / (max 8 pcs total) These are only system examples of how the products can be used. ontact us for additional examples or functions. ondensation sensor G9 ontroller R102 ontroller R201 AT actuator 0-10V / (max 8 pcs total) ontrol cooling and heating in sequence with room temperature controller R102 or R201. System example 2 AT actuator (max 8 pcs total) SBA / SB damper actuator 0-10V D / Occupancy detector GIR-1 ontroller RS102 ontroller R221 AT actuator AT actuator (max 8 pcs total) ontrols cooling, heating and damper actuator in sequence with room temperature controller RS102 or R221. The occupancy detector switches the controllers operation mode between economy and comfort operation mode. Forced ventilation (2h time period) when the forced ventilation button is pressed on the controller RS102. p. 8
Room Thermostat controls with actuators Description, room thermostat R41 A analog room thermostat to control cooling and heating with on/off output signals. The room thermostat is available with terminal or modular connections. For controlling of chilled ceilings, radiators etc. ooling and heating in sequence with 24V on/off. The temperature can be adjusted from 16 to 28. The LED indicates actual operation status. Protection class IP20. Size: 77 x 77 x 27 mm. E-approved. System description The picture shows a typical system with room thermostat R41. ooling and heating in sequence with 24V on/off outputs. Maximum of 4 actuators per output. On room thermostat R41e, an external room temperature sensor can be connected if needed. 230V A Transformer Room thermostat H (External temp. sensor) 24V ooling 24V Heating The picture shows a typical system with room thermostat with modular connection and modular cable, actuator with modular contacts and D1-2 connection boxes. See product data sheet for further descriptions of modular cables and actuators. 230V A ooling and heating in sequence with 24V outputs. Maximum of 4 actuators per output. Room thermostat onnection boxes Transformer H H ooling Heating ooling Heating ARTIKELNUMMER Room thermostat R41 cooling output Heating output R41-01.000 on/off on/off R41e-01.000 (for external temp. sensor) on/off on/off R41M-01.000 (modular connection) on/off on/off Transformer for R41M T20-21M p. 9
ontrollers controls with and 0-10V actuators Description, controller R102 A digital room temperature controller for control of cooling and heating. The controllers output signal functions can easily be changed with the jumpers on the circuit board. The controller is available with terminal or modular connection. For controlling of chilled ceilings, radiators etc. Effective and energy saving control. ooling and heating in sequence with time proportional 24V on/off and/or analog 0-10V outputs. The temperature can be adjusted from 19 to 25. The LED indicates actual operating status. Protection class IP20. Size: 77 x 77 x 27 mm. E-approved and S-marked. The control parameters, inputs and output signals and limit values can be adjusted with help of a configuration unit, which connects to the controller with a modular contact under the controllers cover plate. System description The picture shows a typical system with room temperature controller R102 and its in- and outputs as they are configured on delivery. The inputs are programmable to fit different types of sensors: External temperature sensor Occupancy sensor ontact for overriding the operation mode ondensation sensor The output functions, sequences and limit values can easily be adjusted with a configuration unit H202. The room temperature controller can be ordered preinstalled with customer specific parameters. ontact Zone ontrols AB for more information. Room temperature controller ondensation sensor External temp. sensor 230V A Transformer ooling actuators H Heating actuators The picture shows a typical system with room temperature controller R102M in modular performance with modular cable, actuator with modular contacts and D1-2 connection boxes. See product data sheet for further descriptions of modular cables and actuators. The room temperature controller can be ordered preinstalled with customer specific parameters. ontact Zone ontrols AB for more information. Room temperature controller onnection box 230V A Transformer H H ooling Heating ooling Heating ontroller heating output ooling output R102-01.000 R102-02.000 0-10V D 0-10V D R102-03.000 0-10V D R102-04.000 0-10V D R102M (modular connections e.g. R102M-01.000) onfiguration unit H202-01.000 Transformer for R102M T20-21M p. 10
Description, controller RS102 A digital room temperature controller for controlling cooling and heating, with a button to force a ventilation damper to open in 2 hours. The forcing output of the damper can also be adjusted to control in sequence with the cooling output. The controllers output signal functions can easily be changed with the jumpers on the circuit board. For controlling of chilled ceilings, radiators etc. Effective and energy saving control. ooling and heating in sequence with time proportional 24V on/off and/or analog 0-10V outputs. Push-button to set the forcing function on/off. Forcing indication with LED. The temperature can be adjusted from 19 to 25. LED indicates current operation mode. Protection class IP20. Size: 77 x 77 x 27 mm. E-approved. The control parameters, inputs and output signals and limit values can be adjusted with help of a configuration unit, which connects to the controller with a modular contact under the controllers cover plate. ONTROLLERS ONTROLs AND 0-10V ATUATORS AND FORED VENTILATION System description The picture shows a typical system with room temperature controller RS102 and its in- and outputs as they are configured on delivery. The input is adapted for an optional temperature sensor, connected when in need of an optimal placement of a room temperature sensor. The outputs functions, sequences and limit values can easily be adjusted with a configuration unit H202. The room temperature controller can be ordered preinstalled with customer specific parameters. ontact Zone ontrols AB for more information. Room temperature controller External temp. sensor 230V A Transformer D Damper actuator ooling actuator H Heating actuator ontroller heating output ooling output Forced ventilation RS102-01.000 0-10V D onfiguation unit H202-01.000 p. 11
ontroller with display controls with and 0-10V actuators Description, controller R221 and R222 A digital room temperature controller for controlling cooling and heating. Modbus communication or stand alone. The control parametres, input and output signals and control limitation values can be adjusted directly with the display and buttons. No separate configuration unit is necessary. The R222 controller is designed to control the fan speed with the 0-10V output via a 3 stage relay or an E motor in 3 steps, or seamless. For controlling of chilled ceilings, radiators etc. PI-control, effective and energy saving. ooling and heating in sequence with time proportional 24V on/off and/or analogue 0-10V output. an also control raise/lower actuators (3 point control). The temperature can be adjusted from 19 to 25. The display indicates actual operating status. Protection class IP30. Size : 89 x 89 x 26mm. E approved System description The picture shows a typical system with room temperature controller R221 and its in- and outputs as they are configured on delivery. The inputs are programmable to suit different types of sensors: External temperature sensor Occupancy sensor ontact for overriding the operation mode ondensation sensor The output functions, sequences and limit values can easily be adjusted with the help of the controllers buttons and display. The room temperature controller can be ordered preinstalled with customer specific parameters. ontact Zone ontrols AB for more information. The picture shows a typical system with room temperature controller R222 and its in- and outputs as they are configured on delivery. The inputs are programmable to suit different types of sensors: External temperature sensor Occupancy sensor ontact for overriding the operation mode ondensation sensor The output functions, sequences and limit values can easily be adjusted with the help of the controllers buttons and display. The 0-10V output can be activated to control a 0-10V relay for fan speed control, an E motor in 3 stages or seamless. The room temperature controller can be ordered preinstalled with customer specific parameters. ontact Zone ontrols AB for more information. R221-01.000 Room temperature controller Modbus Timer switch to force output 230V A External temperature sensor Transformer ooling ( 0-10V D ) ooling ( ) H Heating ( ) G Heating ( ) R222-01.000 Room temperature controller 230V A Transformer F Modbus Timer switch to force output External temperature sensor Seamless, or 3 stage output for fan speed control (0-10V D) ooling ( ) H Heating ( ) H Heating ( ) ontroller R221-01.000 R222-01.000 (for 0-10V D fan speed control) p. 12
ONTROLLER WITH DISPLAY ONTROLS WITH AND 0-10V ATUATORS Description, controller R204-90 A digital room temperature controller with an infrared receiver for built-in mounting in e.g. chilled beams. The infrared receiver in the controller makes it possible to easily adjust values when the controller has been mounted in an unapproachable place, e.g. the ceilings. hanges of walls placements does not affect the zoning of the chilled beams. An external sensor measures the room temperature in the ejected air. ontrol parameters, inputs and so on can be adjusted with the help of the controllers display and a remote control. For controlling of chilled ceilings, radiators etc. Effective and energy saving control. Input for a forcing button. Automatic valve exercise. Possibility to block IR-receiving with a 4-digit code. ooling and heating with several steps in sequence (see system description). The temperature can be adjusted from 19 to 25. The display indicates actual operating status. Protection class IP30. Size: 89 x 89 x 26 mm. E-approved. System description R204-90.000 Room temperature controller 230V A Transformer Switch to force cooling 1 (0-10V). External temperature sensor ooling 1 ( ) ooling 1 ( 0-10V D ) ooling 2 ( ) R204-90 is available in three different standard performances. The pictures shows all three systems and its in and outputs as they are configured on delivery. The output functions, sequences and limit values can easily be adjusted with the help of the controllers display and a remote control.. The room temperature controller can be ordered pre-installed with customer specific parameters. ontact Zone ontrols AB for more information. R204-90.001 Room temperature controller Switch to force cooling 1 (0-10V). External temperature sensor 230V A Transformer H ooling 1 ( 0-10V D ) ooling 2 ( ) Heating ( ) R204-90.002 Room temperature controller Switch to force cooling 1 (0-10V). External temperature sensor 230V A Transformer ooling 1 ( ) ooling 2 ( ) Room temperature controller output 1 output 2 output 3 R204-90.000 ooling 1 ( 24V ) ooling 1 (0-10V) ooling 2 (24V) R204-90.001 ooling 1 ( 0-10V ) ooling 2 ( 24V ) Heating ( 24V ) R204-90.002 ooling 1 ( 24V ) ooling 2 ( 24V ) - Remote control H11 p. 13
ontrol units System examples System example 1 SBA / SA damper actuator 0-10V D SBA / SA damper actuator 0-10V D These are only system examples of how the products can be used. ontact us for additional examples or functions. Room unit E201 AT actuator (max 8 pcs total) ondensation sensor ModBus 221 Room unit E101 Room unit E123 AT actuator AT actuator Occupancy detector GIR-1 O2 sensor G-O2 AT actuator (max 8 pcs total) For controlling of cooling, heating and ventilation in sequence with control unit 221 and room unit E201, E121 or E123. The occupancy detector contact switches the current operation mode between economy and comfort operation mode. The O2-sensor forces the damper actuators to open for ventilation when the O2 levels are too high. The forced ventilation can also be controlled by a timer with room unit E123. The system can be connected to Modbus. System example 2 SBA / SB damper actuator 0-10V D / Room unit E202 AT actuator ModBus Room unit E122 222 AT actuator RL203 Fan coil Heated floor in the bathroom AT actuator 0-10V D Key card switch GK-01 Window contact switch Floor temperature sensor G231 For controlling of cooling, heating, ventilation and a fan coil in sequence with control unit 222 and room unit E202 or E122. The key card switch/window contact switches the current operation mode between economy and comfort operation mode. The damper actuator output is only active if the controller is in the comfort operation mode. The control unit 222 with the floor temperature sensor controls the heated floor depending of the total power requirement of the room. The system can be connected to Modbus. p. 14
ONTROL UNITS ONTROLS WITH AND 0-10V ATUATORS Description, control unit 221 och and 222 Intelligent and flexible control units for most types of applications. Effective and energy saving control. ommunication via ModBus or stand alone. The control units control parameters, input and output signals etc. can be adjusted with a room unit E201/E202 or a configuration unit H203. Used as a supply unit for room units in the E series and control unit for actuators. Galvanic isolated communication circuit for ModBus communication The in- and outputs can be adjusted between different signal levels and purposes 3 programmable inputs for different types of sensors 4 programmable outputs: 2 pcs. of outputs + 2 pcs. of 0-10V outputs Automatic valve exercise Timer function for overriding the operation mode or to force outputs Pluggable terminals for easier installation One control unit can control upto 16 slave control units. 221 is expandable with relay unit RL203 to control dampers in 3 steps. It can also control fan speed with the 0-10V output e.g. E motor in 3 steps or seamless. 222 is expandable with relay unit RL203 to control fan speeds in 3 steps. Supply voltage:. Protection class IP44. Size: 80 x 122 x 40 mm. E approved. The room units in the E series are available in different performances for various site specific functions. System description The picture shows the control units all available in- and outputs as they are configured on delivery. All inputs are programmable to fit different types of sensors, e.g: Room unit I1.External temp. sensor Temperature sensor control (control 0-10V or thermistor). Secondary temperature sensor Occupancy sensor ontact for overriding the operation mode General 0-10V sensor ondensation sensor The inputs can also be programmed to directly influence one of the outputs. Modular cable 220V A Transformaer ontrol unit H H I2.ontact/Economy control I3.ondensation sensor ModBus 24V output (cooling) 24V output (heating) 0-10V output (cooling) The control units outputs are programmable to fit most types of actuators. The output functions, sequences and limit values can easily be adjusted with a room unit E201 or a configuration unit H203. The control unit can be expanded with a relay unit RL203 to control damper outputs or fan speeds: 221 and RL203 are used to control dampers up to three steps in sequence. It can also control fan speed with the 0-10V ouput e.g. an E motor. 220V A Transformer Relay unit 0-10V output (heating) Fan- or damper output 1 Fan- or damper output 2 Fan- or damper output 3 222 and RL203 are used to control fan speeds upto three steps in sequence. The control unit can be ordered pre-installed with customer specific parameters. ontact Zone ontrols AB for more information. ontrol unit 221-01.000 for chilled ceilings, radiators, dampers etc. 222-01.000 for fan coil control Relay unit to control dampers or fan speeds in 3 steps RL203-01.000 p. 15
ONTROL UNIT ONTROLS WITH TUATORS Description, control unit 202 A control unit for controlling cooling and heating. ontrol unit 202 can be used together with relay unit RL203 to control fan speeds in three steps. Effective and energy saving control. The control units control parameters, input and output signals etc. can be adjusted with a room unit E201/E202 or a configuration unit H203. Used as a supply unit for room units in the E series and control unit for actuators. 202 is expandable with relay unit RL203 to control fan speeds in three steps. The in- and outputs can be adjusted between different signal levels and purposes. 1 programmable input for different types of sensors. 2 programmable outputs. Automatic valve exercise Timer function for overriding the operation mode or to force outputs. Supply voltage:. Protection class IP44. Size: 80 x 122 x 40 mm. E-approved. The room units in the E series are available in different performances for various site specific functions. See next page. System description The picture shows the control units all available in- and outputs as they are configured on delivery. The input is programmable to fit different types of sensors, e.g: Room unit External temperature sensor External temperature sensor Occupancy sensor ontact for overriding the operation mode ondensation sensor The control units outputs are programmable to fit most types of 24V actuators. The output functions, sequences and limit values can easily be adjusted with a room unit E201/E202 or a configuration unit H203. Modular cable 220V A Transformer ontrol unit H 24V output (cooling) 24V output (heating) The control unit can be ordered pre-installed with customer specific parameters. ontact Zone ontrols AB for information. Relay unit Fan speed 1 Fan speed 2 Fan speed 3 ontrol unit 202-01.000 for chilled ceilings, radiators, fan coil controls etc. 202B-01.000 (controls the fan speed only in cooling mode) Relay unit to control fan speeds in three steps RL203-01.000 p. 16
ROOM UNITS TO ONNET TO THE ONTROL UNIT Description, room unit E121 A room unit with knob to control temperature. It has a built-in temperature sensor which measures the current room temperature. The LED indicates current function. In need of cooling a blue LED is lit, red in need of heating and is off at dead zone. If a condensation sensor is connected the blue LED flashes at condensation. onnects to control unit 221 with a 4-way cable (K400) Protection class IP30. Size: 77 x 77 x 27 mm. E approved. Room unit E121-01.000 Description, room unit E122 A room unit with knob to control temperature and a button to control fan speed or damper output. It has a built-in temperature sensor which measures current room temperature. The LEDs indicates current function. If a condensation sensor is connected the blue LED flashes at condensation.. The LEDs closest to the button indicates actual fan/damper function. onnects to control unit 221 or 222 with a 4-way cable (K400) Protection class IP30. Size: 77 x 77 x 27 mm. E approved. Room unit E122-01.000 Description, room unit E123 A room unit with knob to control temperature and a button to control time of timer, e.g. forced ventilation. It has a built-in temperature sensor which measures current room temperature. The LEDs indicates current function. If a condensation sensor is connected the blue LED flashes at condensation. The LEDs closest to the button indicates remaining time of timer. onnects to control unit 221 or 222 with a 4-way cable (K400) Protection class IP30. Size: 77 x 77 x 27 mm. E approved. Room unit E123-01.000 Description, room unit E201 / E202 E201 is a room unit with display and buttons to control room temperature. Built-in menu system to control all of the control unit s functions. It has a built-in temperature sensor which measures current room temperature. The display shows current function, temperatures and set points. E202 also has an extra button function to adjust fan speed (or damper outputs). onnects to control unit 221 or 222 with a 4-wire modular cable (K43) Protection class IP30. Size: 89 x 89 x 26 mm. E-approved. Room unit E201-01.000 E202-01.000 (to control fans or dampers). p. 17
ONFIGURATION UNITS for configuration of ontrollers and control units Description, configuration unit H202 / H203 Used for setting control parameters, input and output signals etc. The configuration units are connected to a digital controller without display or to a room unit without display. The connection to the controller or room unit is done with a modular contact. H202 is used together with room temperature controller R102 H203 is used together with room unit E121-E123, or connected directly to a control unit. Quick connection with a modular contact. Protection class IP30. Size: 89 x 89 x 26 mm. E-approved. onfiguration units H202-01.000 for R102 H203-01.000 for E121-E123 or control unit 221 and 222 p. 18
Duct sensor Duct sensors can be used when you need to measure the temperature of the supplied or ejected air. It is available in performances for both the analog and digital controllers, see order number below. Sensors FoR controllers and control units Sensor G3 G23 suitable for (to analog control systems) (to digital control systems) Room temperature sensor Room temperature sensors can be used when the temperature shall be measured in a room, to control mean value, for instance, or if you want the controller to be hidden. It is available in performances for both the analog and digital controllers, see order number below. Sensor G4 G24 suitable for (to analog control systems) (to digital control systems) ondensation sensor ondensation sensors can be used if you want the output signal of the cooling to be blocked or that a relay shuts at condensation. The condensation sensor is adhesive and should be mounted on the underside of pipes or other places where condensation may occur. Sensor G9 Pipe surface temperature sensor The pipe surface temperature sensor can be used when the water temperature shall be measured in systems with a heating controller. The pipe surface temperature sensor shall be mounted on the top side of the pipe with the included stripe. Sensor G22-01.000 p. 19
SENSORS FoR controllers and control units Occupancy detector For occupancy detection in office rooms or other indoor areas. Designed for mounting at the ceiling. The occupancy detector reacts on sudden temperature changes in the room. Adjustable on/off-delay. E approved. Occupancy detector GIR-1 Occupancy detector For occupancy detection in office rooms or other indoor areas. Designed for wall mounting. The occupancy detector reacts on sudden temperature changes in the room. Adjustable on/off-delay. E approved. Occupancy detector GIR-2 O2 sensor For measuring of O2 and temperature levels in offices, conference rooms etc. O2 sensors can be used with the control units to force, or control exhaust and supply air dampers when the O2 levels are too high. The sensor measures O2 levels between 0-2000 ppm, and the output voltage 0-10V in proportion to the rooms ppm value. The O2 sensor also has a built in active temperature sensor and the output voltage is 0-10V in proportion to the room temperature. Available in performaces with or without display and with Modbus communication. The O2 sensors are self calibrating. Also available in special versions for VAV control. ontact Zone ontrols AB for more information. E approved. O2 sensors Without display With display O2 sensor without Mobus G-O2 G-O2D O2 sensor with Modbus G-O2M G-O2DM p. 20
ATUATORS AND VALVE ADAPTERS Actuators Actuator AT with many connection possibilities and functions: Order number Function Performace Picture AT-0 N Without cable A AT-1 N With 1 m cable A AT-2 NO With 1 m cable A AT-3 230V A N With 1 m cable A AT-4 230V A NO With 1 m cable A A Accessories Picture AT-K1 1 m connection cable to AT-0 AT-K0-10 0-10V cable to AT-0, 2 m AT-K0-10-5M 0-10V cable to AT-0, 5 m AT-K10-0 10-0V cable to AT-2, 2 m AT-28MMA Bayonet nut for MMA actuators B 0550390101 Bayonet nut for M28x1,5mm actuators 0550390001 Bayonet nut for M30x1,5mm actuators D B D Valve adapters To get the actuators to fit on valves of different brands you sometimes need an valve adapter. Zone ontrols have valve adapters to most of the existing valves on the market. For actuators with M28 x 1,5 mm thread fitting: Order number onnection Inner diameter Fits valve: 9712-24.700 Hex. set screw 20 mm Danfoss RAN 9711-24.700 Hex. set screw 25,5 mm Danfoss RAVL 9810-24.700 Hex. set screw 34 mm Danfoss RAV 9712-24.720 Thread M20 x 1 AGA 9710-41.700 Thread M30 x 1,5 TA/HEIMEIER 9711-28.700 Thread M28 x 1,5 TA RVT 9710-55.700 Thread M28 x 1,5 EPEON For actuators with M30 x 1,5 mm thread fitting: Order number onnection Inner diameter Fits valve: 9702-24.720 Thread M20 x 1 AGA 9702-24.700 Hex. set screw 20 mm Danfoss RAN 9700-24.700 Hex. set screw 25,5 mm Danfoss RAVL 9800-24.700 Hex. set screw 34 mm Danfoss RAV 9700-41.700 Thread M28 x 1,5 Markaryd 2001-20.700 Thread M30 x 1,5 Landis & Gyr 9701-28.700 Thread M28 x 1,5 TA RVT/TRV 9700-55.700 Thread M28 x 1,5 EPEON p. 21
DAMPER ATUATORS Damper actuator SA Rotation angle SA2224 is designed for use on smaller round dampers but can also be used in other dampers with a maximum area of 0.2 m2, however, the safety margin has to be to the maximum rotary torque of 2 Nm. The motor rotates counter clockwise as seen from shaft side and is not reversible. It is delivered in a closed position. Several damper actuators can be connected in parallel. Different mounting plates are available for different damper solutions. Damper actuator Torque control voltage SA2224 2 Nm Damper actuator SB SB2 is a series of damper actuators that are available in two sizes, 2 and 4 Nm. The supply voltage is 24 V A/D or 230 V A. The damper actuators has synchronous motors for reversible control and magnetic end position break. The W-W switch changes the rotation direction. Push-button for gearing release. Damper actuator Torque control voltage SB2224 / SB2424 2 / 4 Nm SB22230 / SB24230 2 / 4 Nm 230V A SBA224 / SBA424 2 / 4 Nm 0-10V D Damper actuator S S2 is a series of damper actuators that are available in two sizes, 6 and 10 Nm. The supply voltage is 24 V A/D or 230 V A. The SA damper actuator can be controlled with a 0-10V output signal. The damper actuators has synchronous motors for reversible control and magnetic end position break. The W-W switch changes the rotation direction. Push-button for gearing release. Damper actuator Torque control voltage S2624 / S21024 6 / 10 Nm S26230 / S210230 6 / 10 Nm 230V A SA624 / SA1024 6 / 10 Nm 0-10V D Damper actuator SF SF2 is a 2-position damper actuator with spring-return. The supply voltage is 24 V A/D. The damper actuators has synchronous motors and magnetic end position break. Manual opening and locking of the spring-return. Damper actuator Torque control voltage SF2824 8 Nm SF21624 16 Nm p. 22
VALVES 2 port valves with firm kvs value The valves are available in different performances, sizes and with various kvs-values, dependent on the size of the pipe. More information of the valves and pressure drop diagrams are available on our website www.zc.se. A B Ord.number onnection Type Pic kvs-values Thread (actuators) 2201 DN10 - DN20 Angled A 1,25 / 1,35 M30x1,5 mm 2202 DN10 - DN32 Straight B 1,25 / 5,80 M30x1,5 mm 2242 DN15 - DN20 Straight 2,50 / 3,60 M30x1,5 mm M002 DN10 - DN15 Straight D 1,20 / 1,40 M28x1,5 mm M242 DN10 - DN20 Straight E 2,50 / 3,90 M28x1,5 mm D E 2 port valves with adjustable kvs value The valves are available in different performances, sizes and with various kvs-values, dependent on the size of the pipe. More information of the valves and pressure drop diagrams are available on our website www.zc.se. Ord.number onnection Type Pic kvs-values Thread (actuators) 3511 DN10 - DN15 Angled A 0,05-0,73 M30x1,5 mm 3512 DN10 - DN20 Straight B 0,05-0,73 M30x1,5 mm M501 DN10 - DN20 Straight 0,01-1,20 M28x1,5 mm M502 DN10 - DN20 Straight D 0,01-1,20 M28x1,5 mm DZR* M552 DN15 - DN20 Straight E 0,01-3,60 M28x1,5 mm * ) DZR = Dezincification resistant brass A B D E p. 23
VALVES 3 port valves A The valves are available in different performances, sizes and with various kvs-values, dependent on the size of the pipe. More information of the valves and pressure drop diagrams are available on our website www.zc.se. B Ord.number onnection Pic kvs-values Thread (actuators) 4139-4141 DN15 A 1,45 M m30x1,5 mm 4160 DN15 - DN25 B 2,47 / 5,12 m30x1,5 mm M139 DN15 1,50 M m28x1,5 mm M160 DN15 - DN25 D 2,00 / 5,00 m28x1,5 mm D A Other valves B The valves are available in different performances, sizes and with various kvs-values, dependent on the size of the pipe. More information of the valves and pressure drop diagrams are available on our website www.zc.se. Trim valves Ord.number onnection Type Pic kvs-values 0352 DN10 - DN20 Straight A 0,09-1,31 M312 DN10 - DN32 Straight B 0,03-1,30 D Shutting valve Ord.number onnection Type Pic kvs-values 0600 DN10 - DN20 Straight 6,00-14,00 E Differential pressure valve Ord.number onnection Type Pic 5501 DN20 - DN32 Angled D Terminal valve TBV- Ord.number onnection Type Pic kvs-values Thread (actuators) 1502 DN15 - DN20 Angled E 0,22-3,4 M30x1,5 mm p. 24
VentilKOPPLINGAR onnections for valves 2001-4160 onnections, valves manufactured by Heimeier ( ord.nr from 2001-4160 ). A Ord.number onnection ø pipe Pic Type 4160-02.010 DN15 1/2 A Straight, thread connection and nut 4160-03.010 DN20 3/4 A Straight, thread connection and nut 4160-04.010 DN25 1 A Straight, thread connection and nut 2001-10.351 DN10 10mm B Pressure screw and cone 2002-10.351 DN15 10mm B Pressure screw and cone 2002-12.351 DN15 12mm B Pressure screw and cone 2001-15.351 DN15 15mm B Pressure screw and cone B 1300-12.DN10 DN10 12mm Pressure nut and cone 1300-10.351 DN15 10mm Pressure nut and cone 1300-12.351 DN15 12mm Pressure nut and cone 1300-15.351 DN15 15mm Pressure nut and cone onnections for valves M002 - M552 onnections, valves manufactured by Markaryd ( ord.nr from M002 - M552 ). Ord.number onnection ø pipe Pic Type M141-01.010 DN10 - A Straight, thread connection and nut M141-02.010 DN15 - A Straight, thread connection and nut M141-02.910 DN15 - A Straight, thread connection and nut DZR* M141-03.010 DN20 - A Straight, thread connection and nut M151-01.010 DN10 - B urve and nut M151-02.010 DN15 - B urve and nut M151-03.010 DN20 - B urve and nut M001-10.351 DN10 10mm Pressure screw and cone M001-12.351 DN10 12mm Pressure screw and cone M002-12.351 DN15 12mm Pressure screw and cone M002-15.951 DN15 15mm Pressure screw and cone DZR* M301-12.351 DN10 12mm D Pressure nut M301-15.351 DN10 15mm D Pressure nut M302-15.951 DN15 15mm D Pressure nut DZR* M002-15.852 DN15 15mm E Push-on connection M302-15.852 DN15 15mm E Push-on connection A B onnections for 3-port valves: M312-10.351 DN15 10mm F Pressure nut M312-12.351 DN15 12mm F Pressure nut M313-12.351 DN20 12mm F Pressure nut M313-22.351 DN20 22mm F Pressure nut D * ) DZR = Dezincification resistant brass F E p. 25
Transformers and ABLES transformers and ABLES for zone controls systems Transformers All transformers are supplied with 230V A. E approved Technical data T20 T28 T40 T60 T120 T220 Supply voltage 230V A 230V A 230V A 230V A 230V A 230V A Output voltage Power 20 VA 28 VA 40 VA 60 VA 120 VA 220 VA Fuse, secondary pt 40 PT 25 1,6 A 2,5 A - - Fuse, primary - - - - 0,7 A 1,5 A onnection, primary Wall socket able Terminal Terminal Terminal Terminal onnection, secondary able able Terminal Terminal Terminal Terminal Protection class IP44 IP44 IP44 IP44 IP44 IP44 Transformer cabinet SK10 The transformer is supplied with 230V A. E approved. Technical data Supply voltage...230v A Output voltage...4 x Power...250 VA Automatic fuse...10 A onnection, primary...terminals for cable 2,5 mm 2 onnection, secondary...terminals for cablel 2,5 mm 2 Size (w x h x d)...240 x 290 x 115 ables and accessories ables can be ordered in different performances depending on lenght, number of conductors and colours. Standard colour is white We recommend that modular cables used for our products are purchased from us, or made from parts recommended by us, so that a correct function can be guaranteed. onnection cable from a control unit to a room unit and communication cable for modbus Order number Areas of use # of conductors able type olour K400 onnection cable 4 pcs. (2 pairs) Twisted pair/unshielded White K410 ommunication cable 4 pcs. (2 pairs) Twisted pair/unshielded Grey Specify cable lenght after order number, e.g. K400-3M (3 meters). They are delivered pre-cutted (not peeled) from roll. Modular cable for connecting control unit 221/222 with room unit E201 Technical data K43 # of conductors, cable 4 # of conductors, modular contact 4/4 Specify cable length after order number, e.g. K43-3M (3 meters) Extension jacks for modular cables Technical data KR-4/4 KY-4/4 KR-6/6 KY-6/6 KR-8/8 KY-8/8 Type Straight Y-unit Straight Y-unit Straight Y-unit onnections 4/4+4/4 4/4+4/4+4/4 6/6+6/6 6/6+6/6+6/6 8/8+8/8 8/8+8/8+8/8 p. 26
relay UNITS Relay units Relay units for digital and analog systems onnections...terminals Protection class...ip44 Size...80 x 122 x 40 mm Relay unit RL203 is used together with the control units in the 200-series to control the fan speeds or dampers in three steps. Demands supply voltage and control signal from control unit. E approved. L RY1 RY2 RY3 Relay 1 Relay 2 Relay 3 Relay unit RL203-01.000 Relay unit RL1 has one relay with different switching functions and is used to control electric heating, for instance. The relay can be controlled with or 230V A. E approved 7 2 4 3 11 12 Relay Relay unit RL1-24V RL1-230V control signal 230V A Relay unit RL3 has three relays to amplify the fan speed signals for control systems with fan speed control, or electric heating control. The relay can be controlled with or 230V A. E approved 3 11 4 5 6 Relay Relay Relay 12 13 14 Relay unit RL3-24V RL3-230V control signal 230V A Relay unit RL21 has one relay with switching function, used by systems with change-over function. The relay can be controlled with 24V A or 230V A. E approved N 8 NO 7 6 om 11 12 Relay Relay unit RL21-24V RL21-230V control signal 230V A Relay unit RL70 is used for transforming a 0-10 D signal to a potential free contact. Reuires supply voltage and a 0-10V D control signal. The relays hysteresis and contact point can be adjusted. E approved. Relay unit RL70 Relay unit RL70 is used for transforming a 0-10 D signal to three potential free contacts for fan coil speed control. Reuires 24V A supply voltage and a 0-10V D control signal. The relays hysteresis and contact pointa can be adjusted individually for all three relays. E approved. Relay unit RL80 Triac unit TR 230-400V is used to control electric heating together with Zone ontrols control systems. The triac unit is controlled with a 0-10V D pwm-signal from a controller/control unit. E-approved. Triac unit TR 230-400V p. 27
If there s a possibility - We have the solution! Zone ontrols AB develops, manufactures and markets control equipment for different types of control systems e.g. chilled ceilings, radiators, fan coils, VAV, floor heating and combinations of various system types. Our products distinguish by their flexible construction. You will find over 150 standard system solutions. There is always a solution for you as a consultant or customer, since we also customize special functions on our standard solutions. We ve been active in the same business area since the company was founded in 1990. Our long experience will be a great benefit to our customers. Our systems can be analog, digital and communicating. They control cooling, heating and air, all by requests and needs, and is suitable for most types of applications. Zone ontrols systems also contributes to effective energy saving. Zone ontrols AB is quality certified in accordance with ISO9001 and environmentally certified in accordance with ISO14001. ontact us Do you want to know more about us and our products? Please visit our website - www.zc.se You will find all up-to-date information, news and the latest data sheets available for download. Zone ontrols AB Box 64 S-137 21 Västerhaninge, SWEDEN Visiting address: Verkstadsvägen 6 S-137 37 Västerhaninge, SWEDEN Phone: +46 8 448 56 20 Fax: +46 8 777 36 55 E-mail: info@zc.se