Stainless Steel Tubular Products

Staless Steel Tubular Products r

Disclaimer This Data is dicative only and as such is not to be relied upon place of the full specification. In particular, mechanical property requirements vary widely with temper, product and product dimensions. All formation is based on our present knowledge and is given good faith. No liability will be accepted by the Company respect of any action taken by any third party reliance thereon. Please note that the Issue date shown below is no guarantee of accuracy or whether the formation here is up to date or is from the most recent references available at that date. The formation provided this publication has been drawn from various recognised sources, cludg EN Standards, recognised dustry references (prted & onle) and manufacturers data. No guarantee is given that the formation is from the latest issue of those sources or about the accuracy of those sources. Weights All weights shown this publication are for guidance only. They are calculated usg nomal dimensions and scientifically recognised densities. Please note that practice, the actual weight can vary significantly from the theoretical weight due to variations manufacturg tolerances and compositions. Copyright 5: All Rights reserved: Aalco Metals Limited. No part of this publication may be reproduced, sorted a retrieval system or transmitted any form or by any means, electronic, mechanical, recordg or otherwise without the prior written consent of the proprietor. Material supplied by the Company may vary significantly from this data, but will conform to all relevant and applicable standards. As the products detailed may be used for a wide variety of purposes and as the Company has no control over their use; the Company specifically excludes all conditions or warranties expressed or implied by statute or otherwise as to dimensions, properties and/or fitness for any particular purpose, whether expressed or implied. Advice given by the Company to any third party is given for that party s assistance only and without liability on the part of the Company. All transactions are subject to the Company s current Conditions of Sale. The extent of the Company s liabilities to any customer is clearly set out those Conditions; a copy of which is available on request. Aalco is a registered trade mark of Aalco Metals Limited. Issue No. 2 Nov 5

The Company Aalco is the UK s largest dependent multi-metals stockholder. Customers from every sector of the UK manufacturg and engeerg dustries, whether small local busesses or large multational corporations, benefit from a cost-effective sgle source for all their metals requirements. Aalco deliverg customer service and vestg capability: An ventory that cludes alumium, staless steel, copper, brass, bronze and nickel alloys all semi-fished forms Comprehensive processg services providg items cut and/or fished to customer requirements Eighteen locations brgg local service to every corner of the UK Ongog vestment technology and logistics to ensure on-time delivery No order is too large or too small and Aalco offers a responsive and competitive service for supplyg anythg from sgle item orders to major JIT contracts, tailorg this service to dividual needs. Whatever your requirement, whatever quantity, your local Aalco service centre is ready and willg to satisfy your needs. For a quotation, for further formation, more extensive technical formation, advice on product selection or to place an order, please contact your local Aalco service centre or refer to the web site www.aalco.co.uk. Service The most comprehensive stock range; the highest vestment processg equipment; local service centres nationwide; helpful, friendly, knowledgeable staff and the dustry s biggest fleet of delivery vehicles it all adds up to unbeatable service. Aalco has mataed market leadership over many years through an absolute dedication to customer service a service level that is contuously monitored and improved through key performance dicators. That s why, for reliable, on-time delivery of exactly what you want, when and where you need it, whether it s a small one-off item or a complex JIT contract, Aalco is the essential first choice. People Exceptional customer service starts with people. Aalco develops and retas high quality personnel usg a variety of house courses which cover both skills trag, product knowledge and teamwork. Every Aalco service centre has a dedicated team of people workg together to provide an unbeatable service to customers their region. Customers can expect to receive a quick and formed response to any enquiries for material or for formation. Quality Aalco takes great care when selectg manufacturg sources for its products and every mill we use is measured agast a series of predetermed quality control requirements. All products supplied by Aalco conform to the relevant BS or ternational standards. Certification can be supplied on request. Aalco service centres operate a quality manual designed to ISO900/0 requirements. Many vendor approvals and bespoke quality control systems are operated through dividual Aalco service centres. 2

Stock Range Tube Seamless to ASTM A269, imperial sizes from / O/D x 2swg to O/D x / wall grade L Seamless to ASTM A269, grades 0L & L, metric sizes 6 O/D x 0.5 wall to O/D x wall Decorative Round, Square, Rectangular Structural Square and Rectangular up to 250 Hygienic (see below) Welded Metric Nomal Internal (see below) Pipe Seamless and Welded to ASTM A from / to 2 grades 0L & L Flanges ASTM A / ANSI B.5 BS 0 Table E, Grade L BS 50 / EN 092 Raised Face, Bar Backg Flanges Alumium and Coated Mild Steel Fittgs Butt Weld Fittgs, Seamless and Welded, to ASTM A0 grades 0L & L cludg elbows, tees & reducers BSP Screwed Fittgs, grade from / to Hygienic fittgs (see below) Welded Metric Nomal Internal (see below) Hygienic Tube and Fittgs Grades 0L & L / O/D to O/D: Tube As Welded & Descaled, Annealed & Polished or Bright Annealed Bends, Fitted Bends, Tees, Reducers, Clamps & Tube Hangers Unions RJT, IDF & DIN Metric Welded Nomal Internal (ND) From O/D x.5 wall to 90 O/D x 5 wall Grades.2 (L High Molybdenum) &.07 (0L) Tube, Elbows, Tees, Reducers, Collars, End Caps, Tube Clamps & Clips Backg Flanges Alumium & Coated Mild Steel Further formation is provided by these publications, available either from your local Service Centre or at www.aalco.co.uk Product Guide Technical formation on applications, uses and specifications for staless steel, alumium, copper, brass and bronze. Stocklist A guide to the Aalco standard stock range staless steel, alumium, copper, brass and bronze. Metric A guide to the range of lightwalled nomal diameter metric staless steel tubular products used water treatment, pulp & paper and other dustries. Handrail A guide to the Aalco range of staless steel handrail/ balustrade systems comprisg tube and slotted tube plus associated fittgs.

Introduction Weld Neck Slip On Type Jotg Method General Description Used critical applications. These are circumferentially welded onto the system at their necks which means that the tegrity of the butt-welded area can easily be examed by X-ray radiography. The bores of both pipe and flange match thus reducg turbulence and erosion. This is slipped over the pipe and then fillet welded. Easy to use fabricated applications. Flanges Introduction Bld Sometimes called a blankg flange, this is used for blankg off pipeles, valves and pumps and as an spection cover. Socket Weld This is counter-bored to accept the pipe, which is then fillet welded. The bore of both the pipe and the flange are the same to ensure good flows. Screwed/Threaded This requires no weldg and is used to connect other threaded components low pressure noncritical applications. Lap Jot Rg Type Jot These are always used with either a stub end or a taft which is butt-welded to the pipe with the flange loose behd it. Thus the stub end or the taft always provides the sealg face. Easily assembled and aligned, it is favoured low pressure applications. To reduce cost these backg flanges can be supplied without a hub and/or made from coated carbon steel. This can be employed on Weld Neck, Slip On or Bld Flanges for leak-proof connection at high pressures. The seal is made by a metal rg beg compressed to a hexagonal groove on the flange face. 5-

Introduction Flanges Introduction Type Plate or Table (BS 0:962) General Description These are produced to suit Nomal Bore/NPS Pipe Sizes. They are produced from bar or plate rather than forggs and are not pressure-rated. Bld and Slip-On, flat-faced, types are readily available grades 0L and L sizes from /2 to 6 as Table D and Table E, with larger sizes and other Tables (thicknesses) made to order. These economical flanges are used for light-duty applications where corrosion resistance is the primary consideration rather than high pressure or temperature. BS EN 092 Part Also referred to as PN Flanges (Formerly BS50) These are not terchangeable with ANSI Flanges. They are readily available types 0L and L with various pressure ratgs of which 0 Bar & Bar are the most coonly used. Metric ND/DN Please refer to formation about the Metric ND product range section 7. Hygienic Please refer to formation about the Hygienics product range section 6. Flange faces Of the four choices available the most coon configurations are: For ANSI and BS EN 092 Raised Face BS 0 Flat Face. Note that this does not apply to Screwed or Lap Jot Flanges. Type Raised Face Flat Face Rg Type Jot (RJT) Tongue & Groove Small or Large To facilitate weldg General Description For leak-proof connection at high pressures Fish The fish is given as a surface roughness measured as Arithmetic Average Roundness Height (AARH). The fish requirements are stipulated by the standards, such as ANSI B.5 and are with the range 5AARH to 500AARH, which is equivalent to.2 to.5 Ra. 5-2

Introduction Pressure ratgs (The pressure ratg will also determe the dimensions of the flange Full details can be found the relevant specification.) Flange Type ANSI B.5 ANSI B.7 Series A MSS SP- ASME B.7 Series B API 605 BS EN 092/ (BS50) lbs lbs* lbs* Bar Weld Neck 50-2500 50-900 50-00 2.5-0 Weld Neck Rg Type Jot 00-2500 00-900 50-00 N/A Slip On 50-500 - - 2.5-0 Slip On Rg Type Jot 00-500 - - N/A Threaded 50-2500 - - 6-0 Lap Jot 50-2500 - - 6-0 Bld 50-2500 - - 2.5-0 Socket Weld 50-500 - - N/A Flanges Introduction Notes * Flange sizes 26 and above. What semi-fished product are flanges made from? Forgg A Plate ASTM A Bar Castg ANSI B.5 - - BS 29 - - - MSS SP- - - - API 605 - - - BS EN 092/(BS50) - BS 0 Notes - ASTM A plate can be used to manufacture ANSI B.5 bld flanges, but this is not generally accepted the UK. - Most small BS 0 flanges are normally made from bar as this is the most economical manufacturg process. 5-

Range/Sizes - Weld Neck Flanges - ANSI B.5 Flanges Range/Sizes - Weld Neck Flanges - ANSI B.5 Class 50 lb Nomal Pipe Size /2 / / /2 2 2 /2 /2 5 6 0 2 Pipe Flange Data Hub Data Outside 0.0 2.0.050 26.70.5.0.660 2..900.0 2.75 60.0 2.75 7.00.500.90.000 0.6.500. 5.56. 6.625..625 29. 0.75 27.0.75 2..00 55.6.00 06..00 57.2.00 50.0 2.00 609.6 Raised Face Drillg Data Weight A B C D E F G H I J Overall.500.90.0 9.60.250 0.0.6 7. 5.000 7.0 6.000 52. 7.000 77. 7.500 90.5.500 25.9 9.000 22.6 0.00 25.0.00 279..50 2.9.00 06. 9.00 2.6 2.00 5. 2.50 596.9 25.00 65.0 27.50 69.5 2.00. Inside 0..0.050 26.70.0 5.0.60 0.90 2.070 52.60 2.70 62.70.070 7.00.550 90..00 02. 5.050. 6.070 5.2 7.90 2.7 0.02 25.5.00 0. To be specified by Purchaser Flange Thickness m 0.0. 0.500.70 0.560. 0.690 7.50 22.0 0.90 2.90 0.90 2.90 0.90 2.90 0.90 2.90.000 25.0.0 2.0.90 0..75.0 5.0.0 6.60.560 9.60.690 2.90.0 7.0 Overall Length.0 7.0 2.060 52.0 2.90 55.60 2.250 57.5 2.0 62.00 2.500 6.50 2.750 69.5 2.750 69.5 2.0 7.0.000 76..500.90.500.90.000 0.6.000 0.6.500. 5.000 7.0 5.000 7.0 5.500 9.7 5.690.5 6.000 52. at Weld Bevel 0.0 2.0.050 26.70..50.660 2..900.0 2.0 60.5 2.0 7.5.500.90.000 0.6.500. 5.560.2 6.60..60 29.2 0.75 27.0.75 2..00 55.6.00 06..00 57.2.00 50.0 2.00 609.6 Hub.90 0..500.0.90 9.0 2.0 5.70 2.560 65.00.060 77.70.560 90.0.250 0.0.0 2.2 5.0.9 6.0.6 7.560 92.0 9.690 26..00 0.. 65. 5.75 00..00 75.2 9. 505.0 22.00 55. 26. 66. Face.0 5.00.690 2.90 2.000 50.0 2.500 6.50 2.0 7.5.6 9.90.0 0.6 5.000 7.0 5.500 9.7 6.90 57.2 7.0 5.7.500 25.9 0.62 269.7.75 2. 5.00.0.25.7.50 69.9 2.00 5. 2.00 5.2 27.25 692. Number of Holes Bolt Hole 22.0 22.0 22.0.000 25.0.000 25.0.0 2.0.0 2.0.75.75.0 5.0 of Circle of Holes 2.0 60.5 2.750 69.5.0 79.25.500.90.0 9.60.750 0.7 5.500 9.7 6.000 52. 7.000 77. 7.500 90.5.500 25.9 9.500 2..75 29.5.25 62.0 7.00..75 76. 2.25 59. 22.75 577.9 25.00 65.0 29.50 79. kg/ piece 0. 0.7.0..72 2.5..92 6.0 6..56 0.6 7.6 2.0 6.5. 60.6 6..5 5 Notes - Dimension B corresponds to the pipe side diameter. Values quoted assume 0S/Standard wall thickness. - Weights are based on manufacturer s data and are approximate. - Flat face flanges may be provided at full thickness, C, or with raised face removed (the latter is nonstandard). - For tolerances see page 5-. 5-

Range/Sizes - Weld Neck Flanges - ANSI B.5 Class 00 lb Nomal Pipe Size /2 / / /2 2 2 /2 /2 5 6 0 2 Pipe Flange Data Hub Data Outside 0.0 2.0.050 26.70.5.0.660 2..900.0 2.75 60.0 2.75 7.00.500.90.000 0.6.500. 5.56. 6.625..625 29. 0.75 27.0.75 2..00 55.6.00 06..00 57.2.00 50.0 2.00 609.6 Raised Face Drillg Data Weight A B C D E F G H I J Overall.750 95..6 7..0.9 5.250. 6.0 55. 6.500 5. 7.500 90.5.250 9.5 9.000 22.6 0.00 25.0.00 279..50 7.5 5.00.0 7.50.5.50 5.7 2.00 5.2 25.50 67.7 2.00 7.2 0.50 77.7 6.00 9. Inside 0..0.050 26.70.0 5.0.60 0.90 2.070 52.60 2.70 62.70.070 7.00.550 90..00 02. 5.050. 6.070 5.2 7.90 2.7 0.02 25.5.00 0. To be specified by Purchaser Flange Thickness m 0.560. 0.690 7.50 9.00 0.0.60 22.0.000 25.0.0 2.0.90 0..70.0 5.00.0 6.50.6.0.0 7.70 2.000 50.0 2.0 5.0 2.250 57.5 2.0 60.5 2.500 6.50 2.750 69.5 Overall Length 2.060 52.0 2.250 57.5 2.0 62.00 2.560 65.00 2.690 6.0 2.750 69.5.000 76..0 79.25.90.00.0 5.0.0 9.50.0 9.50.0.2.6 7. 5.0 0.0 5.6.7 5.750.0 6.250 5.7 6.0 2.0 6.6. at Weld Bevel 0.0 2.0.050 26.70..50.660 2..900.0 2.0 60.5 2.0 7.5.500.90.000 0.6.500. 5.560.2 6.60..60 29.2 0.75 27.0.75 2..00 55.6.00 06..00 57.2.00 50.0 2.00 609.6 Hub.500.0.0 7.70 2.0 5.0 2.500 6.50 2.750 69.5.0.00.90 00.0.6 7. 5.250. 5.750.0 7.000 77..0 6.2 0.25 260..62.5.75 7.6.75 25. 9.00 2.6 2.00 5. 2. 57.2 27.62 70.5 Face.0 5.00.690 2.90 2.000 50.0 2.500 6.50 2.0 7.5.6 9.90.0 0.6 5.000 7.0 5.500 9.7 6.90 57.2 7.0 5.7.500 25.9 0.62 269.7.75 2. 5.00.0.25.7.50 69.9 2.00 5. 2.00 5.2 27.25 692. Number of Holes 2 2 2 Bolt Hole 9.00 9.00 9.00 22.0 9.00 22.0 22.0 22.0 22.0 22.0 22.0.000 25.0.0 2.0.70.70.0 5.00.0 5.00.0 5.00.6.0 of Circle of Holes 2.6 66.55.250 2.50.500.90.0 9.50.500. 5.000 7.0 5.0 9. 6.6. 7.250. 7.0 0. 9.250 2.9 0.62 269.7.00 0.2 5.25 7. 7.75 50..25 5. 22.50 57.5 2.75 62.6 27.00 65. 2.00. kg/ piece 0.75.26.52 2.0 2.9.0 5.7 6.9.67.2 5. 9. 29.9 2.7 6. 5. 06 5 Flanges Range/Sizes - Weld Neck Flanges - ANSI B.5 Notes - Dimension B corresponds to the pipe side diameter. Values quoted assume 0S/Standard wall thickness. - Weights are based on manufacturer s data and are approximate. - Flat face flanges may be provided at full thickness, C, or with raised face removed (the latter is nonstandard). - For tolerances see page 5-. 5-5

Range/Sizes - Slip On Flanges - ANSI B.5 Flanges Range/Sizes - Slip On Flanges - ANSI B.5 Class 50 lb Nomal Pipe Size /2 / / /2 2 2 /2 /2 5 6 0 2 Pipe Flange Data Hub Outside 0.0 2.0.050 26.70.5.0.660 2..900.0 2.75 60.0 2.75 7.00.500.90.000 0.6.500. 5.56. 6.625..625 29. 0.75 27.0.75 2..00 55.6.00 06..00 57.2.00 50.0 2.00 609.6 Raised Face Drillg Data Weight A B C D F G H I J Overall.500.90.0 9.60.250 0.0.6 7. 5.000 7.0 6.000 52. 7.000 77. 7.500 90.5.500 25.9 9.000 22.6 0.00 25.0.00 279..50 2.9.00 06. 9.00 2.6 2.00 5. 2.50 596.9 25.00 65.0 27.50 69.5 2.00. Inside 22.0.090 27.70.60.50.700..950 9.50 2.0 62.00 2.90 7.70.570 90.70.070 0..570. 5.660. 6.7 70.7.7 22.5 0. 276.. 27.. 59.. 0.5. 6.. 5. 2.25 6.0 Flange Thickness m 0.0. 0.500.70 0.560. 0.690 7.50 22.0 0.90 2.90 0.90 2.90 0.90 2.90 0.90 2.90.000 25.0.0 2.0.90 0..75.0 5.0.0 6.60.560 9.60.690 2.90.0 7.0 Overall Length 0.690 7.50 0.0.60 22.0.000 25.0.0 2.0.90 0..75.0.0.0 6.60.560 9.60.750.50.90 9.0 2.90 55.60 2.250 57.5 2.500 6.50 2.690 6.0 2.0 7.5.250 2.60 Hub.90 0..500.0.90 9.0 2.0 5.70 2.560 65.00.060 77.70.560 90.0.250 0.0.0 2.2 5.0.9 6.0.6 7.560 92.0 9.690 26..00 0.. 65. 5.75 00..00 57.2 9. 505.0 22.00 55. 26. 66. Face.0 5.0.690 2.90 2.000 50.0 2.500 6.50 2.0 7.5.6 9.90.0 0.6 5.000 7.0 5.500 9.7 6.90 57.2 7.0 5.7.500 25.9 0.62 269.7.75 2.9 5.00.0.25..50 69.9 2.00 5. 2.00 5.2 27.25 692.2 Number of Holes Bolt Hole 22.0 22.0 22.0.000 25.0.000 25.0.0 2.0.0 2.0.75.75.0 5.0 of Circle of Holes 2.0 60.5 2.750 69.5.0 79.25.500.90.0 9.60.750 0.7 5.500 9.7 6.000 52. 7.000 77. 7.500 90.5.500 25.9 9.500 2..75 29.5.25 62.0 7.00..75 76. 2.25 59. 22.75 577.9 25.00 65.0 29.50 79. kg/ piece 0.9 0.56 0.7.0.2 2.06.2.5. 5.0 6.07 7.5..5 26.2.6..9 6.9 6.9 Notes - Weights are based on manufacturer s data and are approximate. - Flat face flanges may be provided at full thickness, C, or with raised face removed (the latter is nonstandard). - For tolerances see page 5-. 5-6

Range/Sizes - Slip On Flanges - ANSI B.5 Class 00 lb Nomal Pipe Size /2 / / /2 2 2 /2 /2 5 6 0 2 Pipe Flange Data Hub Outside 0.0 2.0.050 26.70.5.0.660 2..900.0 2.75 60.0 2.75 7.00.500.90.000 0.6.500. 5.56. 6.625..625 29. 0.75 27.0.75 2..00 55.6.00 06..00 57.2.00 50.0 2.00 609.6 Raised Face Drillg Data Weight A B C D F G H I J Overall.750 95..6 7..0.9 5.250. 6.0 55. 6.500 5. 7.500 90.5.250 9.5 9.000 22.6 0.00 25.0.00 279..50 7.5 5.00.0 7.50.5.50 5.7 2.00 5.2 25.50 67.7 2.00 7.2 0.50 77.7 6.00 9. Inside 22.0.090 27.70.60.50.700..950 9.50 2.0 62.00 2.90 7.70.570 90.70.070 0..570. 5.660. 6.7 70.7.7 22.5 0. 276.. 27.. 59.. 0.5. 6.. 5. 2.25 6.0 Flange Thickness m 0.560. 0.690 7.50 9.00 0.0.60 22.0.000 25.0.0 2.0.90 0..70.0 5.00.0 6.50.6.0.0 7.70 2.000 50.0 2.0 5.0 2.250 57.5 2.0 60.5 2.500 6.50 2.750 69.5 Overall Length 22.0.000 25.0.060 26.90.060 26.90.90 0..0..500.0.690 2.90.750.0.0 7.70 2.000 50.0 2.060 52.0 2.0 6.90 2.6 66.55 2.0 7.5.000 76..250 2.50.500.90.750 95..90 06. Hub.500.0.0 7.70 2.0 5.0 2.500 6.50 2.750 69.5.0.00.90 00.0.6 7. 5.250. 5.750.0 7.000 77..0 6.2 0.25 260..62.5.75 7.6.75 25. 9.00 2.6 2.00 5. 2. 57.2 27.62 70.5 Face.0 5.0.690 2.90 2.000 50.0 2.500 6.50 2.0 7.5.6 9.90.0 0.6 5.000 7.0 5.500 9.7 6.90 57.2 7.0 5.7.500 25.9 0.62 269.7.75 2.9 5.00.0.25..50 69.9 2.00 5. 2.00 5.2 27.25 692.2 Number of Holes 2 2 2 Bolt Hole 22.0 22.0 22.0 22.0 22.0 22.0 22.0.000 25.0.0 2.0.70.70.0 5.00.0 5.00.0 5.00.6.00 of Circle of Holes 2.6 66.55.250 2.50.500.90.0 9.60.500. 5.000 7.0 5.0 9. 6.6. 7.250.2 7.0 0. 9.250 2.9 0.62 269.7.00 0.2 5.25 7. 7.75 50..25 5. 22.50 57.5 2.75 62.7 27.00 65. 2.00. kg/ piece 0.6..6.6 2.9 2.7.2 5.5 7. 9.6. 5.6 2.2. 9. 69.9. 09 Flanges Range/Sizes - Slip On Flanges - ANSI B.5 Notes - Weights are based on manufacturer s data and are approximate. - Flat face flanges may be provided at full thickness, C, or with raised face removed (the latter is nonstandard). - For tolerances see page 5-. 5-7

Range/Sizes - Bld Flanges - ANSI B.5 Flanges Range/Sizes - Bld Flanges - ANSI B.5 Class 50 lb Nomal Pipe Size /2 / / /2 2 2 /2 /2 5 6 0 2 Pipe Flange Data Raised Face Drillg Data Weight Outside 0.0 2.0.050 26.70.5.0.660 2..900.0 2.75 60.0 2.75 7.00.500.90.000 0.6.500. 5.56. 6.625..625 29. 0.75 27.0.75 2..00 55.6.00 06..00 57.2.00 50.0 2.00 609.6 A C G H I J Overall.500.90.0 9.60.250 0.0.6 7. 5.000 7.0 6.000 52. 7.000 77. 7.500 90.5.500 25.9 9.000 22.6 0.00 25.0.00 279..50 2.9.00 06. 9.00 2.6 2.00 5. 2.50 596.9 25.00 65.0 27.50 69.5 2.00. Flange Thickness m 0.0. 0.500.70 0.560. 0.690 7.50 22.0 0.90 2.90 0.90 2.90 0.90 2.90 0.90 2.90.000 25.0.0 2.0.90 0..75.0 5.0.0 6.60.560 9.60.690 2.90.0 7.0 Face.0 5.0.690 2.90 2.000 50.0 2.500 6.50 2.0 7.5.6 9.90.0 0.6 5.000 7.0 5.500 9.7 6.90 57.2 7.0 5.7.500 25.9 0.62 269.7.75 2.9 5.00.0.25..50 69.9 2.00 5. 2.00 5.2 27.25 692.2 Number of Holes Bolt Hole 22.0 22.0 22.0.000 25.0.000 25.0.0 2.0.0 2.0.75.75.0 5.0 of Circle of Holes 2.0 60.5 2.750 69.5.0 79.25.500.90.0 9.60.750 0.7 5.500 9.7 6.000 52. 7.000 77. 7.500 90.5.500 25.9 9.500 2..75 29.5.25 62.0 7.00..75 76. 2.25 59. 22.75 577.9 25.00 65.0 29.50 79. kg/ piece 0.2 0.6 0.6.7.5 2.2.9.9 6.7 7.00.6. 9.6 2..2 5. 76.0 9.7 2 5 Notes - Weights are based on manufacturer s data and are approximate. - Flat face flanges may be provided at full thickness, C, or with raised face removed (the latter is nonstandard). - For tolerances see page 5-. 5-

Range/Sizes - Bld Flanges - ANSI B.5 Class 00 lb Nomal Pipe Size /2 / / /2 2 2 /2 /2 5 6 0 2 Pipe Flange Data Raised Face Drillg Data Weight Outside 0.0 2.0.050 26.70.5.0.660 2..900.0 2.75 60.0 2.75 7.00.500.90.000 0.6.500. 5.56. 6.625..625 29. 0.75 27.0.75 2..00 55.6.00 06..00 57.2.00 50.0 2.00 609.6 A C G H I J Overall.750 95..6 7..0.9 5.250. 6.0 55. 6.500 5. 7.500 90.5.250 9.5 9.000 22.6 0.00 25.0.00 279..50 7.5 5.00.0 7.50.5.50 5.7 2.00 5.2 25.50 67.7 2.00 7.2 0.50 77.7 6.00 9. Flange Thickness m 0.560. 0.690 7.50 9.00 0.0.60 22.0.000 25.0.0 2.0.90 0..70.0 5.00.0 6.50.6.0.0 7.70 2.000 50.0 2.0 5.0 2.250 57.5 2.0 60.5 2.500 6.50 2.750 69.5 Face.0 5.0.690 2.90 2.000 50.0 2.500 6.50 2.0 7.5.6 9.90.0 0.6 5.000 7.0 5.500 9.7 6.90 57.2 7.0 5.7.500 25.9 0.62 269.7.75 2.9 5.00.0.25..50 69.9 2.00 5. 2.00 5.2 27.25 692.2 Number of Holes 2 2 2 Bolt Hole 9.00 9.00 9.00 22. 22.0 22.0 22.0 22.0 22.0 22.0.000 25.0.0 2.0.70.70.0 5.00.0 5.00.0 5.00.6.0 of Circle of Holes 2.6 66.55.250 2.50.500.90.0 9.50.500. 5.000 7.0 5.0.9 6.6. 7.250. 7.00 0. 9.250 2.9 0.62 269.7.00 0.2 5.25 7. 7.75 50..25 5. 22.50 57.5 2.75 62.6 27.00 65. 2.00. kg/ piece 0.6..9.79 2.66..5 6..7.5 5.6.9. 5. 7. 05 7 75 22 9 Flanges Range/Sizes - Bld Flanges - ANSI B.5 Notes - Weights are based on manufacturer s data and are approximate. - Flat face flanges may be provided at full thickness, C, or with raised face removed (the latter is nonstandard). - For tolerances see page 5-. 5-9

Specifications - ASTM A/AM Flanges Specifications - ASTM A/AM Forged or rolled alloy steel pipe flanges, forged fittgs, and valves and parts for high temperature service This specification covers forged low alloy and staless steel pipg components for use pressure systems. These clude flanges, fittgs, valves and similar parts manufactured to dimensional standards such as ASME/ANSI. Products made to this specification are limited to a maximum weight of 0,000 lb (,50 kg). Note - Although low allow steels are covered by this standard, only staless steels (martensitic, ferritic, austenitic and duplex) are cluded this suary. Dimensions and tolerances Dimensions and tolerances. ASME/ANSI specifications B.5 and B. are referenced. Flange dimensions and tolerances (see page 5-). Manufacture Materials. Refer to chemical composition table (staless steel grades only shown). Elements not specified the table are not permitted, specifically selenium or other elements added for free-machg properties. The steel may be melted by electric-furnace, or vacuum-furnace, or by either of these followed by vacuum or electroslag-consumable remeltg. Vacuum meltg or remeltg is not suitable for grades contag or modified by nitrogen. Grade F XM-27Cb may be electron-beam melted. Manufacture. The steel is forged or rolled as near as possible to size and shape of the product. Small cyldrical parts (excludg flanges) may be mached directly from forged or rolled bar without additional hot workg (limits defed ASTM A2 apply for martensitic steels, A0 for austenitic steels and A5 for duplex steels). Elbows, returns and tees are not mached directly from bar. Heat treatment. Refer to heat treatment table. Heat treatment of forggs may be performed before machg. For martensitic and ferritic grades, liquid quench followed by temperg is permitted, subject to purchaser agreement. Small cyldrical parts (excludg flanges) mached directly from forged or rolled austenitic steel may be furnished annealed to this specification with subsequent light cold drawg or straighteng permitted. Markg. Each forgg is marked with manufacturers name, heat number (or heat identification), designation of service ratg, specification number, grade (e.g. F0) and size. Additionally: QT = Liquid quenched and tempered W = Welded WNS = Not post repair weld heat treated. Fish and repair Appearance. Forggs have a workmanlike fish and shall be free of scale, machg burns and jurous, imperfections (i.e. those that encroach on mimum wall thickness). Defect repair by grdg or machg. The followg may be removed: Surface discontuity as above. Mechanical marks, abrasions or pits deeper than / (.6). Defect repair by weldg: Permitted unless purchaser prohibits. Defect removal by chippg or grdg is verified by magnetic particle spection. Repair is limited to 0% of surface area and /% of nomal wall thickness. Repair weldg electrodes and post weld repair heat treatments are defed A but are not detailed this suary. 5-0

Specifications - ASTM A/AM Tensile and hardness requirements Grade UNS Martensitic Staless Steels: Tensile Strength m Yield Strength m Elongation 2 (50 ) or D, m Reduction of area, m ksi MPa ksi MPa % % Brell Hardness HB F6a Class S000 70 5 0 275 5-7 F6a Class 2 S000 5 55 55 0 5 7-229 F6a Class S000 0 760 5 55 5 5 25-02 F6a Class S000 0 95 0 760 5 26-2 F6b S026 0-5 760-90 90 6 5 25-25 F6NM S500 5 790 90 6 5 5 295 max Ferritic Staless Steels: FXM-27Cb S627 60 5 5 5 90 max F29 S2900 60 5 5 5 90 max F0 S000 60 5 5 5 90 max Austenitic Staless Steels: All All 75 2 55 2 0 5 0 50 - F0L S00 70 5 25 70 0 50 - F0N S05 0 550 5 0 50 5 - FL S0 70 5 25 70 0 50 - FN S5 0 550 5 0 50 5 - F7L S70 70 5 25 70 0 50 - FXM- S290 90 6 50 5 5 60 - FXM-9 S90 00 690 55 0 5 55 - F0 S00 0 550 0 5 0 50 - F S5 9 650 00 5 50 - F5 S05 7 600 5 0 0 50 - F6 S0600 7 50 5 0 50 - F7 S725 75 525 0 5 0 50 - F S726 0 550 5 0 50 - F9 S565 5 795 60 5 5 0 - F56 S22 7 500 27 5 0 5 - Duplex Staless Steels F50 S00 00-0 690-95 65 50 25 50 - F5 S0 90 6 65 50 25 5 - F52 S2950 00 690 70 5 5 - - F5 S2750 6 00 6 0 6 550 6 5-0 max F5 S270 00 0 550 5 0 0 max F55 S2760 09-0 750-95 0 550 25 5 - F57 S9277 5 55 25 50 - Flanges Specifications - ASTM A/AM Notes Determed by the 0.2% offset method. For ferritic steels only, the 0.5% extension-under-load method may also be used. 2 For sections over 5. [0] thickness, the mimum tensile strength shall be 70 ksi [5 MPa]. For sections over 5. [0] thickness, the mimum tensile strength shall be 65 ksi [50 MPa]. Longitudal. The transverse elongation shall be 25% 2. or 50, m. 5 Longitudal. The transverse reduction of area shall be 5% m. 6 For sections over 2. [50] thickness, the mimum tensile strength shall be 09 ksi [750 MPa]; the mimum yield strength shall be 75 ksi [55 MPa]. - All = All austenitic grades as listed the chemical composition table except as identified this table. 5-

Specifications - ASME/ANSI B.5 Flanges Specifications - ASME/ANSI B.5 American national standards ASME/ANSI B.5 and B.7 together cover pipe flanges up to NPS 60 (NPS is the largest detailed this suary). ASME/ANSI B.7 covers two series of flanges, Series A which is equivalent to MSS SP- (the 996 Edition of MSS SP- complies with B.7 tolerances), and Series B which is equivalent to API 605 (API 605 is now cancelled). Dimensions and tolerances Tolerances on flange dimensions (ASME/ANSI B.5) Dimension Range General and Bld Flanges (For bld flange dimensions see pages 5-/9): G (raised face diameter) Tolerance < NPS 2 ±0.0 ±0.76 > NPS 26, with 0.06 raised face > NPS 26, with 0.25 raised face ±0.0 ±2.0 ±0.0 ±.02 I (bolt hole diameter) All No tolerance B.5 or B.7 J (bolt circle diameter) All ±0.06 ±.52 Centre to centre of adjacent bolt holes Eccenticity of bolt circle and mached facg diameters All ±0.0 ±0.76 < NPS 2 /2 ±0.0 ±0.76 > NPS ±0.06 ±.52 Weld Neck Flanges (For dimensions see pages 5-/5): D (overall length) < NPS +0.06 +.52 NPS 5 to 0 +0.06, -0. +.52, -.05 NPS to 2 +0., -0. +.05, -.57 > NPS 26 ±0.9 ±. Thickness of hub All > 7.5% of pipe nomal wall thickness Slip on (see page 5-6/7), Lap Jot and Socket Weldg Flanges: B (side diameter, or bore) < NPS 0 +0.0, -0.0 +0.76, -0.0 > NPS +0.06, -0.0 +.52, -0.0 Threaded Flanges: B (counterbore) (Not applicable for Class 50 lb) < NPS 0 +0.0, -0.0 +0.76, -0.0 > NPS +0.06, -0.0 +.52, -0.0 5-

Range/Sizes - EN 092 / (BS50) BS50 is now obsolete and has been replaced by EN 092. However the dimensions and tolerances have not changed. Flange types and methods of manufacture ISO EN BS 0 0 Type of Flange and Collar Plate flange for weldg Forged a Cast Made from flat products (plates) Mached from rolled or forged bars and forged sectional steel Bent and electric welded from bars, sectional steel or strip b,c,d,e yes no yes yes yes 05 05 Bld flange yes no yes yes no Weld-neck flange yes no no yes Hubbed slip-on flange for weldg yes, for > DN 700 yes no no yes no a Seamless rolled, pressed, forged. b Only one radial weld is allowed under DN 00. c Welded flanges allowed only for an application up to 70ºC conformance with EN 0-:02, D... d In case flanges are made by cold formg of a base material e.g. flat product, some mechanical properties, like elongation after fracture (A) and impact energy (KV), will be impaired due to cold formg without subsequent heat treatment. Flanges Range/Sizes - EN 092 / (BS50) Repairs by weldg With the exception of weld repairs carried out accordg to BSEN 092-:07 (E) clause 5., repairs by weldg are permitted only by written agreement of the purchaser. With the certificate for material or component relevant documents shall be noted, that approved weldg procedure and welders qualification have been applied. Boltg Flanges shall be suitable for use with the number and size of boltg as specified the Tables on pages 5- to 5-. The boltg shall be chosen by the equipment manufacturer accordg to the pressure, temperature, flange material and gasket so that the flanged jot remas tight under the expected operatg conditions. For selection of boltg, see EN 55-, for combation of the materials of flanges and boltg see EN 55-2, for formation. Gaskets The various gasket types, dimensions, design characteristics and materials used are not with the scope of this European Standard, Dimensions of gaskets are given the series of standards EN 5. 5-

Range/Sizes - EN 092 / (BS50) Flanges Range/Sizes - EN 092 / (BS50) Flange drillg details DN PN A B C Bolt holes No. Size 0 0 & 90 60 M 5 0 & 95 65 M 0 & 05 75 M 25 0 & 5 5 M 2 0 & 0 00 M 0 0 & 50 0 M 50 0 & 5 5 M 65 0 & 5 5 / M 0 0 & 0 0 M 00 0 & 2 0 M 5 0 & 250 20 M 50 0 & 25 22 M 0 0 & 0 295 22 / M 250 0 95 50 22 M 05 55 26 M2 00 0 5 00 22 M 60 0 26 M2 50 0 505 60 22 M 5 70 26 M2 00 0 565 55 26 M2 50 525 0 M27 50 0 65 565 26 M2 60 55 0 M27 DN PN A B C Bolt holes No. Size 500 0 670 6 26 M2 75 650 M0 600 0 70 725 0 M27 0 770 6 M 700 0 95 0 0 2 M27 90 0 6 2 M 00 0 05 950 2 M0 025 950 9 2 M6 900 0 5 050 2 M0 5 050 9 2 M6 000 0 0 0 6 2 M 55 70 2 2 M9 00 0 55 0 9 2 M6 5 90 2 M5 00 0 75 590 2 6 M9 5 590 6 M5 00 0 95 0 0 M5 90 0 56 0 M52 00 0 25 M5 20 56 M52 00 0 225 2 M5 25 2 62 M56 5-

Range/Sizes - Plate Flanges Code 0 (0) - EN 092 / (BS50) DN PN A B C 0 0 & 90.0 5 0 & 95 22.0 0 & 05 27.5 25 0 & 5.5 2 0 & 0.5 0 0 & 50 9.5 50 0 & 5 6.5 65 0 & 5 77.5 0 0 & 0 90.5 00 0 & 2 22.0 5 0 & 250 22.5 50 0 & 25 2 70.5 0 0 & 0 2 22.5 250 0 95 26 05 29 276.5 Notes - Dimension B is the flange thickness with or without a raised face. - For drillg details see page 5-. - For tolerances see page 5-9. - For facg types and dimensions see page 5- and 5-2. DN PN A B C 00 50 00 50 500 600 0 5 26 60 2 27.5 0 505 2 59.5 5 5 59.0 0 565 2 50 0 65 6 60 2 0 670 75 6 0 70 2 0 52.0 62.0 5.5 6.5 Flanges Range/Sizes - Plate Flanges Code 0 (0) - EN 092 / (BS50) 5-5

Range/Sizes - Weld Neck Flanges Code () - EN 092 / (BS50) Flanges Range/Sizes - Weld Neck Flanges Code () - EN 092 / (BS50) DN PN A B C D E F G H 0 5 25 2 0 50 65 0 00 5 50 0 250 00 0 90 5 2. 7.2 6 90 5 2. 0 95 5 2 2 2. 6 95 5 2 2 0 05 9 2. 26.9 6 05 9 2. 0 5 6 2.6.7 6 5 6 2.6 0 0 0 56 2.6 2. 6 5 0 0 56 2.6 0 50 2 6 2.6. 7 5 50 2 6 2.6 0 5 5 7 2.9 60. 5 5 5 7 2.9 0 5 5 92 2.9 76. 0 6 5 5 92 2.9 0 0 50 0.2.9 0 6 0 50 0.2 0 2 52 0.6. 6 2 52 0.6 0 250 22 55 5 9.7 6 250 22 55 5 0 25 22 55.5. 25 22 55.5 0 0 2 62 2 5.6 29. 0 2 62 2 5.6 0 95 26 6 2 6. 27 0 05 26 70 2 6. 0 5 26 6 2 7. 2.9 0 60 2 7 2 7. Notes - For drillg details see page 5-. - For tolerances see page 5-9. - For facg types and dimensions see pages 5- and 5-2. DN PN A B C D E F G H 50 00 50 500 600 700 00 900 0 505 26 6 90 7. 55.6 0 5 0 2 90 0 565 26 72 0 7. 06. 0 50 2 5 0 65 2 72 7. 57 60 7 90 0 670 2 75 50 7. 50 75 90 56 0 70 2 0 60 7. 60 0 6 95 650. 0 95 0 0 76 7 90 6 00 750. 0 05 2 90 025 05 0 0 5 95 9 0 9 5 0 0 9 0 000 0 0 0 95 050 0 55 2 0 22 056 0 00 0 55 5 25 56 5 0 0 60.5 00 0 75 0 2 0 25 0 5 52 5 0 5.2 00 0 95 6 0 25 66 90 5 0 5 6 00 0 25 0 50 0 0 6 5 5 20 62 70 5 70 7.5 00 0 225 5 50 0 70 5 25 66 90 0 72 5-

Range/Sizes - Slip On Flanges Code () - EN 092 / (BS50) DN PN A B C D E F 0 0 & 90.0 0 5 0 & 95 22 5 0 & 05 27.5 2 5 25 0 & 5.5 2 52 2 0 & 0.5 26 60 5 0 0 & 50 9.5 26 70 5 50 0 & 5 6.5 2 5 65 0 & 5 77.5 2 0 6 0 0 & 0 90.5 6 00 0 & 2.0 0 0 6 5 0 & 250.5 22 6 50 0 & 25 70.5 22 95 0 0 & 0 22.5 2 26 250 0 95 276.5 26 6 29 05 26 6 29 Notes - The hubs of slip on (Code ) flanges are parallel or have a draft <7 degrees. - For drillg details see page 5-. - For tolerances see page 5-9. - For facg types and dimensions see pages 5- and 5-2. 0 DN PN A B C D E F 00 50 00 50 500 600 0 5 27.5 26 6 50 60 2 6 50 0 505 59.5 26 5 00 5 59.0 0 57 00 0 565.0 26 57 56 50 2 6 56 0 65 62.0 2 6 502 60 6 502 0 670 5.5 2 67 559 75 7 559 0 70 6.5 2 75 65 0 6 65 0 0 0 Flanges Range/Sizes - Slip On Flanges Code () - EN 092 / (BS50) 5-7

Range/Sizes - Blank/Bld Flanges Code 05 (05) - EN 092 / (BS50) Flanges Range/Sizes - Bld/Blank Flanges Code 05 (05) - EN 092 / (BS50) DN PN A B C 0 0 & 90-5 0 & 95-0 & 05-25 0 & 5-2 0 & 0-0 0 & 50-50 0 & 5-65 0 & 5 55 0 0 & 0 70 00 0 & 2 90 5 0 & 250 22 5 50 0 & 25 22 0 0 0 & 0 2 90 250 00 50 0 95 26 25 05 26 25 0 5 26 25 60 2 25 0 505 26 25 5 0 25 DN PN A B C 00 50 500 600 700 00 900 000 00 0 565 26 75 50 2 75 0 65 2 25 60 25 0 670 2 75 75 6 75 0 70 575 0 575 0 95 670 90 670 0 05 2 770 025 52 770 0 5 6 60 5 5 60 0 0 52 960 55 6 960 0 55 60 0 5 76 0 Notes - Dimension B is the range thickness with or without a raised face. - Dimension C is the maximum diameter of the centre portion of a blank flange face which need not be mached. - For drillg details see page 5-. - For tolerances see page 5-9. - For facg types and dimensions see pages 5- and 5-2. 5-

Specifications - EN 092 (BS50) Dimensions and tolerances Flange Facgs (see page 5- and 5-2) Surface Fish Flange Drillg Details (see page 5-) All Weld Neck Flanges, Code (see page 5-) Slip on, Code (see page 5-7) and Threaded, Code Flanges Blank Flanges, Code 05 (see page 5-) Dimension Range Tolerance Eccentricity of mached facg diameters < DN 00.0 > DN 00 2.0 2 +0, -.0 +0, -2.0 a (type B facg height) +0, -.0 5 +0, -.0 6 +0, -5.0 b (type C and E facg height) All +0.5, -0 b (type G facg height) All +0, -0.5 b (type H facg height, outer) All +0.2, -0 c (type D and F facg height) All +0, -0.5 d (type H facg height, ner) All +0.5, -0 B and E (facg diameters) All +0, -0.5 C and D (facg diameters) All +0.5, -0 Facg types A, B, E and F All, turng Ra =.2 µm m,.5 µm max All, other than turng Ra =.2 µm m, 6. µm max Facg types C, D, G and H All Ra = 0. µm m,.2 µm max B (diameter of bolt circle) Bolt sizes M0 to M2 ±0.9 Bolt sizes M27 to M5 ±. Centre to centre of adjacent bolt holes Bolt sizes M0 to M2 ±0.5 Bolt sizes M27 to M5 ±0.7 < DN 50 ±2.0 > DN 50 < DN 500 ±.0 A (outside diameter) > DN 500 < DN 00 ±5.0 > DN 00 < DN 00 ±7.0 > DN 00 ±0.0 < thickness ±.0 C (flange thickness, > < mached on both faces) 50 thickness ±.0 > 50 thickness ±.0 C (flange thickness, mached on front face) B (outside diameter of hub at weldg end) F (hub diameter) D (length through hub) E (slip on flange hub diameter) B (threaded flange hub diameter) B (slip on bore diameter) D (length through hub) B (flange thickness) C (unmached centre portion) < thickness +2.0, -.0 > < 50 thickness +.0, -.5 > 50 thickness +7.0, -2.0 < DN 5 +.0, -0 > DN 5 < DN 00 +.5, -0 > DN 00 +6.0, -0 < DN 50 +0, -2.0 > DN 50 < DN 50 +0, -.0 > DN 50 < DN 00 +0, -6.0 > DN 00 < DN 600 +0, -.0 > DN 600 < DN 00 +0, -0.0 < DN 0 ±.5 > DN 0 < DN 250 ±2.0 > DN 250 ±.0 < DN 50 +.0, -0 > DN 50 < DN 50 +2.0, -0 > DN 50 < DN 00 +.0, -.0 > DN 00 < DN 600 +.0, -0 > DN 600 < DN 00 +.0, -0 > DN 00 < DN 00 +.0, -0 > DN 00 +.0, -0 < DN 00 +0.5, -0 > DN 00 < DN 00 +.0, -0 > DN 00 < DN 600 +.5, -0 > DN 600 +.0, -0 Same as Weld Neck D Same as C for all other flanges Maximum specified Flanges Specifications - EN 092 (BS50) 5-9

Specifications - EN 092 (BS50) Flanges Specifications - EN 092 (BS50) Flange facgs EN 092 (BS50) flange facg types A to H are defed below. The dimensions vary with pipe size (DN) and pressure ratg (PN) as detailed the table on page 5-2. 5-

Specifications - EN 092 (BS50) Flange facg dimensions DN PN 0 PN Face Dimensions A B C D E 0 0 0 5 2 2 2 2-5 5 5 5 9 0 29 2 2 2-5 5 5 50 5 6 5 2 2 5 25 6 6 57 5 2 2 2 5 2 7 7 65 66 5 50 2 2 5 0 75 76 6 60 2 5 50 02 02 7 7 72 2 5 65 2 2 09 0 95 9 2 5 0 0 06 05 2 5 00 5 5 9 50 9.5.5 2.5 2 5 6 5 75 76 55 5.5.5 2.5 2 5 6 50 2 2.5.5 2.5 2 5 6 0 26 26 259 260 29 2.5.5 2.5 2 5 6 250 292 29.5.5 2.5 2 5 6 00 70 7 6 6 2.5.5 2.5 2 5 6 50 0 2 22 95 9 5 27 2 7 00 2 90 7 7 7 6 5 27 2 7 50 52 550 52 52 97 96 5 27 2 7 500 55 60 575 576 59 5 5 27 2 7 600 65 725 675 676 69 6 5 5 27 2 7 700 00 795 777 77 75 750 5 5 27 2 7 00 905 900 2 56 55 5 5 27 2 7 900 005 000 97 9 96 960 5 5 27 2 7 000 0 5 092 09 062 060 5 6 5 2 9 00 0 0 92 9 62 60 5 6 5 2 9 00 55 50 92 9 2 0 5 6 5 2 9 00 760 750 92 9 62 60 5 6 5 2 9 00 960 950 92 9 2 0 5 6 5 2 9 00 270 250 92 9 62 60 5 6 5 2 9 Flanges Specifications - EN 092 (BS50) 5-2

Range/Sizes/Specifications - EN 092 (BS50) Flanges Range/Sizes/Specifications - EN 092 (BS50) Masses of flanges PN DN Type 0 Type 05 Type Type kg kg kg kg 0 0.60 0.722 0.67 0.66 5 0.670 0. 0.76 0.722 0.96..09.0 25...0.25 2.2 2.0.9. 0 2.0 2.5 2.5 2.06 50 2.7 2. 2.5 2.9 65..5.0 2.97 0.60.6.92.7 00.9 5.65.62. 5 5.. 6.0 6.07 50 7. 0.5 7. 7.2 0 9.7.2.5 9.0 250.2 25.0.7.6 00 9.0 5. 22. 7.2 50 2.2.0 2. 27.9 00 5.9 6.5. 5.7 50 6. 96.6 50.6 5.0 500 6.0 66.2 60. 600 02 226 96.5 9.0 700-25 0-00 - 2-900 - 55-000 - 60 2-00 - - 90-00 - - 95-00 - - 760-00 - - 929-00 - - 5 - With bolt holes. 5-22

Range/Sizes/Specifications - BS0 Plate Flanges British Standard BS 0 : 962 - Specification for Flanges and Boltg for Pipes, Valves, and Fittgs. This covers pla, boss, tegrally cast or forged, and weldg neck type flanges, ten tables. Although BS 0 is obsolescent, it remas use for the dimensions of light duty, economy staless steel flanges applications where corrosion resistance and/or hygiene, rather than high pressures and temperatures, are the primary considerations. The followg tables detail the applicable standard dimensions from Tables D, E, F and H of BS 0. Flange dimensions based on tables D and E of BS 0 : 962 Coon BS 0 Table D Dimensions BS 0 Table E Dimensions Flange Size Designation (Nomal Bore of Pipe) Overall of Flange Flange Thickness Bolt Circle Number of Bolts of Bolts Overall of Flange Flange Thickness Bolt Circle Number of Bolts /2 / / 2 5 / /2 / of Bolts / 2 5 / /2 / / 2 7 / /2 / 2 7 / /2 /2 / / /2 5 / / / /2 /2 / 7 / /2 / / 7 / /2 5 / 9 /2 / /2 5 / 7 / /2 /2 7 / /2 2 6 5 / /2 5 / 6 / /2 5 / 2 /2 6 /2 7 / 5 / 5 5 / 6 /2 / 5 / 5 / 7 / /2 5 5 / 7 / 5 / 5 / /2 / 6 /2 5 / 5 /2 6 /2 5 / /2 / 7 5 / /2 /2 7 5 / Flanges Range/Sizes/Specifications - BS 0 Plate Flanges 5 0 /2 / 5 / 0 9 / / 5 / 6 /2 9 / 5 / / 9 / / 7 /2 0 / 5 / / 0 / / / /2 /2 5 / / / /2 / 9 /2 5 / / 5 / /2 / / / 0 5 / / 7 / / / / 7 / 9 / / 5 2 / 22 / / 7 / / 9 / 7 / 7 / 7 / /2 7 / / / /2 7 / 7 / 9 /2 7 / 2 / / 9 /2 7 / 7 / /2 7 / 22 / / /2 7 / 7 2 2 / 7 / 2 / 2 / 7 / 25 / 2 7 / 25 / / 2 7 / 9 26 /2 2 7 / 26 /2 /2 2 7 / 27 / / 25 / 7 / 27 / /2 25 / 7 / 2 29 / 26 /2 7 / 29 5 / 26 /2 22 0 / 27 /2 0 / 27 /2 2 / 2 /2 / 2 /2 2 2 /2 / 29 / 2 /2 7 / 29 / / Notes - Bolt hole diameters are as follows: For /2 and 5 / bolts, the bolt hole shall be / larger than the bolt diameter. For / bolts and larger, the bolt hole shall be not more than / larger than the bolt diameter. 5-2

r www.aalco.co.uk ABERDEEN Tel 02 50 Fax 02 792 e-mail aberdeen@aalco.co.uk AYLESBURY Tel 096 6700 Fax 096 992 e-mail aylesbury@aalco.co.uk BELFAST Tel 0290 Fax 0290 7 7 e-mail belfast@aalco.co.uk BIRMINGHAM Tel 0 55 600 Fax 0 55 66 e-mail birmgham@aalco.co.uk CHEPSTOW Tel 09 6 6 Fax 09 6 600 e-mail chepstow@aalco.co.uk DYFED Tel 069 Fax 069 5276 e-mail dyfed@aalco.co.uk ESSEX Tel 06 0 Fax 06 2 e-mail essex@aalco.co.uk LEEDS Tel 0 276 00 Fax 0 276 02 e-mail leeds@aalco.co.uk LIVERPOOL Tel 05 7 55 Fax 05 7 2657 e-mail liverpool@aalco.co.uk MANCHESTER Tel 00 656 Fax 00 60 e-mail manchester@aalco.co.uk NEWCASTLE Tel 09 9 Fax 09 9 77 e-mail newcastle@aalco.co.uk NORWICH Tel 00 777 Fax 00 79999 e-mail norwich@aalco.co.uk NOTTINGHAM Tel 05 9 2600 Fax 05 9 266 e-mail nottgham@aalco.co.uk SOUTHAMPTON Tel 02 07 50 Fax 02 07 5275 e-mail southampton@aalco.co.uk GLASGOW Tel 0 66 0 Fax 0 66 260 e-mail glasgow@aalco.co.uk HULL Tel 0 626262 Fax 0 62626 e-mail hull@aalco.co.uk Also available Ireland DUBLIN Tel +5 629 600 Fax +5 6299 0 e-mail: dubl@amari-dubl.com AALCO is a registered trademark of Aalco Metals Ltd STOKE Tel 072 75700 Fax 072 7570 e-mail stoke@aalco.co.uk SWANLEY Tel 022 60900 Fax 022 6090 e-mail swanley@aalco.co.uk CORK Tel +5 2 0 5 Fax +5 2 0 59 e-mail: cork@amari-cork.com Designed and produced by Squarefox Design Limited www.squarefox.co.uk