ORDERING DT: SERIES 560 PROXIMITY ES TO ORDER SPECIFY: Type, Cord Type, Sensing Circuitry, Design No., and Cable Length. TYPE Hall, Reed, Magnetoresistive CBLE LENGTH 02-2 meter length cable (Leave blank when quick connect is specified) 56 0 2-2 - 02 CORD TYPE 0 - Cabled 2 - Quick Connect NOTES: ) Cordsets for quick connect switches must be ordered separately. 2) Other cable lengths available. Consult PHD. SENSING CIRCUITRY DESCRIPTION COLOR 2-2 NPN or PNP Reed White - NPN Hall Yellow 4- PNP Hall Red 5- NPN Solid State Black 6- PNP Solid State Orange 9-2 C Reed w/current Limiting Green CORDSETS WITH QUICK CONNECT PRT NO. LENGTH 6549-02 2 meter 6549-05 5 meter ES 9-6 PHDV www.phdinc.com/products/switchesandsensors (800) 624-85
BENEFITS: SERIES 560 HLL EFFECT ES BENEFITS Series 560 Hall Effect Switches are available for use on selected PHD products, making it easy to interface these actuators with various electronic controls. Switches have no moving parts or mechanical contacts, providing long switch life and elimination of contact bounce. Constant amplitude output is provided for use with most digital logic systems. Low profile integral clamp mounting is easy to adjust over the entire piston travel of the cylinder or actuator. Several switches may be mounted to control or initiate any sequence or function. Dual LED indicators provide convenient means for positioning and troubleshooting circuits. Green LED shows that power is being received at the switch and amber shows when the switch output is on. vailable in a Quick Connect model for easy installation and maintenance. Series 560 Hall Effect Switches are designed specifically to provide an input signal to various types of programmable controllers or logic systems. Since Hall Effect Switches are solid-state, there are no moving parts to wear out. They offer an infinite number of troublefree operations. Hall Effect Switches operate on current only. SPECIFICTIONS 560 & 562 5604 & 5624 OPERTING PRINCIPLE Hall Effect CTUTED BY Moving Magnet INPUT VOLTGE 4.5 to 24 V OUTPUT TYPE NPN (Sink) PNP (Source) CURRENT RTING 20 m. Max. 00 m. Max. VOLTGE DROP.5 V Max. BURDEN 2 m. Max. ENVIRONMENTL IP67 OPERTING TEMP. 0 to 80 C MODEL NO. 560 & 562 - NPN (SINK) INPUT - 4.5-24 V CURRENT - 20 m. MX. HOUSING COLOR - YELLOW (LED s have been omitted from the schematic for clarity.) CBLED MODEL 560 QUICK CONNECT MODEL 562 PIN HLL EFFECT WIRING SCHEMTICS 2/4 MODEL NO. 5604 & 5624 - PNP (SOURCE) INPUT - 4.5-24 V CURRENT - 00 m. MX. HOUSING COLOR - RED (LED s have been omitted from the schematic for clarity.) CBLED MODEL 5604 QUICK CONNECT MODEL 5624 PIN 2/4 ES www.phdinc.com/products/switchesandsensors (800) 624-85 PHDV 9-7
BENEFITS: SERIES 560 SOLID STTE ES BENEFITS Series 560 Solid State Switches are available for use on selected PHD products, making it easy to interface these actuators with various electronic controls. Switches are solid state, having no moving parts or mechanical contacts, providing long switch life and elimination of contact bounce. Transient voltage protection. Constant amplitude output is provided for use with most digital logic systems. Reverse polarity protection. Low profile integral clamp mounting is easy to adjust over the entire piston travel of the cylinder or actuator. Several switches may be mounted to control or initiate any sequence or function. Dual LED indicators provide convenient means for positioning and troubleshooting circuits. Green LED shows that power is being received at the switch and amber shows when the switch output is on. vailable in a Quick Connect model for easy installation and maintenance. Series 560 Solid State Switches are designed specifically to provide an input signal to various types of programmable controllers or logic systems. Since Solid State Switches have no moving parts to wear out, they offer an infinite number of troublefree operations. Solid State Switches operate on current only. SPECIFICTIONS 5605 & 5625 5606 & 5626 OPERTING PRINCIPLE Solid State CTUTED BY Moving Magnet INPUT VOLTGE 6 to 24 V Max. OUTPUT TYPE NPN (Sink) PNP (Source) CURRENT RTING 20 m. Max. 00 m. Max. VOLTGE DROP.5 V Max. BURDEN 2 m. Max. ENVIRONMENTL IP67* OPERTING TEMP. 0 to 80 C ES MODEL NO. 5605 & 5625 - NPN (SINK) INPUT - 6-24 V CURRENT - 20 m. MX. HOUSING COLOR - (LED s have been omitted from the schematic for clarity.) CBLED MODEL 5605 QUICK CONNECT MODEL 5625 PIN SOLID STTE WIRING SCHEMTICS 2/4 MODEL NO. 5606 & 5626 - PNP (SOURCE) INPUT - 6-24 V CURRENT - 00 m. MX. HOUSING COLOR - ORNGE (LED s have been omitted from the schematic for clarity.) CBLED MODEL 5606 QUICK CONNECT MODEL 5626 PIN 2/4 9-8 PHDV www.phdinc.com/products/switchesandsensors (800) 624-85
DIMENSIONS: SERIES 560 HLL/SOLID STTE ES HLL EFFECT ND SOLID STTE.20 [8.].50 [.8] 2 m CBLE x Ø.4 [.40].460 [.7].06 [.5].25 [8.2].580 [4.7].26 [.2].700 [7.8].290 [7.4] HLL EFFECT ND SOLID STTE WITH MLE QUICK CONNECT.20 [8.].50 [.8] CBLE x Ø.4 [.40].460 [.7] [M8x].06 [.5].25 [8.].580 [4.7].26 [.2] (5.590 [42]) 4.000 [02.0].290.700 [7.4] [7.8] 6549-xx CORDSET WITH FEMLE QUICK CONNECT.402 [0.2] PIN.689 [9.].299 [4.8] CBLE x.77 [4.5] MODEL NO. 6549-02 6549-05 LETTER DIM. 78.74 [2 m] 96.85 [5 m] NUMBERS IN [ ] RE IN mm IMPERIL EQUIVLENTS RE PROVIDED FOR CONVENIENCE ES ll dimensions are reference only unless specifically toleranced. www.phdinc.com/products/switchesandsensors (800) 624-85 PHDV 9-9
BENEFITS: SERIES 560 REED ES BENEFITS Series 560 Reed Switches are available for use on selected PHD products, making it easy to interface these actuators with various electronic controls. Low profile integral clamp mounting is easy to adjust over the entire piston travel of the cylinder or actuator. Several switches may be mounted to control or initiate any sequence or function. n LED indicator provides convenient means for positioning and troubleshooting circuits. vailable in a Quick Connect model for easy installation and maintenance. Special current limit model available for C applications where inrush might otherwise damage the switch. Series 560 Reed Switches are available in either C or models. They are ideal for use as inputs for many types of sequencers and programmable controllers. In some cases, they can be used to drive some relays or valve solenoids. However, electrical transients (inrush currents or line spikes) associated with inductive or capacitive loads can damage and shorten the life of the switch. 5609-2* SPECIFICTIONS 5602-2 & 5622-2 & 5629-2* OPERTING PRINCIPLE Magnetic Reed CTUTED BY Moving Magnet INPUT VOLTGE 4.5 to 24 V 0 to 20 VC OUTPUT TYPE Contact Closure POWER CPCITY 4 Watt Max. 2.5 Watt Max. CURRENT RTING 200 m. Max. Inter. Limited to 20 m. CONTCT RESISTNCE.200 Ohms Max..5 kohm ENVIRONMENTL IEC IP67 OPERTING TEMP. 0 to 80 C * CE certification not applicable to these switch models. DIMENSIONS: SERIES 560 REED ES REED REED WITH MLE QUICK CONNECT.20 [8.].50 [.8] CBLE x Ø.4 [.40] ES.460 [.7].06 [.5].25 [8.].580 [4.7].26 [.2] MODEL NO. 5602-2 &5622-2 5609-2 & 5629-2 [M8x] (5.590 [42]) LETTER DIM. B.685 [7.4].090 [27.7].895 [22.7].00 [] 4.000 [02.0].290.700 [7.4] [7.8] NUMBERS IN [ ] RE IN mm IMPERIL EQUIVLENTS RE PROVIDED FOR CONVENIENCE 6549-xx CORDSET WITH FEMLE QUICK CONNECT.402 [0.2] PIN.689 [9.].299 [4.8] CBLE x.77 [4.5] MODEL NO. 6549-02 6549-05 LETTER DIM. 78.74 [2 m] 96.85 [5 m] 9-0 PHDV NUMBERS IN [ ] RE IN mm IMPERIL EQUIVLENTS RE PROVIDED FOR CONVENIENCE ll dimensions are reference only unless specifically toleranced. www.phdinc.com/products/switchesandsensors (800) 624-85
ENGINEERING DT: SERIES 560 REED ES REED WIRING SCHEMTICS MODEL NO. 5609-2 & 5629-2 INPUT - 0-20 VC ED POWER - 2.5 WTT MX. INTERNL RESISTNCE -.5 kohm HOUSING COLOR - GREEN CBLED MODEL 5609-2 QUICK CONNECT MODEL 5629-2 PIN LINE LINE MODEL NO. 5602-2 & 5622-2 - NPN (SINK) OR PNP (SOURCE) INPUT - 4.5-24 V POWER CPCITY - 4 WTT MX. CURRENT - 200 m. MX. ES 2/4 HOUSING COLOR - WHITE (Bi-polar LED emits a green light in the Sinking circuit and a red light in the Sourcing circuit.) CBLED MODEL 5602-2 - NPN (SINK) QUICK CONNECT MODEL 5622-2 - NPN (SINK) 2/4 PIN CBLED MODEL 5602-2 - PNP (SOURCE) QUICK CONNECT MODEL 5622-2 - PNP (SOURCE) PIN 2/4 ll dimensions are reference only unless specifically toleranced. www.phdinc.com/products/switchesandsensors (800) 624-85 PHDV 9-
ORDERING DT: SERIES 6250 PROXIMITY ES TO ORDER SPECIFY: Type, Cord Type, Sensing Circuitry, Design No., and Cable Length. TYPE Reed, Magnetoresistive CBLE LENGTH 02-2 meter length cable (Leave blank when quick connect is specified) 625 0 7- - 02 CORD TYPE 0 - Cabled - Quick Connect NOTES: ) Cordsets for quick connect switches must be ordered separately. 2) Other cable lengths available. Consult PHD. SENSING CIRCUITRY DESCRIPTION COLOR 5- NPN (Sink) Solid State Brown 6- PNP (Source) Solid State Tan 7- C/ Reed Silver CORDSETS WITH QUICK CONNECT PRT NO. 697-02 697-05 CBLE LENGTH 2 meter/ wire 5 meter/ wire NOTE: This cordset is used for both -wire and 2-wire applications. When used in 2-wire applications, refer to the schematic and disregard the black wire. ES 9-2 PHDV www.phdinc.com/products/switchesandsensors (800) 624-85
BENEFITS: SERIES 6250 REED ES BENEFITS Series 6250 Reed Switches are available for use with PHD ISO Cylinder and on other select PHD actuators which use the M magnet option. Series 6250 Reed Switches offer both 20 VC or 0 to 0 V sink and source operation for maximum flexibility in interfacing with various electronic controls. Special current limiting feature is designed into each switch for protection against potential current inrush damage to switch components. Integral clamp mounting provides easy attachment and adjustment while eliminating the cost of brackets and additional hardware. Several switches may be used on an actuator to control or initiate a sequence or function. LED indicator provides convenient means for positioning and troubleshooting circuits. Switches include either a hard wired 24 WG, Polyurethane (PUR) jacketed cable making it virtually impervious to chemical or environmental damage, or an integral 8 mm screw type connector mounted directly on the switch. IP67 Environmental Protection SPECIFICTIONS 62507-6257- COLOR Silver OPERTING PRINCIPLE Magnetic Reed CTUTED BY Moving Magnet INPUT VOLTGE 0 to 0 V or 0-20 VC* OUTPUT VOLTGE Contact Closure POWER CPCITY 2.5 Watt Max. CURRENT RTING Internally Limited to 25 m. IMPEDNCE 2.25 k Ohm ENVIRONMENTL IP67 OPERTING TEMP. 0 to 80 C * CE certification applicable to 0 to 0 V range only. MODEL NO. 62507- & 6257- INPUT - 0-20 VC POWER CPCITY - 2.5 WTTS MX. CURRENT - 25 m. MX. INTERNL RESISTNCE - 2.25 k Ohm HOUSING COLOR - SILVER CBLED MODEL 62507- PIN QUICK CONNECT MODEL 6257- LINE LINE REED WIRING SCHEMTICS lternate load position for sink circuit lternate load position for sink circuit 2/4 MODEL NO. 62507- & 6257- INPUT - 0 to 0 V POWER CPCITY - 2.5 WTTS MX. CURRENT - 25 m. MX. HOUSING COLOR - SILVER CBLED MODEL 62507- lternate load position for sink circuit QUICK CONNECT MODEL 6257- lternate load position for PIN sink circuit 2/4 ES www.phdinc.com/products/switchesandsensors (800) 624-85 PHDV 9-
BENEFITS: SERIES 6250 SOLID STTE ES BENEFITS Series 6250 Solid State Switches are available for use with PHD ISO Cylinders and on other select PHD actuators which use the M magnet option vailable in both current sinking or current sourcing models for maximum flexibility in interfacing with various electronic controls. Series 6250 Solid State Switch circuitry protects against voltage surges and other electrical anomalies associated with operating systems. Integral clamp mounting provides easy attachment and adjustment while eliminating the cost of brackets and additional hardware. Several switches may be mounted to control or initiate any sequence or function. n LED indicator provides convenient means for positioning and troubleshooting circuits. Switches include either a hard wired 24 WG, Polyurethane (PUR) jacketed cable making it virtually impervious to chemical or environmental damage, or an integral 8mm screw type connector mounted directly on the switch. IP67 Environmental Protection Series 6250 Solid State Switches are designed specifically to provide an input signal to various types of programmable controllers or logic systems. Since Solid State Switches have no moving parts to wear out, they offer an infinite number of troublefree operations. Solid State Switches operate on current only. 62505- & 62506- & SPECIFICTIONS 6255-6256- COLOR Brown Tan OPERTING PRINCIPLE Magnetoresistive CTUTED BY Moving Magnet INPUT VOLTGE 0 to 0 V OUTPUT TYPE NPN (Sink) PNP (Source) CURRENT RTING 00 m. Max. 00m. Max. VOLTGE DROP.5 V Max. BURDEN 2 m. Max. ENVIRONMENTL IP67 OPERTING TEMP. 0 to 80 C ES MODEL NO. 62505- & 6255- - NPN - (SINK) INPUT - 0-0 V CURRENT - 00 m. MX. HOUSING COLOR - (LED has been omitted from the schematic for clarity.) CBLED MODEL 62505- MR MGNETORESISTIVE WIRING SCHEMTICS MODEL NO. 62506- & 6256- - PNP - (SOURCE) INPUT - 0-0 V CURRENT - 00 m. MX. HOUSING COLOR - TN (LED has been omitted from the schematic for clarity.) CBLED MODEL 62506- MR QUICK CONNECT MODEL 6255- PIN MR 2/4 2/4 QUICK CONNECT MODEL 6256- PIN MR 2/4 2/4 9-4 PHDV www.phdinc.com/products/switchesandsensors (800) 624-85
DIMENSIONS: SERIES 6250 REED/SOLID STTE ES REED ND SOLID STTE WITH QUICK CONNECT SGNL.20 [5.2].660 [6.7] M8 THRED.876 [22.].80 [9.6].660 [6.7].088 [27.6].682 [7.].50 [2.8].8 [8.].07 [.8] REED ND SOLID STTE CBLED.50 [2.8].80 [9.6].58 [4].07 [.8].8 [8.].8 [4.6].660 [6.7].088 [27.6].682 [7.] 697-xx CORDSET WITH FEMLE QUICK CONNECT.5 [8.5] PIN - WIRE CBLE x.77 [4.5] - WIRE - COLOR MODEL NO. 697-02 697-05 LETTER DIM. LENGTH 78.7 wire [2000] 97.0 wire [5000] NUMBERS IN [ ] RE IN mm IMPERIL EQUIVLENTS RE PROVIDED FOR CONVENIENCE NOTE: THIS CORDSET IS USED FOR BOTH -WIRE ND 2-WIRE PPLICTIONS. WHEN USED IN 2-WIRE PPLICTIONS, REFER TO THE SCHEMTIC ND DISREGRD THE WIRE. ES ll dimensions are reference only unless specifically toleranced. www.phdinc.com/products/switchesandsensors (800) 624-85 PHDV 9-5
ORDERING DT: SERIES 750 ES ORDERING DT TO ORDER SPECIFY: Type, Cord Type, Sensing Circuitry, Design No., and Cable Length. CORD TYPE 0 - Cabled 2 - Quick Connect TYPE Solid State, Reed 75 0 CBLE LENGTH 06-6 ft [.8 m] length cable (Leave blank when quick connect is specified) 2-2 SENSING CIRCUITRY DESCRIPTION COLOR 2-2 NPN or PNP Reed White -2 NPN Solid State Yellow 4-2 PNP Solid State Red 9- *C Reed w/current Limiting Green CORDSETS WITH QUICK CONNECT PRT NO. LENGTH 6549-02 2 meter 6549-05 5 meter 06 - NOTES: ) Cordsets for quick connect switches must be ordered separately. See page 9-7. 2) Other cable lengths available. Consult PHD. ) *CE certification not applicable to the C Reed with Current Limiting model. COMMON BENEFITS Series 750 switches are available for use on most Tom Thumb and PHD products for simple interfacing to many types of electrical controllers. The compact low profile design saves space and provides mounting versatility. Low profile bracket attaches securely across two tie rods and allows easy position adjustment over the entire piston travel of the cylinder or actuator. IP67 Environmental Protection Red LED indicator provides convenient method for position setting and troubleshooting. vailable in a cabled or 8 mm threaded Quick Connect model for easy installation and maintenance. 24 WG polyurethane (PUR) jacketed cable is robust and virtually impervious to chemical and environmental damage. Multiple switches may be mounted to control or initiate any sequence or function. ES REED BENEFITS vailable as either 0-0 V or 0-20 VC models for simple interfacing to sequencers and programmable controllers. Can be used to directly drive some types of relays or valve solenoids. SOLID STTE BENEFITS Solid state switches afford long life. Constant amplitude output allows use with most digital logic systems. Switch circuitry protects against voltage surges and other electrical anomalies associated with operating systems. Excellent switch hysteresis characteristics and symmetry. Offered in 0-0 V current sinking and current sourcing versions for simple interfacing to electronic system controllers. 9-6 PHDV www.phdinc.com/products/switchesandsensors (800) 624-85
DIMENSIONS: SERIES 750 ES SOLID STTE MLE QUICK CONNECT Detail Ø.200 [4.6] LED INDICTOR.47 [2] 4 TYP.2 [8.2].286 [7.] 6 ft [.8 m] CBLE x Ø.77 [4.5].000 [25.4].78 [4.52].22 [8.2] REED MLE QUICK CONNECT DETIL Ø.200 [4.6] LED INDICTOR.47 [2.0].2 [8.2] 4 TYP.286 [7.] 6 ft [.8 m] CBLE x Ø.77 [4.5] 4.000 [0.6] (5.590 [42]).47 [2.0] 4 TYP.286 [7.].000 [25.4].78 [4.52].22 [8.2].028 [.7] Ø.77 [4.5] M8x.4 [8].2.78 [8.2][4.52].22 [8.2].028 [.7] BRCKETS 7000-xx-5 7000--5 7000-2-5 7000--5 7000-4-5 7000-xx-0 BRCKET DOES NOT EXTEND BEYOND CYLINDER OUTLINE ON THIS SIDE.500 [2.7] MX PRT NUMBER 7494 842.44 [.7] MX.429 [0.9] MX DESCRIPTION Strain relief kit for non -5 brackets (-5-0 through -4-0) Strain relief kit for Series SD/SE Slide size 26 LED INDICTOR.000 [25.4].700 [7.8].000 [25.4] LED INDICTOR *-/4" Bore C & C Cylinders require switch bracket 542-54-. SERIES V & HV E, EL, & NE NPG CYLINDERS BORE SIZE IMPERIL /4 -/8 -/8 /4 -/8 -/8 2 -/8 -/8 METRIC 9 25 29 5 9 29 5 5 75 29 5 IMPERIL LRGE BORE CYLINDERS BORE SIZE COMPCT BRCKETS* -/2 7000-5-0 2 7000-5-0 2-/2 7000-5-0 -/4* 7000-5-0 4 7000-5-0 5, 6, & 8 7000-57-0 COMPCT BRCKETS 7000--5 7000-2-5 7000--5 7000-4-5 7000-5-0 7000-6-0 7000-7-0 7000-40-0 7000-4-0 7000--5 7000-6-0 SD/SE SLIDES BORE SIZE 22 2 24 25 26 BRCKET 7000--5 7000-2-5 7000--5 7000-4-5 58050-02 7000-5-0 7000-6-0 7000-7-0 7000-40-0 7000-4-0.7 [.5] MX BRCKET DOES NOT EXTEND BEYOND CYLINDER OUTLINE ON THIS SIDE.690 [7.5] NUMBERS IN [ ] RE IN mm IMPERIL EQUIVLENTS RE PROVIDED FOR CONVENIENCE 6549-xx CORDSET WITH FEMLE QUICK CONNECT WIRE COLOR Ø.402 [0.2] PIN.299 [4.8].689 [9.] CONNECTOR CBLE L SERIES 000 & 2000 000 & 4000 5000 & 6000 7000 & 8000 MINITURE ll dimensions are reference only unless specifically toleranced. LINER SECTION 7000-6-0 7000-7-0 7000-40-0 7000-4-0 7000-5-0 www.phdinc.com/products/switchesandsensors (800) 624-85 ROTRY & MULTI-MOTION CTUTORS COMPCT BRCKETS ROTRY SECTION 7000-2-5 7000-4-5 7000-8-0 7000-9-0 LETTER DIM. MODEL NO. L 78.74 6549-02 [2 m] 96.85 6549-05 [5 m] NOTES: ) For alternative supplier part numbers, see page 9-5. 2) For earlier design switches 752x- and 7529-2, use cordset 75-00-02 or 75-00-05. PHDV ES 9-7
SPECIFICTIONS: SERIES 750 ES SPECIFICTIONS 750-2 & 752-2 7504-2 & 7524-2 OPERTING PRINCIPLE Solid State CTUTED BY Piston Magnet INPUT VOLTGE 0-0 V OUTPUT TYPE NPN (Sink) PNP (Source) CURRENT RTING 20 m. Max 00 m. Max VOLTGE DROP.5 V BURDEN 0 m. Max. ENVIRONMENTL IP67 OPERTING TEMP. 0 to 80 C 7502-2 7509-* SPECIFICTIONS 7522-2 7529-* OPERTING PRINCIPLE Magnetic Reed CTUTED BY Piston Magnet INPUT VOLTGE 0-0 V 0-20 VC POWER CPCITY 0 Watt Max. 0 Watt Max. OUTPUT TYPE Contact Closure CURRENT RTING 200 m. Inter. Limited Switched to 85 m. CONTCT RESISTNCE. Ohm Max.. Ohm Max. ENVIRONMENTL IP67 OPERTING TEMP. 0 to 80 C * CE certification not applicable to these switch models. MODEL NO. 750-2 & 752-2 - NPN (SINK) INPUT - 0-0 V CURRENT - 20 m. MX. HOUSING COLOR - YELLOW (LED s have been omitted from the schematic for clarity.) CBLED MODEL 750-2 QUICK CONNECT MODEL 752-2 PIN SOLID STTE WIRING SCHEMTICS 2/4 MODEL NO. 7504-2 & 7524-2 - PNP (SOURCE) INPUT - 0-0 V CURRENT - 00 m. MX. HOUSING COLOR - RED (LED s have been omitted from the schematic for clarity.) CBLED MODEL 7504-2 QUICK CONNECT MODEL 7524-2 PIN 2/4 ES 9-8 PHDV REED WIRING SCHEMTICS MODEL NO. 7502-2 & 7522-2 - NPN (SINK) OR PNP (SOURCE) INPUT - 0-0 V POWER CPCITY - WTT MX. CURRENT - 200 m. MX. HOUSING COLOR - WHITE (Bi-polar LED emits a red light.) CBLED MODEL 7502-2 - NPN (SINK) QUICK CONNECT MODEL 7522-2 - NPN (SINK) PIN CBLED MODEL 7502-2 - PNP (SOURCE) QUICK CONNECT MODEL 7522-2 - PNP (SOURCE) PIN 2/4 2/4 MODEL NO. 7509- & 7529- INPUT - 20 VC ED POWER - WTT MX. INTERNL RESISTNCE -.5 kohm HOUSING COLOR - GREEN CBLED MODEL 7509- PIN QUICK CONNECT MODEL 7529- www.phdinc.com/products/switchesandsensors (800) 624-85 LINE LINE 2/4
ORDERING DT: SERIES 5580 PROXIMITY ES TO ORDER SPECIFY: Type, Cord Type, Sensing Circuitry, Design No., and Cable Length. TYPE Hall, Reed 558 0 CBLE LENGTH 02-2 meter length cable (Leave blank when quick connect is specified) 2- - 02 CORDSETS WITH QUICK CONNECT PRT NO. LENGTH 6549-02 2 meter 6549-05 5 meter CORD TYPE 0 - Cabled 2 - Quick Connect NOTES: ) Cordsets for quick connect switches must be ordered separately. 2) Other cable lengths available. Consult PHD. SENSING CIRCUITRY DESCRIPTION COLOR 2 - NPN or PNP Reed White - NPN Hall Yellow 4 - PNP Hall Red BENEFITS Series 5580 Proximity Switches are available for use on selected PHD products making it easy to interface these actuators with various electronic controls. Hall Effect Switches are solid state for long life and elimination of contact bounce. Constant amplitude output is provided for use with most digital logic systems. Low profile mounting is easy to adjust at the ends of travel of the slide or gripper. LED indicator provides convenient means for positioning and troubleshooting circuits. n LED shows when the switch output is on. vailable in a Quick Connect model for easy installation and maintenance. HLL EFFECT PHD Series 5580 Hall Effect Proximity Switches are designed specifically to provide an input signal to various types of programmable controllers or logic systems. Since Hall Effect Switches are solid-state, there are no moving parts to wear out. The switches offer an infinite number of trouble-free operations. Hall Effect Switches operate on current only. SPECIFICTIONS 5580 & 5582 55804 & 55824 OPERTING PRINCIPLE Hall Effect CTUTED BY Target Magnet INPUT VOLTGE 4.5 to 24 V OUTPUT TYPE NPN (Sink) PNP (Source) CURRENT RTING 20 m. Max. 00 m. Max. VOLTGE DROP.5 V Max. BURDEN 2 m. Max. ENVIRONMENTL IP67 OPERTING TEMP. 0 to 80 C REED PHD Series 5580 Reed Switches are available in a model. They are ideal for use as inputs for many types of sequencers and programmable controllers. In some cases, they can be used to drive some relays or valve solenoids. However, electrical transients (inrush currents or line spikes) associated with inductive or capacitive loads can damage and shorten the life of the switch. SPECIFICTIONS 55802 & 55822 OPERTING PRINCIPLE Magnetic Reed CTUTED BY Target Magnet INPUT VOLTGE 4.5 to 24 V OUTPUT TYPE NPN (Sink) or PNP (Source) CURRENT RTING 200 m. Switched CONTCT RESISTNCE.090 Ohm Max. ENVIRONMENTL IP67 OPERTING TEMP. 0 to 80 C ES www.phdinc.com/products/switchesandsensors (800) 624-85 PHDV 9-9
DIMENSIONS: SERIES 5580 PROXIMITY ES HLL EFFECT ND REED.8 [.0] 2 m CBLE x Ø.4 [.4].8 [.0].80 [0.0].26 [6.0]SQ HLL EFFECT ND REED WITH MLE QUICK CONNECT CBLE x.4 [.40] [M8x] (5.550 [4]) 4.000 [02.0].80 [0.0].26 [6.0] SQ 6549-xx CORDSET WITH FEMLE QUICK CONNECT.402 [0.2] PIN.689 [9.].299 [4.8] CBLE x.77 [4.5] MODEL NO. 6549-02 6549-05 LETTER DIM. 78.74 [2 m] 96.85 [5 m] NUMBERS IN [ ] RE IN mm IMPERIL EQUIVLENTS RE PROVIDED FOR CONVENIENCE MODEL NO. 5580 & 5582 - NPN (SINK) INPUT - 4.5-24 V CURRENT - 20 m. MX. HOUSING COLOR - YELLOW (LED has been omitted from the schematic for clarity.) CBLED MODEL 5580 PIN QUICK CONNECT MODEL 5582 HLL EFFECT WIRING SCHEMTICS 2/4 MODEL NO. 55804 & 55824 - PNP (SOURCE) INPUT - 4.5-24 V CURRENT - 00 m. MX. HOUSING COLOR - RED (LED has been omitted from the schematic for clarity.) CBLED MODEL 55804 PIN QUICK CONNECT MODEL 55824 2/4 ES REED WIRING SCHEMTICS MODEL NO. 55802 & 55822 - NPN (SINK) OR PNP (SOURCE) CURRENT - 200 m. MX. INPUT - 4.5-24 V HOUSING COLOR - WHITE (Bi-polar LED emits a green light in the Sinking circuit and a red light in the Sourcing circuit.) CBLED MODEL 55802 - NPN (SINK) CBLED MODEL 55802 - PNP (SOURCE) QUICK CONNECT MODEL 55822 - NPN (SINK) 2/4 PIN QUICK CONNECT MODEL 55822 - PNP (SOURCE) PIN 2/4 9-20 PHDV ll dimensions are reference only unless specifically toleranced. www.phdinc.com/products/switchesandsensors (800) 624-85
ORDERING DT: MODEL 6790 ES ORDERING DT TO ORDER SPECIFY: Product Type, Cable Type, Sensing Circuitry, Cable Length CBLE TYPE 0 - Cabled 2 - Quick Connect CBLE LENGTH 05-5 meter length cable Leave blank when quick connect is specified CORDSETS WITH QUICK CONNECT PRT NO. LENGTH 6549-02 2 meter 6549-05 5 meter 679 0 2- - 05 NOTES: ) Cordsets for quick connects must be ordered separately. 2) *C Reed (9-2) available with quick connect only. PRODUCT TYPE Reed SENSING CIRCUITRY 2- PNP or NPN Reed 9-2 C Reed VILBLE MODELS 67902--05 67922-67929-2 BENEFITS Model 6790 Switches are available for use on many actuators. Saving space and providing mounting versatility, the round design fits into grooves in the body of the actuator. IP67 Environmental Protection LED indicator provides convenient method for position setting and troubleshooting. vailable in 8 mm threaded Quick Connect model for easy installation and maintenance. 28 WG Polyurethane (PUR) jacketed cable Multiple switches may be mounted to control or initiate any sequence or function. vailable in 4.5-0 V or 65-20 VC models for simple interfacing to sequencers and programmable controllers. Can be used to directly drive some types of relays or valve solenoids within the switch specifications stated. SPECIFICTIONS OPERTING PRINCIPLE CTUTED BY INPUT VOLTGE OUTPUT TYPE CURRENT RTING ENVIRONMENTL OPERTING TEMP. IMPEDNCE 67902 & 67922 67929 Magnetic Reed Piston Magnet 4.5-0 V 65-20 VC Contact Closure 50 m Max. 25 m Max. IP67-20 to 85 C.2 Ohm Max.5 k Ohm ES www.phdinc.com/products/switchesandsensors (800) 624-85 PHDV 9-2
BENEFITS: MODEL 6790 ES LED.00 [27.9].777 [9.7].6 [.5].095 [2.4] -48 x /6 [4.8] SET SCREW.050 [.] HEX*.078 [2].08 [2.7].56 [.9].4 [.4] MLE QUICK CONNECT DETIL 2.0 [05].76 [44] M8 x THRED.260 [6.6] Ø.5 [8].26 [6].02 [2.6].80 [4.6] *MX. SCREW TORQUE.0 in-lb [.0 Nm] METRIC INFORMTION SHOWN IN [ ] CURRENT: 50 m. MX. HOUSING COLOR: (Bi-polar LED emits a yellow light) CBLED MODEL 6790 PIN QUICK CONNECT Ø.402 MODEL 6792 [0.2] PIN 6549-xx CORDSET WITH FEMLE QUICK CONNECT MODEL NO. 6790- & 6792- - NPN (SINK) INPUT: 4.5-0 V SOLID STTE WIRING SCHEMTICS.299 [4.8].689 [9.] 2/4 CBLED MODEL 67904 CONNECTOR CBLE L MODEL NO. 67904- & 67924- - PNP (SOURCE) INPUT: 4.5-0 V CURRENT: 50 m. MX. HOUSING COLOR: (Bi-polar LED emits a red light.) QUICK CONNECT MODEL 67924 PIN MODEL NO. 6549-02 6549-05 2/4 LETTER DIM. L 78.74 [2 m] 96.85 [5 m] ES REED WIRING SCHEMTICS MODEL NO. 67902- & 67922- - NPN (SINK) OR PNP (SOURCE) INPUT: 4.5-0 V CURRENT: 50 m. MX. IMPEDNCE:.2 Ohm MX. HOUSING COLOR: (LED emits a red light) CBLED MODEL 67902 - NPN (SINK) QUICK CONNECT MODEL 67922 - NPN (SINK) PIN MODEL NO. 67929-2 INPUT: 65-20 V CURRENT: 25 m. MX. IMPEDNCE:.5 k Ohm HOUSING COLOR: (LED emits a red light) 2/4 CBLED MODEL 67902 - PNP (SOURCE) QUICK CONNECT MODEL 67922 - PNP (SOURCE) PIN C REED WIRING SCHEMTICS QUICK CONNECT MODEL 67929-2 PIN LINE 2/4 2/4 9-22 PHDV ll dimensions are reference only unless specifically toleranced. www.phdinc.com/products/switchesandsensors (800) 624-85
ORDERING DT: MODEL JC ES TO ORDER SPECIFY: Product, Series, Design No., Options, Type, Circuit Type, and Cable Options. PRODUCT J - Switches DESIGN NO. TYPE D- Single Position T- 2 Position Teachable J C S T P - 2 SERIES C - C-Slot Mounting OPTIONS S - Solid State CIRCUIT TYPE N - NPN P - PNP ( 2 position teachable available in PNP only) CBLE OPTIONS K-Quick Connect 2-2 Meter Cable (vailable on JCSTP only) 5-5 Meter Cable (Not available on JCSTP) Current 6790 Switch 67902--02 67902--05 6790--02 6790--05 67904--02 67904--05 67922-6792- 67924-67929-2 switch cross reference chart DESCRIPTION PNP or NPN Reed, 2 meter Cable PNP or NPN Reed, 5 meter Cable NPN Solid State, 2 meter Cable NPN Solid State, 5 meter Cable PNP Solid State, 2 meter Cable PNP Solid State, 5 meter Cable PNP or NPN Reed, Quick Connect NPN Solid State, Quick Connect PNP Solid State, Quick Connect C Reed, Quick Connect New PHD Switch no direct substitute* no direct substitute* JCSDN-5 JCSDN-5 JCSDP-5 JCSDP-5 no direct substitute* JCSDN-K JCSDP-K still available *Consider Solid State to replace Reed. CUTION: If used for 67902--xx or 67922- Switch replacement, power connection (brown and blue leads) may need to be reversed to match connection diagram on page 6. ES 9-2 www.phdinc.com/products/switchesandsensors (800) 624-85 PHDV
BENEFITS: SERIES JC ES TECHBLE Teachable Series JC Switches Teachable switches feature two programmable outputs. Switch is simply mounted in a convenient location, such as middle of travel, then actuator is placed in first desired position and first output is set. Then actuator is placed in second desired position and second output is set. Outputs retain settings even after power interruption. Since each switch provides two outputs, an actuator with only two slots may have up to four outputs by using two switches. Offered in 2 0 V current sourcing (PNP) version only vailable in cabled (2 meter) or quick connect versions. Use two position teachable switches for: Reduced cabling Simplified setup, More sensing positions STNDRD Standard Series JC Switches vailable in cabled (5 meter) or quick connect versions vailable in solid state sensing only for longest life and most reliable operation Offered in 0 0 V current sinking (NPN) and current sourcing (PNP) versions for simple interfacing to system controllers. Replaces PHD Series 6790 Switches (excluding C applications) See chart on page 2. Standard JC Switches can be used on many PHD Standard ctuators ES Common Benefits for Both Styles Fits into 4mm switch slot IP67 Environmental Protection LED indicator for convenient setting and troubleshooting Integrated protection circuitry including short circuit protection Polyurethane (PUR) jacketed cable vailable in solid state sensing only for longest life and most reliable operation Improved switch hysteresis and magnetic response uniformity Quick connect available Recommended PHD Products Use GRIPPERS: Series GRK, EGRK, GRB, GRF (JCSD only), & GRS (JCSD only) ROTRY CTUTORS: Series RI, RCC SLIDES: Series SFP, SFM, SHP, STP, SIP, SMx, & SxL, SxH CYLINDERS: Series CRS & CTS Both switches have a unique housing design which allows drop-in installation from the side, does not have to be inserted from the end of the slot Tilt switch to drop in, then rotate logo up. 9-24 PHDV www.phdinc.com/products/switchesandsensors (800) 624-85
JCSTP-2 JCSTP-K DIMENSIONS: MTCHING CORDSET SERIES JCST TECHBLE ES PRT NO. 8284--00 PNP (Source), Solid State, 2-0 V, 2 meter cable PNP (Source), Solid State, 2-0 V, Quick Connect DESCRIPTION M8, 4 pin, Straight Female Connector, 5 meter cable SERIES JCST TWO POSITION TECHBLE MGNETIC SPECIFICTIONS JCSTP-x OPERTING PRINCIPLE Programmable Magnetic This switch provides the ability to Field identify Characterization two separately programmable INPUT VOLTGE positions with a single switch. 2 - Programmable 0 V capability NUMBER means & TYPE no OF fine-tuning. OUTPUTS With Two switch PNP properly (source), aligned, just place actuator in desired positions separately and program. adjustable Solid-state sensing OUTPUT technology CURRENT provides a highly reliable 00 m switch. max., Elliptical housing allows for easy drop-in installation Short Circuit from Protection the side, and does VOLTGE not have DROP to be inserted from the end of 2.2 the V slot. LED indicators on module BURDEN for positioning and programming. 5 vailable m with 2 meter cable ENVIRONMENTL or 8 mm threaded Quick Connect. IP67 OPERTING TEMP. -20 C to 75 C TYP. DETECTION RE 0-50 mm TECHBLE JCSTP-2.50 [.8] DETECTION RE.750 [95.25].020 [0.5].768 [9.5]. [2.87].8 [0].77 [4.5].256 [6.5] JCSTP-K (Quick Connect) FOR DIMENSIONS SEE BOVE 9.25 [485.78] FOR TECH MODULE DIMENSIONS SEE BOVE.49 [4.] M8 x 8284--00 CORDSET PIN 4 WIRE COLOR WIRE COLOR PIN 2 WIRE COLOR WHITE PIN WIRE COLOR.94 [0] M8 x.200 [0.5] ENGINEERING DT: SERIES JCST TECHBLE ES PRT NO. JCSTP-2 JCSTP-K PRT NO. 8284--00 DESCRIPTION PNP (Source), Solid State, 2-0 V, 2 meter cable PNP (Source), Solid State, 2-0 V, Quick Connect MTCHING CORDSET DESCRIPTION M8, 4 pin, Straight Female Connector, 5 meter cable JCSTP-2 SPECIFICTIONS OPERTING PRINCIPLE INPUT VOLTGE NUMBER & TYPE OF OUTPUTS OUTPUT CURRENT VOLTGE DROP BURDEN ENVIRONMENTL OPERTING TEMP. TYP. DETECTION RE JCSTP-x Programmable Magnetic Field Characterization 2-0 V Two PNP (source), separately adjustable 00 m max., Short Circuit Protection 2.2 V 5 m IP67-20 C to 75 C 0-50 mm ES JCSTP-2 www.phdinc.com/products/switchesandsensors (800) 624-85 [95.25].50 [.8] DETECTION RE.750 9-25 PHDV
PROGRMMING GUIDE: SERIES JC TECHBLE ES ES 9-26 PHDV www.phdinc.com/products/switchesandsensors (800) 624-85
SPECIFICTIONS JCSDP-x JCSDN-x OPERTING PRINCIPLE Solid State Detection of Moving Magnet INPUT VOLTGE 0-0 V OUTPUT TYPE PNP (source) NPN (sink) OUTPUT CURRENT 00 m max., Short Circuit Protection SERIES VOLTGE DROP JCSD MGNETIC 2.5 V This BURDEN switch provides the ability to identify 8 m a single position. Solid-state ENVIRONMENTL sensing technology provides a highly IP67reliable switch. Elliptical OPERTING housing TEMP. allows for easy drop-in -25installation. C to 75 C Includes LED indicator for convenient means of positioning. vailable with PNP or NPN output. vailable with cable or 8 mm threaded Quick Connect. DIMENSIONS: SERIES JCSD STNDRD ES LETTER DIM HS HS GRK-x-5 X 6.5 or 2 in mm.220 5.6.25.2 MODEL NUMBER GRK-x-46 X 8 or 6 GRK-x-58 X 0.5 or 20 GRK-x-75 X 2.5 or 26 in.05.40 mm.4 0.9 in.640 mm 6. in.850 mm 2.6 JCSDx-5.40 [.6].984 [25] JCSDN-x JCSDP-x. [2.8] 96.85 [5 m] MIN JCSDx-K (Quick Connect).40 [.6]. [2.8].984 [25] 9.250 MIN [24.0].49 [4.] M8 x 6549-xx CORDSET.402 [0.2] PIN.689 [9.].299 [4.8] ENGINEERING DT: SERIES JCSD STNDRD ES PRT NO. JCSDP-5 JCSDP-K JCSDN-5 JCSDN-K DESCRIPTION PNP (Source), Solid State, 0-0 V, 5 meter cable PNP (Source), Solid State, 0-0 V, Quick Connect NPN (Sink), Solid State, 0-0 V, 5 meter cable NPN (Sink), Solid State, 0-0 V, Quick Connect MTCHING CORDSET JCSDP-5 & JCSDN-5 JCSDP-K & JCSDN-K 6549-XX PRT NO. 6549-02 6549-05 DESCRIPTION M8, pin, Straight Female Connector, 2 meter cable M8, pin, Straight Female Connector, 5 meter cable SPECIFICTIONS JCSDP-x JCSDN-x OPERTING PRINCIPLE Solid State Detection of Moving Magnet INPUT VOLTGE 0-0 V OUTPUT TYPE PNP (source) NPN (sink) OUTPUT CURRENT 00 m max., Short Circuit Protection VOLTGE DROP 2.5 V BURDEN 8 m ENVIRONMENTL IP67 OPERTING TEMP. -25 C to 75 C ES S HS www.phdinc.com/products/switchesandsensors (800) 624-85 9-27 LETTER DIM PHDV HS HS STNDRD HS 7.0 [8.0] HS (SIZE 5 & 46) (SIZE 58 & 75- HOUSING DOES NOT PROTRUDE BELOW SURFCE OF GRIPPER) GRK-xin.22.2
PPLICTIONS: SERIES JC STNDRD ES Series JCSD Magnetic Switches replace the old style Series 6790 Switches and can be used on all standard PHD Components listed. Series GRF (JCSD only) GRIPPERS: Series GRK, EGRK, GRB, GRF (JCSD only), & GRS (JCSD only) ROTRY CTUTORS: Series RI, RCC SLIDES: Series SFP, SFM, SHP, STP, SIP, SMx, & SxL, SxH CYLINDERS: Series CRS & CTS Series SxH Old Series 6790 Switch Series CR Series CTS Series GRB Series GRS (JCSD only) Series SFM, SFP Series SIP Series STP ES Series RCC Series GRK Series RI Series SHP 9-28 PHDV www.phdinc.com/products/switchesandsensors (800) 624-85
INDUCTIVE PROXIMITY ES 4 mm round 6 mm square PRT NO. 840-00-02 840-002-02 DESCRIPTION NPN (Sink) 0-0 V, 2 meter cable PNP (Source) 0-0 V, 2 meter cable PRT NO. 84-00-02 84-002-02 DESCRIPTION NPN (Sink) 0-0 V, 2 meter cable PNP (Source) 0-0 V, 2 meter cable 8 mm THREDED 2 mm THREDED PRT NO. 5422-005-02 5422-006-02 DESCRIPTION NPN (Sink) 0-0 V, 2 meter cable PNP (Source) 0-0 V, 2 meter cable PRT NO. 556-00 556-002 556-00 DESCRIPTION NPN (Sink) 0-0 V, meter cable PNP (Source) 0-0 V, meter cable 20-250 VC, meter cable BENEFITS High reliability provided by solid state inductive sensing technology. Ease of mounting with PHD s Proximity Switch Bracket Kit and Target Kits for grippers. These kits include all hardware for mounting the switch and the target that is used to actuate the switch. (See Slide and Gripper sections for details.) Suitable for plant environments where dirt and contamination create difficulties for electromechanical and other types of switches. LED indicator circuits are standard on 4 mm round, 6 mm square, and 8 mm threaded and provide a convenient means of positioning and troubleshooting. 840-00-02 840-002-02 SPECIFICTIONS 84-00-02 84-002-02 5422-005-02 5422-006-02 556-00 556-002 556-00 INPUT 2 meter VOLTGE cordset for all Series 0 5580 to 0 Switches V 0 with to 0 Quick V 0 to 0 V 2 meter 0 to 0 cordset V for 0 all to Series 0 V 5580 0 Switches to 0 V with Quick 20 to 250 VC OUTPUT Connect. TYPE Other cable lengths available NPN (Sink) - contact PNP PHD. (Source) NPN (Sink) Connect. PNP (Source) Other cable NPN lengths (Sink) available PNP - (Source) contact PHD. Solid State SENSING RNGE 0.8 mm Max. 0.8 mm Max..5 mm Max..5 mm Max..6 mm Max..6 mm Max..6 mm Max. OUTPUT CURRENT RTING 00 m. Max. 00 m. Max. 200 m. Max. 200 m. Max. 200 m Max. 200 m Max. 0 m Max. BURDEN 0 m. Max. 0 m. Max. 0 m. Max. 0 m. Max. 8 m Max. 8 m Max. VOLTGE DROP 2.5 V Max. 2.5 V Max..0 V Max..0 V Max..5 V Max..5 V Max. V Max. CIRCUIT PROTECTION Yes Yes No No Yes Yes No REVERSE VOLTGE Yes Yes OUTPUT STTE Normally Open Normally Open ENVIRONMENTL IP67 IP68 2 meter cordset for all Series 5580 Switches with Quick Connect. Other cable NPN lengths (Sink) available - contact PHD. MODEL 556-00 840-00-02 84-00-02 5422-005-02 WIRING SCHEMTICS C MODEL 556-00 LINE NEUTRL PNP (Source) MODEL 556-002 840-002-02 84-002-02 5422-006-02 ES www.phdinc.com/products/switchesandsensors (800) 624-85 9-29 PHDV
SERIES 62002 ES SERIES 62002 8 mm ROUND THREDED PROXIMITY PRT NO. 62002--02 DESCRIPTION 8 mm Threaded Reed Switch with 2 meter cable SPECIFICTIONS 62002--02 OPERTING PRINCIPLE Magnetic Reed CTUTED BY Target Magnet INPUT VOLTGE 4.5 to 24 V OUTPUT VOLTGE Contact Closure POWER CPCITY.0 Watt Max. CURRENT RTING 40 m Max. CONTCT RESISTNCE.200 Ohm Max. ENVIRONMENTL IP67 OPERTING TEMP. 0 to 70 C.085 [2.6].075 [27.].990 [25.5].795 [20.9] 2x.60 [4.].220 [5.59] 74.74.79 [900 20].276.040 [7 ].59 [4.99].5 [2.95] 2x.265 [6.7] (M8 x.0-6g THRED) LED IN THIS PPROX LOCTION M8 HEX NUT (2 SUPPLIED).984.080 [25 2.0] SERIES 62002 PROXIMITY WIRING SCHEMTICS MODEL NO. 62002--02 - NPN (SINK) OR PNP (SOURCE) INPUT - 4.5-24 V POWER CPCITY -.0 WTT MX. CURRENT - 40 m MX. ES CBLED MODEL 62002 - PNP (SOURCE) CBLED MODEL 62002 - NPN (SINK) NUMBERS IN [ ] RE IN mm IMPERIL EQUIVLENTS RE PROVIDED FOR CONVENIENCE 9-0 PHDV ll dimensions are reference only unless specifically toleranced. www.phdinc.com/products/switchesandsensors (800) 624-85
BENEFITS: HLL SENSOR WITH SET POINT MODULE BENEFITS Provides independent and fully adjustable multiple position sensing on Series 8400 ngular Grippers, Series 90 & 9 Parallel and 90 ngular Grippers, Series 500 Oval Grippers, and all Rotary ctuators and Multi-Motion ctuators. Independent adjustment of two set point positions from two sensors allows one set point module to interface with two actuators. Or, can be used with a single unit providing 4 adjustable set points throughout jaw travel or rotation. Solid state electronics with Hall Effect sensing technology for an infinite number of trouble-free cycles. Wide signal range capability permits interfacing with most programmable controllers and other logic systems. LED indicators for visual confirmation of each output state. Set Point Module is available for either current sinking or current sourcing models with 4.5 to 24 V output capability. SPECIFICTIONS 9800-0-000 9800-0-0400 OPERTING PRINCIPLE Linear Hall Effect INPUT VOLTGE 8 to 24 V OUTPUT TYPE NPN (Sink) PNP (Source) Open Collector Collector Output OUTPUT VOLTGE 4.5 to 24 V OUTPUT CURRENT RTING 200 m. Max. OUTPUT VOLTGE DROP.4 V Max..5 V Max. at Rated Current at 50 m. BURDEN 50 m. Max. OPERTING TEMP. 0 to 60 C (2 to 40 F) HUMIDITY 5 to 95% (NON CONDENSING) ORDERING DT: HLL SENSOR WITH SET POINT MODULE DUL INPUT SET POINT MODULE PRT NO. 9800-0-000 9800-0-0400 DESCRIPTION NPN (Sink) 4.5-24 V PNP (Source) 4.5-24 V HLL SENSOR KIT FOR SERIES 90, 9, & 8400 MINITURE GRIPPERs PRT NO. IMPERIL METRIC 8674-04 8057-04 8675-04 8058-04 8676-04 8059-04 8677-04 8060-04 8057-04 8058-04 8059-04 8060-04 0906-2 0907-2 0908-2 8686-04 DESCRIPTION Size 6 Models 9x60, 9x6, & 9x62 Parallel Size 7 Models 9x70, 9x7, & 9x72 Parallel Size 8 Models 9x80, 9x8, & 9x82 Parallel Size 9 Models 9x90, 9x9, & 9x92 Parallel Size 0 Model 9x02 ngular Size Model 9x2 ngular Size 2 Model 9x22 ngular Size Model 9x2 ngular 8400 Gripper ngular 840 Gripper ngular 8420 Gripper ngular 840 Gripper ngular INDIVIDUL REPLCEMENT SENSORS PRT NO. DESCRIPTION 0688-2-2 Sensor for all 8600, 7900, and 500 ngular Grippers, and 8600 Parallel Grippers 082---2 Sensor for all Rotary ctuators and Multi-Motion ctuators NOTE: ll sensors come with 2 ft [ m] minimum of shielded cable. HLL EFFECT SENSOR/TRNSDUCER The Sensor/Transducer must be ordered as part of the Gripper or ctuator assembly. The Sensor/Transducer will be mounted to the unit with a transition plate. See individual unit Ordering Data for availability and ordering information. Individual replacement sensors are avai lable as shown. PPLICTIONS GRIPPERS Provides two adjustable sensing positions throughout jaw travel for two grippers (through a single set point module). llows the assurance of part presence by ensuring the jaws have closed or opened to the proper size. Permits go, no go type gauging to occur as parts are gripped. ROTRY CTUTORS & MULTI-MOTION CTUTORS Provides two adjustable sensing positions throughout the 80 rotation of two rotary actuators or multi-motion actuators. Can be used to signal ends of rotation of two units. ES 2 meter cordset for all Series 5580 Switches with Quick www.phdinc.com/products/switchesandsensors (800) 624-85 Connect. Other cable lengths available - contact PHD. PHDV 9-
DIMENSIONS: HLL SENSOR & SET POINT MODULE DUL INPUT SET POINT LOGIC EXMPLE B B B B CSE CSE 2 CSE CSE 4 Both gripper jaws are wide open. No set points are made. The jaws of gripper are closed to grip a part and are wide open on gripper B. One set point is made for gripper. Both gripper jaws are closed to grip a part. Two set points are made, one for gripper and one for gripper B. Gripper jaws are closed all the way (no parts) and Gripper B jaws are closed to grip a part. Two set points for gripper and one set point for gripper B are made. B B CSE 2 CSE 5 CSE 6 4 5 6 Both gripper jaws are closed all the way (no parts). Two set points are made for both grippers and B. In the event one gripper is wide open () and the other is closed all the way (B), only the two set points for the closed gripper would be made. SET POINT OUTPUT 0 0 2 0 0 0 0 B 0 0 B2 0 0 0 0 0688-2-02 basic hall sensor.625 [28.5].500 [.0].25 [28.5].25 [28.5] 2X THRU HOLE FOR #6 SCREWS.75 [9.5].246 [6.0] 2 FT [4 m] OF SHIELDED CBLE IS INCLUDED WITH SENSOR.27 [6.0] SERIES 7900, 8600 -JW, & 500 NGULR GRIPPERS B 0 GRIPPER MODEL NO. 792x, 862x, & 52x 79x, 86x, & 5x 794x, 864x, & 54x 795x, 865x, & 55x.854 [2.5].97 [2.5].2 [28.5].586 [40.5] LETTER DIMENSION B.257 [2.0].540 [9.0].945 [49.5] 2.500 [6.5] C 0.00 [0.0].22 [.0].247 [6.0].44 [.0] C ES SERIES 8400 & 90 ngular grippers C.75 [5.0] B.87 [9.5] GRIPPER MODEL NO. IMPERIL METRIC 840x 9002 84x 902 842x 9022 84x 902.54 [6.5].454 [9.5].704 [46.0] 2.27 [58.0] LETTER DIMENSION B.654 [6.5].554 [4.0].04 [7.6].00 [7.6] C.700 [20.0].900 [25.0].400 [8.0].90 [50.0] SERIES 90 & 9 PRLLEL GRIPPERS.75 [9.5] B.87 [5.0] GRIPPER MODEL NO. 9x6x 9x7x 9x8x 9x9x.47 [6.5].555 [9.5].80 [46.0] 2.28 [58.0] LETTER DIMENSION B.650 [6.5].550 [4.0].295 [7.5].295 [7.5] C.787 [20.0].985 [25.0].496 [8.0].968 [50.0] 9-2 PHDV C ll dimensions are reference only unless specifically toleranced. www.phdinc.com/products/switchesandsensors (800) 624-85
DIMENSIONS: HLL SENSOR & SET POINT MODULE SERIES 000-8000 ROTRY CTUTORS & MULTI-MOTION CTUTORS m SHIELDED CBLE FROM THIS SIDE ON SERIES 000 & 2000 UNITS ONLY.500 [2.7] B m SHIELDED CBLE FROM THIS SIDE ON SERIES 000-8000 UNITS LIMITTIONS: SENSOR MY BE USED ON UNITS WITH MXIMUM ROTTION UP TO ND INCLUDING 80 CTUTOR SERIES 000 & 2000 000 & 4000 5000 & 6000 7000 & 8000 2.980 [75.7] 4.20 [07.4] 4.980 [26.5] 7.980 [202.7] LETTER DIM. B 2.000 [50.8].000 [76.2] 4.000 [0.6] 5.000 [27.0] NUMBERS IN [ ] RE IN mm IMPERIL EQUIVLENTS RE PROVIDED FOR CONVENIENCE SET POINT MODULE #9800-0-0x00.270 [7.0].470 [88.0] 2.220 [56.5].490 [2.5].40 [.5].295 [7.5].750 [22.0].220 [5.5].905 [2.0] + 8-24 V 4X SET POINT DJUSTMENT -0 V TRNS POS TRNS SIG 2.90 [55.6] TRNS SIG B.720 OUTPUT [94.5] OUTPUT 2 4.000.40 [0.5] [86.5] OUTPUT B OUTPUT B2 + 4,5-24 V SOURCE ONLY NUMBERS IN [ ] RE IN mm IMPERIL EQUIVLENTS RE PROVIDED FOR CONVENIENCE 4X SET POINT MDE LED INDICTORS 4X THRU HOLE FOR #8 [M4] SCREW ENGINEERING DT: HLL SENSOR WITH SET POINT MODULE MODEL 9800-0-000 NPN (SINK) WIRING SCHEMTICS Diagrams are typical for many programmable controller interface applications. Modules may also be used to signal TTL. CMOS, relays or solenoids within rated electrical specifications. NOTE: For single applications where four outputs are desired, install a jumper between terminals 4 & 5. INPUT TO PROGRMMBLE CONTROLLER COMMON B 8-24 V POWER SUPPLY RED WHITE RED WHITE OUTPUTS & 2 2 4 5 6 7 8 9 0 MODEL 9800-0-0400 PNP (SOURCE) INPUT TO PROGRMMBLE CONTROLLER COMMON PRIMRY SUPPLY B OUTPUTS B & B2 8-24 V POWER SUPPLY OPTIONL - REQUIRED ONLY IF DESIRED SOURCE OUTPUT VOLTGE IS OTHER THN THT OF PRIMRY SUPPLY RED WHITE RED WHITE OUTPUTS & 2 2 4 5 6 7 8 9 0 IF OUTPUT VOLTGE REQUIRED IS THE SME S THE PRIMRY SUPPLY TTCH JUMPER BETWEEN TERMINLS & 0 ES OUTPUTS B & B2 ll dimensions are reference only unless specifically toleranced. www.phdinc.com/products/switchesandsensors (800) 624-85 9- PHDV
BENEFITS & DIMENSIONS: BRCKETS FOR NFP CYLINDERS BENEFITS llows PHD Series 750 Reed and Hall Effect Switches to be mounted to -/2" [8. mm] to 8" [20.2 mm] bore NFP Cylinders. The brackets flexible design means only two brackets are required to cover 8 sizes of NFP Cylinders. The extruded aluminum bracket attaches securely to a single tierod and does not allow the switch to pull away from the cylinder barrel. The low profile of the switch and bracket saves space and provides additional mounting flexibility. Optional strain relief clamp may be used to protect the switch cable from damage at the switch due to flexing. PRT NO. 7509--06 7502-2-06 7529-7522-2 750-2-06 7504-2-06 752-2 7524-2 PHD MODELS DESCRIPTION C Reed Reed C Reed, Quick Connect Reed, Quick Connect Hall Effect NPN (Sink) Hall Effect PNP (Source) Hall Effect NPN (Sink), Quick Connect Hall Effect PNP (Source), Quick Connect NFP CYLINDER BORE -/2, 2, 2-/2, -/4, & 4 5, 6, & 8 BRCKET NUMBER 7000-5-0 7000-57-0 STRIN RELIEF BRCKET 842 842 See pages 9-6 to 9-8 for switch information. NFP cylinder must have the proper magnetic piston for the PHD Switches to function correctly. 7000-xx-0 NFP BRCKET 842 CBLE RESTRINT KIT OPTIONL CBLE RESTRINT BRCKET REF.000 [25.4] LED INDICTOR B REF C SQ REF D REF DI ES PHD MODELS DESCRIPTION PRT NO. Reed NPN/PNP (White) 7502-2-06 C Reed (Green) 7509--06 Solid State NPN (Yellow) 750-2-06 Solid State PNP (Red) 7504-2-06 BORE SIZE -/2 2 2-/2 -/4 4 5 6 8.75.500.750 2.000 2.75.000.75 4.000 LETTER DIMENSION B C.500 2.000.750 2.500.875.000 2.87.750 2.500 4.500.25 5.500.75 6.500 4.25 8.500 D.250.2.2.75.75.500.500.625 9-4 PHDV ll dimensions are reference only unless specifically toleranced. www.phdinc.com/products/switchesandsensors (800) 624-85