Total solder points: 0 Difficulty level: beginner advanced PIC programmer board K0 This board can program a wide range of Microchip PIC microcontrollers ILLUSTRATED ASSEMBLY MANUAL H0IP-
This device complies with Part of the FCC Rules provided the enclosed instructions are followed to the letter. Use of the device is subject to the following conditions: () this device must not cause harmful interference and () the operation of this device should not be influenced by unwanted interference. More information about FCC can be look at http://www.fcc.gov FR NL UK D S SF I DK SP P Vous trouverez la traduction de cette notice sur le CD, avec d'autres informations Vertaling van deze handleiding, als ook meer gegevens kan men terugvinden op de CD. The translation of this manual and all other information can be found on the CD. Dieübersetzung dieser anleitung und alle anderen Informationen finden Sie auf der CD. Svensk Bruksanvisning och annan information finns på medföljande CD. Tämän käyttöohjeen sekä muun informaation suomenkielinen käännös on oheisella CD:llä. La traduzione di questo manuale e tutte le informazioni concernenti l'unità possono essere trovate sul CD. Oversæ ttelsen af denne manual, samt alle ø vrige informationer vedrø rende enhederne, kan findes på CD'en. La traducción de este manual de instrucciones y toda otra información sobre los dispositivos se encuentran en el CD A traduçã o deste Manual e toda a informaçã o referente às unidades pode ser encontrada no CD
Features & Specifications Features: onboard configurable 0 pin. ZIF socket Microcontroller selection using patch jumper easy to use programming PICprog00 TM software included SUBD connector set included Specifications: power supply: V DC, min. 00mA adapter (Ex. PS0) serial port connector: 9 p. SUBD dimensions: xx0mm /, x, x 0,9" currently supported controllers (rev..0.0.0) : PIC0F00 PICC0A,PICCE PICF9,PICF PICF PICFA PICF0,PICF,PICF,PICF*,PICF* PICF,PICF* PICF,PICFA,PICF,PICFA PICFA* PICF0,PICF PICF0,... (*): under test Minimum system requirements: IBM Compatible PC, Pentium or better Windows? 9/ME/NT/000/XP CDROM drive free REAL serial (RS) port required* (*) The functioning of the PIC programmer card cannot be guaranteed through a USB conversion cable.
Assembly hints. Assembly (Skipping this can lead to troubles! ) Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.. Make sure you have the right tools: A good quality soldering iron (-0W) with a small tip. Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called thinning and will protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning. Thin raisin-core solder. Do not use any flux or grease. A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they cannot fly towards the eyes. Needle nose pliers, for bending leads, or to hold components in place. Small blade and Phillips screwdrivers. A basic range is fine. For some projects, a basic multi-meter is required, or might be handy. Assembly Hints : 0.000 Make sure the skill level matches your experience, to avoid disappointments. Follow the instructions carefully. Read and understand the entire step before you perform each operation. Perform the assembly in the correct order as stated in this manual Position all parts on the PCB (Printed Circuit Board) as shown on the drawings. Values on the circuit diagram are subject to changes. Values in this assembly guide are correct* Use the check-boxes to mark your progress. Please read the included information on safety and customer service * Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as NOTE on a separate leaflet.
Assembly hints. Soldering Hints : - Mount the component against the PCB surface and carefully solder the leads - Make sure the solder joints are cone-shaped and shiny - Trim excess leads as close as possible to the solder joint REMOVE THEM FROM THE TAPE ONE AT A TIME! AXIAL COMPONENTS ARE TAPED IN THE COR- RECT MOUNTING SEQUENCE!
Construction. Diodes. Watch the polarity!. Metal film resistors. Capacitors D : N00 D : N D : N D : N CATHODE D... R.... Resistors R... R0 : ( - - 0 - B - 9) R : 0 ( - - - B - 9). Voltage regulator C : 00nF (0, u) C : 00nF (0, u) C : 00nF (0, u). IC sockets, Watch the position of the notch! R : K ( - - - B) R : K ( - - - B) R : K ( - - - B) R : K ( - - - B) R : K ( - - - B) R : 00K ( - 0 - - B) R : 00K ( - 0 - - B) R : 00K ( - 0 - - B) R9 : 0K ( - 0 - - B) VR : UA IC : P IC : P
Construction. Transistors. T : BC T : BC 0. Headers. Board to wire connector. Voltage regulator VR : UAL0 9. LEDs. Watch the polarity! LD : mm Green LD : mm Yellow LD : mm Yellow LD : mm Red VR... CATHODE COLOR=... LD... SK : 0P SK : 0P. DC - Jack SK : VDC (Power) SK : poles SK : poles. Electrolytic Capacitor. Watch the polarity! C : 0µ F C : 0µ F C : µ F C : µ F C : µ F C9 : µ F C0 : 0µ F C...
Construction. Sub D - connector. IC s. Watch the position of the notch! SK : RS (9p female). ZIF socket IC : MAX IC : CD09. Rubber feet Mount the rubber feet on the solder side of the PCB, see fig.0. SK : 0p FIG.0 9
Construction. Serial cable Mount a SUBD connector on both sides of a shielded -core cable. Refer to fig..0 below. 9 SK SUBD 9-POLE MALE 9 SK SUBD 9-POLE FEMALE FIG.0. If you do not assemble cables with the included SUBD connectors, pay attention to the following: all conductors must be connected PIN to PIN. 0
Construction Now, mount a enclosure over each SUBD connector according to fig..0 FIG.0.
Software 9. PIC - selection cable Cut off a piece of each wire of the female 'board-to-wire' connector so there is cm of wire left on the connector. See fig..0 Cut off pieces of shrinkable tube with a lenght equal to cm. Slide the shrinkable tube over the wires of the female 'board to wire'-connector (fig..0) Solder each wire to a metal terminal Attention: Always make sure to slide down the shrinking tube far enough from the soldering points! Slide the shrinkable tube over the soldered joints and heat them using a hair dryer or, better still, using a paint stripper. cm FIG.0 FIG.0
Software installation 0. Software installation Place the Velleman software CD in your CD-ROM player. Select Browse through this CD for other Velleman software (this message will not be displayed on your screen if AUTORUN is not activated). Select the K0 folder. Run the SETUP.EXE program in the 'C:\K0\ folder. Follow the indications on the screen until all files are installed. For connecting, testing and using this kit please refer to the programme help file on the included CD.
Schematic diagram. Schematic diagram. SK + SW - V DC D N00 C0 0µ F/ D C 00n VR UA I O D N C 00n C 0µ F VR UAL0 I O C 00n R0 FB C 0µ F +VPP +V +VPIC +VPIC R K N +V +VPIC ICF CD09B VCC VSS SK ICSP LD PG. SK ICSP ICB SUBD9-P - IBM SERIAL INTERFACE SK 9 C µ Fµ VCC V+ C+ C V- C- µ C+ C- TOUT TIN TOUT TIN 0 RIN ROUT RIN ROUT 9 IC MAXN C µ Fµ C9 µ Fµ 9 ICD 0 ICE ICC ICA R K LD R K LD SK 9 0 9 0 0 9 9 0 0 9 9 0 PIC 0PIN HEADER 0P ZIF-SOCKET SK 0 9 0 9 0PIN HEADER +VPP +VPP R9 0K R 00K T R BCC T K R BCC FB0 R R 00K D K N R 00K LD DVPP DPGD DPGC ICSP CONNECTORS VPP +VPIC (V) PGM DATA (PGD) PGM CLOCK (PGC)
PCB. PCB
VELLEMAN Components NV Legen Heirweg 990 Gavere Belgium Europe www.velleman.be www.velleman-kit.com Modifications and typographical errors reserved Velleman Components nv. H0IP' - 00 09