Measuring and monitoring units VAMP 96 VAMP 260 WIMO 6CP10

Transcription

1 Measuring and monitoring units VAMP 96

2 Measuring and monitoring units Main characteristics Intelligent measuring and monitoring units The VAMP and WIMO meters come with an extensive selection of pre-configured data screens and measurements that you can use or customize to fit your metering requirements. Cost Allocation and Billing Determine consumed energy by production cost centers according to the EU s Energy Service Directive (ESD) 2006/2/EC. Demand and Power Factor Control Avoid penalties with automated load shedding, scheduling, peak shaving or capacitor bank control Equipment Monitoring and Control Improve process yields and extend equipment life. Extensive analog and digital I/O enables system monitoring and control. Power quality and Disturbance Analysis Capturing abnormal disturbances in power quality like harmonics, voltage interruptions, voltage sags/swells and unbalancing. Preventative Maintenance Set up alarms to warn of pending problems in advance Extensive communication and SCADA connectivity IEC 61850, IEC , IEC , Modbus TCP, Profibus DP, DNP.0, DNP TCP, SPA, MBus (VAMP 96) Remote or stand-alone monitoring of industrial and utility substations VAMP 96 and for industrial and utility applications VAMP 96 and metering devices are designed for industrial and utility applications where energy consumption and billing shall be monitored by cost centers or individual feeder. Demand and power factor control, equip-ment monitoring, alarms for preventive maintenance and disturbance capturing are standard features in VAMP 96 and. As a member of VAMP protection relay family these meters come with an extensive communication capabilities. for utility applications meters are optimized for the utility applications suitable for secondary power distribution substations. The load monitoring and fault detection on the power distribution network is very important part of the real time maintenance and fault tracking sequences. Distribution transformers have been installed without supervision or with stand-alone metering in the past. meters can also be stand-alone but with optional communication facilities these devices can be connected to network control centers for continuous supervision 2

3 A right product for every application Solution VAMP 96 Operational segment Industrial and Industrial and Utility secondary utility substations utility substations power distribution Application Power, energy, Power, energy, Power, energy and power quality metering, power quality metering, power quality metering, event handling and event handling, earth fault detection, I/O unit for SCADA and control, alarming, alarming, process automation temperature monitoring and temperature monitoring, I/O unit for SCADA and process automation alarm and load profile SCADA transfer over GSM, GPRS CT and VT input Metering core Metering or Metering core connection protection core Auxiliary supply range V ac 18 6 V dc V ac V dc or V dc or V dc / ac V dc Number of digital inputs 6 Number of RTD inputs - Optionally Number of heavy trip contacts Number of alarm contacts Number of ma outputs Number of solid state outputs 1 pc NO 1 pc NO / NC

4 Measuring and monitoring units Product Overview VAMP 96 measuring and monitoring unit The VAMP 96 is a modern basic multimeter used as a stand alone meter in industrial low and medium voltage power distribution distribution panels. This meter can be connected to SCADA or energy management system in order to provide required measurements, alarms, condition data, events to the operator using various communication protocols. VAMP 96 shall be connected to measurement core of the current and voltage transformers Typical application of VAMP 96 is to measure energy by production cost centers and to show energy savings. VAMP 96 is a basic multimeter used either stand-alone or part of monitoring / SCADA system power monitoring unit The is designed for a heavy duty industrial applications where the environmental and disturbance conditions are demanding. This power monitoring unit can be connected to the protection cores of the current and voltage transformers as the design of the unit is equal to the requirements used in protection relays. Having six digital inputs, two circuit breaker controlling, four alarming duty contacts and four analogue ( ma ) outputs this unit is unique in the market. measuring and monitoring unit The is optimized for the utility applications especially for the secondary power distribution substations. The secondary power distribution transformers can now be monitored either stand alone or remotely using various communication protocols and channels. The distribution transformer stations located either in the rural area or basements of the houses can be taken cost effectively to the continuous monitoring from the electrical, water or transformer oil level, temperature, door switch, ventilation, burglar, graffiti spraying detection point of view to name a few typical monitored quantities. is a unique high accurate meter as it can be connected to either protection or measurement core of the current transformers. is used either stand-alone or it is connected to the supervision system of the utility s secondary power distribution network. 4

5 VAMPSET setting and configuration tool VAMPSET is a user-friendly, free-of-charge relay management software for setting, parameterising and configuring of VAMP relays. Via the VAMPSET software relay parameters, configurations and recorded relay data can be swapped between the operator s PC and the VAMP relays. Supporting the COMTRADE format VAMPSET also incorporates tools for analyzing relay events, waveforms and trends from data recorded by the relays, e.g. during a network fault situation. Using a standard RS cable the PC running VAMPSET connects to the front or rear port of the VAMP / WIMO devices. The VAMPSET software also supports TCP/IP communication via an optional 10Base-T connection. Featuring true multi-language support the software runs on Windows 7/Vista / XP / 2000 / NT / 98 / 95 without any need for configuration of the PC. The VAMPSET software is future-safe supporting coming updates and new VAMP products. The VAMPSET software size is about 1 Mbytes; you may conveniently distribute it by saving valuable transport and waiting time and money. Measurement view in VAMPSET of unit. A disturbance recorder view from indicating a faulty cable termination from the incoming feeder of paper mill s supply. This recording gave pre-information hence the repair action was possible before the cable termination faulted. VAMPSET shows on-line the content of voltage and current distortion from each phase measured by the VAMP and WIMO meters. Measured and calculated values come straight from the databases of the VAMP and WIMO meters. As a regular feature of the VAMP and WIMO units, standard COMTRADE type disturbance recording files can be uploaded for subsequent evaluation of any network event recorded. 5

6 Measuring and monitoring units Functionality 6

7 Communication Various communication alternatives to our demand As VAMP 96 and are members of VAMP protection relay family the meters benefit of the communication protocols widely used in other VAMP devices. The metering and control devices are often interfaced with Profibus DP, MODBUS TCP, Modbus RTU or SPA communication in industrial applications. Utilities request IEC 61850, IEC , IEC , DNP.0 and SPA protocols. In addition to this, the VAMP 96 has a MBus protocol in order to support connectivity with the Automatic Meter Management (AMM) systems. WIMO s connectivity to SCADA The WIMO s SCADA connection solution allows monitoring of the secondary substations over the internet. An ASP contract makes the commissioning of the WIMO fast and easy as the users of the system does not require any hardware at Network Control Center (NCC) side. Ready-made event, alarm, setting and measurement views are informative and the system enables transfer of data for instance to Word, Excel, html and txt format for further analysis. SCADA, DCS or SA system Maintenance Terminal Control and status of the process Events Measurements Fault location Time synchronizing using GPS Relay settings, configuration Fault and disturbance analysis Power quality monitoring Primary equipment condition monitoring Time synchronizing using GPS * IEC , IEC ,Modbus RTU, Modbus TCP, Profibus, SPA, DNP.0, DNP TCP or IEC Physical Media: RS 485 RS 22 Fibre optic Ethernet TCP / IP, RS 485 or fibre OPC client WIMO s SCADA connection OPC server OPC client RMU Secondary Substation MV/LV SCADA LAN (TCP/IP) RMU Secondary Substation MV/LV GSM/GPRS modem RMU Secondary Substation MV/LV Cost effective communication media The most efficient communication media from the secondary substations are GMS, GPRS, leased modem line or fiber optical communication. Using the WIMO-GSM communication only three messages a day is required to transfer all measurements to Network Control Center. Leased modem line or GPRS allows real time data transfer cost efficiently. GSM/GPRS modem Measuring and Monitoring Unit GSM/GPRS modem Measuring and Monitoring Unit GSM/GPRS modem Measuring and Monitoring Unit 7

8 Measuring and monitoring units Connection diagrams L1 L2 L connection diagram P 2 AO 1 AO 2 AO AO 4 P 1 X X X is connected to phase voltages in a 400 V network is connected to line voltages in a 400 V network 8

9 10kV VAMP 96 connection diagram R 10/0.4kV X2B:1 X2B:2 Uaux ~ VAMP 96 Measurement functions Local X4 X2A:2 N Remote X2A:5 X2A:4 U1 U2 V A Hz X X2A: U N L1 L2 L VA W var P.F cosfii tanfii X1:1 X1:2 X1: X1:4 X1:5 X1:6 IL1 IL2 IL Wh varh THD U&I harmonics Relay out General digital inputs X2B: DI1 X2B:4 DI2 X2B:5 DI X2B:8 +12V DI X2A:7 X2A:8 Energy pulse output VAMP96_LVCON_2 I 0 connection diagram o C X2A:1 Uaux ~ Local X4 Measurement functions X2A:2 N Remote X2A:5 X2A:4 U1 U2 ~ ~ V A Hz X X2A: U PEN L1 L2 L X2B:1 X2B:2 Io VA W var P.F cosfii tanfii X1:1 X1:2 IL1 Wh varh THD X1: X1:4 IL2 X1:5 X1:6 IL U&I harmonics X2B: DI1 X2B:4 DI2 X2B:5 DI DI Relay out X2A:8 X2A:9 X2A:7 X2B:8 +12V PT100 X2B:6 X2B:9 X2B:7 WIMO6CP10_WIRECON_2 + - VOLTAGE SUPPLY TO GSM 9

10 Measuring and monitoring units Typical applications Wimo 6CP10 is optimal metering and monitoring unit for utility s secondary power distribution substations I 0 Remote Control Center VAMP 96 VAMP 96 is a basic metering and control device used for measuring power and energy of production cost centers in industrial applications. The same meter can be used by the utilities for detecting consumed energy per feeder. 110/10kV Energy Management System 10kV 20/0.4kV o C Modbus, Profibus DP, TCP/IP I U ALARMS I U Vamp96 I U Vamp96 VAMP 96 VAMP 96 10/0.4kV 10/0.4kV power monitoring unit applied for monitoring of power and energy at industrial power distribution. Energy pulses drive Energy Management System whereas the alarms and load information goes via the serial communication to the Control Center. The ma outputs control analogue meters of the switchgear. Remote Control Center Energy Management System Serial communication Energy pulses 10

11 Order codes Accessories VAMP 96 1 C 7 Nominal current [A] 1 = 5 A Nominal Voltage [V] C = V Frequency [Hz] 7 = 50/60 Hz Supply voltage [V] A = Vac/dc B = Vdc G = Vdc Optional hardware A = None O = LC 100 Mbps interface inc. IEC and M-bus P = RJ Mbps ethernet interface inc. IEC and M-bus Optional hardware A = Version 6 firmware** B = Note: (** Only optional hardware, A available 1 C 7 A Nominal current [A] 1 = 1 A Nominal Voltage [V] C = V Frequency [Hz] 7 = 50/60 Hz Supply voltage [V] A = Vac/dc Optional hardware A = None O = LC 100 Mbps interface inc. IEC and M-bus P = RJ Mbps ethernet interface inc. IEC and M-bus Optional hardware A = B = Nominal current [A] 1 = 1 A 5 = 5 A Nominal Voltage [V] C = V Frequency [Hz] 7 = Standard relay Supply voltage [V] A = Vac/dc B = Vdc Optional hardware (communication port 1) A = None B = C = D = RS 485 interface (4-wire) E = F = G = H = RJ-45 10Mbps ethernet interface M = RJ-45 10Mbps ethernet inc. IEC O = LC interface inc. IEC P = RJ Mbps ethernet interface inc. IEC R = interface inc. IEC S = 2 x RJ Mbps ethernet interface inc. IEC A = # B = # C = D = E = F = Note: ( * Optional hardware, A-H available (# Optional hardware, A-G available Order code Description Note VEA CGi External Ethernet Interface Module VPA CG VSE001 Fiber optic Interface Module VSE002 RS485 Interface Module VSE00 RS485 Interface Module, Ext I/O interface VSE004 RS485 Interface Module, Ext I/O interface VSE009 External DeviceNet interface module VIO 12 AB RTD Module, 12pcs RTD inputs, RS 485 Communication (24-20 Vac/dc) VIO 12 AC RTD/mA Module, 12pcs RTD inputs, PTC, ma inputs/outputs, RS22, RS485 and Optical Tx/Rx Communication (24 Vdc) VIO 12 AD RTD/mA Module, 12pcs RTD inputs, PTC, ma inputs/outputs, RS22, RS485 and Optical Tx/Rx Communication (48-20 Vac/dc) VX00- RS22 programming cable (Vampset, VEA CGi) Cable length m VX028- Cable length m VX02- Back panel programming cable Cable length m VX00- Interface cable to VEA CGi (Ethernet module) Cable length m VX004-M TTL/RS22 converter cable (PLC, VEA CGi) Cable length m VX007-F TTL/RS22 converter cable (VPA CG) Cable length m VAM 16D External LED module Disables rear local communic sensor Earth-fault current sensor Cabletroll WIMOTEMP Pt100 Pt100 sensor Cable length 5 m sensor Short-circuit sensor Horstman VYX076 Raising Frame for 200-serie Height 40 mm VYX077 Raising Frame for 200-serie Height 60 mm VYX2 Raising Frame for 200-serie Height 100 mm V200WAF V200 wall assembly frame VAMP 96 11

12 Measuring and monitoring units Dimensional drawings All dimensions in mm. power monitoring unit Semi-flush mounting b a Panel mounting Depth with raising frames Type designation a b VYX mm 169 mm VYX mm 149 mm VYX mm 109 mm 19.0 > PANEL CUT-OUT 12

13 VAMP 96 and measuring and monitoring units Measuring and Monitoring Unit X 96,0 ALARM POWER C E 90,0 96,0 96,0 X X2A VY091 90, X2B 88,0 96,0 107,0 TOP 89,0 mm 91,0 mm VY101C 96,0 107,0 Panel cut-out 18,0 12,5 150,5 9,0 Connection label VAMP 96 L1 L2 L N PULSE OUT L1 L2 L PEN RELAY OUT NO / NC X2A X2A X1 X2B X1 X2B U BINARY INPUTS I 0 BINARY INPUTS PT100 VOLTAGE SUPPLY TO GSM VY108B 1

14 Measuring and monitoring units Technical data, tests and environmental conditions Measuring circuitry VAMP 96 Rated current In 1 A or 5 A 1 A or 5 A 1 A or 5 A - Current measuring range 1 x In 0-5 x In 0 1 x In - Thermal withstand 1,2 x In (continuously) 4 x In (continuously) 1,2 x In (continuously) 20 x In (for 10 s) 100 x In (for 1 s) - Burden < 0.1 VA (In = 1 A) < 0.1 VA (In = 1 A) < 0.1 VA (In = 1 A) < 0.2 VA (In = 5 A) < 0.2 VA (In = 5 A) < 0.2 VA (In = 5 A) Rated voltage Un V V (configurable) 20 V - Voltage measuring range V V V - Continuous voltage withstand 264 V 275 V 275 V - Burden < 0.5V A < 0.5V A < 0.5V A Rated frequency fn Hz Hz Hz - Frequency measuring range Hz Hz Hz Terminal Block: Max. wire dimension: Max. wire dimension: Max. wire dimension: - Solid or stranded wire 2,5 mm 2 (1-14 AWG) 4 mm 2 (10-12 AWG) 2,5 mm 2 (1-14 AWG) Auxiliary voltage Type A (standard) Type B (option) Type A (standard) Type B (option) Rated voltage Uaux V ac/dc V dc V ac/dc 18-6 V dc V ac/dc 110/120/220/240 V ac/dc 24 V dc 110/120/220/240 V ac/dc 24 V dc 110/120/220/240 V ac/dc V dc 48/60/110/125/220 V V dc dc Power consumption 5 W (normal conditions) < 7 W (normal conditions) 5 W (normal conditions) < 15 W (output relays activated) Max. permitted interruption time < 50 ms (110 V dc) Terminal Block: Max. wire dimension: Max. wire dimension: Max. wire dimension: - Phoenix MVSTBW or equivalent 2.5 mm 2 (1-14 AWG) 2.5 mm 2 (1-14 AWG) 2.5 mm 2 (1-14 AWG) Digital inputs Number of inputs 6 Operation time s (step 0.01 s) s (step 0.01 s) s (step 0.01 s) Polarity NO (normal open) or NC (normal closed) NO (normal open) or NC (normal closed) NO (normal open) or NC (normal closed) Inaccuracy: - Operate time ±1% ±1% ±1% Internal operating voltage 12 V dc 48 V dc 12 V dc Current drain when active (max.) Approx. 5 ma Approx. 20 ma Approx. 5 ma Current drain, average value < 1 ma Terminal block: Max. wire dimension: Max. wire dimension: Max. wire dimension: - Phoenix MVSTBW or equivalent 2.5 mm 2 (1-14 AWG) 2.5 mm 2 (1-14 AWG) 2.5 mm 2 (1-14 AWG) Trip contacts Number of contacts - 2 making contacts - Rated voltage V ac/dc - Continuous carry - 5 A - Max. making current - 15 A - Breaking capacity, AC VA - Breaking capacity, DC (L/R=40ms) - 50 W - Contact material - AgNi 90/10 - Terminal Block: Max. wire dimension: - Phoenix MVSTBW or equivalent mm 2 (1-14 AWG) - Accuracy Current +/- 0.4 % of value when I > 0.5 x In +/- 0. % of In +/- 0.4 % of value when I > 0.5 x In Voltage +/- 0.5 % of value +/- 0.5 % +/- 0.5 % of value Frequency: +/- 10 mhz +/- 10 mhz +/- 10 mhz Active power +/- 1 % of value +/- 1 % of value +/- 1 % of value Reactive power +/- 1 % of value +/- 1 % of value +/- 1 % of value Active energy +/- 1 % of value +/- 1 % of value +/- 1 % of value Reactive energy +/- 1 % of value +/- 1 % of value +/- 1 % of value 14

15 Alarm contacts VAMP 96 Number of contacts 1 normally open change-over contacts 1 change-over contact (A1) (relays A1, A2 and A) 1 change-over contact (IF relay) Rated voltage 48 V ac/dc 250 V ac/dc 48 V ac/dc Max. make current 120 ma 15 A N.O. 10 A / N.C. A Continuous carry A 5 A A Breaking capacity, AC VA N.O VA / N.C. 500 VA Contact material - AgNi 0.15 goldplated AgAl 0.15 goldplated Terminal Block: Max. wire dimension: Max. wire dimension: Max. wire dimension: - Phoenix MVSTBW or equivalent 2.5 mm 2 (1-14 AWG) 2.5 mm 2 (1-14 AWG) 2.5 mm 2 (1-14 AWG) Local serial communication port Number of ports 1 on front and 1 shared 1 on front and 1 on rear panel 1 on front and 1 shared with remote on rear panel with remote on rear panel Electrical connection RS 22 RS 22 RS 22 Data transfer rate kb/s kb/s kb/s Remote control connection Number of ports 1 shared with local port on rear panel 1 on rear panel 1 shared with local port on rear panel Electrical connection RS 22 (standard) TTL (standard) RS 22 (standard) TTL RS 485 (option) TTL RS 485 (with external module) RS 22 (option) RS 485 (with external module) Plastic fibre connection (with ext. module) Plastic fibre connection (option) Plastic fibre connection (with ext. module) Data transfer rate kb/s kb/s kb/s Protocols ModBus RTU master ModBus RTU master GSM ModBus / TCP ModBus / TCP GPRS SpaBus, slave SpaBus, slave SpaBus, slave IEC IEC IEC IEC IEC IEC IEC IEC IEC Profibus DP (option) Profibus DP (option) Profibus DP (option) MBus MBus TCP/IP (option) DNP or Ethernet DNP or Ethernet DNP.0 Analogue outputs Number of Ports - 4 (Note: common +pole) - Electrical connection: - Current output - - Range ma (min & max configurable) - - Load - <800 W - - Accuracy - <±20mA - Isolation test voltage Vdc - Test voltages Insulation test voltage 2 kv, 50 Hz, 1 min 2 kv, 50 Hz, 1 min 2 kv, 50 Hz, 1 min (IEC ) Surge voltage (IEC ) 5 kv, 1.2/50 ms, 0.5 J 5 kv, 1.2/50 ms, 0.5 J 5 kv, 1.2/50 ms, 0.5 J Environmental conditions Operating temperature -25 to +50 o C -10 to +55 o C -25 to +50 o C Operating temperature (display) 0 to +50 o C 0 to +50 o C Transport and storage temperature -10 to +60 o C -40 to +70 o C -10 to +60 o C Relative humidity < 75 % (1 year, average value) < 75% (1 year, average value) < 75% (1 year, average value) < 90 % (0 days per year, < 90% (0 days per year, < 90% (0 days per year, no condensation permitted) no condensation permitted) no condensation permitted) Casing Degree of protection (IEC 60529) IP20 IP20 / Flush mounted IP54 IP20 Dimensions (W x H x D) 96 x 96 x 151 mm 208 x 155 x 26 mm 96 x 96 x 151 mm Material Polyphenylene Oxide 1 mm steel plate Polyphenylene Oxide Weight 0.6 kg 4.2 kg 0.6 kg Color code RAL 702 (Casing)/RAL 705 (Back plate) Package Dimensions (W x H x D) 180 x 100 x 101 mm 215 x 160 x 275 mm 180 x 100 x 101 mm Weight (relay, package and manual) 0.7 kg 5.2 kg 0.7 kg 15

16 With its headquarters in Finland, Vamp Ltd specialises in protection relays, arc flash protection and measuring and monitoring units for power systems. Vamp s medium-voltage and sub-transmission protection relays are used in a number of applications, from overhead line feeders and substations to power plants and industrial power system. Their unique integrated arc flash fault protection functionality enhances the safety of both people and property and has made Vamp a leading brand in arc flash protection worldwide. Vamp is a member of Schneider Electric, a global specialist in energy management. Our success is based on competitive standard products, constant development by our designers possessing experience from three protection relay generations, our long-term partnerships, flexibility and 24 hour care of the customers. Our organization has been audited and found to be in accordance with the requirements of the ISO 9001 management system. Vamp Ltd P.O.Box 810 FI VAASA Finland Visiting address: Vaasa Airport Park Yrittäjänkatu 15 Vaasa, Finland We reserve the rights to product alterations without prior notice. Copyright Vamp Ltd. All trademarks are the property of their respective holders. Tel: Fax: [email protected] VB260.EN007 06/2012