Tel: (949) SECI Engineers & Buyers' Guide Fax: (949)
|
|
- Virginia Bruce
- 7 years ago
- Views:
Transcription
1 Sharma Resistors Page 1 Quick Reference Series Features Page CR Chip Type Case Sizes 2 RS Carbon Composition 1/2 Watt 4
2 Sharma Resistors Page 2 CR THICK FILM CHIP RESISTOR SERIES INTRODUCTION The most popular type of chip resistor developed for surface mount technology. Ideal for general purpose applications. Unique construction and special termination techniques ensure high quality and reliability. Extremely compact size for miniaturization. FEATURES Excellent Long Term stability Available in Bulk and Tape & Reel packing. Available in Tolerances of ±5% & ±1% Uniform body size ensures compatibility with High Speed automatic handling machines Compatible with flow and re-flow soldering methods SPECIFICATIONS Resistance Range: 1 Ohm to 10 M Ohms for E24 values(5%) 1 Ohm to 1 M Ohms for E96 values(1%) Rated Power: 1/16 to 1W at 70 C (Please see Power Derating Curve) Rated Voltage: Rated Power x Nominal Resistance. Overload Voltage: Please refer to Power Ratings Table. Temperature Coefficient: ± 100 ppm or ± 200 ppm per C. Temperature Range: -55 C to +125 C with derating above 70 C Tolerance: ± 5% or ±1% (Special tolerance upon request.). Load Life: The component will be subjected to 1000 hours of testing at rated voltage and 70 C, with duty cycles of 1.5 hours ''on'' and 0.5 hours ''off''. After the test the Resistance change will remain within ±3% of the initial value Ohm for values above 1 M Ohm and 5% for values less than 1 M Ohm. Resistance to Soldering Heat: The component can be subjected to a soldering temperature of 270 C for 10 seconds. After the test the Resistance change will remain within ±3% Ohms. Case Dimensions Table Dimensions in mm Case Code L W T Max e Power Derating Curve Tape, Reel and Packing Specifications Reel Dimensions; Reel Dimensions in Millimeters A B C D E W t ø178 ±2.0 ø50 min ± ± ± /12.8 ± ±0.5 ø330 ±2.0 ø100 min ± ± ± /12.8 ± ±0.6 Reel Dimensions in Inches A B C D E W t ø7 ±0.08 ø2.0 min. 5.0 ± ± ± /0.50 ± ±0.02 ø13 ±0.08 ø4.0 min. 5.0 ± ± ± /0.50 ± ±0.02 Power Ratings Table (Values above 10 M Ohms are available upon request) SIZE Rate Power Rate Current Maximum Maximum Temperature Combination of Resistance Operating at 70C of Jumper Working Overload Coefficient Range of Tolerance Temperature A Voltage Voltage of Resistance F (+1%) J (+ 5%) Range C Vw Vo ppm/c (E96) (E24) / Ohms-562 K Ohms Ohm-9.76 Ohms 10 Ohms - 1 M Ohms / Ohms-1 M Ohms Ohm Ohms 1 Ohm- 10 M Ohms / Ohms - 1 M Ohms Ohm Ohms 1 Ohm - 10 M Ohms / Ohms-1 M Ohms Ohm Ohms 1 Ohm - 10 M Ohms / Ohms - 1 M Ohms Ohm Ohms 1 Ohm - 10 M Ohms Ohms - 1 M Ohms Ohm Ohms 1 Ohm - 10 M Ohms
3 Sharma Resistors Page 3 Carrier Tape Dimensions; φ ± 0.1 ± 0.1 E F W B Tmax A P A B W F E P Tmax SIZE ±0.2 mm or ±0.2 mm or ±0.3 mm or ±0.1 mm or ±0.1 mm or ±0.1 mm or CODE ±0.008'' ±0.008'' ±0.012'' ±0.004'' ±0.004'' ±0.004'' (0.026") 1.15 (0.045") 8.0mm (0.315") 3.5mm (0.138") 1.75mm (0.069") 2mm (0.079") 0.43mm (0.018") (0.043") 1.9mm (0.075") 8.0mm (0.315") 3.5mm (0.138") 1.75mm (0.069") 4mm (0.157") 0.60mm (0.024") (0.065") 2.4mm (0.094") 8.0mm (0.315") 3.5mm (0.138") 1.75mm (0.069") 4mm (0.157") 0.75mm (0.030") (0.075") 3.5mm (0.138") 8.0mm (0.315") 3.5mm (0.138") 1.75mm (0.069") 4mm (0.157") 0.75mm (0.030") (0.011") 5.6mm (0.22") 12.0mm (0.472") 5.5mm (0.217") 1.75mm (0.069") 4mm (0.157") 0.20mm (0.080") (0.142") 6.7mm (0.264") 12.0mm (0.472") 5.5mm (0.217") 1.75mm (0.069") 8mm (0.315") 0.20mm (0.080") Packing Methods; PACKING Paper Taping Reel (R) Embossed Taping Reel (K) Bulk Cassette (K) Style 7" (178mm) 10" (254mm) 13" (330mm) 7" (178mm) CR02 (0402) 10,000 10,000 10,000-50,000 CR03 (0603) 5,000 5,000 5,000-25,000 CR05 (0805) 5,000 5,000 5,000-10,000 CR06 (1206) 5,000 5,000 5,000-5,000 CR20 (2010) ,000 - CR25 (2512) ,000 - EIA Code-E24 Values EIA Code-E96 Values PART NUMBERING CR Packaging: Series: 1 = 5K Paper Taping = or 4 Digit 2 = 10K Paper Taping 03 = 0603 EIA Code. 3 = 20K Paper Taping = = 4K Plastic Taping = 1206 Tolerance: Circuits: 5 = Loose Packing = 2010 F = + 1% 0 = NA A = 5K Cassette 25 = 2512 G = + 2% B = 10K Cassette J = + 5% C = 25K Cassette D = 50K Cassette Temp. Coefficient: Add 3 digit multipler = ppm/c Examples: = ppm/c 101= 100 Ohms = 4.7K Ohms = 680K Ohms Add 4 digit multipler 1R0= 1 Ohm Examples: 15R= 15 Ohms 1130= 113 Ohms 1871= 1.87K Ohms Note: 6193= 619K Ohms R= decimal point in 19R1= 19.1 Ohms Tel: (949) the EIA code 1R21= 1.21 Ohms SECI Engineers & Buyers' Guide Fax: (949)
4 Sharma Resistors Page 4 THE FIXED CARBON COMPOSITION RESISTORS 1. Dimensions d W L W D 2. Rating and Dimensions Dimensions in mm Rated Power Type (W) L D W d Max Rated Voltage v Max Overload Voltage v Resistance range RS11-1/ to 22M 3. Sold Resistance in Packs 1/2WATT SHARMA Type # SHARMA Type # SHARMAType # SHARMA Type # RS11-1/2W-4R7 4.7 RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W-5R1 5.1 RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W5R6 5.6 RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W-6R2 6.2 RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W-6R8 6.8 RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W-7R5 7.5 RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W-8R2 8.2 RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W-9R1 9.1 RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W RS11-1/2W-1K 1.0K
5 Sharma Resistors Page 5 1/2WATT Cont. SHEET:1 OF 6 SHARMAType# SHARMA Type # SHARMA Type # SHARMA Type # RS11-1/2W-1K1 1.1K RS11-1/2W-13K 13K RS11-1/2W-160K 160K RS11-1/2W-2M 2.0M RS11-1/2W-1K2 1.2K RS11-1/2W-15K 15K RS11-1/2W-180K 180K RS11-1/2W-2M2 2.2M RS11-1/2W-1K3 1.3K RS11-1/2W-16K 16K RS11-1/2W-200K 200K RS11-1/2W-2M4 2.4M RS11-1/2W-1K5 1.5K RS11-1/2W-18K 18K RS11-1/2W-220K 220K RS11-1/2W-2M7 2.7M RS11-1/2W-1K6 1.6K RS11-1/2W-20K 20K RS11-1/2W-240K 240K RS11-1/2W-3M0 3.0M RS11-1/2W-1K8 1.8K RS11-1/2W-22K 22K RS11-1/2W-270K 270K RS11-1/2W-3M3 3.3M RS11-1/2W-2K 2.0K RS11-1/2W-24K 24K RS11-1/2W-300K 300K RS11-1/2W-3M6 3.6M RS11-1/2W-2K2 2.2K RS11-1/2W-27K 27K RS11-1/2W-330K 330K RS11-1/2W-3M9 3.9M RS11-1/2W-2K4 2.4K RS11-1/2W-30K 30K RS11-1/2W-360K 360K RS11-1/2W-4M3 4.3M RS11-1/2W-2K7 2.7K RS11-1/2W-33K 33K RS11-1/2W-390K 390K RS11-1/2W-4M7 4.7M RS11-1/2W-3K 3.0K RS11-1/2W-36K 36K RS11-1/2W-430K 430K RS11-1/2W-5M1 5.1M RS11-1/2W-3K3 3.3K RS11-1/2W-39K 39K RS11-1/2W-470K 470K RS11-1/2W-5M6 5.6M RS11-1/2W-3K6 3.6K RS11-1/2W-43K 43K RS11-1/2W-510K 510K RS11-1/2W-6M2 6.2M RS11-1/2W-3K9 3.9K RS11-1/2W-47K 47K RS11-1/2W-560K 560K RS11-1/2W-6M8 6.8M RS11-1/2W-4K3 4.3K RS11-1/2W-51K 51K RS11-1/2W-620K 620K RS11-1/2W-7M5 7.5M RS11-1/2W-4K7 4.7K RS11-1/2W-56K 56K RS11-1/2W-680K 680K RS11-1/2W-8M2 8.2M RS11-1/2W-5K1 5.1K RS11-1/2W-62K 62K RS11-1/2W-750K 750K RS11-1/2W-9M1 9.1M RS11-1/2W-5K6 5.6K RS11-1/2W-68K 68K RS11-1/2W-820K 820K RS11-1/2W-10M 10M RS11-1/2W-6K2 6.2K RS11-1/2W-75K 75K RS11-1/2W-910K 910K RS11-1/2W-11M 11M RS11-1/2W-6K8 6.8K RS11-1/2W-82K 82K RS11-1/2W-1M 1.0M RS11-1/2W-12M 12M RS11-1/2W-7K5 7.5K RS11-1/2W-91K 91K RS11-1/2W-1M1 1.1M RS11-1/2W-13M 13M RS11-1/2W-8K2 8.2K RS11-1/2W-100K 100K RS11-1/2W-1M2 1.2M RS11-1/2W-15M 15M RS11-1/2W-9K1 9.1K RS11-1/2W-110K 110K RS11-1/2W-1M3 1.3M RS11-1/2W-16M 16M RS11-1/2W-10K 10K RS11-1/2W-120K 120K RS11-1/2W-1M5 1.5M RS11-1/2W-18M 18M RS11-1/2W-11K 11K RS11-1/2W-130K 130K RS11-1/2W-1M6 1.6M RS11-1/2W-20M 20M RS11-1/2W-12K 12K RS11-1/2W-150K 150K RS11-1/2W-1M8 1.8M RS11-1/2W-22M 22M 4. Part Numbering System Example: RS11 1/2W 2k7 J T type Rated Power W Normal Resistance Resistance Tolerance Packaging RS11 0.5W 2k7=2.7k J = 5% K= 10% M= 20% B T Bulk Tape &Reel
6 Sharma Resistors Page 6 5. Derating Curve Rated Load P / P R % Temperature 6. Resistance Temperature Characteristics Max. Resistance Characteristics Resistance range ( R*/R)% Temperature range Temperature range -55 to to k and under k to 10k k to 100k k to 1M M to 10M M and over * R=R 2 -R 1 R 1 Resistance value at reference temperature Resistance value at test temperature R 2 7. Mechanical and Electronic Performance Description Test method Performance Requirements Frequency range: 10HZ ~ 500Hz No visible damage Vibration Amplitude: 0.75mm Total last tine: 6h R 2%R+0.1.
7 Sharma Resistors Page 7 8. Mechanical and Electronic Performance Cont. Description Test method Performance Requirements Pull Along the longitudinal axis of the terminal leads 20N, 5S Terminal Strength Bending two times Once in each No visible damage Bending direction R 2%R+0.1. Twist Twist 180 two times Resistance to Soldering Heat Solder temperature: Immerge time : S Depth from the body of the resistor: mm No visible damage R 2%R+0.1. Solderability Solder temperature : Dwell time in solder: 3 0.5S Depth from the body of the sesistor: mm At least 95% of the dipping surface must be covered by new solder no flaws gathered Voltage Coefficient (Application in 1K to 10M ) Use 10%Resistance rated voltage and 100%Resistance rated voltage to test resistance value A total resistance change of 2% max. or 0.035%/V Short time overload 2.5 times of rated voltage or times of Max. rated voltage (selecting lower ) 5S. No visible damage R 2%R+0.1 Dielectric withstanding voltage Resistois shall be clamped in the trough of a 90 metallic V-block and shall be tested at AC potential respectively Specified in the above list for 60 5s No evidence of arcing or insulation breakdown
8 Sharma Resistors Page 8 9. Mechanical and Electronic Performance Cont. Description Test method Performance Requirements A -55 Temperature fast B +125 No visible damage change Shape check Resistance R 2%R+0.1. Last out time : 1000h When 48h 500h and 1000h check: 70 endurance Shape check resistance When 1000h check: Insulation Resistance No visible damage Mark clarity R 10%R+0.5 R 1G Fixing state Damp heat Shape check Resistance Insulation Resistance No visible damage Mark clarity R 10%R+0.5 R 100M 10. Taping production Length from the end 2.0mm Tape Width T Lead Bending 0.8mm From Center 0.5mm Pitch P Lead Overlap 1.0mm Max L 1 L 2 Tape inner width W Tape overlap 1.0 e external width w
9 Sharma Resistors Page 9 Tape Style Taping Dimensions mm W A T P L1-L2 T SHEET 11. Products Package a. In bulk Description Specification Quantity Dimension (mm Length Width Height Thickness Small-size plastic bag 1/2 W 100 pieces ±0.005 Big-size plastic bag 1/2 W 5 bags ±0.005 Paper box 1/2 W 20 boxes Outside package 1/2 W 3 Paper boxes Note: Outside package weight 15±1 kg b. Taping Products Description Specification Quantity Dimension mm Length Width Height Thickness Paper box 1/2 W 2000 pieces Outside package 1/2 W 10 Paper boxes Note: Outside package weight 10±1 kg
DATA SHEET CHIP RESISTORS RT Series 1%; 0.5%; 0.25%; 0.1%
DATA SHEET CHIP RESISTORS Series 1%; 0.5%; 0.25%; 0.1% Product specification Supersedes Date of Sep. 30, 2003 ynsc004 ynsc015 ynsc002 ynsc007 2 SCOPE This specification describes series chip resistors
More informationWW12X, WW08X, WW06X, WW04X ±1%, ±5% Thick Film Low ohm chip resistors
WW12X, WW08X, WW06X, WW04X ±1%, ±5% Thick Film Low ohm chip resistors Size 1206, 0805, 0603, 0402 *Contents in this sheet are subject to change without prior notice. Page 1 of 8 ASC_WWxxX_V12 Nov.- 2011
More informationPulse Withstanding Thick Film Chip Resistor-SMDP Series. official distributor of
Product: Pulse Withstanding Thick Film Chip Resistor-SMDP Series Size: /// official distributor of Pulse Withstanding Thick Film Chip Resistor-SMDP Series 1. Scope -This specification applies to ~ sizes
More informationSMD High Power Precision Resistors
Key Features High precision - TCR 5ppm/ C and 10ppm/ C Tolerance down to 0.01% Thin film (nichrome) Choice of packages Stable high frequency performance Temperature range -55 C to +155 C Applications Communications
More informationHigh Power Thick Film Chip Resistor 2512
Specifications: Type : MCHP12 Power Rating at 70 C : 2W Working Voltage : 250V Max. Overload Voltage : 500V Max. Dielectric Withstanding Voltage : 500V Temperature Range : -55 C to +155 C Ambient Temperature
More informationType RP73 Series. SMD High Power Precision Resistors. Key Features. Applications. Characteristics - Electrical - RP73 Series - Standard
Key Features n High precision - tolerances down to 0.05% n Low TCR - down to 5ppm/ C n Stable high frequency performance n Operating temperature -55 C to +155 C n Increased power rating - up to 1.0W n
More informationStandard Thick Film Chip Resistors
Standard Thick Film Chip Resistors FEATURES Stability R/R = 1 % for 00 h at 70 C 2 mm pitch packaging option for size Pure tin solder contacts on Ni barrier layer provides compatibility with lead (Pb)-free
More informationTC50 High Precision Power Thin Film chip resistors (RoHS compliant Halogen Free) Size 1206, 0805, 0603
WF2Q, WF08Q, WF06Q ±%, ±0.5%, ±0.25%, ±0.%, ±0.05% TC50 High Precision Power Thin Film chip resistors (RoHS compliant Halogen Free) Size 206, 0805, 0603 *Contents in this sheet are subject to change without
More informationSIL Resistor Network. Resistors. Electrical. Environmental. L Series. Thick Film Low Profile SIP Conformal Coated Resistor Networks RoHS Compliant
Resistors SIL Resistor Network Thick Film Low Profile SIP Conformal Coated Resistor Networks RoHS Compliant All parts are Pb-free and comply with EU Directive 2011/65/EU (RoHS2) Electrical Standard Resistance
More informationSURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) Rotor. Wiper. Cover. Pin S T - 2 T A 1 0 0 Ω ( 1 0 1 )
SURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) COPAL ELECTRONICS RoHS compliant INTERNAL STRUCTURE 8 4 7! 5! 9 FEATURES RoHS compliant Compact and low-profile mm single turn type Sealed construction 4 5 7
More informationST-2 SURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) FEATURES PART NUMBER DESIGNATION S T - 2 T A 1 0 0 Ω ( 1 0 1 ) RoHS compliant
SURFACE MOUNT CERMET TRIMMERS (SINGLE TURN) ST- RoHS compliant INTERNAL STRUCTURE 8 4 7 FEATURES RoHS compliant Compact and low-profile mm single turn type Sealed construction 4 5 7 8 9!! 5 Part name Housing
More informationPower chip resistor size 2512 PRC221 5%; 2% FEATURES Reduced size of final equipment Low assembly costs Higher component and equipment reliability.
FEATURES Reduced size of final equipment Low assembly costs Higher component and equipment reliability. APPLICATIONS Power supplies Printers Computers Battery chargers Automotive Converters CD-ROM. QUICK
More informationSPECIFICATION FOR APPROVAL. Approved by
C O N F I D E N T I A L D O C U M E N T SPECIFICATION FOR APPROVAL CONRAD Description : Royalohm Part no.: 0402WGxxxxxTCE (RMC 1/16W (0402) +/- 1%, 5% & Jumper) 0603SAxxxxxT5E (RMC 1/10W-S (0603) +/- 1%,
More informationPulse Proof Thick Film Chip Resistors
Pulse Proof Thick Film Chip Resistors FEATURES High pulse performance, up to kw Stability R/R 1 % for h at 70 C AEC-Q200 qualified Material categorization: for definitions of compliance please see www.vishay.com/doc?99912
More informationMetal Film Resistors, Industrial, Precision
Metal Film Resistors, Industrial, Precision FEATURES Small size - conformal coated Flame retardant epoxy coating Controlled temperature coefficient Available Excellent high frequency characteristics Exceptionally
More informationWR12, WR08, WR06, WR04 ±1%, ±5% Thick Film General Purpose Chip Resistors Size 1206, 0805, 0603, 0402
WR12, WR08, WR06, WR04 ±1%, ±5% Thick Film General Purpose Chip Resistors Size 1206, 0805, 0603, 0402 *Contents in this sheet are subject to change without prior notice. Page 1 of 10 ASC_WR_V23 APR.- 2015
More informationPulse Proof, High Power Thick Film Chip Resistors
Pulse Proof, High Power Thick Film Chip Resistors STANDARD ELTRICAL SPIFICATIONS MODEL CASE SIZE INCH CASE SIZE METRIC POWER RATING P 70 W LIMITING ELEMENT VOLTAGE U max. AC/DC -HP e3 FTURES Excellent
More informationHigh-ohmic/high-voltage resistors
FEATURES High pulse loading capability Small size. APPLICATIONS Where high resistance, high stability and high reliability at high voltage are required High humidity environment White goods Power supplies.
More informationMetal Film Resistors, Industrial, Precision
CMF Industrial Metal Film Resistors, Industrial, Precision FEATURES Small size - conformal coated Flame retardant epoxy coating Controlled temperature coefficient Excellent high frequency characteristics
More informationHigh-ohmic/high-voltage resistors
FEATURES These resistors meet the safety requirements of: UL1676 (range 510 kω to 11 MΩ) EN60065 BS60065 (U.K.) NFC 92-130 (France) VDE 0860 (Germany) High pulse loading capability Small size. APPLICATIONS
More informationDATA SHEET LEAD FREE CHIP RESISTORS RC_P series ±0.5%, ±1%, ±5% Sizes 0100/0201/0402/0603/0805/ 1206/1210/1218/2010/2512
DATA SHEET LEAD FREE CHIP RESISTORS RC_P series ±0.5%, ±1%, ±5% Sizes 0100/0201/0402/0603/005/ 1206/1210/121/2010/2512 Product specification August 22, 2014 V.0 Product specification 2 SCOPE This specification
More informationPrecision Surface Mount Resistors Wirewound or Metal Film Technologies
Precision Surface Mount Resists irewound Metal Film Technologies FEATURES Accding to CECC 40402-801 (wirewound) ide range of ohmic values (0.04 to 1 M) Low temperature coefficient (± 25 ppm/ C available)
More informationThick Film Resistor Networks, Dual-In-Line, Molded DIP
Thick Film Resistor Networks, Dual-In-Line, Molded DIP FEATURES Isolated, bussed, and dual terminator schematics available 0.160" (4.06 mm) maximum seated height and rugged, molded case construction Thick
More informationDATA SHEET HIGH POWER CHIP RESISTORS RC high power series 5%, 1% sizes 0603/0805/1206/2512. RoHS compliant & Halogen free
DATA SHEET HIGH POWER CHIP RESISTORS RC high power series 5%, 1% sizes 0603/005/1206/2512 RoHS compliant & Halogen free Product specification Supersedes Date of Mar. 06, 2003 Product specification 2 SCOPE
More informationMetal-Oxide Varistors (MOVs) Surface Mount Multilayer Varistors (MLVs) > MLN Series. MLN SurgeArray TM Suppressor. Description
MLN SurgeArray TM Suppressor RoHS Description The MLN SurgeArray Suppressor is designed to help protect components from transient voltages that exist at the circuit board level. This device provides four
More informationDATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, X7R
DATA SHEET SURFACE-MOUNT CERAMIC MULTILAYER CAPACITORS General Purpose & High Capacitance Class 2, 6.3 V TO 50 V 100 pf to 22 µf RoHS compliant & Halogen Free Product Specification October 13, 11 V.8 Product
More informationMetal Film Resistors, Non-Magnetic, Industrial, Precision
Metal Film Resistors, Non-Magnetic, Industrial, Precision FEATURES Small size - conformal coated Flame retardant epoxy coating Controlled temperature coefficient Excellent high frequency characteristics
More informationAutomotive and Anti-Sulfuration Chip Resistor 0402
The resistors are constructed in a high grade ceramic body (aluminium oxide). Internal metal electrodes are added at each end and connected by a resistive paste that is applied to the top surface of the
More informationAC and Pulse Film Foil Capacitors KP Radial Potted Type
AC and Pulse Film Foil Capacitors KP Radial Potted Type 0.5 L max. W max. Marking H max. FEATURES 5 mm lead pitch, supplied loose in box taped in ammopack or reel Material categorization: for definitions
More informationMetal Film Resistors, Industrial, Flameproof
End of Life - August 13 Metal Film Resistors, Industrial, Flameproof STANDARD ELECTRICAL SPECIFICATIONS FEATURES Small physical size Low cost resistors have the ability to withstand overloads up to times
More informationDATA SHEET GENERAL PURPOSE CHIP RESISTORS RC0402 5%, 1% RoHS compliant & Halogen Free
DATA SHEET GENERAL PURPOSE CHIP RESISTORS 5%, 1% RoHS compliant & Halogen Free Product specification Supersedes Date of Mar. 06, 2003 Product specification 2 SCOPE This specification describes series chip
More informationCarbon Film Fixed Resistor Axial Leaded
Features Automatically insertable High quality performance Non-Flame type available Cost effective and commonly used Too low or too high values can be supplied on case to case basis Performance Specification
More informationTypes MC and MCN Multilayer RF Capacitors
High-Frequency, High-Power, High-Voltage Chips with Nonmagnetic Option Rugged flexibility and compatibility with FR4 boards make Type MC and MCN capacitors ideal for use where other multilayer caps aren
More informationSurface Mount Multilayer Ceramic Chip Capacitor Solutions for High Voltage Applications
Surface Mount Multilayer Ceramic Chip Capacitor Solutions for High Voltage Applications ELECTRICAL SPECIFICATIONS X7R GENERAL SPECIFICATION Note Electrical characteristics at +25 C unless otherwise specified
More informationHigh Ohmic (up to 68 MΩ)/ High Voltage (up to 10 kv) Resistors
High Ohmic (up to 68 MΩ)/ A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded to the end-caps.
More information3. ELECTRICAL PERFORMANCE PROPERTY TEST CONDITION PERFORMANCE 3. 1 Contact Resistance 1) Center Push 100mΩ Max
1. GENERAL 1. 1 Application : This specification is applied to MULTI WAY SWITCH for electronic equipment. 1. 2 Operating Temperature Range :-25 ~ 70 1. 3 Storage Temperature Range :-0 ~ 85. However, 96
More information50 W Power Resistor, Thick Film Technology, TO-220
50 W Power Resistor, Thick Film Technology, TO-220 FEATURES 50 W at 25 C heatsink mounted Adjusted by sand trimming Leaded or surface mount versions High power to size ratio Non inductive element Material
More informationThick Film Resistor Networks, Military, MIL-PRF-83401 Qualified, Type RZ010 and RZ020 Dual-In-Line, Molded DIP
MDM (Military M831/1 and /2) Thick Film Resistor Networks, Military, MIL-PRF-831 Qualified, Type RZ1 and RZ2 Dual-In-Line, Molded DIP STANDARD ELECTRICAL SPECIFICATIONS VISHAY DALE MODEL/ PIN NO. MIL STYLE
More informationDATA SHEET ARRAY CHIP RESISTORS YC/TC 5%, 1% sizes YC:102/104/122/124/162/164/248/324/158/358 TC: 122/124/164
Product specification December 11, 2015 V.2 0 DATA SHEET ARRAY CHIP RESISTORS YC/TC 5%, 1% sizes YC:102/104/2/4/162/164/248/324/158/358 TC: 2/4/164 RoHS compliant Product specification 2 SCOPE This specification
More informationProduct Specification
Product Specification Model No.: DC-240-L01-00-TR Description: H=3.00mm Horizontal SMD DC Power Jacks Pin Shaft Diameter: 0.65mm Packing Method: Tape & Reel (600pcs./R) 1. General 1a. Scope The jacks should
More informationHigh Ohmic/High Voltage Metal Glaze Leaded Resistors
High Ohmic/High Voltage FEATURES A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded to
More informationNARROW-PITCH (0.8mm) CONNECTORS P8 SERIES
Socket Header Compliance with RoHS Directive NRROW-PITCH CONNECTORS FOR PC ORDS 3. Perfect for portable devices, the bellows-type provide a strong resistance against falling, impacts, and forced insertions
More informationSurface Mount Multilayer Ceramic Chip Capacitors for Automotive Applications
Surface Mount Multilayer Ceramic Chip Capacitors for Automotive Applications FEATURES AEC-Q200 qualified with PPAP available Available in 0402 to 1812 body size Three dielectric materials AgPd termination
More informationHigh Ohmic/High Voltage Metal Film Leaded Resistors
, High Ohmic/High Voltage FEATURES Metal film technology High pulse loading (up to 10 kv) capability Small size (0207/0411) Compatible with lead (Pb)-free and lead containing soldering processes Compliant
More information0.3 mm Contact Pitch, 0.9 mm above the board, Flexible Printed Circuit ZIF Connectors.
0.3 mm Contact Pitch, 0.9 mm above the board, Flexible Printed Circuit ZIF Connectors. FH Series (51pos. type) 3.45mm 17.1mm 0.9mm Features 1. Extremely light weight The largest version, with all contacts
More informationESCC 4001/026 Qualified ( ) High Stability Thick Film Resistor Chips
ESCC 4001/026 Qualified ( ) High Stability Thick Film Resistor Chips thick film chip resistors are specially designed to meet the requirements of the ESA 4001/026 specification. They have undergone the
More informationPart Marking Instructions Chip Resistors
Chip Resistors Part Marking Instructions Part Marking Instructions Chip Resistors 1% Marking The nominal resistance is marked on the surface of the overcoating with the use of 4 digit markings. 0201 and
More informationSD Memory Card Connectors
SD Memory Card Connectors DM Series Withstands higher force of card insertion. Card Standard type Metal cover extends over the back of the connector. Features. Withstands higher force of card insertion
More informationHigh Ohmic/High Voltage Metal Glaze Leaded Resistors
High Ohmic/High Voltage Metal Glaze Leaded Resistors FEATURES Technology: Metal glaze A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive
More informationHigh Ohmic/High Voltage Metal Glaze Leaded Resistors
VR37 High Ohmic/High Voltage FEATURES A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive layer, tinned electrolytic copper wires are welded
More information0.45mm Height 0402 Package Pure Green Chip LED Technical Data Sheet. Part No.: LL-S160PGC-G5-1B
.45mm Height 42 Package Pure Green Chip LED Technical Data Sheet Part No.: LL-S16PGC-G5-1B Spec No.: S16 Rev No.: V.2 Date: Dec./6/25 Page: 1 OF 9 Features: Package in 8mm tape on 7" diameter reel. Compatible
More informationPower Resistor Thick Film Technology
Power Resistor Thick Film Technology LTO series are the extension of RTO types. We used the direct ceramic mounting design (no metal tab) of our RCH power resistors applied to semiconductor packages. FEATURES
More informationDC Film Capacitors MKT Radial Potted Type
DC Film Capacitors MKT Radial Potted Type FEATURES 15 mm to 27.5 mm lead pitch. Supplied loose in box and taped on reel Material categorization: for definitions of compliance please see www.vishay.com/doc?99912
More informationDC Film Capacitors MKT Radial Potted Type
DC Film Capacitors MKT Radial Potted Type MKT80 FEATURES AEC-Q00 qualified (rev. D) for PCM. mm (for larger available components on request) High temperature capabilities, up to 0 C Capacitance up to 60
More informationSC-1000/2000 ROTARY CODED SWITCHES FEATURES PART NUMBER DESIGNATION S C - 1 0 1 0 T B. RoHS compliant
SC-00/2000 RoHS compliant INTERNAL STRUCTURE SC-00 / 2000 series 4 2 3 6 FEATURES BC RoHS compliant Fine click with metallic spring Low profile of 3.9 mm makes perfect for high density board mounting applications
More informationMetal Film Resistors, Military, MIL-R-10509 Qualified, Type RN and MIL-PRF-22684 Qualified, Type RL
CMF (Military RN and RL) Metal Film Resistors, Military, Qualified, Type RN and Qualified, Type RL FEATURES Very low noise (- 40 db) Very low voltage coefficient (5 ppm/v) Controlled temperature coefficient
More informationMetal Film Resistors, Military, MIL-R-10509 Qualified, Precision, Type RN and MIL-PRF-22684 Qualified, Type RL
Metal Film Resistors, Military, Qualified, Precision, Type RN and Qualified, Type RL FEATURES Very low noise (- 40 db) Very low voltage coefficient (5 ppm/v) Controlled temperature coefficient Flame retardant
More informationAC Line Rated Ceramic Disc Capacitors Class X1, 760 V AC, Class Y1, 500 V AC
AC Line Rated Ceramic Disc Capacitors Class X1, 760 V AC, Class Y1, 500 V AC QUICK REFERENCE DATA DESCRIPTION VALUE Ceramic Class 1 2 Ceramic Dielectric U2J U2J Y5S, Y5U Y5S, Y5U Voltage (V AC ) 500 760
More informationY.LIN ELECTRONICS CO.,LTD.
Features Current transfer ratio (CTR 50~600% at I F =5mA, V CE =5V) High isolation voltage between input and output (Viso=5000 V rms ) Creepage distance >7.62 mm Operating temperature up to +110 C Compact
More informationDATA SHEET LOW OHMIC HIGH POWER CHIP RESISTORS RL-High power series 5%, 2%, 1% sizes 0805/1206
DATA SHEET LOW OHMIC HIGH POWER CHIP RESISTORS series 5%, 2%, 1% sizes 005/1206 RoHS compliant Product specification Aug 27, 200 V.2 Product specification 2 SCOPE This specification describes RL005/1206
More informationHigh Ohmic/High Voltage Metal Glaze Leaded Resistors
High Ohmic/High Voltage Metal Glaze Leaded Resistors FEATURES Technology: Metal glaze A metal glazed film is deposited on a high grade ceramic body. After a helical groove has been cut in the resistive
More informationPrecision Leaded Resistors
FEATURES Approved according to CECC 40101-806 Advanced thin film technology Low TC: ± 15 to Precision tolerance of value: ± 0.1 % and ± 0.25 % Superior overall : class 0.05 Wide precision range: 10 Ω to
More informationONE OF THE SMALLEST SNAP-ACTION SWITCHES IN THE WORLD. FEATURES Superminiature type, light-weight snap action switch PC board terminal type (0.
ONE OF THE SMALLEST SNAP-ACTION SWITCHES IN THE WORLD SWITCHES FEATURES Superminiature type, light-weight snap action switch PC board terminal type (0.2g) Solder terminal type with mounting holes (0.3g)
More information1SMB59xxBT3G Series, SZ1SMB59xxT3G Series. 3 Watt Plastic Surface Mount Zener Voltage Regulators
9xxBTG Series, SZ9xxTG Series Watt Plastic Surface Mount Zener Voltage Regulators This complete new line of W Zener diodes offers the following advantages. Features Zener Voltage Range. V to V ESD Rating
More informationInterference Suppression Film Capacitors MKP Radial Potted Type
Interference Suppression Film Capacitors MKP Radial Potted Type FEATURES 7.5 mm to 27.5 mm lead pitch Supplied loose in box, taped on reel Material categorization: For definitions of compliance please
More informationI-PEX MHF4 Micro Coaxial Connector
PRODUCT SPECIFICATION I-PEX MHF4 Micro Coaxial Connector Plug P/N 20448-001R-81 Receptacle P/N 20449-001E RF Connector, RF Cable & Antenna Manufacturer E-mail: sales@wellshow.com.tw Tel: +886-2-24239376
More informationSelection Guide for Conversion of Carbon Composition Resistors
Selection Guide for Conversion of Carbon Composition Resistors believes that the information described in this publication is accurate and reliable, and much care has been taken in its preparation. However,
More informationSM712 Series 600W Asymmetrical TVS Diode Array
SM712 Series 6W Asymmetrical TVS Diode Array RoHS Pb GREEN Description The SM712 TVS Diode Array is designed to protect RS-485 applications with asymmetrical working voltages (-7V to from damage due to
More informationInsulated Precision Wirewound Resistors Axial Leads
Insulated Precision Wirewound Resistors Axial Leads In wirewound precision resistors, the series holds a leading position in professional applications whenever an excellent stability of the ohmic value
More informationMADP-000504-10720T. Non Magnetic MELF PIN Diode
MADP-54-172T Features High Power Handling Low Loss / Low Distortion Leadless Low Inductance MELF Package Non-Magnetic Surface Mountable RoHS Compliant MSL 1 Package Style 172 Dot Denotes Cathode Description
More information3mm Photodiode,T-1 PD204-6C/L3
3mm Photodiode,T-1 Features Fast response time High photo sensitivity Small junction capacitance Pb free This product itself will remain within RoHS compliant version. Description is a high speed and high
More informationOperating Temperature Range: -30 to +85ç (Note 1) Operating Humidity Range: 40 to 80%
All non- products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website search at www.hirose-connectors.com, or contact your Hirose sales representative.
More informationThick Film Chip Resistors, Military/Established Reliability MIL-PRF-55342 Qualified, Type RM
Thick Film Chip Resistors, Military/Established Reliability -PRF-55342 Qualified, Type RM MATERIAL SPECIFICATIONS Resistive element Ruthenium oxide Encapsulation Epoxy Substrate 96 % alumina Termination
More informationTQ SMD RELAYS TQ SMD LOW-PROFILE SURFACE-MOUNT RELAY FEATURES SPECIFICATIONS
LOW-PROFILE SURFACE-MOUNT RELAY RELAYS.55 5.6. FEATURES Low-profile: 6 mm.36 inch (Tape height: max. 6.5 mm.56 inch) Tape and reel package is available as standard packing style Surge withstand between
More informationROTARY CODED SWITCHES (SMD)
COPL ELECTRONICS RoHS compliant INTERNL STRUCTURE ETURES soldering Low profile of. mm Wide variety (top or side setting,, or positions, J-hook, gull wing or throuhg hole pins) to choose from Compatible
More informationDISCONTINUED (1998) FBR46 SERIES. MINIATURE RELAY 2 POLES 1 to 2 A (FOR SIGNAL SWITCHING) RoHS compliant FEATURES
MINIATURE RELAY 2 POLES 1 to 2 A (FOR SIGNAL SWITCHING) FBR46 SERIES RoHS compliant FEATURES Miniature size About 50% smaller in volume compared with the FBR240 series used mainly in communication equipment.
More informationFeatures. Applications. Truth Table. Close
ASSR-8, ASSR-9 and ASSR-8 Form A, Solid State Relay (Photo MOSFET) (0V/0.A/0Ω) Data Sheet Description The ASSR-XX Series consists of an AlGaAs infrared light-emitting diode (LED) input stage optically
More informationPower Resistor for Mounting onto a Heatsink Thick Film Technology
DIMENSIONS in millimeters Power Resistor for Mounting onto a Heatsink Thick Film Technology FEATURES 800 W at 85 C bottom case temperature Wide resistance range: 0.3 to 900 k E24 series Non inductive Easy
More informationKnob Potentiometer with Switch
Knob Potentiometer with Switch The is a revolutionary concept in panel mounted potentiometers. This unique design consists of a knob driving and incorporating a cermet potentiometer. Only the mounting
More informationATC 600S Series Ultra-Low ESR, High Q, NPO RF & Microwave Capacitors
AC 600S Series Ultra-Low ESR, High Q, NPO RF & Microwave Capacitors Features: Lowest ESR in Class Highest Working Voltage in class 250V Standard EIA Size: 0603 Laser Marking (Optional) RoHS Compliant High
More informationINTEGRATED CIRCUITS. For a complete data sheet, please also download:
INTEGRATED CIRCUITS DATA SHEET For a complete data sheet, please also download: The IC06 74HC/HCT/HCU/HCMOS Logic Family Specifications The IC06 74HC/HCT/HCU/HCMOS Logic Package Information The IC06 74HC/HCT/HCU/HCMOS
More informationFT-63 SINGLE TURN CERMET TRIMMERS FEATURES. PART NUMBER DESIGNATION F T - 6 3 E T V 5 k Ω ( 5 0 2 ) RoHS compliant
SINGLE TURN FT-6 RoHS compliant INTERNAL STRUCTURE 4 FEATURES RoHS compliant Resistance tolerance ± 0 % O ring sealed and washable Suitable for automatic insertion and automatic adjustment Increase in
More informationFebruary 2015. Chip Beads. For power line. HF-ACC Series. HFxxACC3216. * Dimensions Code JIS[EIA]
E M C C o m p o n e n t s February 2015 Chip Beads For power line HF-ACC Series HFxxACC3216 [1206 inch]* * Dimensions Code JIS[EIA] (2/8) REMINDERS FOR USING THESE PRODUCTS Before using these products,
More information3216 Ceramic Chip Antenna for Bluetooth/WLAN Application
ANTENNA PRODUCTS Mars Liu C.T.Lee Page 1 sheet 190-1 A4 for Bluetooth/WLAN Application Preliminary Product Specification Quick Reference Data Centre Frequency Bandwidth VSWR Polarization Azimuth Beamwidth
More informationGas Discharge Tube (GDT) Products CG5 and SL0902A Series. CG5 and SL0902A Series
Description Agency Approvals AGENCY AGENCY FILE NUMBER E128662 2 Electrode GDT Graphical Symbol Littelfuse Broadband Optimized SL0902A Series offers high surge ratings in a miniature package. Special design
More informationDATA SHEET THICK FILM CHIP RESISTORS Introduction
DATA SHEET THICK FILM CHIP RESISTORS Introduction Product Specification Product specification 2 Chip Resistor Surface Mount Data in data sheets is presented - whenever possible -according to a 'format',
More informationEVERLIGHT ELECTRONICS CO., LTD.
ECN : PAGE : 1/7 Features : Fast response time High photo sensitivity Small junction capacitance High reliability Description : is a high speed silicon NPN epitaxial planar phototransistor in a compact
More informationCeramic Trimmer Capacitors
!Note T3E8.pdf 2.9.2 Ceramic Trimmer Capacitors TZB4 Series.±. Depth.5.4±. dia. Features. Miniature rectangular shape : 4.(W)x4.5(L)x3.(H)mm. 2. Color coded case facilitates identification of capacitance
More informationEVERLIGHT ELECTRONICS CO.,LTD.
Technical Data Sheet 0603 Package Chip LED (0.8 mm Height) Features Package in 8mm tape on 7 diameter reel. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow
More informationEVERLIGHT ELECTRONICS CO.,LTD.
Technical Data Sheet Chip LED with Bi-Color (Multi-Color) Features Package in 8mm tape on 7 diameter reel. Compatible with automatic placement equipment. Compatible with infrared and vapor phase reflow
More informationFor board-to-fpc. Narrow Pitch Connectors (0.35mm pitch)
For board-to-fpc Narrow Pitch Connectors (0.35mm pitch) S35 Series New FEATURES 1. 1.7 mm wide slim two-piece type connector Mated height 0.6 mm Smaller compared to A4F series Width: Approx. 44% down
More informationHow To Power A Power Control Microprocessor (Power Control) Microprocessor 2 (Power) (Power Power) (Control) (Repower) Microcontroller (Power/Reflow) (Mini) (Microprocessor) (Wired) (Wire
PTC NTC for Surface Mounting Application What is a Thermistor? Thermally Sensitive Resistor Thermistor Positive Temperature Coefficient PTC Negative Temperature Coefficient NTC Characteristics of Thermistors
More informationContents. 12. Lot Number 10. 13. Reel Packing Structure 11. 14. Precaution for Use 13. 15. Hazard Substance Analysis 14. 16. Revision History 18
Rev : 00 ISSUE NO : DATE OF ISSUE : 2009. 04. 10 S P E C I F I CATION MODEL : SLHNNWW629T1S0U0S0 [Rank : (S0), (U0), (S0)] HIGH POWER LED - SUNNIX6 CUSTOMER : CUSTOMER CHECKED CHECKED APPROVED SAMSUNG
More informationKnob Potentiometer FEATURES. P16NP P16NM Panel Cutout. Thickness nut 2 mm washer 1.5 mm. Panel sealing ring 12 wrench Thread M10 x 0.75 10.2 9.
Knob Potentiometer P6, PA6 FEATURES Test according to CECC 4000 or IEC 60393- P6 - Version for professional and industrial applications (cermet) W at 40 C PA6 - Version for professional audio applications
More informationDYNACAP Double Layer Capacitor
DX Series (Terminal shaped V, H) Combines two coin cells using laser welding technology to obtain a rated voltage of 5.5V. Available in either vertical or horizontal terminal leads, they are 11.5 mm in
More informationKSC Series Sealed Tact Switch for SMT
KSC Series Features/enefits Positive tactile feeling J or G terminations Various heights IP67 Typical Applications Automotive Cellular phones Industrial electronics Network infrastructure and IT Elevator
More informationO WA-120U series IP67. 120W Single Output Switching Power Supply. Features. Aplications
Features UniversalACinput/Fulrange Built-inactivePFCfunction Higheficiencyupto91% Protections:Shortcircuit/Overcurent/ Overvoltage/Overtemperature Fanlesdesign,colingbyfreairconvection Colingbyfreairconvection
More informationQUICK REFERENCE DATA. Pilkor components FEATURES APPLICATIONS
MKP RADIAL POTTED CAPACITORS Pitch 10.0/15.0/22.5/27.5 mm QUICK REFERENCE DATA Capacitance range (E6 series) * 0.01μF to 3.3μF Capacitance tolerance ±10 %, ±20 % Rated (AC) voltage 50 to 60 Hz 275 V ~
More information1 POLE - 5A SLIM POWER RELAY
POWER RELAY POLE - A SLIM POWER RELAY FTR-MY Series RoHS compliant FEATURES Width mm, height mm,(% smaller than NY series) area mm, super slim, low power, compact and light weight.gr. Nominal power: mw
More informationMCS 0402 AT, MCT 0603 AT, MCU 0805 AT, MCA 1206 AT - Precision www.vishay.com. Precision Thin Film Chip Resistors
Precision Thin Film Chip Resistors FEATURES Rated dissipation P 70 up to 0.4 W for size 1206 AEC-Q200 qualified Approved to EN 140401-801 Superior temperature cycling robustness Sulfur resistance verified
More information