15/40/80CN Series Medium Pressure Filters

Transcription

1 1/4/8CN Series Medium Pressure Filters Max 32 l/min - 7 bar Global Filtration Technology

2 1/4/8CN Series TYPICAL APPLICATIONS Compressor Lube Oil Off-line Filter Loops Machine Tools (Automotive Standard) Hydrostatic Drive Charge Pumps Mobile Equipment Pilot Lines For Servo Controls Oil Patch Drilling Equipment Injection Moulding The Parker Filtration 1/4/8CN Series Medium Pressure Filters. This partial list of applications for Parker CN Series Filters has a common factor, the need for an economical, medium pressure range filter with excellent fatigue pressure ratings. Prior to the availability of the CN filter, applications such as those listed were restricted by limitations of a spin-on can, or forced into the higher-cost range of high pressure filters. The CN Series fills this gap, and now with the newly increased fatigue rating from 4 to 6 bar the applications are expanded. 6 bar fatigue rating eight times that of a spin-on) Diametral (side) seal between head and bowl Dust Seal 4CN-2 meets automotive H3 standard 1CN meets automotive HF2 standard Cast aluminium head Reinforced Microglass III replacement elements FEATURES ADVANTAGES BENEFITS Complete performance data disclosure Visual, electrical or electrical/visual indicators available Ability to provide reliable service under tough cyclic operating conditions Can be utilised in applications where high pressure filters may have been only option Proven reliability in cyclic applications Reduced importance of bowl torque Prevents contamination from building up on bowl/head threads Automotive industry acceptance Low profile, lightweight and durable Multi-layered design produced high capacity and efficiency Wire support reduces pleat bunching, keeps performance consistent All pertinent information is provided in an easy-to-compare format Check element condition at a glance Right style for the application Reduced downtime due to premature filter failures Reduced costs, better fit for the application No downtime, no leaks Performs with real world service Easier service, eliminates thread galling Satisfies specifications without need for further testing and/or approval Less weight, smaller envelop and cleaner appearance Great performance value Reliable performance throughout element life Reduces downtime, maximises element life No hidden deficiencies Easy selection of proper filtration Optimise element life, prevent bypassing Matches your system electrical connections *Fluoroelastomers are available under various registered trademarks, including Viton (a registered trademark of DuPont) and Fluorel (a registered trademark of 3M) 64

3 SPECIFICATION Medium Pressure Filters 1/4/8CN Series Maximum Allowable Operating Pressure: 7 bar Operating Temperature Range: -26 C to 13 C (Fluoroelastomer Seals) -42 C to 17 C (Nitrile) Materials of Construction: Aluminium head, hard anodized aluminium bowl Filtration Media: Microglass III. (See Table 4). For E Series consult Parker Filtration Ports: Inlet and outlet ports are threaded internally, flange faced ports available on 8CN Port Style Model 1CN 4CN 8CN BSPF(G) 1, 3 /4 1 1 /4, 1 1 /2 1 1 /2, 2 SAE 12, 16 16, 24 24, 32 ISO 6149 M27 M33 M42, M48 Metric 3-M config 2 Bypass Valve & Indicator Settings: Table following gives bypass valve and corresponding indicator 1CN 4CN 8CN 16.6 (6.17) 17.8 (6.73) 28.9 (11.6).7 (9.87) (1.33) 41.6 (1.81) 46. (1.83) 62. (2.44) 77.7 (3.6).4 (1.9) 32.6 (1.28) 49. (1.9) 71.1 (2.8) 17.2 (4.22) (4.91) 8.9 (3.38) 127. (.) 18.7 (6.) 73.2 (2.88) 111. (4.37) 82.6 (3.) setting Bypass Indicator 1.7 bar 1.2 bar 3. bar 2. bar Weights (Kg): Model Length 1 Length 2 1CN CN CN Fluid Compatability: Suitable for use with mineral and vegetable oils, and some synthetic oils. For other fluids, please consult Parker Filtration Seal Material: Nitrile or Fluoroelastomer* Electrical Ratings: Power - VA max, Current -. A max (resistive), Voltage - 28 VDC max, 28 VAC (-6Hz) max, Contacts - normally open and normally closed, wired to DIN plug pin code (option code E2 only) DIMENSIONS (mm) MODEL A B C D E F G H I J K L M N P 1CN 82.6 (3.) (4.8) 11.4 (.96) 4CN 38.1 (1.) 62. (2.44) 11.6 (4.) 22.9 (.9) 31.8 (1.) 41.1 (1.62) 42.9 (1.69) 8.8 (2.32) 79.4 (3.12) 36.6 (1.44) 6.2 (2.37) 41.3 (1.63) xM6-1.x7.9 DEEP 1-2 ft lbs 4xM8-1.x13 DEEP 4- ft lbs 4xM8-1.x16 DEEP 6-7 ft lbs 8CN H I N H J N H J N F G L K F G L K G L K F J Torque -3 ft. lbs (34-4 Nm) I I Torque -3 ft. lbs (34-4 Nm) M D M D M D C C C Single Length A Double Length B P Single Length A Double Length B P Single Length A Double Length B P Element Removal Clearance 2. (63.) 1. (.4) Nominal Hex E SAE - 4 Drain Plug Element Removal Clearance 2. (63.) 1. (.4) Nominal Hex E SAE - 4 Drain Plug Element Removal Clearance 2. (63.) 1. (.4) Nominal Hex E SAE - 4 Drain Plug Torque -3 ft. lbs 6

4 1/4/8CN Series 8CN FLANGE FACE DETAILS FLANGE FACE MOUNTING HOLES M x 22 DEEP INDICATOR DETAILS Visual/Electrical Indicator CODE E2 Visual Indicator CODE M Option Connection/Voltage Wiring Part Number M2 Visual Auto Reset N/A N/A (1.7 bar) (3.4 bar) E2 Visual/Electrical Auto Reset 28 VDC 28 VAC MAX 1 C 2 NC 3 NO (1.7 bar) (3.4 bar) Note: For full indicator specifications see Section 6. 66

5 PRESSURE DROP CURVES Medium Pressure Filters 1/4/8CN Series To select the correct housing and element it is recommended that the ratio between the bypass setting and the pressure drop across the filter with a clean element should be at least 3:1. All filters were tested in accordance with ISO "Determination of pressure drop flow characteristics of hydraulic fluid power filters", using mineral oil fluid SAE 1 at 32 cst viscosity. 1CN-1 Elements CN-1 Empty Housing Q2 Q Q1 Q C /4 Nominal Port Size 1 Nominal Port Size CN-2 Elements 1CN-2 Empty Housing Q C Q Q1 Q /4 Nominal Port Size Nominal Port Size

6 1/4/8CN Series 4CN-1 Elements 4CN-1 Empty Housing Nominal Port Size Q2 Q Q1 1C Q2. 11/2 Nominal Port Size CN-2 Elements 4CN-2 Empty Housing Q2 Q 1C Q1 Q Nominal Port Size 11/2 Nominal Port Size CN-1 Elements 8CN-1 Empty Housing Q2 Q Q1 Q C /2 Nominal Port Size 2 Nominal Port Size CN-2 Elements 8CN-2 Empty Housing Q2 Q Q Q /2 Nominal Port Size 1 2 Nominal Port Size Note: All above data is calculated at 3cSt Rel density

7 1/4/8CN Series Element Service A. Stop the system s power unit. B. Relieve any system pressure in the filter line. C. Drain the filter bowl if drain port option is provided. D. Loosen and remove bowl. E. Remove element by pulling downward with a slight twisting motion and discard. F. Check bowl o-ring and anti-extrusion ring for damage and replace if necessary. G. Lubricate element o-ring with system fluid and place on post in filter head. H. Install bowl by rotating counter clockwise and tighten to specified torque. 1CN 1-2ft. lbs (2-27 Nm) 4CN 42-ft. lbs (7-68 Nm) 8CN 6-7ft. lbs (8-9 Nm) I. Confirm there are no leaks after powering the system. Index CN Filters Parts List Head Options (Consult Factory) Indicators M2-Visual Auto Reset; 1.7 bar M2-Visual Auto Reset; 3. bar E2-Electrical/Visual; 1.7 bar c/w DIN 436 Connector E2-Electrical/Visual; 3. bar c/w DIN 436 Connector Bypass Valve 1.7 bar assembly 3. bar assembly Element (See Model Code Page) Bowl Single Length With Drain Single Length Without Drain Double Length With Drain Double Length Without Drain Bowl and Dust Seal Nitrile (Buna N) Fluoroelastomer Drain Plug; SAE-4 Nitrile (Buna N) Fluoroelastomer

8 1/4/8CN Series PREFERRED PRODUCTS TABLE The following standard filters are supplied with 3.4 bar bypass and Nitrile seals. Part Number 1CN-1-2Q-M2--C2C2-1 1CN-1-Q-M2--C2C2-1 1CN-1-1Q-M2--C2C2-1 1CN-1-2Q-M2--C2C2-1 1CN-2-2Q-M2--C2C2-1 1CN-2-Q-M2--C2C2-1 1CN-2-1Q-M2--C2C2-1 1CN-2-2Q-M2--C2C2-1 4CN-1-2Q-M2--E2E2-1 4CN-1-Q-M2--E2E2-1 4CN-1-1Q-M2--E2E2-1 4CN-1-2Q-M2--E2E2-1 4CN-2-2Q-M2--E2E2-1 4CN-2-Q-M2--E2E2-1 4CN-2-1Q-M2--E2E2-1 4CN-2-2Q-M2--E2E2-1 8CN-1-1Q-M2--F2F2-1 Part Number 1CN-1-2Q-E2--C2C2-1 1CN-1-Q-E2--C2C2-1 1CN-1-1Q-E2--C2C2-1 1CN-1-2Q-E2--C2C2-1 1CN-2-2Q-E2--C2C2-1 1CN-2-Q-E2--C2C2-1 1CN-2-1Q-E2--C2C2-1 1CN-2-2Q-E2--C2C2-1 4CN-1-2Q-E2--E2E2-1 4CN-1-Q-E2--E2E2-1 4CN-1-1Q-E2--E2E2-1 4CN-1-2Q-E2--E2E2-1 4CN-2-2Q-E2--E2E2-1 4CN-2-Q-E2--E2E2-1 4CN-2-1Q-E2--E2E2-1 4CN-2-2Q-E2--E2E2-1 8CN-1-1Q-E2--F2F Media Rating Q2 Q Q1 Q2 Q2 Q Q1 Q2 Q2 Q Q1 Q2 Q2 Q Q1 Q2 Q1 Ports G 2 Replacement Elements 92893Q G441Q Q 93367Q 92893Q G4169Q 92892Q 93368Q Q G448Q 92683Q 9399Q Q G4167Q Q 93118Q 93268Q Note: Filter assemblies ordered from the Part Number Matrix below are on extended lead times. Where possible, please make your selection from the table above. PART NUMBER MATRIX Table 1 Table 2 Table 3 Table 4 Table Table 6 Table 7 Table 8 Table 9 Table 1 F3 4CN 1 1Q M2 E2E2 1 Nitrile Fluoroelastomer* Table 4 Table 7 Seals Ports G 3 /4 Thread G1 12, SAE Thread 16, SAE Thread M27, ISO 6149 G1 1 /4 G1 1 /2 16, SAE Thread 24, SAE Thread M33, ISO 6149 G1 1 /2 G2 24, SAE Thread 32, SAE Thread 2 3-M Flange Face M42, ISO 6149 M48, ISO 6149 MODEL 1CN 4CN 8CN O F3 Degree of Filtration B2B2 C2C2 M4M4 N4N4 B3B3 D2D2 E2E2 N4N4 P4P4 C3C3 E2E2 F2F2 P4P4 R4R4 Y3Y3 D3D3 E3E3 Table 2 Table 3 Table Model Number Housing Length Symbol 1CN 4CN 8CN Average filtration ratio ß (ISO 16889) / particle size µm(c) N/A N/A N/A N/A N/A 4. N/A N/A N/A Water removal 4CN & 8CN only MODEL 1CN-1 1CN-2 4CN-1 4CN-2 8CN-1 8CN-2 CODE 2Q Q 1Q 2Q WR Q Q 92893Q Q Q 93266Q Q Nitrile Seals Q G441Q G4169Q G448Q G4167Q 93267Q Q Q Q 92892Q 92683Q Q 93268Q Q Q Q 93368Q 9399Q 93118Q Q Q Single Length Double Length 1.7 bar 3.4 bar If No Bypass option (II) & an indicator is selected, above symbols (, ) denote indicator settings. Replacement Element Part Numbers Indicator No Indicator (use with 11 option, no bypass only No Indicator (use when model is equipped with bypass valve) Visual/Auto reset FPC Visual/Auto reset Electric Switch DIN 436 FPC Electric DIN 436 FPC Electronic L.E.D. N * Fluoroelastomers are available under various registered trademarks, including Viton (a registered trademark of DuPont) and Fluorel (a registered trademark of 3M) 1C MODEL 1CN-1 1CN-2 4CN-1 4CN-2 8CN-1 8CN-2 Fluoroelastomer Seals Q Q Q Q Q 93269Q 93266Q Q G4189Q G419Q G4191Q G4192Q 93266Q Q 1 2 Table 6 Bypass Indicator Setting Table 8 Options None No Bypass Drain port on bowl No bypass and drain port Q Q Q Q Q Q Q Table 9 Q Q 9337Q 931Q 93119Q 92993Q Q Design Number 1C P M2 V3 E2 TW3 FW3 Applied to the filter assembly by Parker Filtration. MODEL 1CN 4CN 8CN Nitrile () S94 S96 S343 Seal Kits Fluoroelastomer* (F3) S9 S97 S344 7