H1 Axial Piston Pump, Size 078, Single Technical Information Dimensions

Transcription

1 Input Shafts Option G1, ISO , outer dia 32 mm-4 (SAE C, 14 teeth) 31.5 ±1 [1.240 ±0.039] MOUNTING FLANGE SURFACE FLANGE PER ISO SPLINE DATA NUMBER OF TEETH : 14 PITCH FRACTION : 12/24 PRESSURE ANGLE : 30 PITCH-Ø : TYP OF FIT : FLAT ROOT, SIDE FIT PER : ANSI B CLASS 5 Ø26 ±0.25 [1.024 ±0.010] Ø31.14 ±0.09 [1.226 ±0.004] 8.05 ±0.8 [0.317 ±0.031] 48 ±1 [1.890 ±0.039] COUPLING MUST NOT PROTRUDE BEYOND THIS SURFACE Option G9, ISO , outer dia 38 mm-4 (SAE C-C, 23 teeth) P E Specifications Option Spline Min active spline length 2 Torque rating 1 Rated torque Maximum torque mm [in] Nm Nm G1 14 teeth, 12/24 pitch [1.238] 534 [4720] 816 [7220] For definitions of maximum and rated torque values, refer to: Basic Information Manual , section Shaft Torque Ratings and Spline Lubrication. Minimum active spline length for the specified torque ratings. T E MOUNTING FLANGE SURFACE FLANGE PER ISO ±1 [1.594 ±0.039] SPLINE DATA NUMBER OF TEETH : 23 PITCH FRACTION : 16/32 PRESSURE ANGLE : 30 PITCH-Ø : Ø [Ø1.438] TYP OF FIT : FLAT ROOT, SIDE FIT PER : ANSI B CLASS 5 Specifications 8.05 ±0.8 [0.317 ±0.031] Ø33.6 ±0.25 [1.323 ±0.010] COUPLING MUST NOT PROTRUDE BEYOND THIS SURFACE Ø37.59 ±0.09 [1.480 ±0.004] 54 ±1 [2.126 ±0.039] P E Option Spline Min active spline length 2 Torque rating 1 Rated torque Maximum torque mm [in] Nm Nm G9 23 teeth, 16/32 pitch [1.588] 999 [8840] 1818 [16 090] For definitions of maximum and rated torque values, refer to: Basic Information Manual , section Shaft Torque Ratings and Spline Lubrication. Minimum active spline length for the specified torque ratings. T E

2 Input Shafts Option F1, ISO , outer dia 35 mm-4 (SAE C, 21 teeth) 34.5 ±1 [1.358 ±0.039] MOUNTING FLANGE SURFACE FLANGE PER ISO SPLINE DATA NUMBER OF TEETH : 21 PITCH FRACTION : 16/32 PRESSURE ANGLE : 30 PITCH-Ø : Ø33,337 [Ø1,313] TYP OF FIT : FLAT ROOT, SIDE FIT PER : ANSI B CLASS ±0.8 [0.317 ±0.031] Ø30.4 ±0.25 [1.197 ±.010] 48 ±1 [1.890 ±0.039] COUPLING MUST NOT PROTRUDE BEYOND THIS SURFACE Ø34.42 ±0.09 [1,355 ±,004] P E Specifications Option Spline Min active spline length 2 Torque rating 1 Rated torque Maximum torque mm [in] Nm Nm F1 21 teeth, 16/32 pitch 34.5 [1.358] 760 [6730] 1137 [10 060] For definitions of maximum and rated torque values, refer to: Basic Information Manual , section Shaft Torque Ratings and Spline Lubrication. Minimum active spline length for the specified torque ratings. T E

3 Input Shafts Option F4, ISO , Code 38-3, Diameter 38.1 taper 1:8, without key and no through-hole in the end of the shaft (38,1) [1.500] MOUNTING FLANGE SURFACE FLANGE PER ISO CONICAL KEYED SHAFT END SIMILAR TO ISO CODE 38-3 SUITABLE KEY 3/8x3/8x1 1/2 ANSI B ±0,5:1000 SHAFTS 1 1/8-12UNF 7.88 ±0.8 [0.310 ±0.031] (47) [1.850] 81.9 ± ±1 [1.374 ±0.039] [3.224 ±0.039] COUPLING MUST NOT OVERLAP TILL THIS POINT P E Specifications Torque rating 1) Option Tapered shaft Rated torque* Maximum torque Nm Nm F taper without key 1116 [9880] 1488 [13 170] For definitions of maximum and rated torque values, refer to: Basic Information Manual , section Shaft Torque Ratings and Spline Lubrication. Mating part must maintain a minimum gap width of 1.0 mm with the shaft shoulder after installation of the part. Transmittable torque will be reduced if the minimum gap requirement is not met. Tapered shaft customer acknowledgement The Sauer-Danfoss H1 tapered shaft has been designed using the industry standard ISO , minus the through-hole in the end of the shaft. Sauer-Danfoss recommends a self-locking nut instead of a castle nut and pin. The nut and mating square-cut key are customer supplied. The specified torque rating of the tapered shaft documented above is based on the cross-sectional diameter of the shaft, through the keyway, and assumes the proper clamp and fit between shaft and coupling. Sauer-Danfoss guarantees the design and manufactured quality of the tapered shaft. The customer is responsible for the design and manufactured quality of the mating female coupling and key and applied torque on the nut. Sauer-Danfoss has made provisions for the key in accordance to the ISO specification with the understanding that the key is solely to assist in the installation of the mating coupling. T E C Torque must be transmitted by the taper fit between the shaft and it s mating coupling, not the key. Torque or loading inadvertently transmitted by the customer supplied key may lead to premature shaft failure

4 Auxiliary Mounting Pads Option H2, ISO , flange 82-2 (SAE A, 9 teeth) 2x ±0.35 [4.189 ±0.014] 4x 53.2 ±0.18 [2.09 ±0.007] MOUNTING FLANGE SURFACE FLANGE 82-2 PER ISO ±2 [ ±0.079] ±2 [ ±0.079] [0.583] [3.489] [3.252] R0.8 MAX [0.031] THREAD: M10x1.5-6H THD DEPTH: 15 [0.591] MIN. RECOMMENDED SCREW-IN DEPTH 1.5 x THREAD DIA 4x O-RING SEAL REQUIRED REF [3.237] I.D [0.103] CROSS SECTION [0.077] ±0.25 [0.319 ±0.010] [2.428] AUXILIARY PUMP SHAFT LENGTH SPLINE DATA NUMBER OF TEETH : 9 PITCH FRACTION : 16/32 PRESSURE ANGLE : 30 PITCH- : [ ] TYP OF FIT : FILLET ROOT, SIDE FIT PER : ANSI B CLASS 6 P E Specifications Option Spline Torque rating 1 maximum torque Nm H2 9 teeth, 16/32 pitch 162 [1430] For definitions of maximum torque values, refer to: Basic Information Manual , section Shaft Torque Ratings and Spline Lubrication. T E C Standard pad cover is installed only to retain coupling during shipping. Do not operate pump without an auxiliary pump or running cover installed

5 Auxiliary Mounting Pads Option H1, ISO , flange 82-2 (SAE A, 11 teeth) 2x ±0.35 [4.189 ±0.014] 4x 53.2 ±0.18 [2.09 ±0.007] MOUNTING FLANGE SURFACE FLANGE 82-2 PER ISO [0.780] ±2 [ ±0.079] ±2 [ ±0.079] [3.489] [3.252] R0.8 MAX [0.031] THREAD: M10x1.5-6H THD DEPTH: 15 [0.591] MIN. RECOMMENDED SCREW-IN DEPTH 1.5 x THREAD DIA 4x O-RING SEAL REQUIRED REF [3.237] I.D [0.103] CROSS SECTION [0.077] 8.1 ±0.25 [0.319 ±0.010] MAX. AUXILIARY PUMP SHAFT LENGTH SPLINE DATA NUMBER OF TEETH : 11 PITCH FRACTION : 16/32 PRESSURE ANGLE : 30 PITCH- : [ ] TYP OF FIT : FILLET ROOT, SIDE FIT PER : ANSI B CLASS 6 MIN ACTIVE SPLINE LENGTH 105MM P E Specifications Option Spline Torque rating 1 maximum torque Nm H1 11 teeth, 16/32 pitch 296 [2620] For definitions of maximum torque values, refer to: Basic Information Manual , section Shaft Torque Ratings and Spline Lubrication. T E C Standard pad cover is installed only to retain coupling during shipping. Do not operate pump without an auxiliary pump or running cover installed

6 Auxiliary Mounting Pads Option H3, ISO , flange (SAE B, 13 teeth) 2x 146 ±0.35 [5.748 ±0.014] 4x 73 ±0.18 [2.87 ±0.007] MOUNTING FLANGE SURFACE FLANGE PER ISO [0.780] ±2 [11.32 ±0.079] ±2 [ ±0.079] [4.245] R0.8 MAX [0.031] [4.002] THREAD: M12x1.75-6H THD DEPTH : 20 [0.787]MIN. RECOMMENDED SCREW-IN DEPTH 1.5 x THREAD DIA 4x O-RING SEAL REQUIRED REF [ 3.989] ID X 2.62 [0.103] CROSS SECTION [0.077] 11.4 ±0.25 [0.449 ± 0.010] [2.428] AUXILIARY PUMP SHAFT LENGTH SPLINE DATA NUMBER OF TEETH : 13 PITCH FRACTION : 16/32 PRESSURE ANGLE : 30 PITCH- : [ 0.813] TYP OF FIT : FILLET ROOT, SIDE FIT PER : ANSI B CLASS 6 P E Specifications Option Spline Torque rating 1 maximum torque Nm H3 13 teeth, 16/32 pitch 395 [3500] For definitions of maximum torque values, refer to: Basic Information Manual , section Shaft Torque Ratings and Spline Lubrication. T E C Standard pad cover is installed only to retain coupling during shipping. Do not operate pump without an auxiliary pump or running cover installed

7 Auxiliary Mounting Pads Option H5, ISO , flange (SAE B-B, 15 teeth) 2x 146 ±0.35 [5.748 ±0.014] 4x 73 ±0.175 [2.874 ±0.007] MOUNTING FLANGE SURFACE FLANGE PER ISO [0.780] ±2 [ ±0.079] ±2 [ ±0.079] [4.245] [4.002] R0.8 MAX [0.031] THREAD: M12x1.75-6H THD DEPTH : 20 [0.787]MIN. RECOMMENDED SCREW-IN DEPTH 1.5 x THREAD DIA 4x O-RING SEAL REQUIRED REF [3.989] ID X 2.62 [.103] CROSS SECTION [0.077] 11.4 ±0.25 [0.449 ±0.010] [2.428] AUXILIARY PUMP SHAFT LENGTH SPLINE DATA NUMBER OF TEETH : 15 PITCH FRACTION : 16/32 PRESSURE ANGLE : 30 PITCH- : [ 0.938] TYP OF FIT : FILLET ROOT, SIDE FIT PER : ANSI B CLASS 6 P E Specifications Option Spline Torque rating 1 maximum torque Nm H5 15 teeth, 16/32 pitch 693 [6130] For definitions of maximum torque values, refer to: Basic Information Manual , section Shaft Torque Ratings and Spline Lubrication. T E C Standard pad cover is installed only to retain coupling during shipping. Do not operate pump without an auxiliary pump or running cover installed

8 Auxiliary Mounting Pads 2x ±0.35 [4.508 ±0.014] 4x ±0.18 [2.25 ±0.007] Option H6, ISO , flange (SAE C, 14 teeth) MOUNTING FLANGE SURFACE FLANGE PER ISO [0.865] ±2 [ ±0.079] ±2 [ ±0.079] 2x 90.5 ±0.175 [3.563 ±0.007] 181 ±0.35 [7.126 ±0.014] [5.278] [5.002] THREAD : M12x1.75-6H THD DEPTH: 21 [0.823] MIN RECOMMENDED SCREW-IN DEPTH 1.5 x THREAD DIA 4x THREAD : M16 x2-6h THD DEPTH: 25 [0.984] MIN RECOMMENDED SCREW-IN DEPTH 1.5 x THREAD DIA 2x O-RING SEAL REQUIRED REF [4.737] I.D [0.103] CROSS SECTION [0.077] 13.5 ±0.25 [0.531± 0.010] [2.514] AUXILIARY PUMP SHAFT LENGTH SPLINE DATA NUMBER OF TEETH : 14 PITCH FRACTION : 12/24 PRESSURE ANGLE : 30 PITCH- : [ 1.167] TYP OF FIT : FILLETT ROOT, SIDE FIT PER : ANSI B CLASS 6 MIN ACTIVE SPLINE LENGTH 17.8MM P E Specifications Option Spline Torque rating 1 maximum torque Nm H6 14 teeth, 12/24 pitch 816 [7220] For definitions of maximum torque values, refer to: Basic Information Manual , section Shaft Torque Ratings and Spline Lubrication. T E C Standard pad cover is installed only to retain coupling during shipping. Do not operate pump without an auxiliary pump or running cover installed

9 Port Description SERVO GAGE PORT "M4" PORT ISO / MAX CLEARANCE DIA FOR FITTING SYSTEM PORT "B" BAR SPLIT FLANGE BOSS PER ISO 6162 M12 X MIN. FULL THREAD DEPTH RECOMMENDED SCREW-IN DEPTH 1.5 x THREAD DIA CONNECTOR : DEUTSCH DT04-2P CASE PRESSURE PORT 42 MAX CLEARANCE DIA FOR FITTING CCW Rotation CW Rotation M12 X 1,75 SYSTEM PORT "A" BAR SPLIT FLANGE BOSS PER ISO 6162 M12 X MIN. CASE DRAIN PORT "L4" FULL THREAD DEPTH PORT ISO /16-12 RECOMMENDED SCREW-IN DEPTH 48 MAX CLEARANCE DIA FOR FITTING 1.5 x THREAD DIA CHARGE INLET PORT "S" PORT ISO / MAX CLEARANCE DIA FOR FITTING SYSTEM A GAGE PORT "MA" PORT ISO / MAX CLEARANCE DIA FOR FITTING P E Port description Port Description Sizes A System port A 25.4 B System port B 25.4 E 7 /8-14 F 7 /8-14 L2 1 1 /16-12 L4 1 1 /16-12 MA System A gage port 9 /16-18 MB 9 /16-18 M3 9 /16-18 M4 Servo gage port 7 /16-20 M5 Servo gage port 7 /16-20 M14 7 /16-20 S 1 5 /16-12 T E

10 Port Description SYSTEM B GAGE PORT "MB" PORT ISO / MAX CLEARANCE DIA FOR FITTING CHARGE PRESSURE CONSTRUCTION PORT PORT ISO /16-24 CHARGE FILTRATION PORT "F" 42 MAX CLEARANCE DIA FOR FITTING TO FILTER CASE GAGE PORT "M14" PORT ISO / MAX CLEARANCE DIA FOR FITTING (EDC, FNR, NFPE) CHARGE FILTRATION PORT "E" 42 MAX CLEARANCE DIA FOR FITTING FROM FILTER CASE PRESSURE PORT Ø42 MAX CLEARANCE DIA FOR FITTING CONNECTOR : DEUTSCH DT04-2P SERVO GAGE PORT "M5" PORT ISO / MAX CLEARANCE DIA FOR FITTING CHARGE PRESSURE CONSTRUCTION PORT PORT ISO /16-24 CASE DRAIN PORT "L2" PORT ISO / MAX CLEARANCE DIA FOR FITTING CHARGE GAGE PORT "M3" PORT ISO / MAX CLEARANCE DIA FOR FITTING AFTER FILTERING P E

11 152.9 ±1.0 [6.02 ±0.04] Z Servo gage port M4 Port ISO / max. clearance dia for fitting System port B bar Split flange boss per ISO 6162 M12x min. full thread depth recommended screw-in depth 1.5 x thread dia ±1.0 [4.96 ±0.04] ±1.0 [4.09 ±0.04] 69.5 ±1.0 [2.74 ±0.04] [ ] [ ] (4x)27.8 ±0.25 [1.09 ±0.01] 52.0 ±0.2 [2.05 ±0.01] (8x)13.9 ±0.25 [0.55 ±0.01] Charge inlet port S Port ISO / max. clearance dia for fitting (8x) 28.6 ±0.25 [1.13 ±0.01] System port A bar Split flange boss per ISO 6162 M12x min. full thread depth recommended screw-in depth 1.5 x thread dia B-B (2x) Connector : Deutsch DT04-2P to be paint free C (4x) 57.2 ±0.25 [2.25 ±0.01] ±2 [ ±0.079] [ ] C [ ] C-C D D 92.4 ±0.2 [3.64 ±0.01] ±1.0 [6.07 ±0.04] ±1.0 [5.48 ±0.04] ±1.0 [5.34 ±0.04] B B 15 ±0.2 [0.59 ±0.01] Case drain port L4 Port ISO / max. clearance dia for fitting 45.2 ±1.0 [1.78 ±0.04] Case pressure port Port ISO / max. clearance dia for fitting ±0.25 [0.49 ±0.01] 1.5 ±0.5 x 45 ±5 [0.059 ±0.020 x 45 ] R 0.8 max. [0.031] 89.0 ±0.2 [3.50 ±0.01] Shafts to be paint free 48.0 ±1 [1.89 ±0.04] D-D Mounting flange surface Flange per ISO to be paint free 8.05 ±0.8 [0.32 ±0.03] 31.5 ±1 [1.24 ±0.04] [ ] Coupling must not protrude beyond this surface Shaft LC Shaft LC Shaft LC P E

12 Y mm [in] 45.2 ±1.0 [1.78 ±0.04] Case pressure port Port ISO / max. clearance dia for fitting ±1.0 [6.07 ±0.04] ±1.0 [5.48 ±0.04] Connector : Deutsch DT04-2P to be paint free Servo gage port M5 Port ISO / max. clearance dia for fitting Charge pressure construction port Port ISO / ±2 [5.44 ±0.079] 1.37 [0.054] Z ±2 [4.29 ±0.079] ±1.0 [6.02 ±0.04] ±1.0 [4.96 ±0.04] ±1.0 [4.09 ±0.04] G ±2.0 [7.04 ±0.079] X 23.7 [0.93] G 95.0 ±2.0 [3.74 ±0.079] Case drain port L2 Port ISO / max. clearance dia for fitting 99.7 ±1.0 [3.93 ±0.04] [5.62] Approximate center of gravity Charge gage port M3 Port ISO / max. clearance dia for fitting after filtering Approximate center of gravity G-G W 88.0 ±0.2 [3.46 ±0.01] F-F Shaft LC ±2 [8.118 ±0.079] ±2 [5.055 ±0.079] CASE GAGE PORT "M14" PORT ISO / MAX CLEARANCE DIA FOR FITTING 77.2 ±1 [3.039 ±0.039] Y ±1 [9.111 ±0.039] ±1 [9.154 ±0.039] ±1 [9.272 ±0.039] F E SYSTEM B GAGE PORT "MB" PORT ISO / MAX CLEARANCE DIA FOR FITTING CHARGE PRESSURE CONSTRUCTION PORT PORT ISO / ±1 [0.276±0.039] F 67 ±1 [2.638 ±0.039] 53.5 ±1 [2.106 ±0.039] E CHARGE FILTRATION PORT "F" 42 MAX CLEARANCE DIA FOR FITTING TO FILTER CHARGE FILTRATION PORT "E" 42 MAX CLEARANCE DIA FOR FITTING FROM FILTER 12 E-E Charge filtration port F Port ISO / max. clearance dia for fitting to filter 96.5 ±1.0 [3.80 ±0.04] 96.6 ±1.0 [3.78 ±0.04] Charge filtration port E Port ISO / max. clearance dia for fitting from filter P E

13 View W View X mm [in] SYSTEM A GAGE PORT "MA" PORT ISO / MAX CLEARANCE DIA FOR FITTING ±1 [8.505 ±0.039] 67 ±1 [2.638 ±0.039] CCW Rotation CW Rotation 4x ±0.25 [2.254 ±0.010] 4x 30 ±0.25 [1.181 ±0.010] OTHER SIDE SCREW HEAD SPACE 4x ±0.25 [2.254 ±0.010] 4x w ±0.19 [0.565 ±0.007] P E

14 Controls Electric Displacement Control (EDC), option A2 (12 V)/A3 (24 V) mm [in] CONNECTOR : DEUTSCH DT04-2P 209 MAX [8.228] ±2 [5.055 ±0.079] 64.2 ±1 [2.528 ±0.039] CASE GAGE PORT "M14" PORT ISO /16-20 Ø21 MAX CLEARANCE DIA FOR FITTING SHAFT 77.2 ±1 [3.039 ±0.039] MOUNTING FLANGE ± 1 [7.042 ± 0.039] 2x ± 1 [6.018 ± 0.039] SHAFT CONNECTOR : DEUTSCH DT04-2P 2x ± 1 [5.484 ± 0.039] P E Electric Displacement Control (EDC), with manual override, option A4 (12 V)/A5 (24 V) CONNECTOR : DEUTSCH DT04-2P 209 MAX [8.228] ± 2 [5.055 ± 0.079] 64.2 ± 1 [2.528 ± 0.039] CASE GAGE PORT "M14" PORT ISO / MAX CLEARANCE DIA FOR FITTING SHAFT 77.2 ± 1 [3.04 ± 0.039] MOUNTING FLANGE ± 1 [7,042 ± 0.039] 2x ± 1 [6.018 ± 0.039] CONNECTOR : DEUTSCH DT04-2P P E SHAFT 2x139.3 ± 1 [5.484 ± 0.039]

15 Controls Forward-Neutral-Reverse (FNR) with manual override, option A9 (12 V)/B1 (24 V) CONNECTOR : DEUTSCH DT04-2P mm [in] 209 MAX [8.228] ± 2 [5.055 ± 0.079] 64.2 ± 1 [2.528 ± 0.039] CASE GAGE PORT "M14" PORT ISO / MAX CLEARANCE DIA FOR FITTING SHAFT MOUNTING FLANGE CONNECTOR DEUTSCH DT04-2P: 77.2 ± 1 [3.04 ± 0.039] ± 1 [7.042 ± 0.039] 2x ± 1 [6.018 ± 0.039] SHAFT 2x ± 1 [5.484 ± 0.039] P E Non Feedback Proportional Electric control (NFPE), with manual override, option A8 (12 V)/B8 (24 V) CONNECTOR: DEUTSCH DT04-2P 209 MAX [8.228] ± 2 [5.055 ± 0.079] 64.2 ± 1 [2.528 ± 0.039] CASE GAGE PORT "M14" PORT ISO / MAX CLEARANCE DIA FOR FITTING SHAFT PLUG REMOVING CAN CAUSE CONTAMINATION ISSUES 77.2 ± 1 [3.04 ± 0.039] MOUNTING FLANGE ± 1 [7.058 ± 0.039] 2x ± 1 [6.018 ± 0.039] SHAFT CONNECTOR: DEUTSCH DT04-2P 2x ± 1 [5.484 ± 0.039] P E

16 2x WRENCH SIZE 4 Displacement limiters Displacement limiters, option B ±1 [5.156 ±0.039] 150 MAX [5.906] 150 MAX [5.906] mm [in] 84.5 ±1 [3.327 ±0.039] 2x WRENCH SIZE 13 P E

17 Filtration Suction filtration, option L mm [in] [8.505] x 28.6 ±0.25 [1.126 ±0.010] 4x 57.2 ±0.25 [2,252 ±0.010] CHARGE PRESSURE CONSTRUCTION PORT PORT ISO /16-24 SYSTEM B GAGE PORT "MB" PORT ISO /16-18 Ø28 MAX CLEARANCE DIA FOR FITTING SYSTEM PORT "B" Ø BAR SPLIT FLANGE BOSS PER ISO 6162 M12 X MIN. FULL THREAD DEPTH RECOMMENDED SCREW-IN DEPTH 1.5 x THREAD DIA CHARGE INLET PORT "S" [2.559] PORT ISO /16-12 Ø63 MAX CLEARANCE DIA FOR FITTING 8x 13.9 ±0.25 [0.547 ±0.010] 4x 27.8 ±0.25 [1.094 ±0.010] [2.559] SYSTEM PORT "A" Ø BAR SPLIT FLANGE BOSS PER ISO 6162 M12 X MIN. FULL THREAD DEPTH RECOMMENDED SCREW-IN DEPTH 1.5 x THREAD DIA P E

18 Filtration Remote full charge pressure filtration, option P for end cap option F5 (SAE-C PTO) 12 F-F mm [in] SYSTEM B GAGE PORT "MB" PORT ISO /16-18 Ø28 MAX CLEARANCE DIA FOR FITTING 8.5 ±1 [0.335±0.039] 67 ±1 [ ±0.039] CHARGE FILTRATION PORT "F" Ø42 MAX CLEARANCE DIA FOR FITTING TO FILTER ±1 [4.197 ±0.039] F F 55.5 ±1 [2.185 ±0.039] 12 E-E E E CHARGE FILTRATION PORT "F" Ø42 MAX CLEARANCE DIA FOR FITTING TO FILTER CHARGE FILTRATION PORT "E" Ø42 MAX CLEARANCE DIA FOR FITTING FROM FILTER CHARGE PRESSURE CONSTRUCTION PORT PORT ISO /16-24 CHARGE FILTRATION PORT "E" Ø42 MAX CLEARANCE DIA FOR FITTING FROM FILTER 96.5 ±1 [3.799 ±0.039] P

19 Filtration Integral full flow charge pressure filtration with filter bypass sensor, option M mm [in] ±1 [7.333 ±0.039] ±1 [8.215 ±0.039] ±1 [4.853 ±0.039] CONNECTOR: DEUTSCH DTM04-2P CHARGE GAGE PORT "M6" PORT ISO /16-18 Ø28 MAX CLEARANCE DIA FOR FITTING BEFORE FILTER 40.6 ±1 [1.598 ± 0.039] ±1 [3.061 ±0.039] ±1 [ ±0.039] ±1 [ ±0.039] ±1 [2.110 ±0.039] P E

20 Filtration Integral full flow charge pressure filtration with filter bypass sensor, option M, for end cap option F4 (SAE-C PTO) mm [in] ±1 [7.806 ±0.039] ±1 [8.687 ±0.039] ±1 [5.326 ±0.039] CONNECTOR: DEUTSCH DTM04-2P ±1 [2.110 ±0.039] CHARGE GAGE PORT "M6" PORT ISO /16-18 Ø28 MAX CLEARANCE DIA FOR FITTING BEFORE FILTER ±1 [3 061 ±0 039] 40.6 ±1 [1.598 ±0.039] ±1 [ ±0.039] ±1 [ ±0.039] P

21 Filtration External full flow charge pressure filtration, option S for end cap options D8 or F ±1 [9.111 ±0.039] CHARGE INLET PORT "S" PORT ISO /16-12 CLOSED WITH PLUG ±1 [9.154 ±0.039] E SYSTEM B GAGE PORT "MB" PORT ISO / MAX CLEARANCE DIA FOR FITTING CHARGE PRESSURE CONSTRUCTION PORT PORT ISO /16-24 E 67 ±1 [2.638 ± 0.039] 53.5 ±1 [2.106 ± 0.039] CHARGE FILTRATION PORT "E" 42 MAX CLEARANCE DIA FOR FITTING FROM FILTER 12º E-E CHARGE FILTRATION PORT "E" 42 MAX CLEARANCE DIA FOR FITTING FROM FILTER 96.5 ±1 [3.799 ± 0.039] P mm [in]