Form Measurement. Surftest SJ-400. Bulletin No Portable Surface Roughness Tester

Transcription

1 Form Measurement Surftest SJ-400 Bulletin No. 203 Portable Surface Roughness Tester

2 Surftest SJ-400 Series Revolutionary New Portable Surface Roughness Testers Make Their Debut Long-awaited performance and functionality are here: compact design, skidless and high-accuracy roughness measurements, multi-functionality and ease of operation. Requirement High-accuracy measurements with a hand-held tester wide range, high-resolution detector and an ultra-straight drive unit provide class-leading accuracy. Detector Measuring range: 800µm Resolution: μm (on 8μm range) Drive unit Straightness/traverse length SJ-40: 0.3µm/.98"(25mm) SJ-402: 0.5µm/.96"(50mm) Requirement 3 Cylinder surface roughness measurements with a hand-held tester The skidless measurement and R-surface compensation functions make it possible to evaluate cylinder surface roughness. SJ-40 SJ-402 SJ-40 Requirement 2 Roughness parameters that conform to international standards The SJ-400 Series can evaluate 36 kinds of roughness parameters conforming to the latest ISO, DIN, and NSI standards, as well as to JIS standards (994/982). Requirement 4 Measurement/evaluation of stepped features and straightness Ultra-fine steps, straightness and waviness are easily measured by switching to skidless measurement mode. The ruler function enables simpler surface feature evaluation on the LCD monitor. 2

3 Requirement 5 dvanced data processing with extended analysis The SJ-400 Series allows data processing identical to that in the high-end class. These data analysis and report creation capabilities are achieved using the surface roughness analysis program FORMTRCEPK V5 or SJ-Tools. Measurement pplications R-surface measurement Fine contour measurement with an auto-leveling table Deep groove measurement Requirement 6 Confirmation of measurement results and assessed profiles without a printout The large, integrated, touch-panel LCD monitor clearly displays evaluation results and measured profiles. Upside down measurement Calculation Result Screen Measured Profile Screen Cylinder measurement with a support foot 3

4 The SJ-400 Series Performs Skidless Measurements The SJ-400 Series detector uses interchangeable nosepieces that allow skid or skidless measurements to suit the type of measurement required. Skidless measurement Traverse direction Skidded measurement Traverse direction Skid Traverse direction Traverse direction Tilt compensation function The Tilt Compensation Datum Points are selectable from all of the profile (choose P and P2) or any arbitrary two sections on the profile (choose P, P2, P3 and P4), as required. If you choose adjacent sections for tilt compensation then the characteristics of features of interest between these sections, such as scratch depth, etc, can be measured directly. Simplified surface feature evaluation with the ruler function This function determines the coordinate difference between two arbitrary points so feature characteristics, such as step height and width, etc, can be measured. Ruler function key Ruler Ruler nalysis Screen Coordinate difference Ruler key 4

5 Powerful Support for Leveling The height/tilt adjustment unit comes as standard for leveling the drive unit prior to making skidless measurements and, supported by guidance from the unique DT function, makes it easy to achieve highly accurate alignment. The DT Function Height adjustment Turn tilt adjustment knob by.37 turns counter-clockwise to level Tilt adjustment Height/tilt adjustment unit DT screen guides the user when leveling With DT Preliminary measurement DT screen (adjustment amount) Final measurement Without DT Preliminary measurement Intuitive adjustment using the tilt adjustment knob OK Repeat NG DT Function for the optional leveling table djust the micrometer head by mm to level With the SJ-400 mounted on a stand, the DT function also works with the optional leveling table. DT screen guides the user when leveling 5

6 More Measuring Functions Than Expected From a Compact Tester Measuring curved-surface roughness (skidless measurement) Usually, a spherical or cylindrical surface (R-surface) cannot be evaluated, but, by removing the radius with a filter, R-surface data is processed as if taken from a flat surface. Statistics Statistical processing can be performed on multiple measurements for one roughness parameter. Histograms can be displayed and printed in addition to statistical results (mean, standard deviation, maximum/minimum value and acceptance ratio). Measurement of a cylindrical surface Statistical R-Surface compensation Switchable Histograms Built-in thermal printer high quality, high-speed thermal printer prints out measured results. It can also print a BC curve or an DC curve as well as calculated results and assessed profiles. These results and profiles are printed out in landscape format, just as they appear on the LCD, in easy-to-understand form. 6

7 GO/NG indication Upper and lower tolerance limits can be set for up to 3 roughness parameters. GO/NG indication is displayed after a measurement. The calculation result is highlighted if NG. uto-calibration The SJ-400 Series is equipped with Ra calibration and step calibration methods for detector calibration (gain adjustment). In both calibration methods only the calibrated value of the precision specimen needs to be entered. No other operations are required to calibrate the tester. GO sign NG sign Calculation Result Screen with GO / NG judgment result Real sampling This function samples stylus displacement for a specified time without engaging detector traverse. This function has a wide range of uses, such as a simplified vibration meter or a displacement gage incorporated in another system. Recalculating Previously measured data can be recalculated for use in other evaluations by changing the current standard, assessed profile and roughness parameters. rbitrary length measurement This function allows a sampling length to be arbitrarily set in.004" (0.mm) increments SJ-40:.004" to.98" (0.mm to 25mm), SJ-402:.004" to.96" (0.mm to 50mm). It also allows the SJ-400 Series to make both narrow and wide range measurements. Key masking Locks out input from the touch panel keys. This eliminates the possibility of the operator accidentally changing the calibration or measurement conditions. Calibration Screen Storing/recalling measured data and conditions The measurement conditions and data can be stored in the control unit or memory card (optional) and recalled as required. Batch printout of data after on-site measurement improves measuring efficiency. Storage capacity Measurement conditions Measurement data Control unit: 5 conditions Memory card: 20 conditions Memory card: 50 or more pieces of data Customizing The SJ-400 Series can be set up to calculate and display only a subset of the roughness parameters available. Parameters can be added later for recalculation, if required. Invalidated Customized Screen 7

8 Wide Choice of Evaluation Possibilities with nalyzing Program FORMTRCEPK V5 SJ-400 Series measurement data can be transferred into FORMTRCEPK V5 by using a memory card (Optional) for detailed analysis. SJ-400 FORMTRCEPK See the FORMTRCEPK brochure (Bulletin No. 200) for more details. Simplified Communication Program (SJ Tools) One of the various functions of the Surftest SJ-400 Series is the ability to use RS-232 with a simplified communication program that allows the transfer of measurement data into a calculation software. The program must be used with Microsoft Excel to generate the inspection report and/or certificate. This program can be downloaded for free from the Mitutoyo website. Required environment: * OS: * Spreadsheet software: Windows 2000-SP4 Microsoft Excel 2000 Windows XP Microsoft Excel 2002 Windows Vista Microsoft Excel 2003 Windows 7 Microsoft Excel 2007 *Windows OS & Microsoft Excel are products of Microsoft Corporation. Requires RS-232C cable (Optional) SJ-400 Series RS-232C cable Order No *RS-232C cable D-sub9pin x 2 (store purchase) is a straight cable. *RS-232C acannot be used in a USB connector. 8

9 Carrying case is a standard accessory Specification Order No. SJ (inch/mm) (inch/mm) SJ (inch/mm) (inch/mm) Measuring method Skidless/Skidded measurement Measuring range Z-axis 32000µin, 3200µin, 320µin (800µm, 80µm, 8µm) (Up to 2,400µm with an option stylus) X-axis SJ-40: (25mm) SJ-402: 2 (50mm) Drive method Straightness SJ-40: 2µin/ (0.3µm/25mm) SJ-402: 20µin/2 (0.5µm/50mm) Measuring speed.002,.004,.02,.04 /s (0.05, 0., 0.5,.0mm/s) Return speed.02,.04,.08 /s (0.5,.0, 2.0 mm/s) Height-Tilt Tilt adjustment range ±.5 adjustment unit Height adjustment amount.39 (0mm) ssessed profile Primary profile (P), Roughness profile (R), Filtered waviness profile (W), DIN4776, MOTIF (R, W) Evaluation parameters Ra, Ry, Rz, Rq, Pc, R3z, mr, Rt, Rp, Rv, Sm, S, δc, Rk, Rpk, Rvk, Mr, Mr2,, 2, Lo, Ppi, R, R, Rx, a, q, Ku, HSC, mrd, Sk, W, W, Wte, Wx, Vo nalysis graphs Bearing rea Curve (BC), mplitude Distribution Curve (DC) Number of sampling length X, X3, X5, XL* (*=arbitrary length) rbitrary length SJ-40:.0 to (.0 increments) [0. to 25mm (0.mm increments)] SJ-402:.04 to 2 (.0 increments) [0. to 50mm (0.mm increments)] Sampling length (L).003,.0,.03,.,.3 (0.08, 0.25, 0.8, 2.5, 8mm) Printing width.89 (48mm)/paper width: 2.28 (58mm) Recording Vertical magnification 0 to 00K magnification, uto magnification Horizontal magnification to K magnification, uto Detector Detection method Differential inductance method Minimum resolution.005µin (320µin range)/ µm (8µm range) Stylus tip Cone, Radius 5µm, Diamond Cone 60, Radius 2µm, Diamond Measuring force 4mN 0.75mN Radius of skid.57 (40mm) Skid force Less than 400mN Function Customize Display/Roughness parameter selectable Data compensation R-surface, Tilt compensation Ruler function Displays the coordinate difference of any two points D..T. function Helps to adjust leveling during skidless measurement Displacement detection mode Enables the stylus displacement to be input while the drive unit is stopped Statistical processing Maximum value, Minimum value, Mean value, Standard deviation (s), Pass ratio, Histogram Tolerance judgment Upper and lower limit values for three parameters can be specified Measuring Condition storage Five sets of measuring conditions (control unit) Printer Thermal printer Cut-off length.003,.0,.03,.,.3 (0.08, 0.25, 0.8, 2.5, 8mm) Digital filter 2CR, PC75 (phase corrected), Gaussian Calibration Ra, Step (utomatic calibration entering the value of roughness specimen) Power supply Via C adapter, built-in rechargeable battery (Ni-H) Battery Charging time 5 hours Number of measurements 600 maximum without printing Power consumption 43W (max.) Dimension Control unit 2.09 x6.50 x3.7 (307x65x94mm) Height-Tilt adjustment unit 5.6 x2.48 x3. (3x63x99mm) Drive unit SJ-40: 5.04 x.42 x.85 (28x36x47mm) SJ-402: 6.08 x.4 x.84 (55x36x47mm) Roughness standard JIS (JIS B /994/982), DIN, ISO, NSI LCD size Touch panel Data output RS-232C input/output, SPC output External control Connection to data processing system (option) Mass Control unit 2.64lbs. (.2kg) Height-Tilt adjustment unit.88lbs. (0.4kg) Drive unit SJ-40:.32lbs. (0.6kg) SJ-402:.4lbs. (0.64kg) Standard accessories C adapter, Carrying case, Printing paper, Touch pen, Protect sheet, Skidless nosepiece, User s manual, one-sheet manual, tools Inch/(Metric) 9

10 Optional ccessories ø ø4 4 Detector (0.75mN): Detector (4mN): ø7 4 Skid nosepiece 2B355 ø8 Detector Extension rods (2G202: 50mm, 2G203: 00mm) Styli Unit: Inch(mm) Standard stylus Detail-.76 (44.7).04 (0.9).30 (7.6).20 2E882 [µm]* 2E924 [µm]** 2C73 [2µm]* 2B403 [5µm]** 2B45 [0µm]** 2E883 [250µm] 2X long for deep hole.2 (3).07 (.8) (94.7) 2E898 [2µm]* 2E94 [5µm]** For small hole.06 (.6).0 (0.4) Detail-.02 ø (44.4).02.3 (3.4).06 (.6).59 (5).09 (2.4) 2C732 [2µm]* 2B404 [5µm]** 2B46 [0µm]** For small hole/2x long for deep hole Detail-.02 ø.02.3 (3.4).06 (.6).02.8 (30) 3.72 (94.4).09 (2.4) 2E892 [2µm]* 2E8 [5µm]** [ ): Tip radius For extra small hole.05 (.2) Detail-.0 (0.4) ø.0 (ø0.3).05 (.2).74 (44.2).35 (8.9) ø.02.0 (2.5) 2C733 [2µm]* 2B405 [5µm]** 2B47 [0µm]** For small hole Ball ø.06 (ø.6).6 (4) 3.69 (93.8) 2E884 [.03 (0.8mm)] For extra minute hole.03 (0.8) Detail-.0 (0.4) ø.0 (ø0.3).03 (0.8).35 (8.9) ø (44.2).0 (2.5) 2C734 [2µm]* 2B406 [5µm]** 2B48 [0µm]** For ultra small hole Ball ø0.5.7"(4.3).2"(3.) ø(ø0.5) 7.48"(37.7) 7.33"(8.5) ø0.3 Detail- ø.0" (ø0.3).72"(43.8) ø.3" (ø3.2) ø2.4 2J662 [.0 (0.25mm)] For deep hole (2X long and 3X long) Detail-.30 (7.6).04 (0.9) (94.7).30 (7.6).04 (0.9).20 Detail (44.7) 5.42 (37.7) For small slotted hole.06 (.6).0 (0.4) Detail-.02 ø (94.4) (45) ø.0 (ø0.3) 2X stylus 2C740 [2µm]* 2B43 [5µm]** 2B425 [0µm]** 3X stylus 2C74 [2µm]* 2B44 [5µm]** 2B426 [0µm]** 2E938 [2µm]* 2E940 [5µm]** 0

11 For deep groove.39 (0mm) Detail-.04 (0.9).56 (4.2).5 (3).76 (44.7) 2C735 [2µm]* 2B409 [5µm]** 2B42 [0µm]** Styli For deep groove.78 (20mm)/2X Long for deep hole. (23).86 (2.8).20 n.05 (n.2) 3.75 (95.2) Unit: Inch(mm) 2E893 [2µm]* 2E9 [5µm]** [ ): Tip radius For deep groove.78 (20mm) Detail-.95 (24.2).9 (23).04 (0.9).76 (44.7) 2C736 [2µm]* 2B408 [5µm]** 2B420 [0µm]** For deep groove.57 (40mm).72 (43.8).68 (42.6) (45.2) Ø.09 (Ø2.4) Ø.05 (Ø.2) 2E895 [2µm]* 2E9 [5µm]** For deep groove.8 (30mm) Detail-.30 (33).25 (3.8) (45.2) 2C737 [2µm]* 2B407 [5µm]** 2B49 [0µm]** For deep groove.8 (30mm)/2X Long for deep hole.44 (36.5).38 (35) (93.8) Ø.2 (Ø3) 2E894 [2µm]* 2E90 [5µm]** For gear tooth Detail-.30 (7.6).25 (6.4).72 (43.8) 60 2B339 [2µm]* 2B40 [5µm]** 2B422 [0µm]** For gear tooth/2x Long for deep hole.44 (36.5).38 (35).27 (6.77) 3.69 (93.8) 60 ø.2 (ø3) 2E896 [2µm]* 2E92 [5µm]** For rolling circle waviness surface.30 (7.6).76 (44.7).03 (0.9).20 Ball ø.06 (ø.588) 2B338 [.03 (0.8mm)] For rolling circle waviness/2x Long for deep hole.30 (7.6).25 (6.4) 3.73 (94.7).03 (0.9).20 2E886 [.0 (0.25mm)] For knife-edge detector Detail-.03 (0.9).30 (7.6).76 (44.7) 2C738 [2µm]* 2B4 [5µm]** 2B423 [0µm]** For corner hole/2x Long for deep hole.23 (5.8).20 (5) ø.03 (ø0.8).38 (35) 45 ø.06 (ø.6) 3.69 (93.8) 2E897 [2µm]* 2E93 [5µm]** For eccentric arm (7.6) (45.2) (0.9) 2C739 [2µm]* 2B42 [5µm]** 2B424 [0µm]** For bottom surface.02 (0.5).24 (6.2).20 (5).74 (44.3) 25 ø.04 (ø) 2E899 [2µm]* 2E95 [5µm]** Detail-

12 3 4 ) 2.36"(60) ø.55" (ø4) Skid nosepiece (2B344).55"(4) Optional ccessories Detector ø.3" (ø8) ø.27" (ø7) (.3).2" (3.) Skidless nosepiece (2B355) [.08"(2m)]* [.8"(5m)] [(0m)] [.08"(2m)]* [.8"(5m)] [(0m)].30"(7.6).85"(2.5).92"(23.5) Stylus tip position.26" (6.7).06"(.6) pplicable skid nosepiece.6"(5.6).5"(3.8) ø.2"(ø3).22"(5.6).".85"(2.5).22"(5.6) 50 (2.8).92"(23.5).27" Stylus tip (6.8) 2B344 position 2B345 Unit: Inch/(Metric).22".85"(2.5) (5.6) R2.92"(23.5).06"(.4) Unit: Inch/(Metric) 2B346 pplicable Stylus skid tip position.77"(9.5).5"(3.8) nosepiece.85"(2.5).22"(5.6) (.4).7" (.4) R2 (.4).85"(2.5).07"(.8) R2 (4.4).93"(23.5)."(2.8).35"(9) 2B349.26" 2B350 (6.7).5"(3.8) (.3).29" (7.5) [.08"(2m)]* [.8"(5m)] [(0m)].77"(9.5).5"(3.8).85"(2.5).08"(2) ø.07".85"(2.5).22"(5.6) Set configuration/dimensions.88"(22.3) (.4).7"(.2) (.4) (ø.9) R2 (.4).85"(2.5).07"(.8) 2B347 R2 (4.4).93"(23.5) Unit: Inch/(Metric) "(2m)]*."(2.8).07"(27.2) 2.36"(60).55"(4).35"(9) ø.06" Stylus tip position "(5m)].94"(24) 2B349 pplicable skid nosepiece.77"(9.5).5"(3.8) (ø.5) 2B350.2"(3) "(0m)].2"(3).85"(2.5).07"(.8).0"(2.5) R2 (.4) (5).35".85"(2.5) (5) [.08"(2m)]* (9).35"(9) 2B35 2B352.46"(.6) [.8"(5m)]." Stylus Skid nosepiece (2B344) Detector (2.8) [(0m)] "(2m)]* ø.06" "(5m)].07"(27.2) 2.36"(60).55"(4).77"(9.5).77"(9.5).5"(3.8).5"(3.8) (ø.5) Stylus tip position.85"(2.5).2"(3).22"(5.6) (.4).7" (.4).94"(24) R2 (.4).2" "(0m)].85"(2.5).85"(2.5).07"(.8).07"(.8).2"(3).0"(2.5) R2 (.4) R2 (4.4).93"(23.5) (3.)."(2.8) Stylus pplicable skid (5) nosepiec.35"(9).85"(2.5) (5) (9).35"(9) "(2m)]* 2B349 2B350 2B348 2B35 2B352 Standard type.46"(.6).76"(44.7) "(5m)] ) 2C73 [.08"(2m)]* Skidless nosepiece.".5" Stylus Skid nosepiece (2B344) Detector.48"(37.7).03" "(0m)].7).04"(0.9).77"(9.5) (2.8) (0.9) 2B403 [.8"(5m)] (2B355) (3.8).7" R2.85"(2.5).07"(.8) (4.4) 2B45 [(0m)] (.4).35"(9) (.4).85"(2.5).22"(5.6) Unit: Inch/(Metric).85"(2." 8"(2m)]* ø ".92"(23.5) (2.8).92"(23.5 2) Stylus ø.06" 8"(5m)] pplicable skid nosepiece Detail - Stylus tip "(2m)]*.77"(9.5).5"(3.8) (ø.5) 2B348.2"(3) Stylus tip 9"(0m)].2"(3) position 2B344 position "(5m)] Standard type.85"(2.5).07"(.8).0"(2.5) (.4) Stand, Tables R2 Stylus tip.76"(44.7) position.5" 2C73 [.08"(2m)]* (5) "(2m)]*.35" "(0m)].48"(37.7).77"(9.5).03" (3.8).7".85"(2.5) R2 (5) (9) Small.35"(9) hole type XY leveling tables 7 (0.9) "(5m)].85"(2.5).07"(.8) 2B403 2B35 (4.4) [.8"(5m)] 2B352 (.4).75"(44.4).6"(5.6) Skidless nosepiece 2B45.35"(9) (.4).46"(.6) "(0m)] [(0m)] 2C732 [.08"(2m)]*.48"(37.7).85"(2.5).22"(5.6).59" ø." 2B404.85"(2.5) [.8"(5m)].22"(5.6) 3 ø 50.92"(23.5) (5) (2.8).92"(23.5) 2B46 [(0m)].27".22" Detail - Stylus tip Stylus [ tip]: Tip radius (6.8).85"(2.5) (5.6) R2 position 2B344 position 2B345.6"(4).92"(23.5).06"(.4) "(2m)]* Detail - 8"(2m)]* "(5m)] 2B348 Small hole type 8"(5m)] "(0m)].75"(44.4).85"(2.5) 2B355.6"(5.6).5" 2C732 [.08"(2m)]* R2 "(2m)]* 9"(0m)].48"(37.7).77"(9.5) (3.8).7" Extra small hole type.0".59" ø.85"(2.5).09".07"(.8) 2B404 R2 (4.4) [.8"(5m)].74"(44.2) (mm) (mm) (mm) "(5m)] Stylus tip (0.4).26".48"(37.7) 2C733 [.08"(2m)]* (5) 2B46 (.4).85"(2.5) (2.3).35"(9) [(0m)] (.4) 2B353.22" (6.7) "(0m)] position (inch/mm) (inch/mm) (inch/mm).35".85"(2.5) ø.0".78"(9.7) (0.5).7" (5.6) 2B405 [.8"(5m)] R2 (8.9) (ø0.3).09"(2.3) (.4) (4.4) (.4).92"(23.5).06"(.4) 2B47 [(0m)] Detail - 2B346 Inch(mm).85"(2.5).08"(2) ø.07" Order No , , , "(22.3) (.2) (ø.9) Detail - Table size 5.2 x 3.94 (30 x 00mm) 8"(2m)]* 8"(5m)] Extra small hole type Maximum loading.0".09" R2 5kgf.74"(44.2) Stylus tip (0.4).85"(2.5) (2.3) 2B353 Inclination.48"(37.7) Extra small hole type.26" angle ±.5 9"(0m)] position 2C733 [.08"(2m)]*.78"(9.7) (0.5).7" ø.0".74"(44.2) Horizontal (6.7) rotating.0" angle ±3.35" 2B405 [.8"(5m)] (.4) (ø0.3).09"(2.3) (4.4) (.4).48"(37.7) (0.4) (8.9) X, Y axis displacement 2C734 ±.49 (2.5mm) [.08"(2m)]* 2B47 [(0m)] ±.49 (2.5mm) ±.49 (2.5mm).35".85"(2.5) ø.0".08"(2) ø.07" 2B406 [.8"(5m)] Min. reading (0.00mm)*.00 (0.00mm)* (0.00mm)* (8.9) of.88"(22.3) the (ø0.3) micrometer (.2) head(ø.9) Detail - 2B48 [(0m)] 2B347 Dimension 0.3"x9.7"x3.27" 8.66"x7.44"x3.27" 0.3"x9.7"x2.6" Detail - (262x233x83mm) (220x89x83mm) (262x233x55mm) "(2m)]* 8"(2m)]* Extra small hole type Mass 3.89 lbs. (6.3kg) 3.22 lbs. (6kg).02 lbs. (5kg) "(5m)].74"(44.2).85"(2.5).0".09".22"(5.6) Flat R2 8"(5m)] Stylus tip.48"(37.7) (0.4) 2C734 [.08"(2m)]* 2B353 Deep hole type * Digital display.93"(23.5).85"(2.5) (2.3)."(2.8) "(0m)] 9"(0m)] position.35" 3.73"(94.7) ø.0" (0.5) Stylus 5.70"(44.7).78"(9.7) 2B406 tip position.7" [.8"(5m)] 2B354 (8.9) (ø0.3) 3.45"(87.7).04"(0.9) 5.42"(37.7).09"(2.3).04"(0.9) 2B48 (.4) (4.4) [(0m)] (.4) Detail - "(2m)]* distinguish ø ø.85"(2.5).22"(5.6) "(5m)] Flat.93"(23.5)."(2.8) 2 "(0m)] Deep hole type Detail - 2 x stylus Detail - 3 x stylus "(2m)]* 2B354.09" (2.4) pplicable skid nosepiece ø.0" (2.5).0" (2.5) ø.06"(.6).3"(3.4) ø (.2).03"(0.8).50" (2.8).53"(3.4).8".0" (0.4) (.2).27" (6.8).30"(7.6).06" (.6).03"(0.8).4"(0.4).06"(27)."(22.8) ø.27"(ø7) Unit: Inch/(Metric) Inch(mm).33" (8.4).50" (2.8) (5).53"(3.4) pplicable skid nosepiece.8".50" (2.8).53"(3.4).33" (8.4) (5).8".33" (8.4) (5).79"(20).79"(20).79"(20).8".8".24"(6.).06"(27)."(22.8).06"(27)."(22.8).24"(6.).8" ø.55" (ø4) ø.55" ø.55" (ø4) (ø4).24"(6.) ø.55" (ø4).26" (6.7).26" (6.7) ø.55" (ø4).53" (3.4).53" (3.4).70"(7.9).53"(3.4).8".70"(7.9).53"(3.4).53" (3.4).70"(7.9).53"(3.4).8".04" ().04" () ø.55" (ø4).8".04" ().09" (2.4) ø.0" (2.5).0" (2.5) ø.3" (ø8) ø.06"(.6).3"(3.4) ø (.2).03"(0.8) Detector : 0.75mN measuring force, with 2C73 standard type stylus (2µm tip radius) : 4mN measuring force, with 2B403 standard type stylus (5µm tip radius).26" (6.7).06"(.6) Extension Rods (2G202:.97"(50mm), 2G203: 3.94"(00mm) ø.27" (ø7).30"(7.6).0" (0.4) (.2).5"(3.8).27" (6.8).30"(7.6).06" (.6).5"(3.8).03"(0.8).4"(0.4) (.3) ø.2"(ø3).29" (7.5).30"(7.6) ø.55" (ø4) ø.3" (ø8).26" (6.7).06"(.6) ø.27" (ø7).5"(3.8) (.3).5"(3.8) ø.

13 3." (99) Precision vise Can be used with the XY leveling table. Leveling table (for D..T. function) Can be used with the XY leveling tables. Table swivels: ±.5 Table size: 5.2"x3.94" (30x00mm) Max. Loading: 5kgf Order No Clamping method Sliding jaws Jaw opening.42 (36mm) Jaw width.73 (44mm) Jaw depth.63 (6mm) Height.50 (38mm) Cylinder attachment Used to attach on a cylinder Diameter: ø.59" up to 2.36" (ø5mm up to 60mm) Manual column stand Column travel: 7.87"(200mm) Dimensions: 4.57"x7.87"x29.3" (370x200x740mm) Mass: lbs. (3kg) (mm) (inch/mm) 2B358 Measuring data output Input tool Data input device for spreadsheet software. Others Memory card Stores/recalls the measuring conditions (up to 20), measured data, and statistical data. Memory: 8MB LCD protective sheet For touch panel protection (0 sheet set) SPC connecting cables Connects a control unit with DP-VR. 3'(m): '(2m): DP-VR Performs various statistical processing Reference step specimen Used to calibrate detector sensitivity. Step nominal value: 2µm/0µm.08" (2) 2896 Printer paper Five rolls 984'(25m) Standard paper: Durable paper: " (79) 78-6 (mm) (inch/mm) ø.97" (ø50) (20V) 2.26" (57.5) 3

14 Specifications are subject to change without notice. Note: ll information regarding our products, and in particular the illustrations, drawings, dimensional and performance data contained in this printed matter as well as other technical data are to be regarded as approximate average values. We therefore reserve the right to make changes to the corresponding designs. The stated standards, similar technical regulations, descriptions and illustrations of the products were valid at the time of printing. In addition, the latest applicable version of our General Trading Conditions will apply. Only quotations submitted by ourselves may be regarded as definitive. Mitutoyo products are subject to US Export dministration Regulations (ER). Re-export or relocation of our products may require prior approval by an appropriate governing authority. urora, Illinois (Corporate Headquarters) (630) Westford, Massachusetts (978) Huntersville, North Carolina (704) Mason, urora, Ohio Illinois (Corporate Headquarters) (53) Plymouth, Westford, Michigan Massachusetts (734) Huntersville, North Carolina City of Industry, California (626) Mason, Ohio Kirkland, Plymouth, Washington Michigan (408) City of Industry, California One Number to Serve You Better -888-MITUTOYO ( ) Trademarks and Registrations Designations used by companies to distinguish their products are often claimed as trademarks. In all instances where Mitutoyo merica Corporation is aware of a claim, the product names appear in initial capital or all capital letters. The appropriate companies should be contacted for more complete trademark and registration information. 20 Mitutoyo merica Corporation, urora IL 0-04 Printed in US, January 20