Contents. I. General Information...3. III. Pen Storage and Maintenance...9 IV. Question & Answer...10

Transcription

1 10

2 Contents I. General Information Overview Pen Tablet Functions System Requirements Installing the Driver Software on Windows Hardware Installation Verifying Hardware and Driver Functions Usage Tips...4 II. Driver Interface Introduction Control Interface Digital Pressure Sensitive Pen Settings Key Functions Workspace and Shortcuts Settings Workspace Settings Function Shortcut Function Settings Express Shortcut Function Settings Digital Pen Pressure Sensitivity Test...8 III. Pen Storage and Maintenance...9 IV. Question & Answer...10 *The driver may already be updated to a newer version prior to be packaged. If your installation screen does not match the content of this manual, please refer to your software screen after installation. 2

3 10 10 Screen 3

4 6. Verifying Hardware and Driver Functions 6.1 Follow the steps to verify if the wired tablet is installed properly: *The following picture refer only to TS-6608, the picture of different models will be a difference! LOGO The l 1. Tap on any surface with the tip of the pen, to wake it up if it has gone into standby mode. A built-in power saving function may have forced the pen into the standby mode if either of them is not used for a period of time. 2. As soon as the pen tablet itself activates, the LED will be light briefly, and will then go and stay off again. 3. When the tablet detects the presence of the digital pen, the LED will be blinked slowly. This happens either when pen tip is hovering or placing within the working area which above the tablet. 4. When you press a button on the pen barrel, the LED will be lighted up. 5. Hovering and moving the pen in the working area will cause the cursor on the screen to move accordingly.changing the wireless stylus pen tip Note: After the tablet's device driver has been properly installed, a small tablet icon ( which is normally at the lower right corner of the screen. ) will appear in the system tray, 7. Usage Tips (1) Double tapping When you double tap with the digital pen (equivalent to a double click with a mouse), try to keep the pen tip away from the tablet s surface, or at least try to lift the pen tip as high as possible before the second tap. (2) Storing the digital pen To store the pen, make sure the pen tip does not touch anything, and especially do not let the pen stand in a cup or pen holder with the tip down. Even though the possibility is low, constantly put stress on the pen tip might damage precise configuration of the pen. Place the pen in a pen holder, or turn the pen tip pointing upward or horizontally with the pen tip free of any pressure by other objects. (3) Scrolling function of digital pen The digital pen has the same function of the normal mouse for scrolling pages. Press the first button of the digital pen (same function as mouse s middle click) over the tablet s working area. (4) Using a pen without an ordinary mouse You may install the digital pen, digital mouse, and normal mouse in your computer at the same time and you can also remove them to a different computer as well. However, only one device is able to work at a time. * Do not use more than two devices at the same time in case the screen cursor is jittering or not moving. 4

5 II. Driver Interface Introduction 1. Control Interface When you double click the driver tablet icon ( ) which normally appears in the system tray at the corner of the screen, you will see the control panel (pictured above). It will display driven-related information. Controlling the panel by digital graphic tablet can set up functions for the button of the digital pressure-sensitive pen, regulate the pen s pressure sensitivity and modify the workspace and shortcut keys. 1.1 Digital Pen Pressure Sensitivity Test Click Pen Pressure Test into Pressure Sensitivity Testing 5

6 2. Digital Pressure Sensitive Pen Settings 2.1 Key Functions Above menu shows the defining button of the digital pen. Selecting its left, middle, right, keyboard keys, None Button,Change Brush on the corresponding right drop-down menu of the pen function settings window s the first button, the second button can achieve its functions. When finished the first button and the second button selecting the keyboard keys, all the other keys can be freely defined. When this done, you can achieve all the keys functions of the graphic software. Digital pressure sensitive pen default setting functions: 1.The pen nib is equivalent to the mouse left button function. 2.When the first button is E, you can switch it to eraser in the graphic software(such as photoshop etc.) 3.The second button is equivalent to the mouse right function. 3. Advanced Setting and Shortcuts Settings Click the Advanced Setting button in tablet settings(see the selected area above), you can access the working area and shortcut key settings. 3. Advanced Setting Area A:Soft Keys Area C:Soft Keys function settings area The work area:area A+Area B Full Range The work area:area B Disable Function shortcuts Area B:the work area 6

7 Area A:Soft KEY Area B: The work area Area C: Soft keys setting area has three settings: Disabled function shortcuts keys, enabled function shortcuts keys. the full range of. Disabled soft keys: select this key, the key function will be disabled in the work area. The graphic tablet s work area is limited in the C area. Enabled soft keys: select this key, the soft keys will be enabled in the work area of the graphic tablet. Full Range: full range selected, graphic tablets work area will be expanded to Zone A plus Zone C, soft function is disabled Soft Key Settings Click the key of the soft keys area can enter into soft keys function setting screen (pictured above), the corresponding soft key is from S1-S16 of 16 soft keys. Selecting any soft keys, and then selecting the keyboard keys can setup functions for the selected soft key. 7

8 4. Digital Pen Pressure Sensitivity adiust Pressure sensitivity of the digital pen can be tested in any area of the control panel. The red line of the current pressure value will display different lengths according to the different pressure of the graphic tablet. Pressure sensitivity: move the slider from left to right, it can be used to adjust the sensitivity of the tip and the severity of the stroke when drawing, which affects the change of the handwriting. The Back is completely controlled by the application programming, unrelated to graphic tablets driver programming. When your computer is connected with two screens and use the extended mode, you can choose the corresponding work area of the graphic tablet in the setup screen area(green box area). 8

9 The green LED light on the tablet is the main indicator for hardware operation and depending on your pen tablet model may be located at a different place that shown in the above diagram. This LED normally stays off, and will only turn it on or off in response to various conditions. Watch the state of the LED on the tablet as you go through these test steps: 1. Tap on any surface with the tip of the pen, to wake it up if it has gone into standby mode. A built-in power saving function may have forced the pen into the standby mode if either of them is not used for a period of time. 2. As soon as the pen tablet itself activates, the LED will be light briefly, and will then go and stay off again. 3. When the tablet detects the presence of the digital pen, the LED will be blinked slowly. This happens either when pen tip is hovering or placing within the working area which above the tablet. 4. When you press a button on the pen barrel, the LED will be lighted up. 5. Hovering and moving the pen in the working area will cause the cursor on the screen to move accordingly.changing the wireless stylus pen tip C han gin g th e w ire les s s tylu s p en tip A: Pull out the pen tip from Digital pen by using a Normal Pen Clip B: Push the pen tip into the digital pen, Make sure fit it up to the end properly. 9

10 : 10

11 10