POWER RELAY. FTR-K1-KS Series. 1 POLE - 16A / Inrush 120A relay FTR-K1 SERIES FEATURES

Transcription

1 POWER RELAY POLE - 6A / Inrush 20A relay FTR-K-KS Series FTR-K SERIES FEATURES pole 6A, form A or form C Peak inrush current 20A / TV-8 Coil power 400mW High insulation in small package (between coil and contacts - Insulation distance: mm min. - Dielectric strength: 5,000VAC - Surge strength:,000v UL446 Class F coil insulation wire Cadmium-free contacts for eco-program Flux proof, RTII RoHS compliant Please see page 6 for more information PARTNUMBER INFORMATION FTR-K C K 005 T - KS [Example] (a) (b) (c) (d) (e) (f ) (a) Relay type FTR-K : FTR-K-Series (b) Contact configuration A C : form A : form C (c) Coil type K : Standard (400mW) (d) Coil rated voltage 005 : 5... VDC Coil rating table at page 3 (e) Contact material / TV type T : AgSnO 2 / TV-8 rating (f) Inrush type KS : Inrush 20A type Actual marking does not carry the type name : "FTR" E.g.: Ordering code: FTR-KCK005T-KS Actual marking: KCK005T-KS

2 SPECIFICATION Item FTR-KCK ( ) T-KS FTR-KAK ( )T-KS Contact Data Configuration form C form A Material AgSnO 2 Resistance (initial) Max. 0mΩ at A, 6VDC Contact rating Max. carrying current Max. switching voltage Max. switching power Min. switching load * Max. inrush current 6A, 250VAC 20A 440VAC 4,000VA 0 ma, 5VDC 20A, 250VAC (N.O. contact) Life Mechanical Min. 20 x 6 operations Electrical 20A, 250VAC Resistive load Min. 30 x 3 operations Min. 0 x 3 operations Lamp load (TV-8) Peak inrush (20A 250VAC) Min. 25 x 3 operations (N.O. contact) Min. 30 x 3 operations Coil Data Rated power mW (at 20 degc ) Operate power Operating temperature range 200-2mW -40 C to +85 C (no frost) Timing Data Operate (at nominal voltage) Max. 5ms (without bounce) Release (at nominal voltage) Max. 5ms (no diode, without bounce) Insulation Resistance (initial) Min.,000MΩ at 500VDC Other Dielectric strength Open contacts Contacts to coil,000vac, min. 5,000VAC, min. Surge strength Coil to contacts,000v /.2 x 50µs standard wave Clearance Creepage Vibration resistance Shock Weight Sealing Misoperation μs Endurance Misoperation μs Endurance mm mm Min. 25 x 3 operations Min. 30 x 3 operations to 55 to Hz single amplitude 0.35mm to 55 to Hz single amplitude 0.75mm Min. 0m/s 2 ( ± ms) Min.,000m/s2 (6 ± ms) Approximately 3 g Flux proof RTII * Minimum switching loads mentioned above are reference values. Please perform the confirmation test with actual load before production since reference values may vary according to switching frequencies, environmental conditions and expected reliability levels. 2

3 COIL RATING Coil Code Rated Coil Voltage (VDC) Coil Resistance +/- % (Ohm) Must Operate Voltage (VDC) * Must Release Voltage (VDC) * , , , Rated Power (mw) , , , Note: All values in the table are valid for 20 C and zero contact current. * Specified operate values are valid for pulse wave voltage. SAFETY STANDARDS Type Compliance UL UL 508 (No. E6364) CSA C22.2 No. 4 (No. LR40304) VDE IEC/EN68- EN60065 clause 4.6. EN clause 5.3; 6.3; 29.; 29.2; 29.3 EN clause 2.2; 3.2; 20.; 20.2; 20.3 Contact rating form A type form C type Flammability: UL 94-V0 (plastics) 6A, 277VAC (resistive), 50C TV-8, 20VAC, 50C 6A, 277VAC (resistive) TV-8, 20VAC 6A, 250VAC, cosφ=, 50C 8/20A, 250VAC, 850C 6A, 277VAC (resistive), 50C TV-8, 20VAC, (N.O. contact), 50C 6A, 277VAC (resistive) TV-8, 20VAC (N.O. contact) 6A, 250VAC, cosφ=, 50C 8/20A, 250VAC, 850C (N.O. contact) 3

4 CHARACTERISTIC DATA (For reference only) Coil Temperature Rise Operating Range Maximum Switching Power Temperature rise (degc) A 6A 0A Coil power (W) Nominal voltage multiplying factor 2.5 FTR-K 2 0A 6A.5 Must operate voltage (hot coil) Must operate voltage (cool coil) Ambient Temperature (degc) Switching current (A) FTR-K AC resistive Contact voltage (V) 00 Service Life (x 3 operations) Life Curve 250VAC resistive 250VAC cosφ=0.4 FTR-KAK 250VAC cosφ= Contact current load (A) Service Life (x 3 operations) 00 0 Life Curve 250VAC resistive 250VAC c cosφ=0.7=. FTR-KCK 250VAC cosφ= Contact current load (A) 4

5 DIMENSIONS PC board mounting hole layout (BOTTOM VIEW) Schematics (BOTTOM VIEW) For form A relay, connect terminals to 8 and 2 to 7 on the PC Board. For form C relay, connect terminals to 8, 2 to 7 and 3 to 6 on PC Board. Unit: mm Note: In case of form A, terminals marked are omitted. 5

6 RoHS Compliance and Lead Free Information. General Information All relays produced by Fujitsu Components are compliant with RoHS directive 20/65/EU including amendments. Cadmium as used in electrical contacts is exempted from the RoHS directives. As per Annex III of directive 20/65/EU. All relays are lead-free. Please refer to Lead-Free Status Info for older date codes at: Lead free solder plating on relay terminals is Sn-3.0Ag-0.5Cu, unless otherwise specified. This material has been verified to be compatible with PbSn assembly process. 2. Recommended Lead Free Solder Condition Recommended solder Sn-3.0Ag-0.5Cu. Flow Solder Condition: Pre-heating: maximum 20 C within 90 sec. Soldering: dip within 5 sec. at 255 C ± 5 C solder bath Relay must be cooled by air immediately after soldering Solder by Soldering Iron: Soldering Iron 30-60W Temperature: maximum C Duration: maximum 3 sec. We highly recommend that you confirm your actual solder conditions 3. Moisture Sensitivity Moisture Sensitivity Level standard is not applicable to electromechanical relays, unless otherwise indicated. 4. Tin Whiskers Dipped SnAgCu solder is known as presenting a low risk to tin whisker development. No considerable length whisker was found by our in house test. 6

7 Fujitsu Components International Headquarter Offices Japan Fujitsu Component Limited Shinagawa Seaside Park Tower 9F, 2-4, Higashi-shinagawa 4-chome, Shinagawa-ku, Tokyo, , Japan Tel: (8-3) Fax: (8-3) Web: North and South America Fujitsu Components America, Inc North st Street, Suite 22 San Jose, CA 953, USA Tel: (-408) Fax: (-408) Web: us.fujitsu.com/components Europe Fujitsu Components Europe B.V. Diamantlaan WV Hoofddorp Netherlands Tel: (3-23) Fax: (3-23) Web: emea.fujitsu.com/components/ Asia Pacific Fujitsu Components Asia Ltd. 2E Pasir Panjang Road #0-0 Citilink Warehouse Complex Singapore 8529 Tel: (65) Fax: (65) Web: China Fujitsu Electronic Components (Shanghai) Co., Ltd. Unit 4306, InterContinental Center 0 Yu Tong Road, Shanghai , China Tel: (86-2) Fax: (86-2) fcal@sg.fujitsu.com Web: Hong Kong Fujitsu Components Hong Kong Co., Ltd. Unit 506, Inter-Continental Plaza No.94 Granville Road, Tsim Sha Tsui, Kowloon, Hong Kong Tel: (852) Tex: (852) fcal@sg.fujitsu.com Web: Fujitsu Components Europe B.V. All rights reserved. All trademarks or registered trademarks are the property of their respective owners. The contents, data and information in this datasheet are provided by Fujitsu Component Ltd. as a service only to its user and only for general information purposes. The use of the contents, data and information provided in this datasheet is at the users own risk. Fujitsu has assembled this datasheet with care and will endeavor to keep the contents, data and information correct, accurate, comprehensive, complete and up to date. Fujitsu Components Europe B.V. and affiliated companies do however not accept any responsibility or liability on their behalf, nor on behalf of its employees, for any loss or damage, direct, indirect or consequential, with respect to this datasheet, its contents, data, and information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Nor do Fujitsu Components Europe B.V. and affiliated companies accept on their behalf, nor on behalf of its employees, any responsibility or liability for any representation or warrant of any kind, express or implied, including warranties of any kind for merchantability or fitness for particular use, with respect to these datasheets, its contents, data, information and related graphics and the correctness, reliability, accuracy, comprehensiveness, usefulness, availability and completeness thereof. Rev. August 20, 205 7