LDCDP EPC50ACU.SR6. L force Controls. Ä.SR6ä. Software Manual. Industrial PC. ACU UPS software for Industrial PCs

Transcription

1 LDCDP EPC50ACU.SR6 L force Controls Ä.SR6ä Software Manual Industrial PC ACU UPS software for Industrial PCs

2 Please read these instructions before you start working! Follow the enclosed safety instructions.

3 Validity information These instructions are valid for ƒ ACU UPS software for Lenze Industrial PCs Trademark Windows XP, Windows XP Embedded and Windows Embedded Standard 2009 are registered trademarks or trademarks of Microsoft Corporation in the USA and/or other countries. Any additional trade names given in this documentation are trademarks of their corresponding owners. Document history Material number Version Description /2007 TD29 First edition /2009 TD29 Revision /2010 TD29 Extension by the description of software versions V3.x and V4.x /2012 TD29 Revision of ACU control register.sr /2015 TD09 Extension by the description of software version V5.x 0Fig. 0Tab. 0 Tip! Information and auxiliary devices related to the Lenze products can be found in the download area at 3

4 i Contents 1 Software Description Operating mode System Requirements Messages Message in case of a voltage failure Message after a change in ACU UPS state Software Operation Start and Close Software Open User Interface User Interface Dialogs Registry "ACU State" Show UPS State Registry "ACU Control" Configure UPS Registry "Time Set" Time Before Shutdown Registry "Application" Start External Programs Registry "Shutdown" Force Shutdown Registry "LogFile" View Program Messages Software Installation

5 Software description Operating mode 1 1 Software Description The industrial PC option "ACU UPS Control Unit" in combination with a battery/capacitor pack extends the industrial PC (IPC) by one UPS function.the ACU UPS software controls the behaviour of the IPC in this process as soon as the hardware identifies a supply voltage failure. The ACU UPS control unit is a factory set pre equipment if you chose this option when placing your purchase order. However, it can also be upgraded later on by Lenze service personnel. If you purchased the preinstalled operating system on a storage medium at Lenze, the ACU UPS software is already installed and configured according to your hardware. Alternatively, you can find the software on the driver CD for your IPC. Then, install the software as described in the chapter "Software Installation". ( Operating mode During the boot phase of the operating system, the ACU UPS is in a permanent buffer operation which means that it already provides protection against data loss in the boot phase, even before the ACU software has started. The ACU software starts automatically after the operating system has been booted and monitorsthe voltage supply from the background until it is closed along with the operating system. 1.2 System Requirements Note! Software versions Vx.x must only be used in conjunction with specific devices and are incompatible. ACU UPS version Device Operating system V2.x IPC CPC 2700, EL or CS with ACU UPS control Windows XP or Windows XP Embedded unit V3.x L force Controller 3241 C Windows XP or Windows Embedded Standard 2009 V4.x V5.x IPC CPC 2800, EL or CS with ACU USV Control Unit IPC CPC 2800, EL oder CS mit ACU USV Control Unit Windows XP or Windows Embedded Standard 2009 Windows Embedded Standard 7 P 64bit 5

6 1 Software description Messages Message in case of a voltage failure 1.3 Messages Message in case of a voltage failure In the case of a voltage failure, the ACU UPS takes charge of the IPC supply. The remaining time to the IPC shutdown is displayed on the desktop. ( 14). Fig. 1 1 Desktop message in the event of a voltage failure EPC50ACU Message after a change in ACU UPS state Changes in ACU UPS state are indicated by a change in colour of the ACU symbol on the Windows task bar. Fig. 1 2 Windows task bar with ACU UPS symbol Legend: Green: Battery/capacitor pack loaded and active Yellow: Battery/capacitor pack is being loaded Red: Indicates one or more of the following faults: ACU UPS is buffering the system Short circuit in the battery/capacitor pack Battery/capacitor pack is not connected Battery/capacitor pack is damaged Non defined battery/capacitor packstatus Charging connection of the ACU UPS is defective EPC50ACU 001 6

7 Software operation Start and Close Software 2 2 Software Operation 2.1 Start and Close Software Start After the IPC has been booted, the software starts automatically and then runs in the background. A symbol pops up in the information bar. Fig. 2 1 Windows task bar with ACU UPS symbol EPC50ACU 001 Note! If an L force Controller is delivered with ACU UPS but without a battery pack, the ACU UPS software is installed but UPS support is deactivated. In this case, there will be no ACU symbol in the information bar of the Windows task bar. In the "ACU Control" registry, UPS support can be( 12)activated and deactivated. Double click the ACU symbol in the control panel to start the software manually. Fig. 2 2 Control panel with opened ACU software window (in our example: ACU UPS V3.x) EPC50ACU 011 7

8 2 Software operation Start and Close Software Close Usually, the software is automatically closed by Windows. If you want to close the software manually, right click the ACU symbol in the information bar of the Windows task bar and select Exit from the context menu. Fig. 2 3 Windows task bar with opened context menu EPC50ACU 002 ACU UPS V2.x: UPS functionality is switched off until it is switched on again via the context menu. ACU UPS V3.x/V4.x/V5.x: UPS functionality is switched off until the next system start up. 8

9 Software operation Open User Interface Open User Interface Note! For configuring the ACU software, administrator rights are required. Otherwise, only actual states can be displayed. ƒ If you want to View ACU UPS Configuration, double click the ACU symbol in the information bar of the Windows task bar. The ACU software dialog is displayed. The registries of this dialog show the ACU UPS software settings. Various settings which affect software only can be made (e.g. the period of time from identifying a voltage failure to the shutdown of the IPC). Settings affecting the ACU UPS control unit hardware cannot be made. Fig. 2 4 ƒ Example: ACU software dialog ACU UPS V2.x EPC50ACU 005 If you want to Configure the ACU UPS Control Unit, double click on the ACU symbol in the Windows control panel. The ACU software dialog is also displayed. Unlike the process described above, the ACU control registry is displayed as well which helps you configure the behaviour of the ACU UPS control unit in the case of a voltage failure. Fig. 2 5 Example: ACU software dialog ACU UPS V2.x EPC50ACU 004 Information on the registries of the user interface of the various ACU UPS versions is provided in the following chapter. 9

10 2 Software operation User Interface Dialogs Registry "ACU State" Show UPS State 2.3 User Interface Dialogs Registry "ACU State" Show UPS State ACU USV V2.x: Type Hardware Type Power OK/Fail Input Voltage State; OK or Failure UPS On/Off On: UPS functionality activated Buffer Time [s] s Period of time to wait until a voltage failure is reported by the ACU UPS control unit. Thus, voltage fluctuations are filtered out. Delay Time [s] s; infinite Maximum period of time the industrial PC can be fed by the battery/capacitor pack, depending on the hardware. ACU State Current ACU State Display Firmware Version Displays the current ACU firmware version Note! A change in the UPS State is displayed with a delay. 10

11 Software operation User Interface Dialogs Registry "ACU State" Show UPS State 2 ACU USV V3.x/V4.x/V5.x: Type Hardware Type Power OK/Fail Input Voltage State; OK or Failure UPS On/Off On: UPS functionality activated Delay Time [s] s Period of time to wait until a voltage failure is reported by the ACU UPS control unit. Thus, voltage fluctuations are filtered out. Buffer Time 4 min.; infinite Maximum period of time the industrial PC can be fed by the battery/capacitor pack, depending on the hardware. ACU State Current ACU State Display Firmware Version Displays the current ACU firmware version Note! A change in the UPS State is displayed with a delay. 11

12 2 Software operation User Interface Dialogs Registry "ACU Control" Configure UPS Registry "ACU Control" Configure UPS Note! This registry is only shown when the ACU software has been called up via the system panel. It is not shown when the software is called up by double clicking the symbol in the information bar of the Windows task bar. ACU USV V2.x: Buffer Time [s] s Period of time to wait until a voltage failure is reported by the ACU UPS control unit. Thus, voltage fluctuations are filtered out. Delay Time s; infinite Maximum period of time the industrial PC can be fed by the battery/capacitor pack, depending on the hardware. Restart after Delay Time On/Off On: Restart or shutdown of the system when the delay time is up. UPS Activated On/Off On: UPS support activated Off: UPS support deactivated Auto off after shutdown On/Off On: The ACU UPS control unit is switched off right after the shutdown of the system. This function requires a system with ACPI support (ETX CD). Backlight off after Power Fail On/Off On: Deactivates the backlight of the TFT display in case of a voltage failure. 12

13 Software operation User Interface Dialogs Registry "ACU Control" Configure UPS 2 ACU USV V3.x: Delay Time [s] s Period of time to wait until a voltage failure is reported by the ACU UPS control unit. Thus, voltage fluctuations are filtered out. Buffer Time 4 min.; infinite Maximum period of time the industrial PC can be fed by the battery/capacitor pack, depending on the hardware. UPS Activated On/Off On: UPS support activated Off: UPS support deactivated ACU USV V4.x: Buffer Time [s] s Period of time to wait until a voltage failure is reported by the ACU UPS control unit. Thus, voltage fluctuations are filtered out. Delay Time 4 min.; infinite Maximum period of time the industrial PC can be fed by the battery/capacitor pack, depending on the hardware. Restart after Delay Time On/Off On: Restart or shutdown of the system when the delay time is up. UPS Activated On/Off On: UPS support activated Off: UPS support deactivated Backlight off after Power Fail On/Off On: Deactivates the backlight of the TFT display in case of a voltage failure. 13

14 2 Software operation User Interface Dialogs Registry "Time Set" Time Before Shutdown ACU USV V5.x: Delay Time [s] s Period of time to wait until a voltage failure is reported by the ACU UPS control unit. Voltage fluctuations are therefore filtered out. Buffer Time 4 min.; infinite Maximum period of time the industrial PC can be fed by the battery/capacitor pack, depending on the hardware. Restart On/Off On: Restart or shutdown of the system when the delay time is up. UPS Activated On/Off On: UPS support activated Off: UPS support deactivated Backlight off after Power Fail On/Off On: Deactivates the backlight of the TFT display in the event of a voltage failure Registry "Time Set" Time Before Shutdown ACU UPS Vx.x: Time Before Shutdown s Period of time from identifying a mains failure by the ACU UPS control unit until shutting down the IPC. This period of time must be shorter than the delay time ( 12) plus the period of time needed by the IPC to shut down. Example: The IPC can be supplied for 100 s by the battery pack and needs a maximum of 20 s for a safe shutdown. Delay time = 100 s Time before shutdown = < 80 s 14

15 Software operation User Interface Dialogs Registry "Application" Start External Programs Registry "Application" Start External Programs ACU UPS Vx.x: While the ACU software counts down the seconds until the IPC is shut down after a voltage failure, an external program can be started. Executable Application Path of the executable program file of the application [Browse] Search executable program file Execute Application On/Off On: The program file specified in "Executable Application" is executed Registry "Shutdown" Force Shutdown ACU UPS Vx.x: Shutdown On/Off Default Setting Force Shutdown On/Off If you are using the default setting and an application prompts you to make a user entry when shutting down the PC, the PC cannot be shut down automatically. If the "Force Shutdown" option is activated, all programs are closed before the shutdown without considering feedbacks. Caution: This setting may lead to data loss. 15

16 2 Software operation User Interface Dialogs Registry "LogFile" View Program Messages Registry "LogFile" View Program Messages ACU UPS Vx.x: All ACU software messages are recorded in the ACU.log file and can be viewed there. [Position Log File] Select the folder the ACU.log file shall be written to. [Show Log File] Display ACU.log File Note! The log file data is moved to the "ACU.bak" file when the file size reaches 64 KB so that the log file does not become too big. If you delete the "ACU.log" log file through the Windows Explorer, a new log file will be created as soon as a new log entry is available. It may be impossible to write the log file if the software is run under a user account with restricted access rights and if a folder other than the preconfigured folder has been assigned. So please ensure that the user account has the corresponding write permissions with regard to the log file folder. If a write filter (EWF or FBWF) is used: The log file need not be in a write protected area. 16

17 Software installation 3 3 Software Installation The ACU UPS control unit software is a factory set pre equipment if you chose this option when placing your purchase order and if you obtained the operating system via a Lenze storage medium. In other cases, start the setup program on the program CD and follow the instructions of the setup assistent. Note! After the ACU UPS software has been reinstalled, UPS functionality is deactivated for versions V3.x/V4.x/V5.x and activated for version V2.x. 17

18 12/2015 Lenze Automation GmbH Postfach , Hameln Hans Lenze Str. 1, Aerzen GERMANY HR Hannover B Service Lenze Service GmbH Breslauer Straße 3, Extertal GERMANY (24 h helpline) [email protected] [email protected] LDCDP EPC50ACU.SR6 EN 5.0 TD