Installation Guide for RadioLabs USB Wifi Antennas/Adapters

Transcription

1 1 Installation Guide for RadioLabs USB Wifi Antennas/Adapters

2 2 PLEASE READ BEFORE ATTEMPTING INSTALLATION Thank you for purchasing a RadioLabs USB wireless networking product. This document will guide you through the steps to install the software or drivers necessary for your RadioLabs USB Wifi Antenna or Adapter on your computer. These instructions are for: CaptiFi High Power USB Wifi Antenna WaveRv - Wireless Rv Solution (purchased after June 10 th 2009) Wave Magnum - High Power USB Wifi O2Boost - Directional USB Wifi Antenna The Seed Plug and Go USB Wifi System WaveRv Marine - Wireless Marine System (purchased after May 28 th 2009) O2Connect - High Power Directional USB Panel (purchased after May 28 th 2009) This guide and the included software are not compatible with the WaveRV II Long Range USB Adapter. Please note that you will need a USB 2.0 port to utilize any of the RadioLabs USB Wifi Adapters/Antennas listed above (most newer [post 2004] PC s have USB 2.0 ports as standard equipment). Installation Instructions for Windows PCs The Windows software included in this CD or.zip archive is compatible with the following versions of Windows: Windows 98 SE Windows Me Windows 200 Windows XP Windows Vista (32 & 64-bit*) The screenshots included in this guide are from the Windows XP version of Windows. Please note that things may appear slightly different on your system depending on your version of Windows. However, the installation steps will be similar regardless of your Windows version. *The following instructions are not compatible with Windows 64-bit systems. Drivers are included with this CD or.zip archive for Windows 64-bit systems. However, the installation program and software utility are not compatible with 64-bit systems (i.e. Windows Vista 64-Bit). Instructions for installation are included starting on page. 10

3 3 Note: Do not insert the USB connector for your RadioLabs USB Wifi Antenna/Adapter into your PC until prompted. Before installing your RadioLabs device, you will need to disable or disconnect any wireless devices currently operating on your PC. This includes integrated wireless cards, PCI adapters or external USB adapters. (This step is not necessary on computers running Windows Vista. It is, however, recommended to avoid confusion as to which device s signal you are viewing if using the Connect to a Network function to view and connect to wireless networks) Your PC does not need an existing wireless card or built-in wifi adapter to utilize any RadioLabs USB Wifi Antenna or Adapter. All of RadioLabs USB Wifi Antennas/Adapters have a built-in wireless card that takes the place of your existing wireless network connection. If your PC does not have a switch to disable your internal wireless card or external wifi device to disconnect, you will need to use Network Connections to disable the connection. Windows XP Users: Click Start > Control Panel > Network Connections Windows Vista Users: Click Start or Windows Logo > Control Panel > Network And Sharing Center > Manage Network Connections Once in the Network Connections window, you need to select the Wireless Network Connection, rightclick and select Disable. If you wish to use your internal wireless card in the future, just repeat the above steps and select Enable

4 4 If the Autorun utility has not automatically run, you will need to double-click the setup.exe file in the root or base directory of this CD or.zip archive. This will run the InstallShield Installation Utility and install the RadioLabs USB Wireless LAN Utility and Driver for your RadioLabs USB Wifi Adapter or Antenna. Select your preferred language and click Next Select Next to continue the installation.

5 5 Click Install to begin installing the RadioLabs Wireless USB Utility Wait for the installation wizard to load

6 6 Click Continue Anyway to continue installation. (Programmer s Note: This software will not impair the correct operation of your system) Installshield is now installing the necessary drivers. Select Finish to complete the driver installation. At this point, the RadioLabs Wireless USB Utility has been installed. You can now insert the USB connector on your RadioLabs USB Wifi Adapter/Antenna into your PC s USB port.

7 7 (If you have the Wave Magnum High Power USB Wifi Adapter, you will need to connect the Mini-B USB end of the included cable to the Wave Magnum and then connect the larger USB connector to your PC s USB port.) This may (depending on your operating system) trigger a Found New Hardware Wizard which will prompt you to install drivers specific for your device. If this does not appear, please skip to page 9. Select No, not this time and click Next Select Install from a list of specific location (Advanced) and click Next

8 8 Make sure that Search for the best driver in these locations and Include this location in the search are selected, and then click Next The driver software is being installed Click Continue Anyway to continue installation.

9 9 The wizard is completing the installation. The wizard has finished installing your driver software and your RadioLabs USB Wifi Adapter/Antenna is ready to use. Click Finish to complete the installation and close the Found New Hardware wizard. Your RadioLabs USB Wifi Adapter or Antenna is now installed and ready to use. Please refer to the RadioLabs USB Device User Manual for instructions on how to use the RadioLabs Wireless USB Utility.

10 10 Installation Instructions for Windows Vista 64-bit - Do not run the setup.exe installation program. The software utility is not compatible with 64-bit systems. This installation can be done two ways. 1. If you have an existing internet connection on the computer on which you are installing the RadioLabs unit, make sure you are connected to the internet and follow the instructions below. a. Plug the USB connector into an available USB 2.0 port on your PC (If you have the Wave Magnum, insert the small end of the black USB cable into the Wave Magnum and the other larger end into the USB port on the PC) b. A Found New Hardware wizard will appear and ask if you want to Locate and Install Driver Software. Select this option. c. Select the Install Driver Software Automatically and if prompted, allow the Windows to search online for drivers. d. The wizard will automatically download and install the correct drivers for your RadioLabs USB Wifi Adapter or Antenna. e. Once finished, your adapter/antenna is ready to use. You can use the Windows Connect/Disconnect utility (in the system tray) to select and connect to available wireless signals.

11 11 2. If you do not have an internet connection on the PC, you can still install your RadioLabs USB Wifi Adapter/Antenna by following the below instructions. However, depending on your security settings, your system may not accept the non-native drivers included in this CD or.zip archive. If this is the case, please connect the computer to the internet and follow the above instructions. a. Plug the USB connector into an available USB 2.0 port on your PC (If you have the Wave Magnum, insert the small end of the black USB cable into the Wave Magnum and the other larger end into the USB port on the PC) b. A Found New Hardware wizard will appear and ask if you want to Locate and Install Driver Software. Select this option. c. Select the Install Drivers from a Specific Location option d. When prompted to locate the drivers, select your CD drive (i.e. D:/), select the RadioLabs Universal Driver folder, select the RTL8187 folder and select the Vistax64 folder and click OK e. The wizard will automatically install the necessary drivers for your antenna or adapter. f. Once finished, your adapter/antenna is ready to use. You can use the Windows Connect/Disconnect utility (in the system tray) to select and connect to available wireless signals.