Install the SDT200/SDT270 USB driver
|
|
- Madison Hancock
- 8 years ago
- Views:
Transcription
1 Install the SDT200/SDT270 USB driver Install the SDT200/SDT270 driver in windows XP Install the SDT200/SDT270 driver in Windows 7 or Vista Install the SDT200/SDT270 driver in Windows XP Please note: you need administrative rights on the computer Before installing the SDT200/SDT270 USB driver, one of these softwares should already be installed on the computer: SDT270 Updater, DataDump, or Ultranalysis Suite. If this is not the case, please install the required software first. If you only need to update or upgrade the SDT270 device you can install the SDT270 Updater software. It is unwanted to install SDT DataDump or Ultranalysis Suite if this has not been advised to you by an SDT representative. Step 1: Turn on the SDT200/SDT270 device. Wait until the device has booted up and the main measurement screen is loaded. Step 2: Connect your device with the mini USB/USB cable to your PC. Step 3: Driver installation: 3.a) Automatically start driver installation After you ve connected the device, the computer may automatically show the window Found new hardware wizard : If this window does NOT appear: è continue with step 3.b) If it does appear: è Select the last option ( No, not this time ) and click the Next' button è continue with step 3.c). 3.b) Manually start driver installation (follow this step only if the add hardware wizard is not started automatically, otherwise go to step 3.c) è Open the device manager:
2 Click the Start button Click ( Settings ) Control Panel Double click System Click tab Hardware Click Device Manager è In the tree, open the node Network adapters è The list should contain the option RNDIS/Ethernet Gadget, probably with a yellow exclamation mark in front. è Right click the option RNDIS/Ethernet Gadget and click Update driver... è Select the last option ( No, not this time ) and click Next to continue. 3.c) Actual driver installation After following previous step(s), you should see following window:
3 è Select the second option ( Install from a list or specific location ) and click Next You should now see following window: Deselect 'Search removable media' and select "Include this location in the search". Click the ''Browse'' button and select the folder Resources\Drivers of your SDT software. If you use Ultranalysis Suite, browse to "C:\Program Files\SDT\Ultranalysis Suite\Resources\Drivers" or your install path. If you use DataDump, browse to ''C:\Program Files\SDT\SDT270 Data Dump\Resources\Drivers'' or your installation path. If you use Updater, browse to ''C:\Program Files\SDT\SDT270Updater\Resources\Drivers'' or your installation path. Click ''Next''. You will see the following screen:
4 Choose ''Continue Anyway''. You will see the following screen: When the installation process is finished, you will see the following screen:
5 Click ''Finish''. The installation is completed and confirmed by the following message: In Windows XP, the driver needs to be installed for each USB port the SDT200/SDT270 device will be connected to. It is advised to install the SDT200/SDT270 driver on these other ports now, to avoid having to do it later: è Shut down the SDT200/SDT270, disconnect it from the current USB port and repeat above steps for the other USB ports. Install the SDT200/SDT270 driver in Windows 7 or Vista Please note: you need administrative rights on the computer Before installing the SDT200/SDT270 USB driver, one of these softwares should already be installed on the computer: SDT270 Updater, SDT270 DataDump, or Ultranalysis Suite. If this is not the case, please install the required software first. If you only need to update or upgrade the SDT270 device you can install the SDT270 Updater software. It is unwanted to install SDT DataDump or Ultranalysis Suite if this has not been advised to you by an SDT representative. Step 1: Turn on the SDT200/SDT270 device. Wait until the device has booted up and the main measurement screen is loaded. Step 2: Connect your device with the mini USB/USB cable to your PC. Step 3: Driver installation: 3.a) Automatically start driver installation After you ve connected the device, the computer may automatically show the window Found new hardware wizard : If this window does NOT appear: è continue with step 3.b) If it does appear:
6 è click the Next' button è continue with step 3.c). 3.b) Manually start driver installation (follow this step only if the add hardware wizard is not started automatically, otherwise go to step 3.c) è Open the device manager: Click the Start button Click Devices and Printers Look for the device RNDIS/Ethernet Gadget right click it and click Properties : Click tab Hardware :
7 Click Properties : Click Change settings :
8 Click Update Driver... : 3.c) Actual driver installation After following previous step(s), you should see following window:
9 è Choose the second option ( Browse my computer for driver software ) You should now see following window: è Click the ''Browse'' button and select the folder Resources\Drivers of your SDT software. If you are using a 32 bit version of Windows 7 or Vista: if SDT270 Updater was installed: C:\Program Files\SDT\SDT270Updater\Resources\Drivers if Ultranalysis Suite was installed: C:\Program Files\SDT\Ultranalysis Suite\Resources\Drivers if SDT270 Data Dump was installed: C:\Program Files\SDT\SDT270 Data Dump\Resources\Drivers If you are using a 64 bit version of Windows 7 or Vista: if SDT270 Updater was installed: C:\Program Files (x86)\sdt\sdt270updater\resources\drivers if Ultranalysis Suite was installed: C:\Program Files (x86)\sdt\ultranalysis Suite\Resources\Drivers if SDT270 Data Dump was installed: C:\Program Files (x86)\sdt\sdt270 Data Dump\Resources\Drivers è Windows will give a safety warning, which you can safely ignore. So click ''Install this driver software anyway''.
10 è Finally, Windows will start the driver installation: è After the installation, click the ''Close'' button. Now your computer should be ready to connect to SDT200/SDT270 devices:
Installation Instructions for 9555 USB Driver
Prior to using the data modem features of your 9555 handset; you must first install the VCOMPORT 9555 USB Driver. This driver is compatible with: Windows XP Service Pack 2, Windows 2000 Service Pack 4,
More informationMidland BT Updater BTUpdater Program Program file (x86) ), Midland
Midland BT Updater After you downloaded the BT Updater setup application from the web site, double click on it and follow the installation procedure. The BTUpdater application is automatically installed
More informationFirmware & Software update procedures Amicroe TouchTAB IV.
Firmware & Software update procedures Amicroe TouchTAB IV. Important note: The steps & procedures outlined below may be of assistance if you are experiencing difficulties with your Amicroe TouchTAB 9.7
More informationAIM SOFTWARE AND USB DRIVER INSTALLATION PROCEDURE
AIM SOFTWARE AND USB DRIVER INSTALLATION PROCEDURE CONTENTS AIM software and USB Driver installation Chapter 1 Installing AIM software and AIM USB driver... 2 Chapter 2 Installation under Microsoft Windows
More informationUSB DRIVER INSTALLATION GUIDE
USB DRIVER INSTALLATION GUIDE Use these instructions to install the USB drivers and Microsoft synchronization software for your Pathfinder 6057 printer. You need these utilities for your printer and computer
More informationUSB Drivers Getting Started Guide
USB Drivers Getting Started Guide PC version US Edition TP-1522-US Issue 2 All rights reserved All information contained in this document is subject to change without notice. Any use of the contents of
More informationInstallation Instructions
Installation Instructions Windows USB driver for Installation If a Diagnostic Interface with USB is connected to a PC with a Windows operating system 98, ME, XP or Vista for the first time, it is necessary
More informationSelect Correct USB Driver
Select Correct USB Driver Windows often installs updated drivers automatically, and defaults to this latest version. Not all of these drivers are compatible with our software. If you are experiencing communications
More informationPL2303HXA/XA Windows 8 Update Driver Installation. How to Update Driver to Support PL2303HXA/XA in Windows 8 Operating Systems
How to Update Driver to Support PL2303HXA/XA in Windows 8 Operating Systems Requirements USB Device with embedded PL2303HX (Rev A) or PL2303X (Rev A) chip version Driver Installer & Build date: 1.5.0 (10/21/2011)
More informationEngineering Note. Correcting Device Driver Issues Product Affected: SpectraSuite, OceanView, OmniDriver, SPAM Software Date Issued: 3/16/2015.
Engineering Note Topic: Correcting Device Driver Issues Product Affected: SpectraSuite, OceanView, OmniDriver, SPAM Software Date Issued: 3/16/2015 Overview If you connect your Ocean Optics USB or PCI
More informationUSA MOBILITY CABLE CONNECTION AND SOFTWARE DRIVER INSTALLATION INSTRUCTIONS. For. Unication M90 Device USB To RS232 Adapter TABLE OF CONTENTS
USA MOBILITY CABLE CONNECTION AND SOFTWARE DRIVER INSTALLATION INSTRUCTIONS For Unication M90 Device USB To RS232 Adapter TABLE OF CONTENTS SECTION 1: ADAPTER CABLE CONNECTION INSTRUCTIONS... 2 SECTION
More information3. USB DRIVER. 3-1. Installation of USB driver. 3-1-1. Driver for Infinity SD Data Logger. INFINITY Series Acquisition Tools Manual
3. USB DRIVER 3-1. Installation of USB driver Before you launch this software, the driver should be once surely registered. Access between the instrument and a PC through the USB cable supplied by us as
More informationUSB DRIVER INSTALLATION GUIDE
USB DRIVER INSTALLATION GUIDE Use these instructions to install the USB and Microsoft ActiveSync synchronization software for your Monarch Pathfinder Ultra Platinum 6039 printer and computer to communicate.
More informationImportant Note Regarding Your Blu ray Drives
Important Note Regarding Your Blu ray Drives Use these supplemental instructions to complete the setup of your unit Your Disc Publisher unit uses esata to connect the Blu-ray drive(s) to the computer.
More informationEasyGate UMTS Data quick installation guide
EasyGate UMTS Data quick installation guide This installation guide can be used for easy drivers installing, modem configuration a Internet options settings using EasyGate UMTS Data. Inserted screenshots
More informationPCLinq2 Hi-Speed USB Bridge-Network Cable. Quick Network Setup Guide
PCLinq2 Hi-Speed USB Bridge-Network Cable Congratulations! Quick Network Setup Guide For Windows 98/ME/2000/XP Congratulations for installing the PCLinq2 Hi-Speed USB Bridge-Network Cable. This Quick Network
More informationUSB device driver installation for the weatronic update cable and the TX-Module
USB device driver installation for the weatronic update cable and the TX-Module Index 1. Information about the USB connection 1 2. Installation of the USB driver 1 2.1 Installation of the USB driver for
More informationUSB Driver Installation for Windows XP
USB Driver Installation for Windows XP USB Serial Converter Driver Installation for Windows XP CAUTION: You must use the drivers on the CD-ROM supplied with your USB Device. DO NOT download drivers from
More informationCenturion PLUS CPC4 Download Guide
Centurion PLUS CPC4 Download Guide using C4 File Transfer Utility. 1010537 03 01 10 Section 50 1.0 Background: 1.1 The Centurion PLUS Control system consists of a Centurion PLUS Core (CPC4 1) and Color
More informationUSB Driver Installation
USB Driver Installation EPOS Positioning Controllers Edition April 2012 Positioning Controllers USB Driver Installation Document ID: rel3137 maxon motor ag Brünigstrasse 220 P.O.Box 263 CH-6072 Sachseln
More informationUSB Driver Installation
USB Driver Installation EPOS2 Positioning Controllers Edition April 2010 Positioning Controllers USB Driver Installation maxon motor ag Brünigstrasse 220 P.O.Box 263 CH-6072 Sachseln Phone +41 (41) 666
More informationHow to install USB driver (MICRO/I)
How to install USB driver (MICRO/I) HG2G-5S 1. The HG2G-5S USB driver installation wizard will start when Automation Organizer installation is complete. Click the Next button. 2. Read the license agreement
More informationCLEARONE DOCUMENT 801-000-002 (REVISION 1.0) October, 2008. with Converge Pro Units
APPLICATION NOTES Converge Pro Products CLEARONE DOCUMENT 801-000-002 (REVISION 1.0) October, 2008. Troubleshooting USB Connections with Converge Pro Units Description This document explains how to connect
More informationColorfly Tablet Upgrade Guide
Colorfly Tablet Upgrade Guide (PhoenixSuit) 1. Downloading the Firmware and Upgrade Tool 1. Visit the official website http://www.colorful.cn/, choose 产 品 > 数 码 类 > 平 板 电 脑, and click the product to be
More informationThunderMax TMaxI Tuner Software USB Driver Installation Guide for Windows Operating Systems v.100405
ThunderMax TMaxI Tuner Software USB Driver Installation Guide for Windows Operating Systems v.100405 INDEX PAGE 1. USB Driver Installation Guide for Windows XP Page 03 2. USB Driver Installation Guide
More informationTitle: ZOLL USB Direct Connect Cable Installation Instructions
ZOLL USB Direct Connect Cable Installation Instructions Document Status: Released Document #: 48x126-ZOLL-003 Page 1 of 7 Revision History DATE REV REASON January 9, 2008 A Initial Release August 12, 2008
More informationSupplemental USB Driver Installation Guide
Windows 2000/XP/Vista/7 Installation Supplemental USB Driver Installation Guide 1) Do not plug in your Auterra USB OBD Adapter until after the driver is installed. 2) The USB driver is located on the your
More informationIVS-Basic 4.4 IVS-Professional 4.4 IVS-PowerPoint 1.1
Manual IVS-Basic 4.4 IVS-Professional 4.4 IVS-PowerPoint 1.1 Supplement connecting USB RF-II Base Station 1213 2 Contents Contents... 3 Connecting the RF-II Base Station to the USB port... 4 Using the
More informationCommunication with BushingGard using computer USB port
Communication with BushingGard using computer USB port There are two ways of communication with BushingGard through computer USB port: Direct communication between computer USB port and BushingGard USB
More informationThuraya XT-DUAL. Software Upgrade Manual
Thuraya XT-DUAL Software Upgrade Manual Version 1 / February 2012 1. INTRODUCTION... 3 2. SOFTWARE UPGRADE WITH WINDOWS 7... 4 2.1 Installation of the Upgrader Package... 4 2.2 Manual detection (optional
More informationGuide to Installing BBL Crystal MIND on Windows 7
Guide to Installing BBL Crystal MIND on Windows 7 Introduction The BBL Crystal MIND software can not be directly installed on the Microsoft Windows 7 platform, however it can be installed and run via XP
More informationHow To Upgrade A Yarvik Gotab Tablet To Android 4.0 (For Android) 4.2.2 (For Ipad) 4Th Generation (For Microsoft) 4S) 4G (For Zemmer) 4
TAB420/424/460/461/464 GOTAB XERIOS 10 TABLET ANDROID 4.0 UPGRADE INSTRUCTIONS Page 1 of 9 BEFORE YOU START: BACKUP IMPORTANT DATA! Upgrading your Yarvik tablet to Android 4.0 will erase all user settings,
More informationWindows 7 Printer Driver Installation procedure
Windows 7 Printer Driver Installation procedure This is to explain how to install Windows Vista printer driver for Mitsubishi digital printer to Windows 7. * Although CP9550D/DW is shown through this document,
More informationCANON FAX L360 SOFTWARE MANUAL
CANON FAX L360 SOFTWARE MANUAL Before You Begin the Installation: a Checklist 2 To ensure a smooth and successful installation, take some time before you begin to plan and prepare for the installation
More informationInstalling the Driver of your Plotter- / Engraver
Installing the Driver of your Plotter- / Engraver By installing your plotter / engraver software the driver for your device will be pre-installed. When the device is switched on after the software setup,
More informationTAB08-201-3G XENTA 8c 8 3G TABLET FIRMWARE UPGRADE INSTRUCTIONS
TAB08-201-3G XENTA 8c 8 3G TABLET FIRMWARE UPGRADE INSTRUCTIONS Page 1 of 9 BEFORE YOU START: BACKUP IMPORTANT DATA! Upgrading your Yarvik tablet will erase all user settings, user installed applications
More informationInstallation Manual LATC-W1
Installation Manual PRODUCT NAME Controller Setting Software MODEL / Series / Product Number LATC-W1 [Before using this product] Read the "End-User License Agreement" shown on the next page carefully and
More informationHow to install USB driver (MICRO/I)
How to install USB driver (MICRO/I) Install on Windows XP 1. Connect the USB port on HG3G series and the USB port on PC. 2. Windows displays Found new Hardware Wizard. Select No, not this time and press
More informationPrinter Sharing of the PT-9500pc in a Windows Environment
Printer Sharing of the PT-9500pc in a Windows Environment This procedure is for configuring the PT-9500pc as a shared printer in Microsoft Windows. For printer sharing to operate correctly, please be sure
More informationInstalling the USB driver for Firmware 7 or later For use with E-blocks programmer boards and PICmicro Development boards.
Installing the USB driver for Firmware 7 or later For use with E-blocks programmer boards and PICmicro Development boards. Matrix Multimedia USB PICmicro programmer boards with Firmware version 7 or later
More informationActon Research Technical Support SpectraPro Diagnostic Procedure
Acton Research Technical Support SpectraPro Diagnostic Procedure Table of Contents Introduction to the Acton Research Technical Support SpectraPro Diagnostic Procedure...1 Checking the USB Drivers...2
More informationConfiguring Windows 7 64 bit for AutoVISION
This document will describe how to configure a 64 bit version of Windows 7 Professional, Ultimate or Enterprise to utilize the Windows XP Mode (Virtual PC) capabilities to allow AutoVISION to be used in
More informationJTAGjet. series SIGNUM SYSTEMS CORPORATION. USB 2.0 Driver for JTAGjet and ADM51. Installation Instructions
JTAGjet series SIGNUM SYSTEMS CORPORATION USB 2.0 Driver for JTAGjet and ADM51 Installation Instructions COPYRIGHT NOTICE Copyright (c) 2011 by Signum Systems Corporation. All rights are reserved worldwide.
More informationCOPYRIGHT TOP NOTCH TABLETS LLC. 2012. HOW TO: Install the Drivers to your PC so you can Flash Firmware to your RK3066 Powered Tablet.
HOW TO: Install the Drivers to your PC so you can Flash Firmware to your RK3066 Powered Tablet. 1. Inside the RKBatchTool1.5en folder you will see a sub folder called Driver 2. Inside of that folder are
More informationUSB TO UART DRIVER INSTALLATION INSTRUCTIONS FOR EAGLE FIRMWARE VERSION 2.XXX
USB TO UART DRIVER INSTALLATION INSTRUCTIONS FOR EAGLE FIRMWARE VERSION 2.XXX All files mentioned in this document are located at the Model 599 section of the Transceiver Downloads web page on the TEN-TEC
More informationXConsole GUI setup communication manual September 2010.
XConsole GUI setup communication manual September 2010. XConsole is compatible with Microsoft XP, Vista and Windows 7. The software will also work if using Boot camp on a Mac. IMPORTANT NOTES: - Do NOT
More informationPP8X Printer Driver Installation Instruction
PP8X Printer Driver Installation Instruction Pinnacle Technology Corp. CONTENTS 1 BT Device Installation... 1 2 Printer Driver Installation... 6 3 How to Know the Connecting Port... 10 4 How to Configure
More informationThe FlexiSchools Online Order Management System Installation Guide
The FlexiSchools Online Order Management System Installation Guide FlexiSchools May 2012 Page 1 of 18 Installation Pack Welcome to the FlexiSchools system. You will have received a disc containing: Sato
More informationInstallation Notes for Prolific PL-2303 USB Driver for USB - RS232 Adaptor Cable 1. Uninstall Existing USB-Serial Adaptor Drivers
41 Vine Street Magill SA 5072 Phone: 08 8332 9044 Fax: 08 8332 9577 mea@mea.com.au Installation Notes for Prolific PL-2303 USB Driver for USB - RS232 Adaptor Cable 1. Uninstall Existing USB-Serial Adaptor
More informationUpgrading Your PhoneTree Software
Upgrading Your PhoneTree Software For PhoneTree 2100/2500/3500, VoiceWave Series, Patient/Dental/Veterinary Messaging, and HealthWave models upgrading from 6.12.80 or older to 6.13 or newer Question: How
More informationNOTE: PLEASE DO NOT ATTEMPT TO INSTALL THE SOFTWARE BEFORE READING THIS DOCUMENT.
INLINE 5 Software INSTALL BULLETIN Page 2: Installing INLINE 5 Page 6: Removing INLINE 5 NOTE: PLEASE DO NOT ATTEMPT TO INSTALL THE SOFTWARE BEFORE READING THIS DOCUMENT. IMPROPER INSTALLATION OR USE CAN
More informationHow do I configure the wireless printer using a USB or Ethernet cable and install the printer driver in Windows?
How do I configure the wireless printer using a USB or Ethernet cable and install the printer driver in Windows? STEP I: Gather the wireless network settings of your wireless access point or wireless router
More information[Setup procedure for Windows 95/98/Me]
[Setup procedure for Windows 95/98/Me] a. One Print Server. b. One external AC power adapter. c. One setup CD. (For Windows 95/98/Me/NT/2000/XP). d. One user s manual (included quick guide). a. Turn off
More informationInstallation Guide for RadioLabs USB Wifi Antennas/Adapters
1 Installation Guide for RadioLabs USB Wifi Antennas/Adapters 2 PLEASE READ BEFORE ATTEMPTING INSTALLATION Thank you for purchasing a RadioLabs USB wireless networking product. This document will guide
More information1 Installation. Note: In Windows operating systems, you must be logged in with administrator rights to install the printer driver.
Installation A printer driver is an application that manages communication between a printer and your computer. Once installed, the printer driver settings must be configured in the printer Properties
More informationCODESOFT Installation Scenarios
CODESOFT Installation Scenarios NOTES: CODESOFT is a separate install from existing versions of CODESOFT. You will need to make note of your current settings (default directories, etc.) so you can duplicate
More informationTransferring Scans from your Dolphin into Destiny
Transferring Scans from your Dolphin into Destiny Summary: This article is intended to provide Destiny users with an overview of the following tasks 1. Downloading the Dolphin Transfer Utility to their
More informationThe procedure how to keep Microtek scanners to work under Windows Vista system
The procedure how to keep Microtek scanners to work under Windows Vista system Date : July / 01 / 2009 1. For those Microtek scanner models which did not get approved driver of Windows Vista from Microsoft,
More informationSOFTWARE INSTALLATION INSTRUCTIONS
AUDITGARD LGA Electronic Combination Lock SOFTWARE INSTALLATION INSTRUCTIONS Implementation Package The AuditGard Software implementation package includes: 707013 AuditGard Software Install CD 42145 Programming/Audit
More informationShearwater Research Dive Computer Software Manual
Shearwater Research Dive Computer Software Manual Revision 1.3 Table of Contents 1. Basic overview of components 2. O/S IrDA driver installation 2.1 USB IrDA installation for Windows XP Home/Pro editions
More informationUSB Driver Installation Manual [Windows Vista/Windows 7]
USB Communication Converter COM-K USB Driver Installation Manual [Windows Vista/Windows 7] NOV. 2010 R RKC INSTRUMENT INC. IMT01D10-E1 NOTICE This manual assumes that the reader has a fundamental knowledge
More informationInstallation of the USB to RS 485 Converter
Installation of the USB to RS 485 Converter Contents CONTENTS 1 GENERAL INSTRUCTIONS 1 HINT 1 INSTALLATION USING SETUP EXECUTABLE (RECOMMENDED INSTALLATION PROCEDURE) 2 INSTALLATION BY PLUGGING IN THE
More informationScanShell.Net Install Guide
ScanShell.Net Install Guide Please install the software first - DO NOT PLUG IN THE SCANNER The scanner has been carefully packaged to avoid damage during transportation. Before operating the scanner, please
More informationPage 1 S5.5 Monitoring Software Manual Rev 1.2 for Software Ver 1.0
Trantec S5.5 Monitoring Software Manual Initial Setup Minimum PC Requirements 1.6 GHz CPU, 256 MB Memory, 1 available USB port, Windows XP Recommended PC >2.0 GHz CPU, 512 MB (XP) 1 GB (Vista) memory,
More informationOctober 2011 3726 07897 601 Rev. B Page 1
Upgrading Polycom SoundStation2W software to Version 1.607 and CVM to Version 1.85 Installer for Microsoft Windows Vista and Windows 7 (32 and 64 bit) Operating Systems NOTE: Two versions of upgrader are
More informationUSB drivers V1.75 Installation manual USB drivers V1.75 - installation manual Page
USB drivers V1.75 Installation manual USB drivers V1.75 - installation manual Page 1/17 Table of Contents Notes 3 Driver installation for ebro USB device drivers 3 Step 1: Launching the installation program
More informationThe FlexiSchools Online Order Management System Installation Guide
The FlexiSchools Online Order Management System Installation Guide FlexiSchools May 2012 Page 1 of 16 Installation Pack Welcome to the FlexiSchools system. You will have received a disc containing: Sato
More informationPrint Server Application Guide. This guide applies to the following models.
Print Server Application Guide This guide applies to the following models. TL-WR842ND TL-WR1042ND TL-WR1043ND TL-WR2543ND TL-WDR4300 CONTENTS Chapter 1. Overview... 1 Chapter 2. Before Installation...
More informationENPS-MF1. 1 USB Port. Multifunctional Print Server. Quick Installation Guide V1.0
ENPS-MF1 1 USB Port Multifunctional Print Server V1.0 Specifications or features are subject to change without prior notice. All brand names or trademarks are the property of their respective owners. Packing
More informationCOBRA 18R2 Wired Reprogramming Instructions
COBRA 18R2 Wired Reprogramming Instructions The purpose of this document is to perform a wired reprogram of an 18R2 using the COBRA wired reprogrammer. Please note that this process requires only a wired
More informationTroubleshooting Sprint Mobile Broadband USB Modem by Novatel Wireless TM (Ovation TM U727)
Troubleshooting Sprint Mobile Broadband USB Modem by Novatel Wireless TM (Ovation TM U727) If you are unable to resolve your issue using the Troubleshooting steps below, please contact Sprint Customer
More informationSheevaPlug Development Kit README Rev. 1.2
SheevaPlug Development Kit README Rev. 1.2 Introduction... 3 Flow to use the Software Development Kit packages... 3 Appendix A... 5 GCC cross-compiler... 5 Appendix B... 6 Mini-USB debug driver installation
More informationhttp://www.heitel.com/en/service/downloads/?dir=01-demosoftware/01-camcontrollite#01-demosoftware
Technical Product Information No. 14.01 Product/Version CamDisc SVR, CamTel SVR und Cam4mobile, CamDisc SVR 10s, CamDisc SVR 4s, CamServer 1, CamServer 2c und CamServer 2, CamDisc HNVR, CamServer VG 2c/4c,
More informationCOMBOGARDPRO. 39E Electronic Combination Lock SOFTWARE INSTALLATION INSTRUCTIONS
COMBOGARDPRO 39E Electronic Combination Lock SOFTWARE INSTALLATION INSTRUCTIONS IMPLEMENTATION PACKAGE The ComboGard Pro Software implementation package includes: 707012 ComboGard Pro Software Install
More information3M Occupational Health and Environmental Safety 3M E-A-Rfit Validation System. Version 4.2 Software Installation Guide (Upgrade) 1 P age
3M Occupational Health and Environmental Safety 3M E-A-Rfit Validation System Version 4.2 Software Installation Guide (Upgrade) 1 P age Contents Important Information Read First... 3 Software Download...
More informationDigitalPersona Pro Server for Active Directory v4.x Quick Start Installation Guide
DigitalPersona Pro Server for Active Directory v4.x Quick Start Installation Guide 1 of 7 DigitalPersona Pro Server for Active Directory v4.x Quick Start Installation Guide Process Overview Step Description
More informationLPR for Windows 95/98/Me/2000/XP TCP/IP Printing User s Guide. Rev. 03 (November, 2001)
LPR for Windows 95/98/Me/2000/XP TCP/IP Printing User s Guide Rev. 03 (November, 2001) Copyright Statement Trademarks Copyright 1997 No part of this publication may be reproduced in any form or by any
More informationEDMS Operation Manual. 1. Install the USB Driver. 1.3 Click next
EDMS Operation Manual 1. Install the USB Driver 1.1 If this is your first time using the gauge, when you connect the gauge to the PC, a driver installation window may appear or the driver will install
More informationEPSON Stylus COLOR 740. USB Software Installation Guide (Windows 98/iMac ) USB Setup Guide (imac)
EPSON Stylus COLOR 740 TM USB Software Installation Guide (Windows 98/iMac ) USB Setup Guide (imac) This guide includes USB setup instructions for your imac computer, as well as software installation instructions
More informationVirtual COM Port Driver Installation Manual
Virtual COM Port Driver Installation Manual Installing the virtual COM port driver software on a computer makes possible CAT communication via a USB cable to the FT-991 transceiver. This will allow computer
More informationUSB Driver. Installation Manual
USB Driver Installation Manual Issue 1.00 Detailed guide for the installation of Actisense USB Drivers under the following operating systems: Windows XP / 2000 Windows Vista USB Driver Installation Manual
More informationUSB DRIVER INSTALLATION GUIDE
USB DRIVER INSTALLATION GUIDE Thank you for using the Icom Download Service. Please read this installation guide before installing the USB driver into your PC that is connected to the USB (Universal Serial
More informationDRIVERS INSTALLATION GUIDE
1M23Z00902 USB INTERFACE DRIVERS INSTALLATION GUIDE * These CIU-2 drivers are for windowsvista/xp/2000 use, and is not compatible with other OS. Downloaded ZIP extraction (decompression)...p2 Extraction
More informationInstallation of USB Virtual COM. Version 1.02
Installation of USB Virtual COM Version 1.02 RELEASE NOTES Version Date Notes 1.02 May 13, 2014 Modified: Install USB Virtual COM Drivers files on CD updated 1.01 Dec. 10, 2009 Supports driver for Windows
More informationJUNGO driver Installation Manual. for. CAS Interface 2 and Dynamite
JUNGO driver Installation Manual for CAS Interface 2 and Dynamite English - 16 September 2004-1 New USB driver - JUNGODriverXXX This new driver offers a superior compatibility with all Windows operating
More informationSCU-18 PC Connection Cable Driver Installation Manual
SCU-18 PC Connection Cable Driver Installation Manual Installing the SCU-18 PC Connection Cable driver software on a computer makes possible data transmission and updating the transceiver firmware. Please
More informationVirtual COM Port Driver Installation Manual
Virtual COM Port Driver Installation Manual Installing the virtual COM port driver software on a computer makes possible CAT communication via a USB cable to the SCU-17 or an enabled transceivers. This
More informationCMP-102U. Quick Installation Guide
CMP-102U Quick Installation Guide V1.0 http://www.cnet.com.tw 1 CMP-102U Supports One High-speed USB2.0 Port MFP Server Supports 10/100Mbps Fast Ethernet Network Quick Installation Guide 1 Package Contents:
More informationRead Me UNISTREAM AUTOMATION IDE
Read Me UNILOGIC SOFTWARE UNISTREAM AUTOMATION IDE Unitronics UniLogic software is the programming Integrated Development Environment (IDE) you use to configure hardware, communications, and develop both
More informationInstall USB drivers on Windows
Install USB drivers on Windows Any information contained in these operating instructions may be changed without prior notice. OKM does not make any warranty for this document. This also applies without
More informationInstalling the IF-NMEASC & SC30 Windows XP Drivers & Software
Installing the IF-NMEASC & SC30 Windows XP Drivers & Software The following document will outline the installation and use of the IF-NMEASC and SC-30 USB drivers and SC-30Tool software in three parts:
More informationCongratulations on your purchase of a BPM Microsystems device programmer. Your new device programmer was designe d to provid e years of suppor t for
Congratulations on your purchase of a BPM Microsystems device programmer. Your new device programmer was designe d to provid e years of suppor t for thousand s of devices, with the use of optional socket
More informationData Recovery Cable Quick Start Guide
Data Recovery Cable Quick Start Guide DISCLAIMER: any repair or computer recovery should be done by a professional, trained computer technician. Do any of the below steps at your own risk. We are not responsible
More informationSUNNY BEAM USB Driver Installing the Sunny Beam USB Driver. 1 Sunny Beam USB Driver. Version: 1.4
SUNNY BEAM USB Driver Installing the Sunny Beam USB Driver Version: 1.4 1 Sunny Beam USB Driver The Sunny Beam USB driver is needed to connect a Sunny Beam to a computer. System requirements: The Sunny
More informationPIGCHAMP MOBILE. PigCHAMP Knowledge Software. Installation Guide for Mobile Units
PIGCHAMP MOBILE PigCHAMP Knowledge Software Installation Guide for Mobile Units Table of Contents: Important Note:... 4 Chapter 1: PC Setup... 5 A. Install PigCHAMP Mobile Manager on Windows XP...5 B.
More informationPrint Server Application Guide
Print Server Application Guide TD W8968 TD W8970 / TD W8970B TD W8980 / TD W8980B Rev: 1.0.0 1910010772 Contents Overview...1 Installation for Windows OS...2 Application for Windows OS...7 How to launch/exit
More informationUser Manual. Thermo Scientific Orion
User Manual Thermo Scientific Orion Orion Star Com Software Program 68X637901 Revision A April 2013 Contents Chapter 1... 4 Introduction... 4 Star Com Functions... 5 Chapter 2... 6 Software Installation
More informationRME Driver Install and Update Guide for Windows XP
RME Driver Install and Update Guide for Windows XP Copyright 2008 Synthax Inc. This step-by-step guide is intended to show RME users how to install drivers and set up a device for the first time under
More informationSoftware Manual LSeries Manager V1.2 Software Manual June 18, 2013. LSeries Manager 1.2. Software Manual
LSeries Manager 1.2 Software Manual Website: www.arri.com/service-lighting Page 1 of 14 Table of Contents 1 Download and Installation... 3 2 Start the LSeries Manager... 4 3 Lamphead Overview... 5 4 DMX
More information