Vicon Flash Upgrade Software
|
|
- Magdalene Baldwin
- 8 years ago
- Views:
Transcription
1 INSTRUCTION MANUAL Notes Refer to XX134 NO. XX REV Vicon Flash Upgrade Software It is possible to upgrade software for the SurveyorVFT and Surveyor -Mini Camera Domes through a PC using the Flash Upgrade software. Before the software can be upgraded, it is necessary to setup the hardware. The PC must be connected to the dome by means Vicon s V422-CONV RS-232/RS-422 interface converter/adapter and a cable assembly. See Figure 1. Note: The Flash Upgrade Software does not work with the IP models of the SurveyorVFT or Surveyor-Mini. Installing the Software The software must be installed on the computer prior to connecting the camera dome to a computer with the following minimum configuration: Pentium 233 MHz with 32 MB RAM 2 MB of free hard drive space CD-ROM drive 1 free serial port (COM 1, COM 2, COM 3 or COM 4) Mouse (for navigation) Windows '95, '98 (second edition), ME, NT, 2000 Professional or XP Home or Professional RS-232 to RS-422 protocol converter/adapter Software can be downloaded from Vicon s website from the Support tab, Technical Support, Software Downloads, SurveyorVFT: To install: 1. Power on and boot the computer to the Windows desktop. 2. Place the CD into the drive. 3. If it does not autorun, run the file on the CD named setup.exe. 4. Follow the software prompts to install the software onto the hard drive in the desired directory. There are two versions of the flash utility. Surveyor Flash Upgrade Version is the recommended version to use; however, it requires duplex communication (two pairs of wires between the dome and the PC). Also note that only one dome can be updated at a time. SVFT and Surveyor-Mini Utility 4.4 provides a simplex download tool, so more than one dome can be updated at a time. However, there is no response back that the transfer took place. The 4.4 Utility also provides a number of other tools, absolute position, source titling, and title conversion It is recommended that the user control the dome with the PC Direct Control Software first to ensure that the wiring and setup is correct and confirm the baud rate of the dome. This is essential, as the flash baud rate MUST be the same as the operational baud rate of the dome. For best results, run through the setup steps as quickly as possible. The camera dome will time out if too much time elapses between steps. Read all instructions first so that you re familiar with the program s operation. Copyright 2012 Vicon Industries Inc. All rights reserved. Product specifications subject to change without notice. Vicon and its logo, SurveyorVFT and Surveyor are registered trademarks of Vicon Industries Inc. Windows is a registered trademark of Microsoft Corp.; Pentium is a registered trademark of Intel Corp. Vicon part number Rev 1212 VICON INDUSTRIES INC., 89 ARKAY DRIVE, HAUPPAUGE, NEW YORK TEL: FAX: TOLL FREE: Hour Technical Support: VICON ( ) UK: +44 (0) WEB:
2 Figure 1 Connection Diagram (SurveyorVFT shown in example) Pin Out Connections RS-232/RS-422 Converter SurveyorVFT COMM TB3 Signal To Signal RXD- (RESPONSE IN -) PIN 4 (RESPONSE OUT -) RXD+ (RESPONSE IN +) PIN 3 (RESPONSE OUT +) GND (GROUND) PIN 5 (GROUND) T/R+ (COMMAND OUT +) PIN 1 (COMMAND IN +) T/R- (COMMAND OUT -) PIN 2 (COMMAND IN -) RS-232/RS-422 Converter Surveyor-Mini COMM TB3 Signal To Signal RXD- (RESPONSE IN -) PIN 3 (RESPONSE OUT -) RXD+ (RESPONSE IN +) PIN 4 (RESPONSE OUT +) GND (GROUND) PIN 5 (GROUND) T/R+ (COMMAND OUT +) PIN 1 (COMMAND IN +) T/R- (COMMAND OUT -) PIN 2 (COMMAND IN -) Communication Set Up 1. Have the RS-232 to RS-422 converter/adapter and cable ready. The converter/adapter is available from Vicon. Connect the camera dome to the cable/adapter and then to the PC Comm Port. Refer to Figure 1. Note: It is important that the adapter gets enough power. When using a laptop, be sure it is fully charged and turn off the power save features to assure the power remains high. When using a laptop with an adapter, it is recommended to use the external DC input if available. 2. Setup the Comm Port and Baud Rate. By default, the program is set to use the PC s Comm Port 1 and is set to communicate to the dome at 4800 baud. It is necessary to know the baud rate of the camera dome; the same rate MUST be selected for the utility. The PC Comm Port must be configured as follows: Bits: baud rate as high as possible Data Bits: 8 Parity: None Stop Bits: 1 Flow Control: None XX Flash Utility Download 2
3 When running Flash Utility 2.2.0, duplex mode is required. When running Flash Utility 4.0, no response is necessary, so simplex mode is adequate. The dome MUST be wired to the adapter in duplex mode to use the absolute position and source titling features, as these require getting data from and sending data to the dome. Flash Upgrade Utility Note for SurveyorVFT Camera Domes Only: The SurveyorVFT PCB has been updated to meet RoHS requirements. The new versions have blue PCBs; the previous PCBs were green. The new board has a new flash chip. Therefore, the flash code software is different from the old version. The units must be flashed accordingly. The flash code for the old version is 1.X.X, while the flash code for the new RoHS version is 2.X.X. The flash code version can be found by entering Preset 92; either App: 1.X.X or App: 2.X.X will display. All new versions of flash code are posted at Vicon s website: In the SVFT-PRS pressurized dome, the pressure sensor has been moved to the Customer Interface Board (CIB) on RoHS version; non-rohs versions had the pressure sensor as part of the housing. Flash Upgrade Utility Version The opening screen of Flash Utility software version (for duplex mode only) is displayed below. Use the Save button to store all custom settings, like presets, stored in the camera dome. Performing a Flash Upgrade resets all user settings to factory default. Use this option to store the custom settings, so that they can be returned to the camera dome after the Flash Upgrade is performed. After the Flash Utility is complete, press the Restore button to restore all the custom settings that were previously saved. 1. Click on the Flash button to begin the Flash Upgrade utility. 2. Use the Browse button to find the flash upgrade file or enter the path and file name directly into the textbox. The file must have the.hex extension. 3. Press the Begin button to send the command to the dome to begin the download session. 4. After the dome responds to the command to begin the session, the Next button will appear enabled. Click it to confirm the download. 5. The screen provides a selection of download baud rates. The option buttons range from 4800 to baud. Recommended selection is the option button. If for any reason the file transfer does not complete, check that the file being downloaded is the correct name and size. If it is correct, try again using a slower baud rate. Note: This is the baud rate just for the download; it is not the baud rate for the Flash Upgrade and the dome operation, which must be the same. 6. Press the Send button. There are two indicators for file transfer progress. One is the gauge that shows a graphic of progress. The other is a message that displays the state of the transfer at that moment. Watch for error messages. In case of error messages, check all cables and connections. When the message File Sent XX Flash Utility Download 3
4 appears, the download is completed successfully. Wait a few seconds for the camera dome to apply the update and reset; check the monitor for the version information. Flash Upgrade Utility Version 4.4 This utility works in both simplex and duplex mode connection. The Flash Utility application does not need a response (simplex mode) from the dome to proceed. To establish initial communication or to change PC Comm Port and Baud Rate settings, use the Settings menu. The Settings dropdown list also offers a Dome Type, SVFT (SurveyorVFT) or Surveyor Mini. Select the dome type that is being upgraded. Refer to the screen that follows. Note: After a dome type is selected, if a file for the other type is selected for download, an error message will display. However, dome mode can be changed without restarting the application. Dome Type selected display Select Dome Type Baud Rate Options Select download baud rate Be sure to select Application (never Boot) Select the file to download. Use the Browse feature to select the file for the SVFT or Surveyor-Mini. The screen provides a selection of download baud rates. The option buttons range from 4800 to baud. If for any reason the file transfer does not complete, check that the file being downloaded is the correct name and size. If it is correct, try again using a slower baud rate. Note: This is the baud rate just for the download; it is not the baud rate for the Flash Upgrade and the dome operation, which must be the same. For Code Type, Application must be selected; do not select Boot. For the SVFT Only: Select a delay time to allow the EEPROM memory to clear. This defines the amount of time to wait for the dome to delete old information before uploading the new information. This selection is grayed out in Surveyor-Mini mode. XX Flash Utility Download 4
5 Click Send File. The following screens display. SVFT and Surveyor-Mini Utility Download Screen Camera Dome Video Screen The status of simplex Flash Download can only be observed on the camera dome video screen, due to the nature of simplex mode. It is possible to observe a successful transfer in the application screen upload progress bar while in reality the transfer failed. The only way to know the transfer is complete is to view the message Programming Complete on the video screen. Absolute Position This feature is used to command the dome to a particular position determined by pan, tilt, zoom and iris. It can also be used to retrieve absolute positioning coordinates. These values are read with respect to the camera dome s zero compass feature. The Absolute Positioning program requires duplex mode. Refer to SurveyorVFT Programming Manual XX134-4X or the Surveyor-Mini Programming Manual XX203-4X. Click on Utility and select Absolute Position. The screen below displays. It is recommended to get the current position status first, to be used as reference point, by clicking the Get Status button. If the status feedback is all 0s, communication between PC and camera dome is broken; check the set up. Enter in the desired Pan (0-2880), Tilt (0-760), Zoom (0-2047) and Iris (0-255) levels. The pan range is 0 to 360 degrees. The tilt range is 0 to 95 degrees. For iris level, use dome s preset 94 menu reference. XX Flash Utility Download 5
6 XX Flash Utility Download 6
7 Source Titling This enables the user to edit text titles for cameras, alarms, sectors, and presets located in the configuration file of the dome. The Source Title configuration requires duplex mode. Click on Utility and select Source Titling. The screen below displays. Select Open Dropdown List to select Camera, Alarm, Sector or Preset to be given title File name (.bin) 1. Click on Utility menu, select Configuration Upload From Unit (from camera dome to PC), name the file and save (.bin file). If there already is a SurveyorVFT or Surveyor-Mini configuration file, this step can be omitted. 2. Open the.bin file from the File menu. 3. Edit titles by selecting the Source Titling field values; click Save Changes for each altered title. Some of the characters are not supported by the dome, for #, %; they are translated to a space character. 4. When complete, click on Utility menu and select Configuration Download To Unit (from PC to SVFT/Surveyor-Mini). Click Open and the file is sent to the dome. Refer to the Figure that follows. XX Flash Utility Download 7
8 Title Conversion - SurveyorVFT Camera Dome Only This feature is used to extract Title (camera, alarm, sector and preset) information from one SurveyorVFT dome and transfer it to another SurveyorVFT dome. 1. Click on Utility and select Title Conversion. The screen below displays. It is required to set both domes to address 1 using Vicon protocol. 2. Select the Conversion Mode; Green and Blue refer to the color of the main board. You can mix a Green CIB (Customer Interface Board) with a Blue main. Example For an existing dome with a Green main (v1.x) and want to transfer the titles to a new dome with a Blue main (v2.x), select "Green Main (1.x) to Blue (2.x)" XX Flash Utility Download 8
9 Upload Source - Upload from SurveyorVFT dome or use Browse to find a stored profile on the PC. Note - The Source Titling feature can be used to modify titles on an existing profile. Upload Target - Replace the Source dome with the new Target dome. (The CIB can be left in place if it cannot be easily replaced.) Use the Upload Target feature or Browse. Note - Uploading from a Target causes the dome to install defaults before uploading the blank profile. This is done to ensure that there is a clean empty profile to use for Importing titles from the Source file. Import Titles - Now that the Utility has both the Source and blank Target files, click Import Titles to copy title information from the Source file to the Target file. Download Converted File- This button will be highlighted after the Import Titles has successfully completed. Leave the Target dome connected and press Download Converted Tile to complete the Title Conversion. Troubleshooting: 1) Adapter - It is very important that the RS-232 to RS-422 adapter be wired correctly. The RS-232 side MUST be connected to the PC and the RS-422 side goes to the SurveyorVFT or Surveyor-Mini. 2) File Always make sure the file is the correct name, size and date. Contact Technical Support if you have any questions. XX Flash Utility Download 9
10 Vicon Industries Inc. Corporate Headquarters 89 Arkay Drive Hauppauge, New York Fax: Vicon Europe Headquarters Brunel Way Fareham, PO15 5TX United Kingdom +44 (0) Fax: +44 (0) Vicon Germany Kornstieg 3 D Neumuenster Phone: +49 (0) Fax: +49 (0) Vicon China Unit 5, 17/F, Metropole Square 2 On Yiu Street, Shatin New Territories, Hong Kong (852) Fax: (852) Internet Address:
Vicon Flash Upgrade Software
NOTES NO. REV. SEC. INSTRUCTION MANUAL Refer to XX134-11-00 1108 3 XX134 Vicon Flash Upgrade Software It is possible to upgrade software for the SurveyorVFT through a PC using the Flash Upgrade software.
More informationINSTRUCTION MANUAL. Installing the Software NO. XX134-24-00. NOTES Refer to XX134 REV. 510 SEC. 3
INSTRUCTION MANUAL NOTES Refer to XX134 NO. XX134-24-00 REV. 510 Vicon Direct Control Software It is possible to control the SurveyorVFT or Surveyor -Mini camera dome from a PC using the Direct Control
More informationFile Management Utility. T u t o r i a l
File Management Utility T u t o r i a l Contents System Requirements... 2 Preparing Files for Transfer to GlobalMark... 2 Application Launch... 2 Printer Setup... 2 Communication Status... 4 Communication
More informationHYBRID NETWORK VIDEO RECODERS WITH INTERNAL RAID RECOVERY PROCEDURE
XX112-91-00 HYBRID NETWORK VIDEO RECODERS WITH INTERNAL RAID RECOVERY PROCEDURE Copyright 2006 Vicon Industries Inc. All rights reserved. Product specifications subject to change without notice. Vicon
More informationModel 288B Charge Plate Graphing Software Operators Guide
Monroe Electronics, Inc. Model 288B Charge Plate Graphing Software Operators Guide P/N 0340175 288BGraph (80207) Software V2.01 100 Housel Ave PO Box 535 Lyndonville NY 14098 1-800-821-6001 585-765-2254
More informationConfig software for D2 systems USER S MANUAL
DT-CONFIG SOFTWARE Config software for D2 systems USER S MANUAL CONTENTS 1. Introductions ------------------------------------------------------------------- 3 2. System Requirement and Connection ----------------------------------------
More informationWinPFT File Transfer Utility (Catalog No. 2711-ND7)
Technical Data WinPFT File Transfer Utility (Catalog No. 2711-ND7) Overview WINPFT is a stand-alone Windows utility which lets you transfer applications developed for standard PanelView terminals or Dataliner
More informationSEC 4100 SYSTEM MONITOR Programmable Serial Interface Card Series 2
SEC 4100 SYSTEM MONITOR Programmable Serial Interface Card Series 2 USER MANUAL Rev. P1.11 September 13, 2006 DeltaV is a trademark of Emerson Process Management, Inc Emerson Process Management, Inc. 1998,
More information3.1 RS-232/422/485 Pinout:PORT1-4(RJ-45) RJ-45 RS-232 RS-422 RS-485 PIN1 TXD PIN2 RXD PIN3 GND PIN4 PIN5 T+ 485+ PIN6 T- 485- PIN7 R+ PIN8 R-
MODEL ATC-2004 TCP/IP TO RS-232/422/485 CONVERTER User s Manual 1.1 Introduction The ATC-2004 is a 4 Port RS232/RS485 to TCP/IP converter integrated with a robust system and network management features
More informationPORTABLE DATA COLLECTION TERMINAL
PORTABLE DATA COLLECTION TERMINAL WINDOWS TRANSFER UTILITY HELP FILES BETA EDITION Compsee, Inc. A Subsidiary of McRae Industries, Inc. 2 Welcome Thank you for using the Apex III Windows Transfer Utility
More informationEngineering Change Order (ECO): 8012 Effective Date: November 14, 2002 Purpose
ETC Release Note Network Configuration Editor (NCE) Product Line: Description: Network Configuration Editor (NCE) Version 3.0.2 Software Engineering Change Order (ECO): 8012 Effective Date: November 14,
More informationUser s Manual TCP/IP TO RS-232/422/485 CONVERTER. 1.1 Introduction. 1.2 Main features. Dynamic DNS
MODEL ATC-2000 TCP/IP TO RS-232/422/485 CONVERTER User s Manual 1.1 Introduction The ATC-2000 is a RS232/RS485 to TCP/IP converter integrated with a robust system and network management features designed
More informationCashFlow Programming Module CPM
CashFlow Programming Module CPM Installation & User Guide GB REV G4 08/08/2006 Table of Content Table of Content... 2 CashFlow Programming Module (CPM)... 4 What is a CPM?... 4 CPM Identification... 4
More informationLOVELINK III- Process Monitoring, Logging, Graphing, & Configuration
LOVELINK III- Process Monitoring, Logging, Graphing, & Configuration VERSION 1.00.00 USER MANUAL Updated 09/13/2002 Table of Contents Hardware/Software Requirements...2 Computer Requirements...2 Instrument
More informationHypercom Key Loading and Management (HKLM) RS232 PPP Key Injection PC Setup Guide
Hypercom Key Loading and Management (HKLM) RS232 PPP Key Injection PC Setup Guide Hypercom Corporation 8888 East Raintree Drive Scottsdale, Arizona 85260 USA Corporate Telephone: 480.642.5000 Corporate
More informationImportant. Please read this User s Manual carefully to familiarize yourself with safe and effective usage.
Important Please read this User s Manual carefully to familiarize yourself with safe and effective usage. About ScreenManager Pro for LCD... 3 1. Setting Up... 4 1-1. System Requirements...4 1-2. Installing
More informationLiebert IntelliSlot Web Cards
Monitoring For Business-Critical Continuity Liebert IntelliSlot Web Cards Firmware Upgrade Manual Liebert IntelliSlot Web Card, Liebert IntelliSlot Web Card-LB, Liebert IntelliSlot Web Card-LBDS, Liebert
More informationIP SERIAL DEVICE SERVER
IP SERIAL DEVICE SERVER ( 1 / 2 / 4 serial port ) Installation guide And User manual Version 1.0 1Introduction... 5 1.1Direct IP mode...5 1.2Virtual COM mode...5 1.3Paired mode...6 1.4Heart beat... 6
More informationDataLINE Data Retrieval
Container Refrigeration INSTALLATION GUIDE for DataLINE Data Retrieval 62 10628 Rev B INSTALLATION GUIDE CONTAINER REFRIGERATION UNIT DataLINE Data Retrieval CONTENTS Paragraph Number Page 1. Introduction...
More informationSoftware User Guide UG-461
Software User Guide UG-461 One Technology Way P.O. Box 9106 Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 Fax: 781.461.3113 www.analog.com ezlinx icoupler Isolated Interface Development Environment
More informationSOFTWARE INSTALLATION INSTRUCTIONS
AUDITGARD LGA Electronic Combination Lock SOFTWARE INSTALLATION INSTRUCTIONS Implementation Package The AuditGard Software implementation package includes: 707013 AuditGard Software Install CD 42145 Programming/Audit
More informationSUDT AccessPort TM Advanced Terminal / Monitor / Debugger Version 1.37 User Manual
SUDT AccessPort TM Advanced Terminal / Monitor / Debugger Version 1.37 User Manual Version 1.0 - January 20, 2015 CHANGE HISTORY Version Date Description of Changes 1.0 January 20, 2015 Initial Publication
More informationManual Client Management Software HDR50-CMS
Manual Client Management Software HDR50-CMS HDR50-CMS (Client Management Software) A-1. Install HDR50-CMS for Windows PC HDR50-CMS is a program for communication between DVR and PC to control signal and
More informationIPRS-7 IP/GPRS PC Receiver Software Quick Start V1.2
IPRS-7 IP/GPRS PC Receiver Software Quick Start V1.2 Overview Introduction Before You Begin Installation The IPRS-7 Main Page Configuring the IPRS-7 (IPRS-7 splash screen pictured) Introduction The IPRS-7
More informationOWNERS MANUAL. Status Monitor. for Windows 95, 98, ME, NT 4, 2000 & XP. SIGNALCRAFTERS TECH, INC. www.signalcrafters.com
OWNERS MANUAL Status Monitor for Windows 95, 98, ME, NT 4, 2000 & XP SIGNALCRAFTERS TECH, INC. www.signalcrafters.com 57 Eagle Rock Avenue, East Hanover, NJ 07936 Tel: 973-781-0880 or 800-523-5815 Fax:
More informationUser Manual. Thermo Scientific Orion
User Manual Thermo Scientific Orion Orion Star Com Software Program 68X637901 Revision A April 2013 Contents Chapter 1... 4 Introduction... 4 Star Com Functions... 5 Chapter 2... 6 Software Installation
More informationGuide to Installing BBL Crystal MIND on Windows 7
Guide to Installing BBL Crystal MIND on Windows 7 Introduction The BBL Crystal MIND software can not be directly installed on the Microsoft Windows 7 platform, however it can be installed and run via XP
More informationTDP-136 TRANSCEIVER DATA PROGRAMMER
TDP-136 TRANSCEIVER DATA PROGRAMMER PC SOFTWARE INSTALLATION & OPERATING INSTRUCTIONS Til Document No. 00RE277 Rev. A (Software V1.1x) NOV 2000 Technisonic Industries Limited 250 Watline Avenue, Mississauga,
More informationOPERATION MANUAL. MV-410RGB Layout Editor. Version 2.1- higher
OPERATION MANUAL MV-410RGB Layout Editor Version 2.1- higher Table of Contents 1. Setup... 1 1-1. Overview... 1 1-2. System Requirements... 1 1-3. Operation Flow... 1 1-4. Installing MV-410RGB Layout
More informationHoneywell Internet Connection Module
Honeywell Internet Connection Module Setup Guide Version 1.0 - Page 1 of 18 - ICM Setup Guide Technical Support Setup - Guide Table of Contents Introduction... 3 Network Setup and Configuration... 4 Setting
More informationDUKANE Intelligent Assembly Solutions
PC Configuration Requirements: Configuration Requirements for ipc Operation The hardware and operating system of the PC must comply with a list of minimum requirements for proper operation with the ipc
More informationWeb Server XX220-11-00. Configuration Guide
Configuration Guide XX220-11-00 Web Server Vicon Industries Inc. Tel: 631-952-2288 Fax: 631-951-2288 Toll Free: 800-645-9116 24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300
More informationHistory of Revisions. Ordering Information
No part of this document may be reproduced in any form or by any means without the express written consent of II Morrow Inc. II Morrow, Apollo, and Precedus are trademarks of II Morrow Inc. Windows is
More informationCOMBOGARDPRO. 39E Electronic Combination Lock SOFTWARE INSTALLATION INSTRUCTIONS
COMBOGARDPRO 39E Electronic Combination Lock SOFTWARE INSTALLATION INSTRUCTIONS IMPLEMENTATION PACKAGE The ComboGard Pro Software implementation package includes: 707012 ComboGard Pro Software Install
More informationAXIS Camera Station Quick Installation Guide
AXIS Camera Station Quick Installation Guide Copyright Axis Communications AB April 2005 Rev. 3.5 Part Number 23997 1 Table of Contents Regulatory Information.................................. 3 AXIS Camera
More informationSharpdeskTM R3.1. Installation Guide Version 3.1.01
SharpdeskTM R3.1 Installation Guide Version 3.1.01 1 Copyright 2000-2004 by Sharp Corporation. All rights reserved. Reproduction, adaptation or translation without prior written permission is prohibited,
More informationGV-Data Capture V3 Series User's Manual
GV-Data Capture V3 Series User's Manual Before attempting to connect or operate this product, please read these instructions carefully and save this manual for future use. 2006 GeoVision, Inc. All rights
More informationSecureLinx Spider Duo Quick Start Guide
SecureLinx Spider Duo Quick Start Guide SecureLinx Spider Duo Quick Start Guide SecureLinx Spider Duo QUICK START GUIDE CONTENTS Overview... 2 What s In The Box... 3 Installation and Network Settings...
More informationSMS (Server Management Software) Digital Video Recorder. User s Manual
SMS (Server Management Software) Digital Video Recorder User s Manual Contents 1 - Introduction 2 1.1 About this manual 2 1.2 Configuration 2 1.3 SMS Functions 2 1.4 Product Information 2 1.5 System Requirements
More informationNVMS - 1000 USER MANUAL. Version 2.1.0
NVMS - 1000 USER MANUAL Version 2.1.0 Contents 1 Software Introduction... 1 1.1 Summary... 1 1.2 Operation Environment... 1 1.3 Install and Uninstall... 2 1.3.1 Install the Software... 2 1.3.2 Uninstall
More informationUSER GUIDE. Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6
KRAMER ELECTRONICS LTD. USER GUIDE Ethernet Configuration Guide (Lantronix) P/N: 2900-300321 Rev 6 Contents 1 Connecting to the Kramer Device via the Ethernet Port 1 1.1 Connecting the Ethernet Port Directly
More informationNortel Networks Call Center Reporting Set Up and Operation Guide
Nortel Networks Call Center Reporting Set Up and Operation Guide www.nortelnetworks.com 2001 Nortel Networks P0919439 Issue 07 (24) Table of contents How to use this guide... 5 Introduction...5 How this
More informationKorosi Monitoring System (KMS) Software Manual
PT. KOROSI SPECINDO Corrosion Monitoring System Eng. Doc. No.: KS-MNL-KMS Korosi Monitoring System (KMS) Software Manual Revision Date Prepared Approved Description 0 23/05/2008 ES JH Issued for approval
More informationUSER MANUAL GUIMGR Graphical User Interface Manager for FRM301/FRM401 Media Racks
USER MANUAL GUIMGR Graphical User Interface Manager for FRM301/FRM401 Media Racks CTC Union Technologies Co., Ltd. Far Eastern Vienna Technology Center (Neihu Technology Park) 8F, No. 60 Zhouzi St. Neihu,
More information32 Transferring Projects and Data
32 Transferring Projects and Data This Chapter explains how to transfer GP-Pro EX project files to the GP and how to transfer the project files stored on the GP to your PC. Please start by reading 32.1
More informationLAN / WAN Connection Of Instruments with Serial Interface By Using a Terminal Server
Products: EFA with EFA Scan, DVRM and DVMD with Realtime Monitor or Stream Explorer DVMD-B1 LAN / WAN Connection Of Instruments with Serial Interface By Using a Terminal Server Remote control of test and
More informationUltra Thin Client TC-401 TC-402. Users s Guide
Ultra Thin Client TC-401 TC-402 Users s Guide CONTENT 1. OVERVIEW... 3 1.1 HARDWARE SPECIFICATION... 3 1.2 SOFTWARE OVERVIEW... 4 1.3 HARDWARE OVERVIEW...5 1.4 NETWORK CONNECTION... 7 2. INSTALLING THE
More informationPOWER NETWORK. 800-02577-iPcams 2/10 Rev. A
POWER NETWORK Total Connect Online Help Guide for: ip Cameras ipcam-wi Camera ipcam-pt Pan and Tilt Camera 800-02577-iPcams 2/10 Rev. A POWER NETWORK ip Cameras Online Help Guide This guide covers the
More informationFileMover 1.2. Copyright Notice. Trademarks. Patents
FileMover 1.2 Copyright Notice No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any human or computer language, in any form or by
More informationNetwork Scanner Tool R3.1. User s Guide Version 3.0.04
Network Scanner Tool R3.1 User s Guide Version 3.0.04 Copyright 2000-2004 by Sharp Corporation. All rights reserved. Reproduction, adaptation or translation without prior written permission is prohibited,
More informationAppendix A. CMS(Client Management Software)
Appendix A. CMS(Client Management Software) A-1. Install CMS for Windows PC CMS is a program for communication between DVR and PC to control signal and video. Insert the enclosed CD, and go to CD-ROM Drive
More informationUser Guide for Windows 10
User Guide for Windows 10 System requirements E10684 First Edition July 2015 To facilitate a smoother transition from your previous operating system, read the system requirements below before upgrading
More informationPTPhoneManager II. User guide
COMMUNICATION AT ITS BEST PTPhoneManager II User guide Communications A member of PEIKER group DOCUMENT PEI TEL Communications GmbH - PTPhoneManager II - 2 - T ABLE OF CONTENTS Table of contents Table
More informationMonitoring Network DMN
Monitoring Network DMN User Manual Table of contents Table of contents... 2 1. Product features and capabilities... 3 2. System requirements... 5 3. Getting started with the software... 5 3-1 Installation...
More informationWA Manager Alarming System Management Software Windows 98, NT, XP, 2000 User Guide
WA Manager Alarming System Management Software Windows 98, NT, XP, 2000 User Guide Version 2.1, 4/2010 Disclaimer While every effort has been made to ensure that the information in this guide is accurate
More informationMaster-Touch and ValuMass. Modbus Communications. INSTRUCTION MANUAL 80202201 (Rev. 2.1)
Master-Touch and ValuMass Modbus Communications INSTRUCTION MANUAL 80202201 (Rev. 2.1) Eldridge Products, Inc. 2700 Garden Road, Building A Monterey, CA 93940 Tel: 800/321-3569 or 831/648-7777 Fax: 831/648-7780
More informationRSM Web Gateway RSM Web Client INSTALLATION AND ADMINISTRATION GUIDE
RSM Web Gateway RSM Web Client INSTALLATION AND ADMINISTRATION GUIDE Installation and Administration Guide RSM Web Client and RSM Web Gateway 17 August, 2004 Page 1 Copyright Notice 2004 Sony Corporation.
More informationPDA Software Manual For the Windows CE and Mobile Operating Systems
PDA Software Manual For the Windows CE and Mobile Operating Systems Global Water Instrumentation, Inc. 151 Graham Road P.O. Box 9010 College Station, TX 77842-9010 T: 800-876-1172 Int l: (979) 690-5560,
More informationHow To Set Up Flir Cloud Client For Pc Or Mac Or Mac (For Pc Or Ipad) On A Pc Or Pc Or Mouse (For Mac) On An Iphone Or Ipa) On Pc Or Tv (For Ipa
Instruction Manual FLIR Cloud Services Client Instruction Manual FLIR Cloud Services Client #LX400018; r. 2.0/14567/14568; en-us iii Table of contents 1 Setting up FLIR Cloud Client for PC or Mac...1
More informationGlobal Water Instrumentation, Inc.
Global Water Instrumentation, Inc. 151 Graham Road P.O. Box 9010 College Station, TX 77842-9010 Telephone : 800-876-1172 International : (979) 690-5560, Fax : (979) 690-0440 e-mail : globalw@globalw.com
More informationNewton Backup Utility User s Guide. for the Windows Operating System
Newton Backup Utility User s Guide for the Windows Operating System K Apple Computer, Inc. 1995 Apple Computer, Inc. All rights reserved. Under the copyright laws, this manual may not be copied, in whole
More informationKeep it Simple Timing
Keep it Simple Timing Support... 1 Introduction... 2 Turn On and Go... 3 Start Clock for Orienteering... 3 Pre Start Clock for Orienteering... 3 Real Time / Finish Clock... 3 Timer Clock... 4 Configuring
More informationExeba -ATS. User Guide. Escan Technologies Corporation
Escan Technologies Corporation Exeba -ATS User Guide Escan Technologies Corp. 12140 Severn Way Riverside, CA 92503 Phone (909) 270-0043 Fax (909) 270-0920 1 ESCAN TECHNOLOGIES CORPORATION Exeba -ATS User
More informationUser Manual V1.0. Remote Software
User Manual V1.0 Notice: The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change
More informationCenturion PLUS CPC4 Download Guide
Centurion PLUS CPC4 Download Guide using C4 File Transfer Utility. 1010537 03 01 10 Section 50 1.0 Background: 1.1 The Centurion PLUS Control system consists of a Centurion PLUS Core (CPC4 1) and Color
More informationIndustrial L2+ Managed Gigabit/ 10 Gigabit Ethernet Switch. IGS-5225 Series. Quick Installation Guide
Industrial L2+ Managed Gigabit/ 10 Gigabit Ethernet Switch IGS-5225 Series Quick Installation Guide Table of Contents 1. Package Contents... 3 2. Requirements... 4 3. Wiring DC Power Inputs... 5 4. Terminal
More informationLOREX CLIENT Remote Software 4.0
LOREX CLIENT Remote Software 4.0 Instruction Manual English Version 2.0 MODEL: L20WD800 Series www.lorexcctv.com Copyright 2008 LOREX Technology Inc. Table of Contents Table of Contents Software Installation...
More informationSoftware Installation and Quick Start Guide. EnergyMax -USB/RS Sensor System
Software Installation and Quick Start Guide EnergyMax -USB/RS Sensor System Software Installation and Quick Start Guide EnergyMax-USB/RS Sensor System 27650 SW 95th Ave. Wilsonville, OR 97070 This document
More informationQuick Note 32. Using Digi RealPort with a Digi TransPort Router. UK Support September 2012
Quick Note 32 Using Digi RealPort with a Digi TransPort Router UK Support September 2012 1 Contents 1 Introduction... 3 1.1 Outline... 3 1.2 Assumptions... 3 1.3 Version... 3 2 Configuration & scenario...
More informationTDP43ME NetPS. Network Printer Server. Control Center. for Ethernet Module
Panduit Corp. 2010 TDP43ME NetPS PA26306A01 Rev. 01 11-2010 Network Printer Server Control Center for Ethernet Module NOTE: In the interest of higher quality and value, Panduit products are continually
More informationTR-3 Channel Editor. Software Manual
TR-3 Channel Editor Software Manual Trilithic Company Profile Trilithic is a privately held manufacturer founded in 1986 as an engineering and assembly company that built and designed customer-directed
More informationHandheld LPC Utility Software for Windows. Operation Manual
Handheld LPC Utility Software for Windows MODEL S388-70 Operation Manual Read this manual carefully and understand the warnings described in this manual before operating the product. Keep this manual handy
More informationUpgrading from Call Center Reporting to Reporting for Contact Center. BCM Contact Center
Upgrading from Call Center Reporting to Reporting for Contact Center BCM Contact Center Document Number: NN40010-400 Document Status: Standard Document Version: 02.00 Date: June 2006 Copyright Nortel Networks
More informationProgramming and Using the Courier V.Everything Modem for Remote Operation of DDF6000
Programming and Using the Courier V.Everything Modem for Remote Operation of DDF6000 1.0 Introduction A Technical Application Note from Doppler System July 5, 1999 Version 3.x of the DDF6000, running version
More informationTitle Page. Installation Guide. PowerChute plus Version 5.0.1. for Windows 95
Title Page PowerChute plus Version 5.0.1 for Windows 95 Notice Page : PowerChute plus for Windows 95 version 5.0.1 PowerChute plus License Statement This software is protected by both United States copyright
More informationSA-9600 Surface Area Software Manual
SA-9600 Surface Area Software Manual Version 4.0 Introduction The operation and data Presentation of the SA-9600 Surface Area analyzer is performed using a Microsoft Windows based software package. The
More informationDevice configurator DRC200
Operating manual 42/49-27 EN Engineer IT Device configurator DRC200 R&C Process Data Management Software Impressum Device configurator DRC200 Operating manual Document No. 42/49-27 EN Date of issue: 11.02
More informationHow To Use Mview On A Powerline 2.2 (Powerline) On A Pc Or Macbook 2 (Powerplst) On An Iphone Or Ipa 2 (Aldo) On Your Iphon 2 (
mview for V8.53 and Later Motion Software mview is an elevator monitoring application. Through 1 Ethernet, the computer running mview may be connected directly to a single Motion 2000 or Motion 4000 controller
More informationMonitor Program (Windows version) Instruction Manual
Monitor Program (Windows version) Instruction Manual Department of Anaesthesia and Intensive Care The Chinese University of Hong Kong Version 4.0BAugust 2004 CONTENTS Chapter Page 1 Introduction 3 Basic
More informationViconNet/Software House C Cure Integration
User Guide XX250-00-01 ViconNet/Software House C Cure Integration Vicon Industries Inc. Tel: 631-952-2288 Fax: 631-951-2288 Toll Free: 800-645-9116 24-Hour Technical Support: 800-34-VICON (800-348-4266)
More informationS&G Audit Lock. Audit Trail Software Manual
S&G Audit Lock Audit Trail Software Manual The Sargent & Greenleaf Audit Lock is designed to provide a high level of security. One of the ways they accomplish this is by offering detailed audit trails.
More information1. Central Monitoring System Software
1. Central Monitoring System Software 1-1. General information CMS program is an application with which users not only watch and control remote DVRs, but also receive video/audio data or alarm signals
More informationGetting Started with Vision 6
Getting Started with Vision 6 Version 6.9 Notice Copyright 1981-2009 Netop Business Solutions A/S. All Rights Reserved. Portions used under license from third parties. Please send any comments to: Netop
More informationTable of Contents. 1. Overview... 3. 1.1 Materials Required. 3 1.2 System Requirements. 3 1.3 User Mode 3. 2. Installation Instructions..
Table of Contents 1. Overview..... 3 1.1 Materials Required. 3 1.2 System Requirements. 3 1.3 User Mode 3 2. Installation Instructions.. 4 2.1 Installing the On Call Diabetes Management Software. 4 2.2
More informationDevice Installer User Guide
Device Installer User Guide Part Number 900-325 Revision B 12/08 Table Of Contents 1. Overview... 1 2. Devices... 2 Choose the Network Adapter for Communication... 2 Search for All Devices on the Network...
More informationOSM 2007 MONITORING SOFTWARE
OSM 2007 MONITORING SOFTWARE Contents Preparation...3 Software Installation...4 Configuring OSM...6 Connecting a Device...16 Connecting to Station Monitoring Software...19 Troubleshooting...23 Installing
More informationVERITAS Backup Exec TM 10.0 for Windows Servers
VERITAS Backup Exec TM 10.0 for Windows Servers Quick Installation Guide N134418 July 2004 Disclaimer The information contained in this publication is subject to change without notice. VERITAS Software
More informationDIRECT INTERNET DATA. User s Guide
DIRECT INTERNET DATA User s Guide Iridium Satellite LLC Rev. 2; June 15, 2001 DIRECT INTERNET DATA ------------------------------------------------------------------------------------- TABLE OF CONTENTS
More informationNetwork Management Card Wizard--1. Introduction... 1 Using the Network Management Card Wizard... 5
Contents Network Management Card Wizard--1 Introduction....................................... 1 Using the Network Management Card Wizard................ 5 File Transfers--10 Introduction......................................
More informationIn-System Programmer USER MANUAL RN-ISP-UM RN-WIFLYCR-UM-.01. www.rovingnetworks.com 1
RN-WIFLYCR-UM-.01 RN-ISP-UM In-System Programmer 2012 Roving Networks. All rights reserved. Version 1.1 1/19/2012 USER MANUAL www.rovingnetworks.com 1 OVERVIEW You use Roving Networks In-System-Programmer
More informationPC Program User s Guide (01.01.05) 1. Connecting the PC. 2. Installation and Start-up. 3. Programming
Work Off-Line Set up a new database or modify a previously saved database (without being connected to the telephone system). This helps minimize on-site programming time. Work On-Line (connected directly
More informationAvigilon Control Center Server User Guide
Avigilon Control Center Server User Guide Version 4.10 PDF-SERVER-D-Rev1 Copyright 2011 Avigilon. All rights reserved. The information presented is subject to change without notice. No copying, distribution,
More informationPARTNER ACS R4.0 Remote Administration R4.0. Getting Started
PARTNER ACS R.0 Remote Administration R.0 Getting Started 8-6-66 700080 Issue May 00 Copyright 00, Avaya Inc. Document 8-6-66 All Rights Reserved 700080 Printed in USA Issue May 00 Notice Every effort
More informationUser s Guide for version 5 Page
Network Management Interface Catalog VPi 32.15E For use with these ATS products: 7000 & 4000 Series (Group 5 Controller) Series 300 (Group 1 Controller), and 940, 962, 436, 434, 447, 448 (Group 6A/7A Control
More informationSQL Server 2008 R2 Express Installation for Windows 7 Professional, Vista Business Edition and XP Professional.
SQL Server 2008 R2 Express Installation for Windows 7 Professional, Vista Business Edition and XP Professional. 33-40006-001 REV: B PCSC 3541 Challenger Street Torrance, CA 90503 Phone: (310) 303-3600
More informationProgramming Flash Microcontrollers through the Controller Area Network (CAN) Interface
Programming Flash Microcontrollers through the Controller Area Network (CAN) Interface Application te Programming Flash Microcontrollers through the Controller Area Network (CAN) Interface Abstract This
More informationAdditional Requirements for ARES-G2 / RSA-G2. One Ethernet 10 Base T/100 Base TX network card required for communication with the instrument.
TA Instruments TRIOS Software Installation Instructions Installation Requirements Your TRIOS Instrument Control software includes all the components necessary to install or update the TRIOS software, as
More informationManual. Danfoss Central Station Communications Software Version 3
Manual Danfoss Central Station Communications Software Version 3 RS.8A.Q1.02 1-2001 Contents Introduction 4 System Overview 4 Minimum and Recommended Hardware Requirements 4 Using the Keyboard to Select
More informationUser Manual for Operation Staff Page 1 of 37. Table of Content
User Manual for Operation Staff Page 1 of 37 Table of Content 1 Introduction...2 1.1 Objectives and Limitation...2 1.2 Hardware...3 1.3 Software...3 1.4 Synchronization...5 1.5 Interface...9 1.6 Solution
More informationSending SMS Messages and E-mails
GDW-11 GSM Modem Sending SMS Messages and E-mails AN-0139-ENG rev 3.1 Page 1 Contents 1. Introduction - Sending SMS Messages... 2. Configuring the GDW-11... 3. Configuring Hyperterminal. 4. Method 1- Using
More information