2200 Series. 2D Imager Barcode. Scanner User Guide V1.0

Transcription

1 2200 Series 2D Imager Barcode Scanner User Guide V1.0

2 Table of Contents Chapter 1 Factory Settings Factory Settings... 3 Chapter 2 Communication Interface RS-232 Serial Port Communication Baud Rate Settings Parity Bit Settings USB Interface Communication Serial Port Command Format... 7 Chapter 3 Common Function Settings Scanning Mode Settings Beeper-Good Read Switching Settings LED-Good Read Switching Settings Barcode Scanning Delay Trigger Timeout Settings Chapter 4 Data Format Configuration General Settings Add Prefix Add Suffix Scanner Serial Number Display Software Version Display Chapter5 Barcode Type D Barcode Interleaved 2 of 5( by Default) China Post(Hong Kong)( by Default) Matrix 2 of 5( by Default) Codabar( by Default) MSI(Plessey)( by Default)

3 1.6 Code 128( by Default) Code 39( by Default) Code 93( by Default) Standard(IATA,Airline) 2 of 5(two-bar start/stop)( by Default) Industrial 2 of 5 (three-bar start/stop)( by Default) GS1 DataBar (RSS)( by Default) Telepen( by Default) Trioptic Code( by Default) UPC-A/EAN13( by Default) Code 11( by Default) D Barcode QR( by Default) Data Matrix( by Default) PDF417( by Default) Aztec( by Default) Hanxin( by Default)

4 Chapter 1 Factory Settings 1. Factory Settings Scanning the following barcode can restore the scanner to the factory defaults. Restore All Factory Defaults 3

5 Chapter 2 Communication Interfaces 2200 provides a TTL-232 interface and a USB interface to communicate with the host device. The host device can receive scanned data and send commands to control the engine or to access/alter the configuration information of the engine via the TTL-232 or USB interface. 1. RS-232 Serial Communication Serial communication interface is usually used when connecting the scanner to a host device (like PC, POS). However, to ensure smooth communication and accuracy of data, you need to set communication parameters (including baud rate, parity check, data bit and stop bit) to match the host device. Default serial communication parameters are listed below. Make sure all parameters match the host requirements. Parameter Serial Communication Default Setting Standard RS-232 Baud Rate Parity Check None Data Bits 8 Stop Bits 1 Hardware Flow Control None 1.1 Baud Rate

6 5

7 Parity Check None,7,1 None,7,2 None,8,1 Even,7,1 Even,7,2 Even,8,1 6

8 Odd,7,1 Odd,7,2 Odd,8,1 2. USB Interface Communication To connect USB cable, scanners can communicate through USB HID-KB and USB Virtual Serial Port. USB HID-KB Configuration Code USB Virtual Serial Port Configuration Code 7

9 3. Serial port command Format User Command Format: \x02\x11\x03xxxxxx. Serial Command Trigger Trigger push command: Trigger release command: \x02p\x03 \x02r\x03 8

10 Chapter 3 General Function Setting 1. Scanning Mode Settings Manual Mode:Through Key Trigger to scan code 2. Beeper-Good Read Switching Setting Good Read Beeper Good Read Beeper 9

11 3. LED-Good Read Switching Setting Good Read LED Good Read LED 4. Barcode Scanning Delay After successfully scanning a barcode will delay to appointed time to decode next code, the default is 0ms Delay 0ms Delay 250ms Delay 750ms Delay 1250ms 10

12 5. Trigger Timeout Setting Button Trigger Timeout Setting,Default Timeout 30s 30s(Default) 10s 2s 11

13 Chapter 4 Data Format Setting 1. General Configuration Add remove some general configuration: Delete all add AddCRLF Add CR Add LF Add Tab Add Star(*) 12

14 2. Add prefix Prefix Switch Barcode: Prefix Prefix Prefix Content Add: Making Barcode Format:^3+PREFIX+content required add+(.) Reference Barcode as follows: 3. Add Suffix Suffix Switching Barcode: Suffix Suffix 13

15 Suffix Content Added: Making Barcode Format:^3+SUFFIX+content required add +(.) Reference Barcode as follows: 4. Display Scanner Serial Number Scan the following barcode to display scanner serial number: Display Serial Number 5. Display Software Version Number Scan the following barcode to display scanner software version number: Display software version number 14

16 Chapter5 Barcode Type 1. 1D Barcode 1.1 Interleaved 2 of 5( by Default) 1.2 China Post(Hong Kong)( by Default) 1.3 Matrix 2 of 5( by default) 15

17 1.4 Codabar( by default) 1.5 MSI(Plessey)( by default) 1.6 Code 128( by default) 1.7 Code 39( by Default) 16

18 1.8 Code 93( by Default) 1.9 Standard(IATA,Airline) 2 of 5(two-bar start/stop)( by Default) 1.10 Industrial 2 of 5 (three-bar start/stop)( by default) 1.11 GS1 DataBar (RSS)( by default) 17

19 1.12 Telepen( by default) 1.13 Trioptic Code( by default) Clsoe 1.14 UPC-A/EAN13( by default) 18

20 1.15 Code 11( by default) 2. 2D Barcode 2.1 QR( by default) 2.2 Data Matrix( by default) 2.3 PDF417( by Default) 19

21 20

22 2.4 Aztec( by default) 2.5 Hanxin( by default) 21