MERLIN / PRIMA Patch Fittings

Transcription

1 Patch Fittings Merlin & Prima Series

2 In the field of architectural fittings for glass doors, provides high quality and total design flexibility for ease of installation, safety, security and functionality. Our standard fittings are designed to suit 8-15mm glass panels mm glass panel Use different thickness of gasket 15 & 19mm glass panel Use extended screws & pivots. Pivot point from side panel is either 55mm or 65mm. Door Weight Calculation To estimate glass panel weight, the basic formula to use will be: WIDTH (m) x HEIGHT (m) x 2.5 factor x glass thickness (mm) = Y kg Therefore, for a glass panel of 12mm thickness, 1.0m width and 2.7m height, the glass panel weight will be 1.0 x 2.7 x 2.5 x 12 = 81kgs. Fittings are designed to carry maximum weight up to 120kg but for door width exceeding 1100mm, it is practical to use door rails. Torque for Fixing Screws Apply torque on each screw in progressive order until all screws reach the same required torque almost together. Cap Screw M6 (4mm allen key) 10 Nmm Cap Screw M6 (5mm allen key) 15 Nmm Cap Screw M8 (5mm allen key) 20 Nmm Typical Assemblies

3 PD10 Bottom Patch with insert to suit TD800 or TD750 floor spring PD20 Top Patch with insert and nylon socket to suit PD24 top pivot

4 PD11 Bottom Patch (Variable) with insert to suit TD800 or TD750 floor spring PD21 Top Patch (Variable) with insert & nylon socket to suit PD24 top pivot

5 PD31 Overpanel Patch (Variable) with Ø15mm pivot PD12 Bottom Patch with PD15P ball bearing insert

6 PD22 Top Patch with square insert to suit OC700 Overhead concealed door closer PD30 Overpanel Patch with Ø15mm Pivot and M8 tapped hole at side Options: with M8 threaded rod and expansion bolt with backplate

7 PD40 Overpanel & Side Panel Patch with Ø15mm Pivot PD40S Overpanel & Side Panel Patch with stop insert

8 PD40 (90) Overpanel & 90 Side Panel Patch with Ø15mm pivot Options: Left Hand (LH) / Right Hand (RH) Note: Illustration shows PD40(90) LH (Left or Right is determined by view from outside) For overpanel patch For side panel patch PD41 Overpanel Patch & Side Panel Patch with Ø15mm pivot and fin fitting Options: Left Hand (LH) / Right Hand (RH) Note: Illustration shows PD41(LH) (Left or Right is determined by view from outside)

9 PD50 Double Overpanel Patch with Ø15mm pivot PD51 Double Overpanel Patch with Ø15mm pivot and fin fitting

10 PD63 Overpanel & Side Panel Patch PD63S Overpanel & Side Panel Patch with stop insert

11 PD70 Overpanel Patch PD70 (90) Angled Patch

12 PD70 (90) Angled Patch to suit 15mm to 19mm thick glass panel PD70 (135) Angled Patch

13 PD70DS Overpanel Patch PD71 Overpanel Patch with fin fitting

14 Patch Fittings PD71DS Overpanel Patch with two stop inserts and fin fitting PD80 Connector Patch

15 Patch Fittings PD81 : Connector Patch with fin fitting PD82 : Side Patch Options: with back plate

16 PD85 Connector Patch Options: M8 threaded rod & expansion bolt / back plate PD86 Hangar Patch Note: PD85 has different glass notch

17 PD88 Connector Patch PD88 Connector Patch

18 GK20 Double Overpanel Strike Box to suit PL50 corner lock GK30 Single Overpanel Strike Box with M8 threaded rod M8 tapped hole at side Options: M8 threaded rod & expansion bolt Back plate

19 GK40 Overpanel & Side Panel Strike Box to suit PL50 corner lock GK40S Overpanel & Side Panel Strike Box with Stopper to suit PL50 corner lock Options: Left Hand (LH) / Right Hand (RH)

20 GK41 Overpanel & Side Panel Strike Box with fin fitting to suit PL50 corner lock Options: Left Hand (LH) / Right Hand (RH) Note: Illustration shows GK41 (LH) (Left or Right is determined by view from outside) GK41S Overpanel & Side Panel with stop insert and fin fitting Options: Left Hand (LH) / Right Hand (RH) Note: Illustration shows GK41S (LH) (Left or Right is determined by view from outside)

21 PL50 Corner Lock with PL1 patch locker and PM88 Euro-profile key cylinder US50 Centre Lock with PL1 patch locker and PM88 Euro-profile key cylinder

22 GK50 Centre Strike Box to suit US50 center lock

23 PM10 Bottom Patch with insert to suit TD800 or TD750 floor spring PM20 Top Patch with insert and nylon socket to suit PD24 top pivot

24 PM30 Over Panel Patch with Ø15mm Pivot to suit PM20 top patch PM40 Round Connector Patch

25 GK34 Overpanel Strike Box to suit PL34 lock patch GK34S Overpanel Patch with stop insert

26 PL34 Lock Patch include PM88 Euro-profile key cylinder to suit GK34 strike box PL1 Patch Locker for PL50 & US50 lock patch 9137 Stainless Steel Keeper Cup

27 PD15 Floor Pivot maximum load capacity : 150kg PD15P (Ball Bearing) Insert & Floor Pivot maximum load capacity: 120kg PD15PT (Ball Bearing) Insert & Floor Pivot maximum load capacity : 120kg PM88 Euro-Profile Key Cylinder length: 60mm PM88T Euro-Profile Key Cylinder length: 60mm

28 PD24 : Top Pivot Dia. 15mm pivot PD24NS : Top Pivot Ø12mm pivot PD24R : Roller Pivot Ø15mm roller pivot

29 Accessories for framed or wooden door 9116 Walking Pivot with Ø12.5mm pivot and stainless steel plate 9117 Adjustable Top Centre 9123L Door Strap 9123 Door Strap

30 P&M E Finishes Polished Stainless Steel Satin Stainless Steel Related Products Material Aluminium Casting (Body) SUS304 Stainless Steel (Cover Plate) Note Please specify glass thickness at time of order if other than 12mm thickness Universal Door Closers Due to the company s policy of continuous product development and enhancement, the specifications and details contained in this brochure are subject to alteration without prior notice. The dimensions, details, specifications and statements made herein or by our representatives arising out of any enquiries are given for information purposes only. They are not intended to have any legal effect and the company will not be bound thereby. The company will only accept obligations which are expressly negotiated for, and agreed and incorporated into written agreements made specifically with its respective customers. Melosa Door Handles Gerda Vinyl Clip Seals