Hydraulic Hybrid Pumps T6H* Denison Vane Technology, variable and fixed displacement

Transcription

1 Hydraulic Hybrid Pumps T6H* Deiso Vae Techology, variable ad fixed displacemet

2 Cotets Series T6H, Deiso Hybrid Pump GENERAL Features... 3 Istructios... 3 Miimum & maximum speeds... 4 Pressure ratigs... 4 Primig at startig... 4 Miimum allowable ilet pressure... 5 Geeral characteristics... 5 Pump selectio : Routie ad example... 6 Itermittet pressure ratig... 6 Formulas... 7 Descriptio... 8 Applicatio advatages... 8 Cotrols C, F & L & X... 9 Hydraulic fluids Shafts T6H20B - T6H20C T6H20B - T6H20C T6H20B T6H20C Orderig code & Operatig characteristics Dimesios Techical data Techical data T6H29B - T6H29C T6H29B - T6H29C T6H29B T6H29C Orderig code & Operatig characteristics Dimesios Techical data Techical data T6H29D T6H29D T6H29D Orderig code & Operatig characteristics Dimesios Techical data T6H29DB T6H29DB T6H29DB Orderig code & Operatig characteristics Dimesios Techical data T6H20B - T6H20C T6H29B - T6H29C - T6H29D T6H29DB Portig diagrams Portig diagrams Portig diagrams

3 Features Series T6H, Deiso Hybrid Pump DESCRIPTION FEATURES GREAT FLOW HIGH PRESSURE FLEXIBILITY The hybrid pump is a combiatio of fixed displacemet vae pump B, C, D cartridges combied with a variable cartridge of PV20 or PV29 pisto pump. The cartridges are drive by a commo shaft without couplig i betwee they have a large commo suctio port ad two or three idepedat outlet ports : Oe for the pisto, oe or two for the vae pump. These pumps have very compact displacemet ad are uder all actual pump sizes of the market. T6H20B = 42,9 ml/rev variable + 5,8 to 50,0 ml/rev fixed T6H20C = 42,9 ml/rev variable + 10,8 to 100,0 ml/rev fixed T6H29B = 61,9 ml/rev variable + 5,8 to 50,0 ml/rev fixed T6H29C = 61,9 ml/rev variable + 10,8 to 100,0 ml/rev fixed T6H29D = 61,9 ml/rev variable + 47,6 to 158,0 ml/rev fixed T6H29DB = 61,9 ml/rev variable + 47,6 to 158,0 ml/rev fixed + 5,8 to 50,0 ml/rev fixed Cotiuous pressure ratigs for variable displacemet uits are 240 bar for T6H20B/C ad 210 bar for T6H29B/C/D/DB. This combied uit offers the advatage of low oise PV ad vae pump which together icrease safety ad better acceptace of workig coditios. System savig because high pressure allows the use of smaller compoets... you ca dow size ad gai real savigs. Both uits fixed flow ad variable flow havig separated outlets allow simultaeous machie cycles eg : Mobile machie steerig foctio workig at the same time as the hydraulic cyliders boom fuctios. - Oe Commo suctio port. - P2 rear port 4 or 8 positios - P3 rear port 8 positios. - Optioal iteral drai for variable pisto pump. - Compesator vetig valve itegrated. Cotrol optios o variable displacemet (pisto pump). - Compesator C - Vetable pressure compesator F - Load sesig compesator L - Compesator with electric vet valve (oly ext. drai) X (oly T6H20B ad T6H20C as stadard) Vae pump cartridge allows great flexibility with may differet displacemets with easy coversio or reewal. Wide rage of acceptable fluids from 1600 to 10 cst ca operate with mieral oil, biodegradable oil, ad fire resistat fluids. GENERAL APPLICATIONS INSTRUCTIONS 1. Check speed rage, pressure, temperature, fluid quality, viscosity ad pump rotatio. 2. T6H pump case pressure should ot exceed 0,7 bar (see datas). 3. Check ilet coditios of the pump, if it ca accept applicatio requiremet. 4. Type of shaft : if it would support operatig torque. 5. Couplig must be chose to miimize pump shaft load (weight, misaligmet). 6. Filtratio : must be adequate for lowest cotamiatio level. 7. Eviromet of pump : to avoid oise reflectio, pollutio ad shocks. 8. Although the T6H pumps have fast off stroke compesator repose, system relief valves are recommeded for safety cosideratios. 9. Whe costatly uder pressure with o flow requiremets, it is safer to flush the pisto pump. Three drais holes are there for this purpose. 3

4 Speed ad Pressure Ratigs Series T6H, Deiso Hybrid Pump Theoretical Maximum Speed Maximum Pressure Miimum Displacemet Port Size Series Speed HF-0,HF-1 HF-3, HF-4 HF-0, HF-2 HF-1, HF-4, HF-5 HF-3 Vi HF-2 HF-5 It. 3) Cot. It. 3) Cot. It. 3) Cot. ml/rev. RPM RPM RPM bar bar bar bar bar bar P1 T6H20 42, ) ) 140 2) T6H29 61, ) ) 140 2) B02 5,8 B03 9,8 B04 12,8 P2 B05 15,9 or B B06 19,8 B07 22, P3 B08 24,9 B10 31,8 B12 41,0 B15 50, *03 10,8 P2 C D *05 17,2 *06 21,3 *08 26,4 *10 34,1 *12 37,1 *14 46,0 *17 58,3 *20 63,8 *22 70,3 *25 79,3 600 (400) (mobile) *28 88, *31 100, , , , , , , , , , , , * = 0 : Idustrial applicatio = B : Idustrial bi-rotatioal = M : Mobile applicatio 1) See page 11 for max. pressure f(). 2) Max. pressure HF-1 same as HF-0 ad HF-2. 3) See page 6 for coditios. HF-0, HF-2 = Atiwear Petroleum Base HF-1 = No Atiwear Petroleum Base HF-5 = Sythetic Fluids HF-3 = Water i oil Emulsios HF-4 = Water Glycols For further iformatio or if the performace characteristics outlied above do ot meet your ow particular requiremets, please cosult your local Parker represetative. PRIMING AT STARTING At first start operatio of the pump, ru it at the lowest speed ad at the lowest pressure to obtai primig. Whe a pressure relief valve is used at the outlet it should be backed off to miimize retur pressure. A air bleed off should be provided i the circuit to facilitate the primig. Never operate pump shaft at top speed ad pressure without checkig for completio of pump primig, ad that the fluid is ot aerated. Always fill the housig of the T6H with oil of circuit prior to start up. 4

5 Mi allowable ilet pressure Series T6H, Deiso Hybrid Pump Cartridge Speed RPM Size Series B C D Series T6H20 0,80 0,80 0,80 0,80 0,80 0,85 0,90 T6H20 T6H29 0,80 0,80 0,80 0,86 1,00 1,04 T6H29 B02 B03 B04 B05 B06 B07 B08 B10 B12 0,80 0,80 0,80 0,80 0,80 0,80 0,80 B15 0,84 B15 *03 *05 *05 *06 0,80 0,90 *06 *08 0,80 *08 *10 0,80 *10 *12 *14 0,80 0,80 0,80 0,85 B02 B03 B04 B05 B06 B07 B08 B10 B12 *03 0,92 *12 *17 0,95 *17 0,85 *20 0,90 *20 *22 0,85 0,90 0,98 *22 *25 0,95 0,95 *25 0,90 *28 0,98 0,98 *28 *31 0,85 0,90 1,00 * ,80 1, ,88 0, ,82 1, ,80 0,85 0,92 1, , ,80 0,80 0,90 0,95 1, ,92 0,98 1,02 1, ,00 1, , ,02 1, ,85 0,98 1, ,02 1, T6H20 Max. case P 0,69 0,69 0,69 0,34 0,34 0,34 0,34 T6H20 T6H29 (bar relative) 0,69 0,69 0,69 0,34 0,34 0,34 T6H29 Vae cartridge : Ilet pressure is measured at ilet flage with petroleum base fluids at viscosity betwee 10 ad 65 cst. The differece betwee ilet pressure (at the pump flage) ad atmospheric pressure must ot exceed 0,2 bar absolute to prevet aeratio. Pisto cartridge : Rapid compesatio at high speeds ca cause severe case spikes. If the pump feeds ito a blocked ceter valve that close quickly, use both case drai ports ad direct short case drai lies ad a relief valve. Multiply absolute pressure by 1,25 for HF-3, HF-4 fluids. by 1,35 for HF-5 fluid. by 1,10 for ester or rapeseed base. GENERAL CHARACTERISTICS Weight without SAE 4 bolts J518c Moutig stadard coector ad ISO/DIS or Momet of iertia bracket - kg kg m 2 x 10-4 Suctio Pressure P1 Pressure P2 Pressure P3 T6H20B SAE J744c 37,0 42,9 ISO SAE B T6H20C ,0 46,7 2.1/2 3/4" or 1" T6H29B 49,0 64,2 1.1/4 T6H29C SAE J744c 49,0 68,0 ISO SAE C T6H29D ,0 80,7 3" 1.1/4 T6H29DB 72,0 83,9 3/4" or 1" *

6 Pump Selectio Series T6H, Deiso Hybrid Pump CALCULATION To resolve Volumetric displacemet Vi [m/rev.] Available flow Q [l/mi] Iput Power P [Kw] Performaces required - (P1 - P2) Requested flow Q [l/mi] 60 Speed [R.P.M.] ROUTINE AND EXAMPLE Routie : Example : 1. First calculatio Vi = 1000 Q Vi = 1000 x = 40 ml/rev. 2. Choice Vi of each sectio of pump immediately greater P1 = Pisto cartridge T6H20 P2 = Vae cartridge (see tabulatio) the the pump will be 3. Theoretical flow of this pump Q theo. = Vi x Available flow P1 - Cosult the curve Full flow P2- Fid qs leakage fuctio of pressure qs = f(p) o curve at 10 or 24 cst Q = Q theo. - qs 5. Theoretical iput power P1 : Pisto sectio - Cosult curve Q P2 : theo. x p Fid Ps hydrodyamic power loss o curve 7. Total iput power P = P (P1) + P (P2) + Ps Stage P1 : T6H20 Vi = 42,9 ml/rev. Stage P2 : Size C 014 Vi = 46,0 ml/rev. T6H20C Stage P1 : Q theo = Stage P2 : Q theo = 42,9 x x = 64,35 l/mi = 69 l/mi Stage P1 : 1500 R.P.M. at 150 bar = 62 l/mi T6H20C (page 15) : Stage P2 : qs = 5 l/mi at 150 bar, 24 cst Stage P2 : Q = 69-5 = 64 l/mi T6H20C (page 15) Stage P1 : Curve Ilet horsepower 1500 R.P.M. at 150 bar = 18 kw 69 x 150 Stage P2 : = 17,3 kw 600 T6H20C (page 15) : Ps at 1500 R.P.M., 150 bar = 1.5 kw P = ,3 + 1,5 = 36,8 kw 8. Results T6H20C P1 Vi = 42,9 ml/rev Q = 62,0 l/mi Iput horsepower P2 Vi = 46,0 ml/rev Q = 64,0 l/mi p = 36,8 kw INTERMITTENT PRESSURE RATING Pressure (bar) Average Pressure cycle Time (miutes) Pisto cartridge sectio (P1) may be operated at a itermittet pressure but 10% of operatio time oly, ot exceedig 6 successive secods. Vae cartridge sectio uits may be operated itermittetly at pressures higher tha the recommeded cotiuous ratig whe the time weighted average of pressure is less tha or equal to the cotiuous duty pressure ratig. This itermittet pressure ratig calculatio is oly valid if other parameters; speed, fluid, viscosity ad cotamiatio level are respected. For total cycle time higher tha 15 miutes please cosult your Parker represetative. Example : T6H20C P2 - Duty cycle 4 mi. at 275 bar 1 mi. at 35 bar 5 mi. at 160 bar (4 x 275) + (1 x 35) + (5 x 160) = 193,5 bar ,5 bar is lower tha 240 bar allowed as cotiuous pressure for T6H20C with HF-0 fluid. 6

7 Formulas Series T6H, Deiso Hybrid Pump FLUID POWER FORMULAS Pump iput torque Pump iput power N.m kw pressure (bar) x displacemet (ml/rev) 20 π x mech. eff. speed (rpm) x displacemet (ml/rev) x pressure (bar) x overall eff. Pump output flow Fluid motor speed Fluid motor torque Fluid motor power Lpm rpm N.m kw speed (rpm) x displacemet (ml/rev) x volumetric eff x flow rate (Lpm) x volumetric eff. displacemet (ml/rev.) pressure (bar) x displacemet (ml/rev) x mech. eff. 20 π speed (rpm) x displacemet (ml/rev) x pressure (bar) x overall eff

8 Descriptio Series T6H, Deiso Hybrid Pump Cap ed outlet port has 4 or 8-positios at 45 or 90 itervals relative to ilet. Cotrol for pisto cartridge. Pisto ad shoe. Hager. Frot sideplate is clamped axially by discharge pressure to reduce iteral leakage. Heavy duty tapered roller bearig. Cartridges are replaceable assemblies. Each icludes cam rig, rotor, vaes, pis ad sideplates. Shaft comes i variety of keyed ad splied optios to meet SAE ad ISO Vae is urged outward at suctio ramp by pi force ad cetrifugal force. Pi cavity is at a steady pressure slightly higher tha at discharge port. MOBILE VERSION 90 sectio Sectio B-B Holes i cam rig improve wide cartridge ilet characteristics. Suctio ramp where uloaded vae moves out. Barrel. Workig vae o major arc pushes fluid to discharge port. Sectio A-A Vae is urged outward at suctio ramp by pi force ad cetrifugal force Pi cavity is at a steady pressure equal to that at discharge port. Lub side holes lubricate the sideplate surfaces. INDUSTRIAL VERSION 90 sectio Sectio B-B Discharge ramp where uloaded vae moves i. Suctio ramp where uloaded vae moves out. Holes i cam rig improve wide cartridge ilet characteristics Workig vae o mior arc seals discharge pressure from the suctio port. Workig vae o major arc pushes fluid to discharge port. Sectio A-A Side feed holes supply discharge pressure to pi cavities. Discharge ramp where uloaded vae moves i. Workig vae o mior arc seals discharge pressure from the suctio port. APPLICATION ADVANTAGES The high pressure capability to 240 bar, i the small evelope, reduces istallatio costs ad provides exteded life at reduced pressure. The high volumetric efficiecy, typically 94%, reduces heat geeratio, ad allows speeds dow to 600 RPM (400 RPM for mobile) at full pressure. The high mechaical efficiecy, typically 94%, reduces eergy cosumptio. The wide speed rage from 600 RPM to 2600 RPM (400 RPM to 2600 RPM for mobile), combied with large size cartridge displacemets, will optimize operatio for the lowest oise level i the smallest evelope. The low speed 600 RPM (400 RPM for mobile), low pressure, high viscosity 860 cst (1600 cst for mobile) allow applicatio i cold eviromets with a miimum eergy cosumptio ad without of seizure risk. The low ripple pressure ± 2 bar reduces pipig oise ad icreases life time of the other compoets i the circuit. The high resistace to particle cotamiatio because of the double lip vae icreases pump life. The large variety of optios (cam displacemet, shaft, portig, pisto sectio cotrols) allows customized istallatio. 8

9 Cotrols C - COMPENSATOR The C ad F pressure compesator cotrol allows the pump to deliver full volume from the outlet port util the pressure rise to the value set by the cotrol. The cotrol the reduces the pump volume to that required by the system mobile maiteig the preset pressure at the outlet port. Series T6H, Deiso Hybrid Pump Compesator adjustemet F - VENTABLE COMPENSATOR The F compesator is used i applicatios requirig remote cotrol pressure. The remote relief is coected to the vet port. The pressure may be cotrolled at ay level below the compesator pressure settig. The vet port may also be used to remotely vet-off the compesator for startig. Compesator adjustemet Vet valve Differetial pressure adjustemet (17-28 bar) L - LOAD SENSING COMPENSATOR The L compesator is used for load sesig circuits ad is a true load esor. This is the F compesator with a pi i the compesator spool (see elarged view). The pi prevets pilot flow from eterig the circuit which will elimiate creepig of the load. The L compesator will let the pump deliver a costat flow rate to the circuit by providig a adjustable ΔP across the customers orifice or valve. The pump will operate at bar above Load Pressure. Compesator adjustemet Differetial pressure adjustemet (17-28 bar) Load Pi X - VENTED COMPENSATOR BY ELECTRIC VALVE The X compesator is used i applicatio requirig vet off o compesator at startig or at other time of the cycle. The pisto cartridge reduce the volume for maiteig the pressure at the differetial pressure settig. Compesator adjustemet Electric vet valve (mouted o the port block) Differetial pressure adjustemet (17-28 bar) 9

10 Fluids FLUIDS RECOMMENDED FLUIDS ACCEPTABLE ALTERNATE FLUIDS VISCOSITY Series T6H, Deiso Hybrid Pump Petroleum based atiwear R & O fluids. These fluids are the recommeded fluids for T6 series pumps. Maximum catalogue ratigs ad performace data are based o operatio with these fluids. These fluids are covered by Deiso HF-0 ad HF-2 specificatio. The use of fluids other tha petroleum based atiwear R & O fluids, requires that the maximum ratigs of the pumps will be reduced. I somes cases the miimum repleishmet pressures must be icreased. Cosult specific sectios for more details. Max (cold start, low speed & pressure) 860 mm 2 /s (cst) Max (cold start, low speed & pressure) (for mobile) 1600 mm 2 /s (cst) Max (full speed & pressure) 108 mm 2 /s (cst) Optimum (max. life) 30 mm 2 /s (cst) Mi (full speed & pressure for HF-1, HF-3, HF-4 & HF-5 fluids) 18 mm 2 /s (cst) Mi (full speed & pressure for HF-0 & HF-2 fluids) 13 mm 2 /s (cst) VISCOSITY INDEX 90 mi. higher values exted rage of operarig temperatures. Maximum fluid temperature (θ) C HF-0, HF-1, HF-2 HF-3, HF-4 HF-5 Biodegradable fluids (esters & rapeseed base) C + 50 C + 70 C + 65 C Miimum fluid temperature (θ) C HF-0, HF-1, HF-2, HF-5-18 C HF-3, HF C Biodegradable fluids (esters & rapeseed base) - 20 C FLUID CLEANLINESS OPERATING TEMPERATURES AND VISCOSITIES WATER CONTAMINATION IN THE FLUID The fluid must be cleaed before ad durig operatio to maitai cotamiatio level of NAS 1638 class 8 (or ISO 19/17/14) or better. Filters with 25 micro (or better, ß10 100) omial ratigs may be adequate but do ot guaratee the required clealiess levels. Suctio straiers must be of adequate size to provide miimum ilet pressure specified. 100 mesh (149 micro) is the fiest mesh recommeded. Use oversize straiers or omit them altogether o applicatios which require cold starts or use fire resistat fluids. Operatig temperatures are a fuctio of fluid viscosities, fluid type, ad the pump.fluid viscosity should be selected to provide optimum viscosity at ormal operatig temperatures. For cold starts the pumps should be operated at low speed ad pressure util fluid warms up to a acceptable viscosity for full power operatio. Maximum acceptable cotet of water. 0.10% for mieral base fluids. 0.05% for sythetic fluids, crakcase oils, biodegradable fluids. If amout of water is higher the it should be draied off the circuit. 10

11 Shafts Series T6H, Deiso Hybrid Pump SHAFTS COUPLINGS AND FEMALE SPLINES SPLINES KEYED SHAFTS NOTE SHAFT LOADS SHAFT BEARING LIFE (TYPICAL) WITHOUT EXTERNAL LOAD The shafts will accept a maximum misaligmet of 0.06 TIR whe the pump is foot mouted ad 0.03 mm whe flage mouted. The agular aligmet of two splie axes must be less tha 0.1 (0.002 mm/mm). The couplig splie must be lubricated with a lithium molydisulfide grease or a similar lubricat. The couplig must be hardeed to a hardess betwee 27 ad 45 R.C. The female splie must be made to coform to the Class 1 fit as described i SAE-J498b (1971). This is described as a Flat Root Side Fit. We supply the T6H series keyed shaft pumps with high stregth heat-treated keys. Therefore, whe istallig or replacig these pumps, the heat-treated keys must be used i order to isure maximum life i the applicatio. If the key is replaced it must be a heat-treated key betwee 27 ad 34 R.C. hardess. The corers of the keys must be chamfered from 0.76 to 1.02 at 45 to clear radius i the key way. Aligmet of keyed shafts must be withi toleraces give for splied shafts. These products are desiged primarily for coaxial drives which do ot impose axial or side loadig o the shaft. Cosult the typical curve below for the theorical life. For specific applicatios which may iclude vibratio ad stock durig operatio of the machie or exteral load o the drive shaft. Please cosult your local Parker represetative T6H20 MAX. INTERMITTENT PRESSURE MAX. CONTINUOUS PRESSURE L10h = hours L10h = hours L10h = hours L10h = hours 13 cst Mi. P1 Full displacemet Speed [RPM] T6H29 MAX. INTERMITTENT PRESSURE MAX. CONTINUOUS PRESSURE L10h = hours L10h = hours L10h = hours L10h = hours 13 cst Mi. P1 Full displacemet Speed [RPM] 11

12 Orderig Code ad Characteristics Series T6H20B, T6H20C, Deiso Hybrid Pump Model No. T6H20B - B08-1 L 1 B - 2 F 0 M T6H20C - *12-1 L 1 C - 2 F 0 M Series ad capacity P1 (rotatig group) 42,9 ml/rev. Cam rig P2 (Delivery at 0 bar & 1500 r.p.m.) T6H20B T6H20C B02 = 8,7 l/mi *03 = 16,2 l/mi B03 = 14,7 l/mi *05 = 25,8 l/mi B04 = 19,2 l/mi *06 = 31,9 l/mi B05 = 23,9 l/mi *08 = 39,6 l/mi B06 = 29,7 l/mi *10 = 51,1 l/mi B07 = 33,7 l/mi *12 = 55,6 l/mi B08 = 37,4 l/mi *14 = 69,0 l/mi B10 = 47,7 l/mi *17 = 87,4 l/mi B12 = 61,5 l/mi *20 = 95,7 l/mi B15 = 75,0 l/mi *22 = 105,4 l/mi *25 = 118,9 l/mi *28 = 133,2 l/mi *31 = 150,0 l/mi Type of shaft 1 = keyed (SAE BB) 3 = splied (SAE C) 4 = splied (SAE BB) 5 = keyed (SAE C) Direct. of rotatio (view o shaft ed) R = clockwise L = couter-clockwise Seal class 1 = S1 BUNA N 5 = S5 VITON Desig letter B = T6H20B C = T6H20C * = 0 = Idust. ui-rotatioal / B = Idust. bi-rotatioal / M = Mobile bi-rotatioal OPERATING CHARACTERISTICS - TYPICAL [24 cst] Pressure port P2 T6H20B P2 T6H20C Series Volumetric Displacemet Vi Modificatio Portig combiatio Deped o the rotatio - See page 26 Variables port Dia Code P2 1" 0 P2 3/4" 1 Variables flages coectios 4 bolts SAE flage (J518c) 0 = UNC thread M = metric thread) Cotrol accessories 0 = Maxi flow 9 = 90% maxi flow 8 = 80% maxi flow 7 = 70% maxi flow 6 = 60% maxi flow 5 = 50% maxi flow Cotrol C = Compesator F = RC pilot operated compesator L = RC pilot operated compesator load sesig X* = RC pilot operated compesator with vet valve 24 VDC * Use with exteral drai oly Coectio (drai + vet.) 0 = ext. drai + UNF thread 2 = ext. drai + BSPP thread 3 = it. drai + UNF thread 4 = it. drai + BSPP thread Flow Q [l/mi], = 1500 RPM Iput power P [kw], = 1500 RPM p = 0 bar p = 140 bar p = 300 bar p = 7 bar p = 140 bar p = 300 bar B02 5,8 ml/rev 8,7 7,0 5,1 0,5 2,6 5,1 B03 9,8 ml/rev 14,7 13,0 11,1 0,6 4,0 8,1 B04 12,8 ml/rev 19,2 17,5 15,6 0,6 5,0 10,4 B05 15,9 ml/rev 23,9 22,2 20,2 0,7 6,1 12,7 B06 19,8 ml/rev 29,7 28,0 26,1 0,7 7,5 15,6 B07 22,5 ml/rev 33,7 32,0 30,2 0,8 8,5 17,6 B08 24,9 ml/rev 37,4 35,7 33,7 0,8 9,3 19,5 B10 31,8 ml/rev 47,7 46,0 44,1 0,9 11,7 24,6 B12 41,0 ml/rev 61,5 59,8 57,9 1,2 14,9 31,5 B15 50,0 ml/rev 75,0 73,3 71,6 1) 1,3 18,1 35,7 1) p = 0 bar p = 140 bar p = 240 bar p = 7 bar p = 140 bar p = 240 bar Idust. Mobile Idust. Mobile *03 10,8 ml/rev 16,2 11,2 10,7 7,7-1,3 5,3 8,4 *05 17,2 ml/rev 25,8 20,8 20,3 17,3 15,8 1,4 7,5 12,2 *06 21,3 ml/rev 31,9 26,9 26,4 23,4 21,9 1,5 8,9 14,7 *08 26,4 ml/rev 39,6 34,6 34,1 31,1 29,6 1,6 10,7 17,7 *10 34,1 ml/rev 51,1 46,1 45,6 42,6 41,1 1,7 13,4 22,3 *12 37,1 ml/rev 55,6 50,6 50,1 47,1 45,6 1,7 14,4 24,1 *14 46,0 ml/rev 69,0 64,0 63,5 60,5 59,0 1,9 17,6 29,5 *17 58,3 ml/rev 87,4 82,4 81,9 78,9 77,4 2,1 21,9 36,9 *20 63,8 ml/rev 95,7 90,7 90,2 87,2 85,7 2,2 23,8 40,2 *22 70,3 ml/rev 105,4 100,4 99,9 96,9 95,4 2,3 26,1 44,1 *25 79,3 ml/rev 118,9 113,9 113,4 110,4 108,9 2,5 29,2 49,5 *28 88,8 ml/rev 133,2 128,2 127,7 125,8 2) 124,5 2) 2,8 32,7 48,5 2) *31 100,0 ml/rev 150,0 145,0 144,5 142,6 2) 141,3 2) 2,8 36,5 54,4 2) 1) B15 = 280 bar max. it. 2) = 210 bar max. it. - Not to use because iteral leakage greater tha 50% theoretical flow. 12

13 Dimesios - Weight : 37,0 kg Series T6H20B, T6H20C, Deiso Hybrid Pump TYPE: X VP VENT PORT 1/4 BSPP OR SAE-4 FOR F OR L CONTROL DR DRAIN PORT 1/2 BSPP OR SAE-8 (PLUGGED FOR INTERNAL DRAIN) TUBE & FITTING FOR CONTROL X WITH ELECTRIC VENT VALVE ONLY. ELECTRIC VENT VALVE (SHOW FOR CCW ROT) VENT TYPE: F & L TYPE: C KEY 7,94 7,89 M8 x 16 DEEP 35,27 MAXI Shaft code 5 KEYED SAE C-SHORT (M10 x 19 DEEP-METRIC VERSION) 3/8-16 UNC x 19 DEEP (M12 x 16 DEEP-METRIC VERSION) 1/2-13 UNC x 16 DEEP (M12 x 24 DEEP-METRIC VERSION) 7/16-14 UNC x 24 DEEP TYPE F & X TYPE L OPTIONAL AUXILIARY ELECTRIC VENT VALVE FOR X CONTROL P1 Ø 31,8 for CCW ROT S Ø 63,5 for CW ROT SIDE OF CONTROLS FOR CCW ROTATION KEY 6,35 6,30 M8 x 16 DEEP 28,22 MAX INTERNAL ALTERNATE DRAIN HYDRAULIC CIRCUIT (SHOWED FOR F L OR X CONTROL) MOUNTING TORQUE 80 Nm MOUNTING TORQUE 110 Nm EXTERNAL (PREFERED) Shaft torque limits [ml/rev. x bar] P1 Ø 31,8 for CW ROT S Ø 63,5 for CCW ROT Shaft Vi x p max MOUNTING TORQUE 41 Nm Shaft code 1 KEYED SAE BB SIDE OF CONTROLS FOR CW ROTATION Variable port Port Code A B Ø C P2 0 52,4 26,2 25,4 P2 1 47,7 22,4 19,0 Shaft code 3 INVOLUTE SPLINE SAE C FLAT ROOT - SIDE FIT J498b-CLASS, 1-PITCH, 12/24 14 TEETH - PRESS. ANGLE: 30 Shaft code 4 INVOLUTE SPLINE SAE BB FLAT ROOT - SIDE FIT J498b-CLASS, 1-PITCH, 16/32 15 TEETH - PRESS. ANGLE: 30 13

14 Techical Data Series T6H20B, Deiso Hybrid Pump Power loss Ps [kw] Iteral leakage qs [l/mi] INTERNAL LEAKAGE (TYPICAL) P2 CARTRIDGE Do ot operate pump more tha 5 secods at ay speed or viscosity if iteral leakage is higher tha 50% of theoretical flow. HYDROMECHANICAL POWER LOSS (TYPICAL) P2 CARTRIDGE = 2600 RPM = 1500 RPM [24 cst] Lp. Noise level [db(a)] 1m ISO 4412 Flow [l/mi] NOISE LEVEL (TYPICAL) T6H20B - B03 Pe = 0,9 bar abs = 1500 RPM Lw = Lp + 8 db (A) Noise level is give with each cartridge dischargig at the pressure oted o the curve (P1 full flow). ν OUTLET FLOW P1 CARTRIDGE = 1000 RPM = 1500 RPM = 1800 RPM = 2400 RPM = 24 cst OVERALL EFFICIENCY - P1 CARTRIDGE Full displacemet INPUT HORSEPOWER - P1 CARTRIDGE Full displacemet Efficiecy [%] = 1500 RPM = 1800 RPM = 2400RPM Horse power [kw] = 1500 RPM = 1800 RPM = 2400 RPM 14

15 Techical Data Series T6H20C, Deiso Hybrid Pump Power loss Ps [kw] Iteral leakage qs [l/mi] INTERNAL LEAKAGE (TYPICAL) P2 CARTRIDGE Do ot operate pump more tha 5 secods at ay speed or viscosity if iteral leakage is higher tha 50% of theoretical flow. HYDROMECHANICAL POWER LOSS (TYPICAL) P2 CARTRIDGE = 2600 RPM = 1500 RPM [24 cst] Lp. Noise level [db(a)] 1m ISO 4412 Flow [l/mi] NOISE LEVEL (TYPICAL) T6H20C - B22 Pe = 0,9 bar abs = 1500 RPM Lw = Lp + 8 db (A) Noise level is give with each cartridge dischargig at the pressure oted o the curve (P1 full flow). ν OUTLET FLOW P1 CARTRIDGE = 1000 RPM = 1500 RPM = 1800 RPM = 2400 RPM = 24 cst OVERALL EFFICIENCY - P1 CARTRIDGE Full displacemet INPUT HORSEPOWER - P1 CARTRIDGE Full displacemet Efficiecy [%] = 1500 RPM = 1800 RPM = 2400RPM Horse power [kw] = 1500 RPM = 1800 RPM = 2400 RPM 15

16 Orderig Code ad Characteristics Series T6H29B, T6H29C, Deiso Hybrid Pump Model No. T6H29B - B08-1 L 1 B - 2 F 0 M T6H29C - *12-1 L 1 C - 2 F 0 M Series ad capacity P1 (rotatig group) 61,9 ml/rev. Cam rig P2 (Delivery at 0 bar & 1500 r.p.m.) T6H29B T6H29C B02 = 8,7 l/mi *03 = 16,2 l/mi B03 = 4,7 l/mi *05 = 25,8 l/mi B04 = 19,2 l/mi *06 = 31,9 l/mi B05 = 23,9 l/mi *08 = 39,6 l/mi B06 = 29,7 l/mi *10 = 51,1 l/mi B07 = 33,7 l/mi *12 = 55,6 l/mi B08 = 37,4 l/mi *14 = 69,0 l/mi B10 = 47,7 l/mi *17 = 87,4 l/mi B12 = 61,5 l/mi B15 = 75,0 l/mi *20 = 95,7 l/mi *22 = 105,4 l/mi *25 = 118,9 l/mi *28 = 133,2 l/mi *31 = 150,0 l/mi Type of shaft 1 = keyed (SAE C) 4 = splied (SAE C) Direct. of rotatio (view o shaft ed) R = clockwise L = couter-clockwise Seal class 1 = S1 BUNA N 5 = S5 VITON Desig letter * = 0 = Idust. ui-rotatioal / B = Idust. bi-rotatioal / M = Mobile bi-rotatioal OPERATING CHARACTERISTICS - TYPICAL [24 cst] Pressure port P2 T6H29B P2 T6H29C Series Volumetric Displacemet Vi Modificatio Portig combiatio Deped o the rotatio - See page 26 Variable port Dia Code P2 1" 0 P2 3/4" 1 Variables flages coectios 4 bolts SAE flage (J518c) 0 = UNC thread M = metric thread) Cotrol accessories 0 = Maxi flow 9 = 90% maxi flow 8 = 80% maxi flow 7 = 70% maxi flow 6 = 60% maxi flow 5 = 50% maxi flow Cotrol C = Compesator F = RC pilot operated compesator L = RC pilot operated compesator load sesig Coectio (drai + vet.) 0 = ext. drai + UNF thread 2 = ext. drai + BSPP thread 3 = it. drai + UNF thread 4 = it. drai + BSPP thread Flow Q [l/mi], = 1500 RPM Iput power P [kw], = 1500 RPM p = 0 bar p = 140 bar p = 300 bar p = 7 bar p = 140 bar p = 300 bar B02 5,8 ml/rev 8,7 7,0 5,1 0,5 2,6 5,1 B03 9,8 ml/rev 14,7 13,0 11,1 0,6 4,0 8,1 B04 12,8 ml/rev 19,2 17,5 15,6 0,6 5,0 10,4 B05 15,9 ml/rev 23,9 22,2 20,2 0,7 6,1 12,7 B06 19,8 ml/rev 29,7 28,0 26,1 0,7 7,5 15,6 B07 22,5 ml/rev 33,7 32,0 30,2 0,8 8,5 17,6 B08 24,9 ml/rev 37,4 35,7 33,7 0,8 9,3 19,5 B10 31,8 ml/rev 47,7 46,0 44,1 0,9 11,7 24,6 B12 41,0 ml/rev 61,5 59,8 57,9 1,2 14,9 31,5 B15 50,0 ml/rev 75,0 73,3 71,6 1) 1,3 18,1 35,7 1) p = 0 bar p = 140 bar p = 240 bar p = 7 bar p = 140 bar p = 240 bar Idust. Mobile Idust. Mobile *03 10,8 ml/rev 16,2 11,2 10,7 7,7-1,3 5,3 - *05 17,2 ml/rev 25,8 20,8 20,3 17,3 15,8 1,4 7,5 12,2 *06 21,3 ml/rev 31,9 26,9 26,4 23,4 21,9 1,5 8,9 14,7 *08 26,4 ml/rev 39,6 34,6 34,1 31,1 29,6 1,6 10,7 17,7 *10 34,1 ml/rev 51,1 46,1 45,6 42,6 41,1 1,7 13,4 22,3 *12 37,1 ml/rev 55,6 50,6 50,1 47,1 45,6 1,7 14,4 24,1 *14 46,0 ml/rev 69,0 64,0 63,5 60,5 59,0 1,9 17,6 29,5 *17 58,3 ml/rev 87,4 82,4 81,9 78,9 77,4 2,1 21,9 36,9 *20 63,8 ml/rev 95,7 90,7 90,2 87,2 85,7 2,2 23,8 40,2 *22 70,3 ml/rev 105,4 100,4 99,9 96,9 95,4 2,3 26,1 44,1 *25 79,3 ml/rev 118,9 113,9 113,4 110,4 108,9 2,5 29,2 49,5 *28 88,8 ml/rev 133,2 128,2 127,7 125,8 2) 124,5 2) 2,8 32,7 48,5 2) *31 100,0 ml/rev 150,0 145,0 144,5 142,6 2) 141,3 2) 2,8 36,5 54,4 2) 1) B15 = 280 bar max. it. 2) = 210 bar max. it. - Not to use because iteral leakage greater tha 50% theoretical flow. 16

17 Dimesios - Weight : 49,0 kg Series T6H29B, T6H29C, Deiso Hybrid Pump VP VENT PORT 1/4 BSPP OR SAE-4 FOR F OR L CONTROL DR DRAIN PORT 1/2 BSPP OR SAE-8 (PLUGGED FOR INTERNAL DRAIN) TYPE: F & L TYPE: C TYPE F TYPE L (M10 x 19 DEEP-METRIC VERSION) 3/8-16 UNC x 19 DEEP - 4-HOLES MOUNTING TORQUE 80 Nm (M12 x 22 DEEP-METRIC VERSION) 1/2-13 UNC x 22 DEEP - 4-HOLES P1 Ø 31,8 for CCW ROT S Ø 63,5 for CW ROT (M12 x 24 DEEP-METRIC VERSION) 7/16-14 UNC x 24 DEEP-4 HOLES SIDE OF CONTROLS FOR CCW ROTATION Shaft code 3 INVOLUTE SPLINE SAE C FLAT ROOT - SIDE FIT J498b-CLASS, 1-PITCH, 12/24 14 TEETH - 30 PRESS. ANGLE KEY 7,94 7,89 M10 x 20 DEEP 35,27 MAXI INTERNAL ALTERNATE DRAIN HYDRAULIC CIRCUIT (SHOWED FOR F OR L CONTROL) EXTERNAL (PREFERED) MOUNTING TORQUE 180 Nm P1 Ø 31,8 for CW ROT S Ø 63,5 for CCW ROT MOUNTING TORQUE 41 Nm SIDE OF CONTROLS FOR CW ROTATION Shaft code 1 KEYED SAE C Variable port Port Code A B Ø C P2 0 52,4 26,2 25,4 P2 1 47,7 22,4 19,0 17

18 Techical Data Series T6H29B, Deiso Hybrid Pump Power loss Ps [kw] Iteral leakage qs [l/mi] INTERNAL LEAKAGE (TYPICAL) P2 CARTRIDGE Do ot operate pump more tha 5 secods at ay speed or viscosity if iteral leakage is higher tha 50% of theoretical flow. HYDROMECHANICAL POWER LOSS (TYPICAL) P2 CARTRIDGE = 2400 RPM = 1500 RPM [24 cst] Lp. Noise level [db(a)] 1m ISO 4412 Flow [l/mi] NOISE LEVEL (TYPICAL) T6H29B - B03 Pe = 0,9 bar abs = 1500 RPM Lw = Lp + 8 db (A) Noise level is give with each cartridge dischargig at the pressure oted o the curve (P1 full flow). ν OUTLET FLOW P1 CARTRIDGE = 1000 RPM = 1500 RPM = 1800 RPM = 2400 RPM = 24 cst OVERALL EFFICIENCY - P1 CARTRIDGE Full displacemet INPUT HORSEPOWER - P1 CARTRIDGE Full displacemet Efficiecy [%] = 1500 RPM = 1800 RPM = 2400RPM Horse power [kw] = 1500 RPM = 1800 RPM = 2400 RPM 18

19 Techical Data Series T6H29C, Deiso Hybrid Pump Power loss Ps [kw] Iteral leakage qs [l/mi] INTERNAL LEAKAGE (TYPICAL) P2 CARTRIDGE Do ot operate pump more tha 5 secods at ay speed or viscosity if iteral leakage is higher tha 50% of theoretical flow. HYDROMECHANICAL POWER LOSS (TYPICAL) P2 CARTRIDGE = 2400 RPM = 1500 RPM [24 cst] Lp. Noise level [db(a)] 1m ISO 4412 Flow [l/mi] NOISE LEVEL (TYPICAL) T6H29C - B22 Pe = 0,9 bar abs = 1500 RPM Lw = Lp + 8 db (A) Noise level is give with each cartridge dischargig at the pressure oted o the curve (P1 full flow). ν OUTLET FLOW P1 CARTRIDGE = 1000 RPM = 1500 RPM = 1800 RPM = 2400 RPM = 24 cst OVERALL EFFICIENCY - P1 CARTRIDGE Full displacemet INPUT HORSEPOWER - P1 CARTRIDGE Full displacemet Efficiecy [%] = 1500 RPM = 1800 RPM = 2400RPM Horse power [kw] = 1500 RPM = 1800 RPM = 2400 RPM 19

20 Orderig Code ad Characteristics Series T6H29D, Deiso Hybrid Pump Model No. T6H29D L 1 B - 2 F 0 M Series ad capacity P1 (rotatig group) 61,9 ml/rev. Cam rig P2 (Delivery at 0 bar & 1500 r.p.m.) 014 = 71,4 l/mi 017 = 87,3 l/mi 020 = 99,0 l/mi 024 = 119,3 l/mi 028 = 134,5 l/mi 031 = 147,4 l/mi 035 = 166,5 l/mi 038 = 180,4 l/mi 042 = 204,0 l/mi 045 = 218,5 l/mi 050 = 237,0 l/mi Type of shaft 1 = keyed (SAE C) 4 = splied (SAE C) Direct. of rotatio (view o shaft ed) R = clockwise L = couter-clockwise Seal class 1 = S1 BUNA N 5 = S5 VITON Desig letter Modificatio Portig combiatio Deped o the rotatio - See page 26 Variables port Dia Code P2 1"1/4 0 Variables flages coectios 4 bolts SAE flage (J518c) 0 = UNC thread M = metric thread) Cotrol accessories 0 = Maxi flow 9 = 90% maxi flow 8 = 80% maxi flow 7 = 70% maxi flow 6 = 60% maxi flow 5 = 50% maxi flow Cotrol C = Compesator F = RC pilot operated compesator L = RC pilot operated compesator load sesig Coectio (drai + vet.) 0 = ext. drai + UNF thread 2 = ext. drai + BSPP thread 3 = it. drai + UNF thread 4 = it. drai + BSPP thread OPERATING CHARACTERISTICS - TYPICAL [24 cst] Pressure port P2 T6H29D Series Volumetric Displacemet Vi Flow Q [l/mi], = 1500 RPM Iput power P [kw], = 1500 RPM p = 0 bar p = 140 bar p = 240 bar p = 7 bar p = 140 bar p = 240 bar ,6 ml/rev 71,4 62,1 55,9 2,3 18,5 30, ,2 ml/rev 87,3 78,0 71,8 2,5 22,2 37, ,0 ml/rev 99,0 89,7 83,5 2,8 24,9 41, ,5 ml/rev 119,3 110,0 103,8 3,0 29,6 49, ,7 ml/rev 134,5 125,2 119,0 3,2 33,2 55, ,3 ml/rev 147,4 138,1 131,9 3,3 36,2 61, ,0 ml/rev 166,5 157,2 151,0 3,5 40,7 68, ,3 ml/rev 180,4 171,1 164,9 3,7 43,9 74, ) 136,0 ml/rev 204,0 194,7 188,5 4,0 49,4 83, ) 145,7 ml/rev 218,5 209,2 203,0 4,1 52,8 89, ) 158,0 ml/rev 237,0 227,7 224,0 2) 4,4 57,0 85,0 2) 1) = max RPM 2) 050 = 210 bar max. it. 20

21 Dimesios - Weight : 60,0 kg Series T6H29D, Deiso Hybrid Pump VP VENT PORT 1/4 BSPP OR SAE-4 CONTROL F OR L DR DRAIN PORT 1/2 BSPP OR SAE-8 (PLUGGED FOR INTERNAL DRAIN) TYPE F TYPE L (M12 x 24 DEEP-METRIC VERSION) 7/16-14 UNC x 24 DEEP MOUNTING TORQUE 190 Nm (M16 x 25 DEEP-METRIC VERSION) 5/8-11 UNC x 25 DEEP P1 Ø 31,8 for CCW ROT S Ø 63,5 for CW ROT (M12 x 24 DEEP-METRIC VERSION) 7/16-14 UNC x 24 DEEP SIDE OF CONTROLS FOR CCW ROTATION Shaft code 3 INVOLUTE SPLINE SAE C FLAT ROOT - SIDE FIT J498b-CLASS, 1-PITCH, 12/24 14 TEETH - PRESS. ANGLE: 30 KEY 7,94 7,89 M10 x 20 DEEP 35,27 MAX INTERNAL ALTERNATE DRAIN HYDRAULIC CIRCUIT EXTERNAL (PREFERED) (SHOWED FOR F OR L CONTROL) MOUNTING TORQUE 180 Nm P1 Ø 31,8 for CW ROT S Ø 63,5 for CCW ROT MOUNTING TORQUE 41 Nm SIDE OF CONTROLS FOR CW ROTATION Shaft code 1 KEYED SAE C Shaft torque limits [ml/rev. x bar] Shaft Vi x p max

22 Techical Data Series T6H29D, Deiso Hybrid Pump Power loss Ps [kw] Iteral leakage qs [l/mi] INTERNAL LEAKAGE (TYPICAL) P2 CARTRIDGE Do ot operate pump more tha 5 secods at ay speed or viscosity if iteral leakage is higher tha 50% of theoretical flow. HYDROMECHANICAL POWER LOSS (TYPICAL) P2 CARTRIDGE = 2400 RPM = 1500 RPM [24 cst] Lp. Noise level [db(a)] 1m ISO 4412 Flow [l/mi] NOISE LEVEL (TYPICAL) T6H29D Pe = 0,9 bar abs = 1500 RPM Lw = Lp + 8 db (A) Noise level is give with each cartridge dischargig at the pressure oted o the curve (P1 full flow). ν OUTLET FLOW P1 CARTRIDGE = 1000 RPM = 1500 RPM = 1800 RPM = 2400 RPM = 24 cst OVERALL EFFICIENCY - P1 CARTRIDGE Full displacemet INPUT HORSEPOWER - P1 CARTRIDGE Full displacemet Efficiecy [%] = 1500 RPM = 1800 RPM = 2400RPM Horse power [kw] = 1500 RPM = 1800 RPM = 2400 RPM 22

23 Orderig Code ad Characteristics Series T6H29DB, Deiso Hybrid Pump Model No. T6H29DB B10-1 L 1 B - 2 F 0 M Series ad capacity P1 (rotatig group) 61,9 ml/rev. Cam rig P2 (Delivery at 0 bar & 1500 r.p.m.) 014 = 71,4 l/mi 017 = 87,3 l/mi 020 = 99,0 l/mi 024 = 119,3 l/mi 028 = 134,5 l/mi 031 = 147,4 l/mi 035 = 166,5 l/mi 038 = 180,4 l/mi 042 = 204,0 l/mi 045 = 218,5 l/mi 050 = 237,0 l/mi Cam rig P3 (Delivery at 0 bar & 1500 r.p.m.) B02 = 8,7 l/mi B03 = 14,7 l/mi B04 = 19,2 l/mi B05 = 23,9 l/mi B06 = 29,7 l/mi B07 = 33,7 l/mi B08= 37,4 l/mi B10 = 47,7 l/mi B12 = 61,5 l/mi B15 = 75,0 l/mi Type of shaft 1 = keyed (SAE C) 3 = splied (SAE C) Direct. of rotatio (view o shaft ed) R = clockwise L = couter-clockwise Seal class 1 = S1 BUNA N 5 = S5 VITON OPERATING CHARACTERISTICS - TYPICAL [24 cst] Pressure port P2 P3 Series Volumetric Displacemet Vi Flow Q [l/mi], = 1500 RPM Iput power P [kw], = 1500 RPM p = 0 bar p = 140 bar p = 240 bar p = 7 bar p = 140 bar p = 240 bar ,6 ml/rev 71,4 62,1 55,9 2,3 18,5 30, ,2 ml/rev 87,3 78,0 71,8 2,5 22,2 37, ,0 ml/rev 99,0 89,7 83,5 2,8 24,9 41, ,5 ml/rev 119,3 110,0 103,8 3,0 29,6 49, ,7 ml/rev 134,5 125,2 119,0 3,2 33,2 55, ,3 ml/rev 147,4 138,1 131,9 3,3 36,2 61, ,0 ml/rev 166,5 157,2 151,0 3,5 40,7 68, ,3 ml/rev 180,4 171,1 164,9 3,7 43,9 74, ) 136,0 ml/rev 204,0 194,7 188,5 4,0 49,4 83, ) 145,7 ml/rev 218,5 209,2 203,0 4,1 52,8 89, ) 158,0 ml/rev 237,0 227,7 224,0 2) 4,4 57,0 85,0 2) p = 0 bar p = 140 bar p = 300 bar p = 7 bar p = 140 bar p = 300 bar B02 5,8 ml/rev 8,7 7,0 5,1 0,5 2,6 5,1 B03 17,2 ml/rev 14,7 13,0 11,1 0,6 4,0 8,1 B04 21,3 ml/rev 19,2 17,5 15,6 0,6 5,0 10,4 B05 26,4 ml/rev 23,9 22,2 20,2 0,7 6,1 12,7 B06 34,1 ml/rev 29,7 28,0 26,1 0,7 7,5 15,6 B07 37,1 ml/rev 33,7 32,0 30,2 0,8 8,5 17,6 B08 46,0 ml/rev 37,4 35,7 33,7 0,8 9,3 19,5 B10 58,3 ml/rev 47,7 46,0 44,1 0,9 11,7 24,6 B12 63,8 ml/rev 61,5 59,8 57,9 1,2 14,9 31,5 B15 70,3 ml/rev 75,0 73,3 71,6 3) 1,3 18,1 35,7 3) 1) = max RPM 2) 050 = 210 bar max. it. 3) B15 = 280 bar max. it Modificatio Portig combiatio Deped o the rotatio - See page 27 Variable port Dia Code P2 1" 0 P3 3/4" 1 Variables flages coectios 4 bolts SAE flage (J518c) 0 = UNC thread M = metric thread) Cotrol accessories 0 = Maxi flow 9 = 90% maxi flow 8 = 80% maxi flow 7 = 70% maxi flow 6 = 60% maxi flow 5 = 50% maxi flow Cotrol C = Compesator F = RC pilot operated compesator L = RC pilot operated compesator load sesig Coectio (drai + vet.) 0 = ext. drai + UNF thread 2 = ext. drai + BSPP thread 3 = it. drai + UNF thread 4 = it. drai + BSPP thread Desig letter 23

24 Dimesios - Weight : 72,0 kg Series T6H29DB, Deiso Hybrid Pump VP VENT PORT 1/4 BSPP OR SAE-4 CONTROL F OR L DR DRAIN PORT 1/2 BSPP OR SAE-8 (PLUGGED FOR INTERNAL DRAIN) TYPE: F & L TYPE: C TYPE F TYPE L (M10 x 19 DEEP-METRIC VERSION) 3/8-16 UNC x 19 DEEP (M12 x 24 DEEP-METRIC VERSION) 7/16-14 UNC x 24 DEEP (M16 x 25 DEEP-METRIC VERSION) 5/8-11 UNC x 25 DEEP (M12 x 24 DEEP-METRIC VERSION) 7/16-14 UNC x 24 DEEP P1 Ø 31,8 for CCW ROT MOUNTING TORQUE 80 Nm MOUNTING TORQUE 190 Nm S Ø 76 for CW ROT SIDE OF CONTROLS FOR CCW ROTATION Shaft code 3 INVOLUTE SPLINE SAE C FLAT ROOT - SIDE FIT J498b-CLASS, 1-PITCH, 12/24 14 TEETH - PRESS. ANGLE: 30 KEY 7,94 7,89 M10 x 20 DEEP 35,27 MAX INTERNAL EXTERNAL(PREFERED) Shaft code 1 KEYED SAE C ALTERNATE DRAIN HYDRAULIC CIRCUIT (SHOWED FOR "F" "L" OR "X" CONTROL) Shaft torque limits [ml/rev. x bar] Shaft Vi x p max. (P1+P2+P3) MOUNTING TORQUE 180 Nm P1 Ø 31,8 for CW ROT S Ø 76 for CCW ROT SIDE OF CONTROLS FOR CW ROTATION Variable port Port Code A B Ø C P2 0 52,4 26,2 25,4 P2 1 47,7 22,4 19,0 MOUNTING TORQUE 41 Nm 24

25 Techical Data Series T6H29DB, Deiso Hybrid Pump Power loss Ps [kw] Iteral leakage qs [l/mi] INTERNAL LEAKAGE (TYPICAL) P2 - P3 CARTRIDGES Do ot operate pump more tha 5 secods at ay speed or viscosity if iteral leakage is higher tha 50% of theoretical flow. HYDROMECHANICAL POWER LOSS (TYPICAL) P2 - P3 CARTRIDGES = 2400 RPM = 1500 RPM [24 cst] = 2400 RPM = 1500 RPM [24 cst] Lp. Noise level [db(a)] 1m ISO 4412 Flow [l/mi] NOISE LEVEL (TYPICAL) T6H29DB B10 Pe = 0,9 bar abs = 1500 RPM Lw = Lp + 8 db (A) Noise level is give with each cartridge dischargig at the pressure oted o the curve (P1 full flow). ν OUTLET FLOW P1 CARTRIDGE = 1000 RPM = 1500 RPM = 1800 RPM = 2400 RPM = 24 cst OVERALL EFFICIENCY - P1 CARTRIDGE Full displacemet INPUT HORSEPOWER - P1 CARTRIDGE Full displacemet Efficiecy [%] = 1500 RPM = 1800 RPM = 2400RPM Horse power [kw] = 1500 RPM = 1800 RPM = 2400 RPM 25

26 Portig Diagrams Series T6H, Deiso Hybrid Pump DEPEND ON THE ROTATION T6H20B - T6H20C T6H29B - T6H29C CCW ROTATION FIXED PORTS CW ROTATION FIXED PORTS T6H29D FIXED PORTS FIXED PORTS CCW ROTATION CW ROTATION 26

27 Portig Diagrams Series T6H, Deiso Hybrid Pump DEPEND ON THE ROTATION T6H29DB FIXED PORTS FIXED PORTS CCW ROTATION CW ROTATION 27

28 Parker Worldwide AE UAE, Dubai Tel: parker.me@parker.com AR Argetia, Bueos Aires Tel: AT Austria, Wieer Neustadt Tel: +43 (0) parker.austria@parker.com AT Easter Europe, Wieer Neustadt Tel: +43 (0) parker.easteurope@parker.com AU Australia, Castle Hill Tel: +61 (0) AZ Azerbaija, Baku Tel: parker.azerbaija@parker.com BE/LU Belgium, Nivelles Tel: +32 (0) parker.belgium@parker.com BR Brazil, Cachoeiriha RS Tel: BY Belarus, Misk Tel: parker.belarus@parker.com CA Caada, Milto, Otario Tel: CH Switzerlad, Etoy Tel: +41 (0) parker.switzerlad@parker.com CL Chile, Satiago Tel: CN Chia, Shaghai Tel: CZ Czech Republic, Klecay Tel: parker.czechrepublic@parker.com DE Germay, Kaarst Tel: +49 (0) parker.germay@parker.com DK Demark, Ballerup Tel: parker.demark@parker.com ES Spai, Madrid Tel: parker.spai@parker.com FI Filad, Vataa Tel: +358 (0) parker.filad@parker.com FR Frace, Cotamie s/arve Tel: +33 (0) parker.frace@parker.com GR Greece, Athes Tel: parker.greece@parker.com HK Hog Kog Tel: HU Hugary, Budapest Tel: parker.hugary@parker.com IE Irelad, Dubli Tel: +353 (0) parker.irelad@parker.com IN Idia, Mumbai Tel: IT Italy, Corsico (MI) Tel: parker.italy@parker.com JP Japa, Fujisawa Tel: +(81) KR South Korea, Seoul Tel: KZ Kazakhsta, Almaty Tel: parker.easteurope@parker.com LV Latvia, Riga Tel: parker.latvia@parker.com MX Mexico, Apodaca Tel: MY Malaysia, Shah Alam Tel: NL The Netherlads, Oldezaal Tel: +31 (0) parker.l@parker.com NO Norway, Ski Tel: parker.orway@parker.com NZ New Zealad, Mt Welligto Tel: PL Polad, Warsaw Tel: +48 (0) parker.polad@parker.com PT Portugal, Leca da Palmeira Tel: parker.portugal@parker.com RO Romaia, Bucharest Tel: parker.romaia@parker.com RU Russia, Moscow Tel: parker.russia@parker.com SE Swede, Spåga Tel: +46 (0) parker.swede@parker.com SG Sigapore Tel: SK Slovakia, Baská Bystrica Tel: parker.slovakia@parker.com SL Sloveia, Novo Mesto Tel: parker.sloveia@parker.com TH Thailad, Bagkok Tel: TR Turkey, Istabul Tel: parker.turkey@parker.com TW Taiwa, Taipei Tel: UA Ukraie, Kiev Tel parker.ukraie@parker.com UK Uited Kigdom, Warwick Tel: +44 (0) parker.uk@parker.com US USA, Clevelad (idustrial) Tel: US USA, Licolshire (mobile) Tel: VE Veezuela, Caracas Tel: ZA South Africa, Kempto Park Tel: +27 (0) parker.southafrica@parker.com Europea Product Iformatio Cetre Free phoe: (from AT, BE, CH, CZ, DE, DK, EE, ES, FI, FR, IE, IL, IS, IT, LU, MT, NL, NO, PL, PT, RU, SE, UK, ZA) HYGE Ed Parker Haifi Corporatio. All rights reserved. Catalogue HY /UK. XM 07/2009 PC Parker Haifi Ltd. Tachbrook Park Drive Tachbrook Park, Warwick CV34 6TU Uited Kigdom Tel.: +44 (0) Fax: +44 (0) Your local authorized Parker distributor