Wireless Bluetooth Barcode Scanner. Instruction Manual

Transcription

1 Wireless Bluetooth Barcode Scanner Instruction Manual

2 Features * Design for kinds of bluetooth in PC; * Bar Codes Storable under the condition of no signal; * 5,000 bar codes storage available under off-line; * Common mode, Inventory Mode, ****Available, Free interchange; * Support computer of Windows XP, Win 7, Win8 system, Android & ISO Device. Packing List: BW3,USB Cable, Instruction Manual; Diagram * Lots of kinds of bar codes decoding available; * Shockproof & Crashproof design; * Independent intellectual property; * Operation smoothly; * Long time Service life : 3 millions times * Bluetooth standard available without adapter; * 80 meters long distance scanning; Customized Bar Codes, Customized Setting.

3 PERFORMANCE PARAMETERS Bluetooth Module Bluetooth 3.0 Module Light Source Wavelength: 650±8nm red laser Decode Capability Scanning Accurate Depth of Field Scan Width Scan Pattern Symbol Contrast Scanning Angle Warning Tone EAN-8, EAN-13, UPC-A, UPC-E, Code 39, Code 93, Code 128, EAN 128, Codabar, Code 25 non-interleaved, Code 25 interleaved, Matrix 2 of 5, MSI, PostBar, etc 0.102(4mil) 25mm-350mm 18CM Both way Single line 20% minimum reflectance difference Rotate Angle: 1±30 Tilt Angle: 2±45 skewing Angle:3±60 Beep and Indicator Transmission Distance 10-80M Eeprom Battery 512KB, 5000 bar codes storage Available 1000MA Bluetooth Match Windows XP 1. Turn on scanner, Hold trigger 8 seconds or Scanning setting codes Match Mode, Indicator (Blue) will flash 2. Find out bluetooth in the control panel, turn on bluetooth panel, Click add ; 3. Selected my device has finished, Search available, Click Next ; 4. A wizard dialog box about add bluetooth setting will display, Click symbol general bluetooth HID barcode Iron, Ignore the display dialog box, Click Next, Driver will be start installation; 5. One more device symbol HID bar code scanner on the device after bluetooth installation successfully. in the meanwhile, one beep showing means scanner and computer has match successfully, indicator will light all the time. Window7 1.Turn on scanner, Hold trigger 8 seconds or Scanning setting codes Match Mode, Indicator (Blue) will flash 2. Find out Device & Printer on control panel,click Add, A wizard dialog box about add bluetooth setting will display, Click symbol general bluetooth HID bar code Iron on the dialog box; 3. Right-click symbol general bluetooth HID bar code, Property of it will display, Mark it Keyboard, mouse and driver(hid) then click OK, Computer will reminder that driver is installation; 4. Indicator will light all the time after scanner and computer match successfully.

4 Window8 1.Turn on scanner, Hold trigger 8 seconds or Scanning setting codes Match Mode, Indicator (Blue) will flash 2.Turn on control panel, Select add device, Computer will search symbol general bluetooth HID bar code device; 3. Double-click or click Next, Computer will installation automatically; 4. Indicator will light all the time if finished installation successfully. In the meanwhile,one beep showing means scanner and computer has match successfully. Android,IOS 1.Turn on scanner, Hold trigger 8 seconds or Scanning setting codes Match Mode, Indicator (Blue) will flash 2. Turn on bluetooth on the device, search for symbol general bluetooth HID bar code ; 3. Click bluetooth device, then Match; 4. Scanner indicator will light all the time if match successfully. Indicator Green Light & Turn off rapidly Blue Light Flash Blue Light All The Time Red Light All The Time Red Light Flash Decoding successfully & One Beep Enter match pattern, Connecting Match Successfully & Two Beep Charging Power Poor Contact Beep Long beep 2 Seconds Wrong Default, Full Outer EEPROM Long beep 3 Times Power shortage, Voltage lower than 3.2V Short beep 20 times Wrong outer storage default & Outer EEPROM editor Short beep 1time Upload successfully Short beep 2 times Bluetooth Connect Successfully Short beep 3 times Wrong upload, Connect Failed Short beep 5 times Wrong Setting, Wrong Match Bar code Setting Match Mode Data Upload

5 Common Mode Data Amount Inventory Mode Data to Zero Storage Mode Turn off Volume Turn on Volume Power off Command Sleep Time - 10mins Sleep Time- 20mins

6 FAQ 1. Can t connect with Android phone? Confirm the version of phone up to Why some bar code can be decoding? Because some of the bar code are closed under default, Turn on the corresponding setting bar code; 3. Why not upload to the computer or mobile phone after match successfully? Confirm whether it has been match successfully, Indicator will light all the time after scanner and computer match successfully. 4. Computer or mobile phone can t search the bluetooth? a. Confirm the scanner has open the bluetooth mode; b. Confirm that scanner has match. Indicator light (blue) will flash 5. Scanner has been connected to the phone or computer, how to match the phone or computer again? a. Select the paired bluetooth scanner in the PC panel, click the "delete" button (or cancel the paired bluetooth device in your mobile phone ) b.scanner setting so that the Scanner into the pairing state (Two ways as following) a. Turn on Bluetooth scanner, Hold trigger 8 seconds or Scanning setting codes Match Mode, Indicator (Blue) will flash b. Scanning "Match Mode", Indicating light (blue) will flashing rapidly; 6. Re-plug the Bluetooth adapter or restart the phone, Bluetooth can not connect automatically? To ensure that the computer or mobile phone and other Bluetooth devices are not connected to the case, restart the scanner can be connected automatically.