ArmorPoint 24V dc Output Modules, Series A

Transcription

1 Installation Instructions ArmorPoint V dc Output Modules, Series A Catalog Numbers 8-OB8EM, 8-OB8EM, 8-OB8EM8, 8-OBEM, 8-OBEM8, 8-OBEM, 8-OBEPM, 8-OVEM The ArmorPoint I/O family consists of modular I/O modules. The sealed IP housing of these modules requires no enclosure. (Note that environmental requirements other than IP may require an additional appropriate housing.) I/O connectors are sealed M8 (pico) or M (micro) or M styles. The mounting base ships with the module. The 8-OB8EM, 8-OB8EM, and 8-OB8EM8 modules are shown below. 8-OB8EM M-A 8-OB8EM 8-OB8EM/A V dc In 8-OB8EM/A V dc Out M-B MOD NET LED Indicators MOD NET LED Indicators M-C M 8 8-OB8EM8 M-D 8-OB8EM8/A V dc.amp Out M8-A M8-C M8-E M8-G MOD NET M8-B M8-D LED Indicators M8-F M8-G 8

2 ArmorPoint V dc Output Modules, Series A. Important User Information Solid state equipment has operational characteristics differing from those of electromechanical equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls (Publication SGI-. available from your local Rockwell Automation sales office or online at describes some important differences between solid state equipment and hard-wired electromechanical devices. Because of this difference, and also because of the wide variety of uses for solid state equipment, all persons responsible for applying this equipment must satisfy themselves that each intended application of this equipment is acceptable. In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages resulting from the use or application of this equipment. The examples and diagrams in this manual are included solely for illustrative purposes. Because of the many variables and requirements associated with any particular installation, Rockwell Automation, Inc. cannot assume responsibility or liability for actual use based on the examples and diagrams. No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits, equipment, or software described in this manual. Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell Automation, Inc. is prohibited. Throughout this manual we use notes to make you aware of safety considerations. Identifies information about practices or circumstances that can cause an explosion in a WARNING hazardous environment, which may lead to personal injury or death, property damage, or economic loss. IMPORTANT ATTENTION SHOCK HAZARD Identifies information that is critical for successful application and understanding of the product. Identifies information about practices or circumstances that can lead to personal injury or death, property damage, or economic loss. Attentions help you: identify a hazard avoid a hazard recognize the consequence Labels may be located on or inside the equipment to alert people that dangerous voltage may be present. BURN HAZARD Labels may be located on or inside the equipment to alert people that surfaces may be dangerous temperatures.

3 ArmorPoint V dc Output Modules, Series A ATTENTION Environment and Enclosure This equipment is intended for use in overvoltage Category II applications (as defined in IEC publication -), at altitudes up to meters without derating. This equipment is considered Group, Class A industrial equipment according to IEC/CISPR Publication. Without appropriate precautions, there may be potential difficulties ensuring electromagnetic compatibility in other environments due to conducted as well as radiated disturbance. This equipment is supplied as enclosed equipment. It should not require additional system enclosure when used in locations consistent with the enclosure type ratings stated in the Specifications section of this publication. Subsequent sections of this publication may contain additional information regarding specific enclosure type ratings, beyond what this product provides, that are required to comply with certain product safety certifications. NOTE: See NEMA Standards publication and IEC publication 9, as applicable, for explanations of the degrees of protection provided by different types of enclosure. Also, see the appropriate sections in this publication, as well as the Allen-Bradley publication -. (Industrial Automation Wiring and Grounding Guidelines), for additional installation requirements pertaining to this equipment.

4 ArmorPoint V dc Output Modules, Series A ATTENTION Preventing Electrostatic Discharge This equipment is sensitive to electrostatic discharge, which can cause internal damage and affect normal operation. Follow these guidelines when you handle this equipment: Touch a grounded object to discharge potential static. Wear an approved grounding wriststrap. Do not touch connectors or pins on component boards. Do not touch circuit components inside the equipment. If available, use a static-safe workstation. When not in use, store the equipment in appropriate static-safe packaging. Mount the I/O Base To mount the I/O base on a wall or panel, use the screw holes provided in the base. IMPORTANT The module must be mounted on a grounded metal mounting plate or other conductive surface. Refer to the Drilling Dimensions illustration of the base with an adapter to help you mount the base. Drilling dimensions Adapter.9 in.. mm. in. mm.8 in. mm. in. mm.8 in. mm. in. mm. in. mm.8 in. mm 9

5 ArmorPoint V dc Output Modules, Series A Install the mounting base as follows:. Lay out the required points as shown above in the drilling dimensions drawing.. Drill the necessary holes for #8 (M) machine or self-tapping screws.. Mount the base using #8 (M) screws.. Ground the system using the ground lug connection. The ground lug connection is also a mounting hole. Mounting base Keyswitch- Set to position for the 8 digital output modules Ground lug connection Latching mechanism

6 ArmorPoint V dc Output Modules, Series A Install the ArmorPoint Digital Output Module To install the ArmorPoint digital output module, proceed as follows.. Using a bladed screwdriver, rotate the keyswitch on the mounting base clockwise until the number aligns with the notch in the base.. Position the module vertically above the mounting base. The module bridges two bases. Module bridges two bases. 8-OB8EM/A V dc Out MOD NET. Push the module down until it engages the latching mechanism. You hear a clicking sound when the module is properly engaged. The locking mechanism locks the module to the base. Remove the Module From the Mounting Base To remove the module from the mounting base:. Put a flat blade screwdriver into the slot of the orange latching mechanism.. Push the screwdriver toward the I/O module to disengage the latch. The module lifts up off the base.. Pull the module off of the base.

7 ArmorPoint V dc Output Modules, Series A Wire the Modules Following are wiring instructions for the ArmorPoint digital output modules. 8-OBEM, 8-OBEPM, 8-OVEM, and 8-OBEM (view into connector) Pin - V dc Pin - No Connect Pin - Common Pin - Output (M-A) Output (M-B) Output (M-C) (8-OVEM and-obem only) Output (M-D) (8-OVEM and-obem only) Pin - No Connect 8-OBEM8 and 8-OB8EM8 8 (view into connector) Pin - V dc Pin - Common Pin - Output (M8-A) Output (M8-B) Output (M8-C) Output (M8-D) Output (M8-E) (8-OB8EM8 module only) Output (M8-F) (8-OB8EM8 module only) Output (M8-G) (8-OB8EM8 module only) Output (M8-H) (8-OB8EM8 module only) 8-OB8EM (view into connector) Pin - V dc Pin - Output (M-A) Pin - Output (M-A) Output (M-B) Output (M-B) Output (M-C) Output (M-C) Output (M-D) Output (M-D) Pin - Common Pin - No Connect

8 8 ArmorPoint V dc Output Modules, Series A 8-OB8EM (view into connector) Pin -Output Pin - Output Pin -Output Pin 8 - Output Pin -Output Pin 9 - Return (Com) Pin -Output Pin - Return (Com) Pin -Output Pin - V dc Pin -Output Pin - Chassis ATTENTION Make sure all connectors and caps are securely tightened to properly seal the connections against leaks and maintain IP requirements. Communicate with Your Module I/O messages are sent to (consumed) and received from (produced) the ArmorPoint I/O modules. Messages are mapped into the processor s memory. ArmorPoint I/O output modules produce byte of input data (scanner Rx - status). They consume byte of I/O data (scanner Tx). Default Data Map for the ArmorPoint Output Modules 8-OBEM and 8-OBEPM Message size: Byte Produces (scanner Rx) Consumes (scanner Tx) Not Used Ch Ch Channel status Not Used Ch Ch Output state Where: Channel status = no error, = error; Output state = off, = on

9 ArmorPoint V dc Output Modules, Series A 9 8-OBEM, 8-OBEM8, 8-OVEM Message size: Byte Produces (scanner Rx) Consumes (scanner Tx) 8-OB8EM, 8-OB8EM, 8-OB8EM8 Message size: Byte Not Used Ch Ch Ch Ch Channel status Not Used Ch Ch Ch Ch Output state Where: Channel status = no error, = error; Output state = off, = on Produces (scanner Rx) Consumes (scanner Tx) Ch Ch Ch Ch Ch Ch Ch Ch Channel status Ch Ch Ch Ch Ch Ch Ch Ch Output state Where: Channel status = no error, = error; Output state = off, = on

10 ArmorPoint V dc Output Modules, Series A Troubleshoot with the Indicators 8-OB8EM 8-OB8EM/A V dc Out MOD NET Module Status Indicator Network Status Indicator I/O Status Indicators Indication Module Status Off Green Flashing Green Flashing Red Red Flashing Red/Green Probable Cause No power applied to device Device operating normally Device needs commissioning due to missing, incomplete, or incorrect configuration Recoverable fault Unrecoverable fault - may require device replacement Device is in self-test Indication Network Status Off Flashing Green Green Flashing Red Red Flashing Red/Green Probable Cause Device is not on line: - Device has not completed dup_mac-id test. - Device not powered - check module status indicator. Device is on line but has no connections in the established state. Device is on line and has connections in the established state. One or more I/O connections in timed-out state. Critical link failure - failed communication device. Device detected error that prevents it from communicating on the network. Communication faulted device - the device has detected a network access error and is in communication faulted state. Device has received and accepted an Identity Communication Faulted Request - long protocol message.

11 ArmorPoint V dc Output Modules, Series A Indication I/O Status Off Yellow Flashing Red Red Probable Cause Output is inactive. Output is active and under control. Open circuit detection. No load. (Off-State only) Short circuit detected. (On-State only) Specifications ArmorPoint Digital Output Modules Number of Outputs Voltage Drop, On-state Output, Max. Voltage, External DC Power Supply, Range Voltage, External DC Power Supply, Nom. Voltage, Off-state Output, Max. Voltage, On-state Output, Nom. Voltage, On-state Output, Max Voltage, On-state Output, Min Voltage, Operating Current, External DC Power Supply Current Leakage, Off-state Output, Max. Current, On-state Output Max. Current, On-state Output Min. Current, Output Rating Current, Output Surge, Max. General Specifications Dimensions (includes I/O module Metric HxWxD and mounting base) Dimensions (includes I/O module Imperial.Hx.8Wx.D and mounting base) Isolation Voltage (continuous-voltage withstand rating) V rms Tested at V ac rms for s Keyswitch Position 8-OBE - ( group of ) non-isolated, sourcing 8-OBEP - ( group of ) non-isolated, sourcing 8-OBE - ( group of ) non-isolated, sourcing 8-OVE - ( group of ) non-isolated, sinking 8-OB8E - 8 ( group of 8) non-isolated, sourcing.v dc (sourcing modules).v dc (sinking module) 8.8V dc V dc 8.8V dc V dc 8.8V dc V dc 8.8V dc 8 ma ( connector module) ma ( connector modules) ma (8 connector modules). ma. A per channel, electronically protected. ma per channel 8-OBE -. A per channel, not to exceed. A maximum per module 8-OBEP -. A per channel,. A maximum per module 8-OBE and -OB8E -. A per channel, not to exceed. A maximum per module 8-OVE -. A per channel, not to exceed. A maximum per module A for ms, repeatable every seconds 8-OBEP - A, electronically protected

12 ArmorPoint V dc Output Modules, Series A General Specifications (cont) LED Indicators Output Delay Time, OFF to ON, Max. Output Delay Time, ON to OFF, Max.. ms Output Point Density,, 8 PointBus Current, Max. V dc Power Dissipation, Max.,, or 8 yellow/red output status, logic side green/red network status, logic side green/red module status, logic side. ms 8-OBE 8.8V dc 8-OBEP 8.8V dc 8-OBE 8.8V dc 8-OVE 8.8V dc 8-OB8E 8.8V dc Thermal Dissipation, Max. 8-OBE V dc 8-OBEP V dc 8-OBE V dc 8-OVE V dc 8-OB8E V dc Weight, Imperial. lb Weigh, Metric.9 kg Operating Temperature IEC 8-- (Test Ad, Operating Cold), IEC 8-- (Test Bd, Operating Dry Heat), IEC 8-- (Test Nb, Operating Thermal Shock): - C (- F) Storage Temperature IEC 8-- (Test Ab, Un-packaged Non-operating Cold), IEC 8-- (Test Bb, Un-packaged Non-operating Dry Heat), - 8 C (- 8 F) Relative Humidity IEC 8-- (Test Db, Un-packaged Non-operating Damp Heat): -9% non-condensing Shock IEC8-- (Test Ea, Unpackaged Shock): Operating g Non-operating g Vibration IEC8-- (Test Fc, Operating): - Hz ESD Immunity IEC --: kv contact discharges 8 kv air discharges Radiated RF Immunity IEC --: V/m with khz sine-wave 8% AM from MHz to MHz V/m with Hz % Pulse % AM at 9 Mhz V/m with Hz % Pulse % AM at 89 Mhz EFT/B Immunity IEC --: ± kv at khz on signal ports Surge Transient Immunity IEC --: ± kv line-line(dm) and ± kv line-earth(cm) on signal ports Conducted RF Immunity IEC --: Vrms with khz sine-wave 8% AM from khz 8 MHz Emissions CSPR : Group, Class A

13 ArmorPoint V dc Output Modules, Series A General Specifications (cont) Enclosure Type Rating Mounting Base Screw Torque Conductor Category Certifications: (when product is marked) Meets IP// (when marked) #8 screw,. in. lbs. in Aluminum, in. lbs. in Steel - on signal ports c-ul-us CE UL Listed Industrial Control Equipment, certified for US and Canada European Union 89//EEC EMC Directive, compliant with: EN --; Industrial Emissions EN 8-; Industrial Immunity EN ; Meas./Control/Lab., Industrial Requirements EN --; Industrial Immunity C-Tick Australian Radiocommunications Act, compliant with: AS/NZS CISPR ; Industrial Emissions. OFF to ON or ON to OFF delay is time from a valid output on or off signal to output energization or de-energization.. Use this Conductor Category information for planning conductor routing. Refer to Publication -., Industrial Automation Wiring and Grounding Guidelines.. See the Product Certification link at for Declarations of Conformity, Certificates, and other certification details.

14 Rockwell Automation Support Rockwell Automation provides technical information on the web to assist you in using our products. At you can find technical manuals, a knowledge base of FAQs, technical and application notes, sample code and links to software service packs, and a MySupport feature that you can customize to make the best use of these tools. For an additional level of technical phone support for installation, configuration and troubleshooting, we offer TechConnect Support programs. For more information, contact your local distributor or Rockwell Automation representative, or visit Installation Assistance If you experience a problem with a hardware module within the first hours of installation, please review the information that's contained in this manual. You can also contact a special Customer Support number for initial help in getting your module up and running: United States... Outside United States Monday Friday, 8am pm EST Please contact your local Rockwell Automation representative for any technical support issues. New Product Satisfaction Return Rockwell tests all of our products to ensure that they are fully operational when shipped from the manufacturing facility. However, if your product is not functioning and needs to be returned: United States Outside United States Contact your distributor. You must provide a Customer Support case number (see phone number above to obtain one) to your distributor in order to complete the return process. Please contact your local Rockwell Automation representative for return procedure. ArmorPoint is a trademark of Rockwell Automation. PN 99- Supersedes Publication 8-INB-EN-E - July Copyright Rockwell Automation, Inc. All rights reserved. Printed in the U.S.A.