PTVSHC3D5VU Transient Voltage Suppressor

Transcription

1 Transient Voltage Suppressor Description The ESD protector is designed to replace multilayer varistors (MLVs) in portable applications such as cell phones, notebook computers, and PDA s. They feature large cross-sectional area junctions for conducting high transient currents, offer desirable electrical characteristics for board level protection, such as fast response time, lower operating voltage, lower clamping voltage and no device degradation when compared to MLVs. The protects sensitive semiconductor components from damage or upset due to electrostatic discharge (ESD) and other voltage induced transient events. The is available in a SOD-323 package with working voltages of 5 volt. It is used to meet the ESD immunity requirements of IEC , (±3kV air, ±3kV contact discharge) Feature Applications 14W Peak pulse power per line (t P = 8/2μs) Cell phone handsets and accessories SOD-323 package Personal digital assistants (PDA s) Response time is typically < 1 ns Notebooks, desktops, and servers Protect one I/O or power line Portable instrumentation Low clamping Voltage Cordless phones RoHS compliant Digital cameras Transient protection for data lines to IEC (ESD) Peripherals ±3KV(air), ±3KV(contact); IEC (EFT) 4A (5/5ns) MP3 players Mechanical Characteristics Lead finish:1% matte Sn(Tin) Mounting position: Any Qualified max reflow temperature:26 Pure tin plating: 7 ~ 17 um Pin flatness: 3mil Rev

2 Electronics Parameter Symbol V RWM Parameter Peak Reverse Working Voltage I F I I R Reverse Leakage V RWM V BR Breakdown I T I T I PP V C Test Current Maximum Reverse Peak Pulse Current Clamping I PP V C V BR V RWM I R V F I T V P PP Peak Pulse Power C J Junction Capacitance I F Forward Current I PP V F Forward I F Electrical characteristics per line@25 ( unless otherwise specified) Parameter Symbol Conditions Min. Typ. Max. Units Peak Reverse Working Voltage V RWM 5 V Breakdown Voltage V BR I t =1mA V Reverse Leakage Current I R V RWM =5V 1 μa Clamping Voltage V C I PP=4A t P = 8/2μs V Clamping Voltage V C I PP=1A t P = 8/2μs V Junction Capacitance C j V R=V f = 1MHz pf Absolute maximum rating@25 Rating Symbol Value Units Peak Pulse Power ( t P = 8/2μS ) P pp 14 W Lead Soldering Temperature T L 26 (1 sec) Operating Temperature T J -55 to +15 Storage Temperature T STG -55 to +15 Rev

3 Peak Pulse Power (W) VC-Clamping Voltage (V) C-Junction capacitance (pf) % Of Rated Power Typical Characteristics IPP Peak Pulse Current - % of IPP t f=8μs t - Time -μs t P =2μs(I PP /2) T L Lead Temperature - Fig 1.Pulse Waveform Fig 2.Power Derating Curve 16 Pulse waveform: tp=8/2us 12 1 f=1mhz I PP-Peak pulse current (A) Fig 3. Clamping voltage vs. Peak pulse current V R-Reverse voltage (V) Fig 4. Capacitance vs. Reveres voltage Pulse Duration(us) Fig 5. Non Repetitive Peak Pulse Power vs. Pulse time Rev

4 Solder Reflow Recommendation 28 Peak Temp=257, Ramp Rate=.82deg. /sec Time (sec) PCB Design For TVS diodes a low-ohmic and low-inductive path to chassis earth is absolutely mandatory in order to achieve good ESD protection. Novices in the area of ESD protection should take following suggestions to heart: Do not use stubs, but place the cathode of the TVS diode directly on the signal trace. Do not make false economies and save copper for the ground connection. Place via holes to ground as close as possible to the anode of the TVS diode. Use as many via holes as possible for the ground connection. Keep the length of via holes in mind! The longer the more inductance they will have. Rev

5 Product dimension (SOD-323) E C A B Inches Millimeters Dim MIN MAX MIN MAX A B C D F D E F H H Unit:mm Ordering information Device Package Shipping SOD-323 (Pb-Free) 3 / Tape & Reel Rev

6 IMPORTANT NOTICE and are registered trademarks of Prisemi Electronics Co., Ltd (Prisemi),Prisemi reserves the right to make changes without further notice to any products herein. Prisemi makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Prisemi assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Typical parameters which may be provided in Prisemi data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including Typicals must be validated for each customer application by customer s technical experts. Prisemi does not convey any license under its patent rights nor the rights of others. The products listed in this document are designed to be used with ordinary electronic equipment or devices, Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. Website: For additional information, please contact your local Sales Representative. Copyright 29, Prisemi Electronics is a registered trademark of Prisemi Electronics. All rights are reserved. Rev