Product Certificate. DORMA-Glas GmbH herewith confirms that the product

Transcription

1 herewith confirms VISUR double-action door system has successfully completed a durability test aligned to EN This was conducted on the basis of a representative test series in which the fittings were applied to an all-glass door weighing 85 kg. Dimensions of the door leaf (width x height) 1100 mm x 2500 mm, toughened safety glass The door satisfied the requirement specified in EN 1154 of successfully completing 500,000 operating cycles. Further, pendulum impact tests were also carried out using a 40 kg pendulum. Test 1: Point of impact in the area of the rotating axis, 900mm above the floor surface. Pendulum drop height 305 mm. Test 2: Point of impact in the area of the primary closing edge, 900mm above the floor surface, during door closure in the opposite direction. Pendulum drop height 305 mm. The door satisfied the requirement: Functionally intact after pendulum impact test. Bad Salzuflen, 21 June, 2007 Head of Mechanical Design Germany

2 BEYOND Pivoting have been tested in an endurance test according to European EN 1154 standard. This took place in a series of exemplary tests; the fittings were mounted to a glass-door with 80 kg weight. Door width: 1000mm, door height: 2200mm. The corner patch fitting fulfils the demand given by the German DIN standard: operations (cycles) Bad Salzuflen,

3 Swing Door System MANET has been tested in an durability test according to DIN EN The fittings were mounted to an exemplarily glass door of 80, 100, 120kg (plus safety multiplier) weight. Please use a door closer type EN4 (with or without back check) or a higher type (e.g. EN5) WITHOUT back check. This certificate applies to the following conditions/limits: Variant Without continuous pivot bar With continuous pivot bar and 4 single point fixings With continuous pivot bar and 5 single point fixings Panel Weight Glass Thickness Door Width Door High 80kg >/=10mm </=2500mm 100kg >/=10mm </=1200mm </=2600mm 120kg >/=12mm </=3000mm Using in Variant V2A Variant V4A environments without influences of chloride and sulphur dioxide environments with moderate influences of chloride and sulphur dioxide able not able able able swimming and/or saline baths not able on enquiry For additional technical information s please check the actual technical prospect for DORMA-Glas. Bad Salzuflen, 18/12/2008 Division Glas Head of Mechanical Design and Development

4 Junior Office Band Hinges for/with frame pivots has been tested according to the EN1527. The product meets the following standards: Maximum door weight: Count of operations: 60kg (24mm rebate depth with sleeve and steel ball bearing) 55kg (24mm rebate depth with sleeve) 45kg (rebate depth >24mm up to 40mm) class 7 ( cycles) Corrosion resistance: class 3 Glass type: TSG Glass thickness [mm]: 8, 10 Glass surface: clear, calendered, no using of self-cleaning surfaces (Lotus, Clear-Shield etc.) Classification key EN1935: Bad Salzuflen, 21/04/2008 Division Glas Head of Mechanical Design and Development

5 Junior Office hinge with steel ball bearing Art.-Nr was tested according to the EN1935:2002 regarding durability and according to the EN1670:2007 regarding corrosion resistance with the following results: Maximum door weight: Durability: Corrosion resistance: 60kg Level 7, EN1935: operations Level 3, EN1670:2007 Bad Salzuflen, Division Glas Head of Mechanical Design and Development

6 Junior lock have been tested according to german DIN standard. This took place in an endurance test. The locking bolt fullfills the demand operations The ledge fullfills the demand operations Bad Salzuflen,

7 Studio lock have been tested according to german DIN standard. This took place in an endurance test. The locking bolt fullfills the demand operations The ledge fullfills the demand operations Bad Salzuflen,

8 Door rail with BTS-insert Art.-No Top patch Art.-No has been tested in an endurance test acording to EN This took place in a series of exemplary tests; the fittings were mounted to a glassdoor with 100 kg weight. Door width: 1100mm, Door height: 2000mm. The complete door fulfils the demand operations (cycles) Bad Salzuflen,

9 ARCOS Top Patch Fitting Art.-No ARCOS Bottom Patch Fitting Art.-No have been tested in an endurance test according to European EN 1154 standard. This took place in a series of exemplary tests; the fittings were mounted to a glass-door with 100 kg weight. Door width: 1000mm, door height: 2200mm the corner patch fitting fulfils the demand given by the German DIN standard: operations Bad Salzuflen,

10 Top Patch Fitting Art.-No Bottom Patch Fitting Art.-No has been tested in an durability test according to DIN EN The fittings were mounted to an exemplarily glass door of 130 kg (plus safety multiplier) weight. This certificate applies to the following conditions/limits: count of operations: </= door width </= 1.300mm door height </= 2.500mm For doors with more than 100kg weight please use a door closer type EN4 (with or without back check) or a higher type (e.g. EN5) WITHOUT back check. For doors with a height of more than 2.500mm additional the following conditions/limits has to be observed: glass thickness >/= 10mm Usage of a handle bar with 3 connection points in minimum and a minimum height of 2/3 door height. Bad Salzuflen, 1/25/2008

11 Overpanel Patch Fitting Art.-No has been tested in an endurance test according to EN 1154 a glassdoor of 101 kg weight was fitted with PT10/PT 20, attached to 2 x PT 30 with wall bracket Art.-No on wall. Overpanel fixed to ceiling with wall connecting profile Art.-No The fittings fulfilled the demand operations Bad Salzuflen,

12 Overpanel and Sidepanel Patch Fitting Art.-No has been tested in an endurance test according to EN a glassdoor of 101 kg weight was fitted with PT10/PT 20, attached to a PT 40 on pirot side and a PT 30 on lock side. PT 30 fixed to wall with bracket Art.-No Overpanel fixed to ceiling with wall connection profile Art.-No The fittings fulfilled the demand operations Bad Salzuflen,

13 DORMA-SM Type Latest drawing revision 2005 has been tested in an durability test according to EN1154. The fittings were mounted to an exemplarily glass door of 80kg (safety multiplier not included) weight. This certificate applies to the following conditions/limits: count of operations: </= door width </= 1.100mm door height </= 2.300mm door weight </= 80kg After operations all installed parts have to be checked according the following items: mechanical fractures screw torques precise position of the fittings Please use a door closer type EN4 only. Further technical information are given in technical documentation. Bad Salzuflen, 16/01/2009 Head of Mechanical Design and Development