3. ASME B16.9 Fittings
|
|
|
- Letitia Jackson
- 7 years ago
- Views:
Transcription
1 3. SME 16.9 Fittings
2 Section 3. SME 16.9 Fittings SME 16.9 uttwelding Fittings are designed and manufactured in accordance with the following specifications:- SME 16.9 MSS-SP-43 MSS-SP-75 NSI 31.3 SME VIII PI 6 NCE MR Factory-Made Wrought Steel uttwelding Fittings. Wrought Stainless Steel utt Weld Fittings. Specification for High Test Wrought utt Weld Fittings. Chemical Plant and Petroleum Refinery Piping. oiler and Pressure Vessel Code. Specification for Wellhead and Christmas Tree Equipment. Sulphide Stress Cracking Resistant Metallic Materials for Oilfield Equipment. uttwelding Fittings are available in either equal or with reducing configuration to suit various pressure ratings using materials as shown in the table below. PROPERTY F51 ISI 4130 Gr WP Gr WPL6 Gr 316L Gr WPHY52 UNS TENSILE 60,000 PSI 60,000 PSI 70,000 PSI 66,000 PSI 90,000 PSI 105,000 PSI STRENGTH 415 MPa 415 MPa 485 MPa 455 MPa 620 MPa 725 MPa YIEL 35,000 PSI 35,000 PSI 25,000 PSI 52,000 PSI 65,000 PSI >80,000 PSI STRENGTH 240 MPa 240 MPa 170 MPa 360 MPa 450 MPa >551 MPa IMPCT VLUES N/ 18J min.av. N/ 27J min.av. 27J min.av. 42J min.av. EG C -45 C -50 C -50 C -50 C HRNESS 197 H N/ N/ 235 H 237H 237H (MX.) ELONGTION Long. 30% Long. 30% 30% 32% 25% 18% In 2 or 50mm Trans. 20% Trans. 16.5% GENERL NOTE: Please contact RV Energy for any special material or dimensional requirements. 3.1
3 Section 3. SME 16.9 Fittings GENERL NOTE: imensions are in mm 3.2 Outside iameter at evel Table 3.1 imensions of Long Radius Elbows 90 deg. Elbows Centre-to-End 45 deg. Elbows Min. Nom. Max. ½ ¾ ¼ ½ ½ ½
4 Outside iameter at evel Table 3.1 imensions of Long Radius Elbows 90 deg. Elbows Centre-to-End 45 deg. Elbows Min. Nom. Max GENERL NOTE: imensions are in mm 3.3
5 Section 3. SME 16.9 Fittings Table 3.2 imensions of Long Radius Returns Outside iameter at evel Centre-to-Centre ack-to-face Min. Nom. Max. ½ ¾ ¼ ½ ½ ½ GENERL NOTE: imensions are in mm 3.4
6 Table 3.2 imensions of Long Radius Returns Outside iameter at evel Centre-to-Centre ack-to-face Min. Nom. Max GENERL NOTES: imensions are in mm imension R is equal to half of dimension. 3.5
7 Section 3. SME 16.9 Fittings GENERL NOTE: imensions are in mm 3.6 Outside iameter at evel Table 3.3 imensions of Straight Tees and Crosses Centre-to-End Min. Nom. Max. ½ ¾ ¼ ½ ½ ½
8 Outside iameter at evel Table 3.3 imensions of Straight Tees and Crosses Centre-to-End Min. Nom. Max GENERL NOTE: imensions are in mm 3.7
9 Section 3. SME 16.9 Fittings Table 3.4 imensions of Reducing Tees and Reducing Crosses Outside diameter of reducing Tees & Crosses ½ x ½ x ½ x ½ x ¼ ¾ x ¾ x ½ ¾ x ¾ x x 1 x ¾ x 1 x ½ ¼ x 1¼ x ¼ x 1¼ x ¾ ¼ x 1¼ x ½ ½ x 1½ x 1¼ ½ x 1½ x ½ x 1½ x ¾ ½ x 1½ x ½ x 2 x 1½ GENERL NOTE: imensions are in mm 3.8 Centre-end lengths Tees & Crosses
10 Table 3.4 imensions of Reducing Tees and Reducing Crosses Outside diameter of reducing Tees & Crosses 2 x 2 x 1¼ x 2 x x 2 x ¾ ½ x 2½ x ½ x 2½ x 1½ ½ x 2½ x 1¼ ½ x 2½ x x 3 x 2½ x 3 x x 3 x 1½ x 3 x 1¼ ½ x 3½ x ½ x 3½ x 2½ ½ x 3½ x ½ x 3½ x 1½ x 4 x 3½ x 4 x x 4 x 2½ x 4 x x 4 x 1½ x 5 x Centre-end lengths Tees & Crosses GENERL NOTE: imensions are in mm 3.9
11 Section 3. SME 16.9 Fittings Table 3.4 imensions of Reducing Tees and Reducing Crosses Outside diameter of reducing Tees & Crosses 5 x 5 x 3½ x 5 x x 5 x 2½ x 5 x x 6 x x 6 x x 6 x 3½ x 6 x x 6 x 2½ x 8 x x 8 x x 8 x x 8 x 3½ x 10 x GENERL NOTE: imensions are in mm 3.10 Centre-end lengths Tees & Crosses
12 Table 3.4 imensions of Reducing Tees and Reducing Crosses Outside diameter of reducing Tees & Crosses 10 x 10 x x 10 x x 10 x x 12 x x 12 x x 12 x x 12 x x 14 x x 14 x x 14 x x 14 x x 16 x x 16 x x 16 x x 16 x x 16 x x 18 x x 18 x x 18 x x 18 x x 18 x Centre-end lengths Tees & Crosses GENERL NOTE: imensions are in mm 3.11
13 Section 3. SME 16.9 Fittings Table 3.4 imensions of Reducing Tees and Reducing Crosses Outside diameter of reducing Tees & Crosses 20 x 20 x x 20 x x 20 x x 20 x x 20 x x 20 x x 22 x x 22 x x 22 x x 22 x x 22 x x 22 x x 24 x x 24 x GENERL NOTE: imensions are in mm 3.12 Centre-end lengths Tees & Crosses
14 Table 3.4 imensions of Reducing Tees and Reducing Crosses Outside diameter of reducing Tees & Crosses 24 x 24 x x 24 x x 24 x x 24 x x 24 x x 26 x x 26 x x 26 x x 26 x x 26 x x 26 x x 26 x x 28 x x 28 x x 28 x x 28 x x 28 x x 28 x x 28 x x 28 x x 30 x x 30 x Centre-end lengths Tees & Crosses GENERL NOTE: imensions are in mm 3.13
15 Section 3. SME 16.9 Fittings Table 3.4 imensions of Reducing Tees and Reducing Crosses Outside diameter of reducing Tees & Crosses 30 x 30 x x 30 x x 30 x x 30 x x 30 x x 30 x x 30 x x 30 x x 32 x x 32 x x 32 x x 32 x x 32 x x 32 x GENERL NOTE: imensions are in mm 3.14 Centre-end lengths Tees & Crosses
16 Table 3.4 imensions of Reducing Tees and Reducing Crosses Outside diameter of reducing Tees & Crosses 32 x 32 x x 32 x x 32 x x 34 x x 34 x x 34 x x 34 x x 34 x x 34 x x 34 x x 34 x x 34 x x 36 x x 36 x x 36 x x 36 x x 36 x x 36 x x 36 x x 36 x x 36 x x 36 x Centre-end lengths Tees & Crosses GENERL NOTE: imensions are in mm 3.15
17 Section 3. SME 16.9 Fittings Table 3.4 imensions of Reducing Tees and Reducing Crosses Outside diameter of reducing Tees & Crosses 38 x 38 x x 38 x x 38 x x 38 x x 38 x x 38 x x 38 x x 38 x x 38 x x 38 x x 40 x x 40 x x 40 x x 40 x GENERL NOTE: imensions are in mm 3.16 Centre-end lengths Tees & Crosses
18 Table 3.4 imensions of Reducing Tees and Reducing Crosses Outside diameter of reducing Tees & Crosses 40 x 40 x x 40 x x 40 x x 40 x x 40 x x 40 x x 40 x x 42 x x 42 x x 42 x x 42 x x 42 x x 42 x x 42 x x 42 x x 42 x x 42 x x 42 x x 42 x x 42 x x 44 x x 44 x Centre-end lengths Tees & Crosses GENERL NOTE: imensions are in mm 3.17
19 Section 3. SME 16.9 Fittings Table 3.4 imensions of Reducing Tees and Reducing Crosses Outside diameter of reducing Tees & Crosses 44 x 44 x x 44 x x 44 x x 44 x x 44 x x 44 x x 44 x x 44 x x 44 x x 44 x x 46 x x 46 x x 46 x x 46 x GENERL NOTE: imensions are in mm 3.18 Centre-end lengths Tees & Crosses
20 Table 3.4 imensions of Reducing Tees and Reducing Crosses Outside diameter of reducing Tees & Crosses 46 x 46 x x 46 x x 46 x x 46 x x 46 x x 46 x x 46 x x 46 x x 48 x x 48 x x 48 x x 48 x x 48 x x 48 x x 48 x x 48 x x 48 x x 48 x x 48 x x 48 x x 48 x Centre-end lengths Tees & Crosses GENERL NOTE: imensions are in mm 3.19
21 Section 3. SME 16.9 Fittings Table 3.5 imensions of Caps Outside iameter at Length (1) Limiting wall Length (2) evel 1 thickness for 2 length 1 Min. Nom. Max. ½ ¾ ¼ ½ ½ ½ GENERL NOTE: imensions are in mm 3.20
22 Table 3.5 imensions of Caps Outside iameter at Length (1) Limiting wall Length (2) evel 1 thickness for 2 length 1 Min. Nom. Max GENERL NOTES: imensions are in mm (1) Length 1 applies for thickness not exceeding that given in column Limiting Wall Thickness for Length (2) Length 2 applies for thickness greater than given in column Limiting Wall Thickness for Length 1 for NPS 24 and smaller. For NPS 26 and larger, length 2 shall be by agreement between manufacturer and purchaser.
23 Section 3. SME 16.9 Fittings Table 3.6 imensions of Reducers ¾ x ½ ¾ x x ¾ x ½ ¼ x ¼ x ¾ ¼ x ½ ½ x 1¼ ½ x ½ x ¾ ½ x ½ x 1½ x 1¼ x GENERL NOTE: imensions are in mm 3.22 O.. of Large End O.. of Small End End-to-End Length of Reducers Min. Nom. Max.
24 Table 3.6 imensions of Reducers O.. of Large End O.. of Small End End-to-End Length of Reducers Min. Nom. Max. 2 x ¾ ½ x ½ x 1½ ½ x 1¼ ½ x x 2½ x x 1½ x 1¼ ½ x ½ x 2½ ½ x ½ x 1½ ½ x 1¼ x 3½ x x 2½ x x 1½ x x 3½ x GENERL NOTE: imensions are in mm 3.23
25 Section 3. SME 16.9 Fittings Table 3.6 imensions of Reducers 5 x 2½ x x x x 3½ x x 2½ x x x x 3½ x x x GENERL NOTE: imensions are in mm 3.24 O.. of Large End O.. of Small End End-to-End Length of Reducers Min. Nom. Max.
26 Table 3.6 imensions of Reducers O.. of Large End O.. of Small End End-to-End Length of Reducers Min. Nom. Max. 10 x x x x x x x x x x x x x x x x x x x x x x GENERL NOTE: imensions are in mm 3.25
27 Section 3. SME 16.9 Fittings Table 3.6 imensions of Reducers 22 x x x x x x x x x x x x x x GENERL NOTE: imensions are in mm 3.26 O.. of Large End O.. of Small End End-to-End Length of Reducers Min. Nom. Max.
28 Table 3.6 imensions of Reducers O.. of Large End O.. of Small End End-to-End Length of Reducers Min. Nom. Max. 28 x x x x x x x x x x x x x x x x x x x x x x GENERL NOTE: imensions are in mm 3.27
29 Section 3. SME 16.9 Fittings Table 3.6 imensions of Reducers 38 x x x x x x x x x x x x x x GENERL NOTE: imensions are in mm 3.28 O.. of Large End O.. of Small End End-to-End Length of Reducers Min. Nom. Max.
30 Table 3.6 imensions of Reducers O.. of Large End O.. of Small End End-to-End Length of Reducers Min. Nom. Max. 44 x x x x x x x x x x x GENERL NOTE: imensions are in mm 3.29
Caps STANDARD WEIGHT Inches / Pounds
Standard Caps you are here: Home > Weldbend Catalog > Fittings > Caps Caps STANDARD WEIGHT Inches / Pounds For Metric Units >Click Here Nominal Pipe Size Outside Inside Wall Thickness (T) Length (E) Pipe
ASTM A860/A860M-09 Standard Specification for Wrought High Strength. Ferritic Steel Butt Welding Fittings. 1. Scope :- 2. Reference Documents :-
Standard Specification for Wrought High Strength Ferritic Steel Butt Welding Fittings 1. Scope :- 1.1 This specification covers wrought high strength ferritic steel butt-welding fitting of seamless and
RING JOINT SYSTEMS 207
RING JOINT SYSTEMS 07 08 Table of Contents Model R-88 Pages 10-11 Model R-88 Large Diameter Page 1 Model RH-1000 1000 PSI Coupling Page 13 Model RX-3000 3000 PSI Coupling Page 1 Model RX-3770 3770 PSI
TABLE OF CONTENTS 2 Heavy-Wall Seamless & Welded Carbon Steel Pipe. 4 Alloy Pipe & Tube. 6 Chrome-Moly Pipe. 7 Low-Temp Pipe
PRODUCT CATALOG TABLE OF CONTENTS 2 Heavy-Wall Seamless & Welded Carbon Steel Pipe 4 Alloy Pipe & Tube 6 Chrome-Moly Pipe 7 Low-Temp Pipe 9 Services amerpipe.com 1.800.316.5737 sales@amerpipe.com 18333
SPECIFICATIONS FOR STEEL PIPE
SPECIFICATIONS FOR STEEL PIPE Published pipe standards serve three functions. 1. They dictate manufacturing and testing requirements and prescribed methods of measuring the required mechanical and physical
Factory-Made Wrought Buttwelding Fittings
(Revision of ASME B16.9-2007) Factory-Made Wrought Buttwelding Fittings AN AMERICAN NATIONAL STANDARD (Revision of ASME B16.9-2007) Factory-Made Wrought Buttwelding Fittings AN AMERICAN NATIONAL STANDARD
ASME/ANSI B16.1-1998 - Cast Iron Pipe Flanges and Flanged Fittings ASME/ANSI B16.3-1998 - Malleable Iron Threaded Fittings ASME/ANSI B16.
ASME/ANSI B16.1-1998 - Cast Iron Pipe Flanges and Flanged Fittings ASME/ANSI B16.3-1998 - Malleable Iron Threaded Fittings ASME/ANSI B16.4-1998 - Cast Iron Threaded Fittings ASME/ANSI B16.5-1996 - Pipe
JIS G3461 Carbon Steel Tubes for Boiler and Heat Exchanger
JIS G3461 Carbon Steel Tubes for Boiler and Heat Exchanger 1. Scope This Japanese Industrial Standard specifies the carbon steel tubes, hereinafter referred to as the "tubes", used for exchanging heat
JIS G3445 Carbon steel tubes for machine structural purposes
JIS G3445 arbon steel tubes for machine structural purposes 1. Scope This Japanese Industrial Standard specifies the carbon steel tubes, hereinafter referred to as the "tubes", used for machinery, automobiles,
Series 4000 Fiberglass Pipe and Fittings
Series 4000 Fiberglass Pipe and Fittings for corrosive industrial service Uses and applications Listings Performance Acid drains Chemical process piping Corrosive slurries Food processing Geothermal Nonoxidizing
BROEN UNiFlEx FiTTiNgs FOR BURNiNg gases OEN OEN ifl ifl FOR FOR BURN BURN gas gas
BROEN UNIFLEX Fittings FOR BURNIN ASES BROEN UniFlex TM Fittings for burning gases BROEN UniFlex TM Fittings for burning gases LAB Table of Contents Content Page Table of Content 2 Product Overview 3 BROEN
JIS G3472 Electric Resistance Welded Carbon Steel Tubes for Automobile Structural Purposes
JIS G3472 Electric Resistance Welded Carbon Steel Tubes for Automobile Structural Purposes 1. Scope This Japanese Industrial Standard specifies the electric resistance welded carbon steel tubes, hereinafter
Copper-Nickel Mill Products
Copper-Nickel Mill Products Copper-Nickel Rod, Sheet, Plate, and Tubing ALASKAN COPPER & BRASS COMPANY History W hen Alaskan Copper Works was founded as a marine coppersmithing company in 9, one of its
Seamless stainless tubes for hydraulic and instrumentation systems
Seamless stainless tubes for hydraulic and instrumentation systems stock assortment integrated production technical knowledge network of sales and service Reduce your lifecycle costs When selecting tubes
Rubber Lining for Projects
Rubber Lining for Projects Trelleborg Rubber Lining - the ONE safeguard for wear and corrosion protection Trelleborg Rubber Linings can be applied to many surfaces to significantly reduce abrasive wear,
Introduction 9 TABLE - 1. Wrought alloys : Near equivalent designations
Introduction 9 TLE 1 Wrought alloys : Near equivalent designations 10 Introduction TLE2 Wrought alloys : Guide to selection lloy E/1050, 1060 (1) (19501) (19500) (19600) 1100 (1) (19000) Temper Resistance
AISI CHEMICAL COMPOSITION LIMITS: Nonresulphurized Carbon Steels
AISI CHEMICAL COMPOSITION LIMITS: Nonresulphurized Carbon Steels AISI No. 1008 1010 1012 1015 1016 1017 1018 1019 1020 1021 1022 1023 1024 10 1026 1027 1029 10 1035 1036 1037 1038 1039 10 1041 1042 1043
Tubing Data. Contents. Tubing Selection. Tubing Handling. Tubing Material. Tubing Outside Diameter Hardness. Tubing Wall Thickness
www.swagelok.com Tubing Data Contents Tubing Selection... 1 Tubing Handling.... 1 Gas Service... 2 Tubing Installation.... 2 Suggested Allowable Working Pressure Tables Carbon Steel Tubing... 3 Stainless
Enhanced version of 316/316L austenitic stainless steel. Better material performance at a lower cost. Juha Kela 16.6.2014. Juha Kela / 316plus
Enhanced version of 316/316L austenitic stainless steel. Better material performance at a lower cost. Juha Kela 16.6.2014 8 July 2014 1 Lower cost 8 July 2014 2 Lower cost 316 plus is available at lower,
60.12. Depend-O-Lok FxE Expansion Coupling. System No. Submitted By Spec Sect Para Location Date Approved Date. DEPEND-O-LOK FxE EXPANSION COUPLING
60.1 D-O-L FxE expansion couplings are a bolted, split-sleeve design that provides for expansion and contraction at the coupled joint. These couplings are furnished with restraint rings that, when affixed
Oil Dampers with Fixings on. Both Ends. Damping Engineering Oil Dampers with Fixings on Both Ends. Technical Data
amping Engineering Oil ampers with Fixings on Both Ends Oil dampers with fixings on both ends are used when moving objects may not exceed a certain speed e.g. flaps, lids, lever arms. They are fixed at
GUARDRAIL POST STEEL
GUARDRAIL POST STEEL Guardrail posts meeting materials certification are evaluated and checked for: 1. Dimensional acceptance 2. Physical test results a. Chemical b. Physical 3. Galvanized or painted coating
www.klmtechgroup.com TABLE OF CONTENT
Page : 1 of 45 Project Engineering Standard www.klmtechgroup.com KLM Technology #03-12 Block Aronia, Jalan Sri Perkasa 2 Taman Tampoi Utama 81200 Johor Bahru Malaysia TABLE OF CONTENT 1.0 SCOPE 2 2.0 CONFLICTS
When to use Weldolets... 4,5. Quality Control... 6. How to Order and Specify Branch Connections... 7. Weldolet... 8-14. Standard...
BRANCH CONNECTIONS Table Of Contents When to use Weldolets... 4,5 Quality Control... 6 How to Order and Specify Branch Connections... 7 Weldolet... 8-14 Standard... 8,9 Extra Strong... 10,11 Schedule 160/XX
High Density Polyethylene Liners for Rehabilitation of Corroded Pipelines
High Density Polyethylene Liners for Rehabilitation of Corroded Pipelines Jeff Schell General Manager United Pipeline Middle East, Inc. Introduction HDPE Liners A cost effective and environmentally beneficial
FLUROPIPE. POLYFLURON -PTFE lined Steel Pipes and Fittings ASME. Process Technology. Broad Base. Best Solutions.
FLUROPIPE POLYFLURON -PTFE lined Steel Pipes and Fittings ASME Process Technology Broad Base. Best Solutions. CCarbon is Future. SGL Group The Carbon Company. Process Technology The Business Unit Process
A World Class Manufacturer of Induction Bends
A World Class Manufacturer of Induction Bends COFELY FABRICOM BENDING A leading position in bending High Flexibility and Close Tolerances As a world leading manufacturer of pipe bends, produced by induction
Mechanical Property Changes in Steel during the Pipe Making Process Brent Keil 1
381 Mechanical Property Changes in Steel during the Pipe Making Process Brent Keil 1 Abstract Welded Steel Pipe (WSP) is arguably the most widely utilized pipe material for the transmission of water throughout
Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges 1
Designation: F 1545 97 e1 An American National Standard Standard Specification for Plastic-Lined Ferrous Metal Pipe, Fittings, and Flanges 1 This standard is issued under the fixed designation F 1545;
pvc well casing & drop pipe
CertainTeed pvc well casing & drop pipe PVC Well Products Sure Fit PVC well casing and drop pipe have gained broad acceptance since their introduction almost 40 years ago. Today, due to its outstanding
Uni-Quick Duct System. Moveable. Uni-Quick. Duct System. DUST COLLECTION and MATERIAL HANDLING APPLICATIONS a McGill AirFlow product
United McGill products Uni-Quick TM An enterprise of United McGill Corporation Family owned and operated since 1951 Moveable Duct System DUST COLLECTION and MATERIAL HANDLING APPLICATIONS a McGill AirFlow
External Wrapping of Steel Riser Pipe. Case Study HJ3 CS200902
External Wrapping of Steel Riser Pipe Case Study HJ3 CS200902 Introduction Refineries process a wide variety of petroleum products. As part of the process, they rely on cooling towers, which recycle water
Specification for Rotary Drill Stem Elements
Addendum 1 March 2007 Effective Date: September 1, 2007 Specification for Rotary Drill Stem Elements ANSI/API SPECIFICATION 7-1 FIRST EDITION, MARCH 2006 EFFECTIVE DATE: SEPTEMBER 2006 ISO 10424-1:2004
EDEXCEL NATIONAL CERTIFICATE/DIPLOMA MECHANICAL PRINCIPLES OUTCOME 2 ENGINEERING COMPONENTS TUTORIAL 1 STRUCTURAL MEMBERS
ENGINEERING COMPONENTS EDEXCEL NATIONAL CERTIFICATE/DIPLOMA MECHANICAL PRINCIPLES OUTCOME ENGINEERING COMPONENTS TUTORIAL 1 STRUCTURAL MEMBERS Structural members: struts and ties; direct stress and strain,
ALLOY 2205 DATA SHEET
ALLOY 2205 DATA SHEET UNS S32205, EN 1.4462 / UNS S31803 GENERAL PROPERTIES ////////////////////////////////////////////////////// //// 2205 (UNS designations S32205 / S31803) is a 22 % chromium, 3 % molybdenum,
ENGINEERING COUNCIL CERTIFICATE LEVEL
ENGINEERING COUNCIL CERTIICATE LEVEL ENGINEERING SCIENCE C103 TUTORIAL - BASIC STUDIES O STRESS AND STRAIN You should judge your progress by completing the self assessment exercises. These may be sent
Material data sheet. EOS StainlessSteel GP1 for EOSINT M 270. Description, application
EOS StainlessSteel GP1 for EOSINT M 270 A number of different materials are available for use with EOSINT M systems, offering a broad range of e-manufacturing applications. EOS StainlessSteel GP1 is a
Tubular solutions for the Solar Power Industry Rise in success with precision
Tubular solutions for the Solar Power Industry Rise in success with precision A comprehensive offer Precision tubes designed for CSP industry applications Solar collectors q Tubes adapted for solar heat
Ventilstandarder ett urval av standarder
EN 19:2002 EN 558:2008+A1:2011 EN 593:2009+A1:2011 EN 736-1:1995 EN 736-2:1997 EN 736-3:2008 EN 1074-1:2000 EN 1074-2:2000, A1:2004 EN 1074-3:2000 EN 1074-4:2000 EN 1075-5:2001 EN 1074-6:2008 EN 1171:2002
HUS-HR Stainless steel Concrete Screw A4 316. CE conformity. Corrosion resistance. European Technical Approval
HUS-HR screw anchor Anchor version Benefits HUS-HR Stainless steel Concrete Screw Quick and easy setting Low expansion forces in base materials Through fastening Removable Forged-on washer and hexagon
Heat Pipe Selection Revision 12/04/2001
Heat Pipe Selection Revision 12/04/2001 Heat pipes are being used very often in particular applications when conventional cooling methods are not suitable. Once the need for heat pipe arises, the most
HYDRAULIC PIPING STANDARD HANDBOOK. Revision 1
HYDRAULIC PIPING STANDARD HANDBOOK Revision 1 Preface We aim to fill a gap in technical literature. At this moment there are no hydraulic piping standards available which cover different pressure classes
Urea and Nitric Acid Plants: Improvement of Shut-Down, Revamping, Debottlenecking and Refurbishment
pp Urea and Nitric Acid Plants: Improvement of Shut-Down, Revamping, Debottlenecking and Refurbishment J. M. SLUYTERS GEMACO SA Herstal, Belgium A presentation on special corrosion-resistant steels for
MECHANICAL PRINCIPLES HNC/D PRELIMINARY LEVEL TUTORIAL 1 BASIC STUDIES OF STRESS AND STRAIN
MECHANICAL PRINCIPLES HNC/D PRELIMINARY LEVEL TUTORIAL 1 BASIC STUDIES O STRESS AND STRAIN This tutorial is essential for anyone studying the group of tutorials on beams. Essential pre-requisite knowledge
Schedule 40 & Schedule 80 Rigid PVC Piping Systems Scroll Down for Dimensions, Components, Hangars & Supports, Fabrication Techniques
Schedule 40 & Schedule 80 Rigid PVC Piping Systems Scroll Down for Dimensions, Components, Hangars & Supports, Fabrication Techniques Schedule 40 Rigid PVC Piping Systems SCHEDULE 40 - DIMENSIONS Harvel
2005 WJTA American Waterjet Conference August 21-23, 2005 Houston, Texas Paper SAFE WATERJET CLEANING OF STEEL PROCESS LINES
25 WJTA American Waterjet Conference August 21-23, 25 Houston, Texas Paper SAFE WATERJET CLEANING OF STEEL PROCESS LINES D. Wright, J. Wolgamott, G. Zink StoneAge, Inc. Durango, Colorado, U.S.A. ABSTRACT
Scraper Passage Indicator. Electrical Indicator. Features
IV Scraper Passage Indicator Bulletin No: 5110.001.03 Date: June 2008 Cross Indexing No: n/a Supersedes: 5110.001.02 (1/06) Flag Indicator Electrical Indicator Options Description TDW s IV Scraper Passage
DESCRIPTION. Stud Bolts for Pressure-Temperature Piping 2-1. General Purpose End-to-End Studs 2-2. Tap End Stud Bolts 2-3. Double End Stud Bolts 2-4
DESCRIPTION PAGE B7 Studs and Nuts Stud Bolts for Pressure-Temperature Piping 2-1 General Purpose End-to-End Studs 2-2 Tap End Stud Bolts 2-3 Double End Stud Bolts 2-4 Sigma Fasteners, Inc. Section 2 STUD
Technical Notes 3B - Brick Masonry Section Properties May 1993
Technical Notes 3B - Brick Masonry Section Properties May 1993 Abstract: This Technical Notes is a design aid for the Building Code Requirements for Masonry Structures (ACI 530/ASCE 5/TMS 402-92) and Specifications
HOSE, TUBE, AND PIPE CLAMPS
hose, tube & clamp B/W pages 24/6/08 9:28 AM Page 2 HOSE, TUBE, AND PIPE CLAMPS TABLE OF CONTENTS Introduction 3 Construction 3 Application 3 Mounting 3 Standard Duty Clamps (HRL) Arrangements 4 Dimensions
DIN 2391-81 Part II SEAMLESS PRECISION STEEL TUBES
DIN 91-81 Part II SEAMLESS PREISION STEEL TUBES 1.Field of application This defines the technical delivery conditions for seamless precision steel tubes according to DIN 91 Part 1 which are made from the
PIPING SYSTEM - ABRASIVE SLURRIES Engineering Standard Specification. 96 B. Riutta
PIPING SYSTEM - ABRASIVE SLURRIES Engineering Standard Specification Number: 3503-11.2.610 Rev. 2 Rubber Lined Steel Pipe and Fittings Mechanically Coupled Plain End Type System Issued Revised Approved
www.klmtechgroup.com TABLE OF CONTENT
Page : 1 of 10 Project Engineering Standard www.klmtechgroup.com KLM Technology #03-12 Block Aronia, Jalan Sri Perkasa 2 Taman Tampoi Utama 81200 Johor Bahru Malaysia TABLE OF CONTENT SCOPE 2 REFERENCES
Africa s leading steel supplier CATALOGUE TUBE & PIPE. The Macsteel Group - Africa s leading steel supplier - www.macsteel.co.za
Africa s leading steel supplier CATALOGUE TUBE & PIPE - www.macsteel.co.za TUBE & PIPE CONTENTS 1. Contents 13. Conveyance SANS 1182 - Light Page 7 2. Contact Details 14. Conveyance SANS 719 - Large Bore
Heat Exchanger Thin Film Foul Release Applications Corrosion Resistant Protective Coatings Grit Blast Surface Prep of Tubular Equipment
Heat Exchanger Thin Film Foul Release Applications Corrosion Resistant Protective Coatings Grit Blast Surface Prep of Tubular Equipment Non-Destructive Examination Heat Exchanger Mechanical Repair Services
Profiles in stock Standard catalogue. Discover the possibilities with aluminium profiles from Sapa
Profiles in stock Standard catalogue Discover the possibilities with aluminium from Sapa You can create your own profile or you can choose from a wide selection of standard. Delivery: 1 2 weeks for standard
Burst Pressure Prediction of Pressure Vessel using FEA
Burst Pressure Prediction of Pressure Vessel using FEA Nidhi Dwivedi, Research Scholar (G.E.C, Jabalpur, M.P), Veerendra Kumar Principal (G.E.C, Jabalpur, M.P) Abstract The main objective of this paper
Waterstops play a critical role in the integrity of concrete
J P SPECIALTIES, INC. www.facebook.com/waterstop Section 03150 MasterFormat 03 15 13 Metallic Waterstop for Extreme Chemical & Heat Resistance Waterstops play a critical role in the integrity of concrete
ALLOY C276 DATA SHEET
ALLOY C276 DATA SHEET //// Alloy C276 (UNS designation N10276) is a nickel-molybdenum-chromium-iron-tungsten alloy known for its corrosion resistance in a wide range of aggressive media. It is one of the
Company and Product Presentation
Company and Product Presentation Company Presentation NBG Systems & FCT are private companies owned by NBG Holding Both are Austrian companies, operating under the highest European Union requirements &
GOST 632-80 CASING AND COUPLINGS
GOST 632-80 CASING AND COUPLINGS Casing to this standard shall be seamless, with round and buttress-type threads (OTTM-type casing), with high-seal thread connection (OTTG-type casing) and respective couplings;
2013 Edition. Flanged fittings 30"-64" NSF. industrial Applications, water & Wastewater. Certified to ANSI/NSF 61
30"-64" Ductile Iron industrial Applications, water & Wastewater 2 Table of Contents Flanged Fittings for Water 3 Flange Details 5 Flanged Fittings 6 90º and 45º Bend 6 22-1/2º and 11-1/4º Bends 7 Tees
SECTION 15076 CEMENT-MORTAR LINED AND COATED STEEL PIPE
SECTION 15076 CEMENT-MORTAR LINED AND COATED (CML&C) STEEL PIPE PART 1 GENERAL 1.01 DESCRIPTION This section designates the requirements for steel pipe fabrication, test in shop, installation of steel
Forged Fittings, Socket-Welding and Threaded
SME 16.11-2005 (Revision of SME 16.11-2001) Forged Fittings, Socket-Welding and Threaded N M E R I N N T I O N L S T N R Provided by IHS under license with SME SME 16.11-2005 (Revision of SME 16.11-2001)
STAVAX SUPREME. Stainless tool steel
STAVAX SUPREME Stainless tool steel General Demands placed on plastic mould tooling are increasing. Such conditions require mould steels that possess a unique combination of toughness, corrosion resistance
Stainless steel grade chart
Stainless steel grade chart ATLAS STEELS METAL DISTRIBUTION Chemical analysis (%) specified C Si Mn P S Cr Mo Ni Other Austenitic stainless steels 253MA S30815 0.05 1.1-2.0 0.8 0.040 0.030 20.0-22.0 10.0-12.0
Premium Tubular Solutions Super Duplex Welded Tubes for Umbilical Applications
Premium Tubular Solutions Super Duplex Welded Tubes for Umbilical Applications Premium Tubular Solutions Innovative Tubes for Umbilical Applications Over 35 years of experience in Premium welded t ubular
Hilti, Inc. 5400 South 122 nd East Avenue Tulsa, OK 74146. 1-800-879-8000 www.hilti.com
Attached are page(s) from the 2014 Hilti North American Product Tech Guide. For complete details on this product, including data development, product specifications, general suitability, installation,
DIN 17172-78 STEEL PIPES FOR PIPE LINES FOR THE TRANSPORT OF COMBUSTIBLE FLUIDS AND GASES
DIN 17172-78 STEEL PIPES FOR PIPE LINES FOR THE TRANSPORT OF COMBUSTIBLE FLUIDS AND GASES For connection with the International Draft Standards 3183 and 3845 published by the International Organization
SECTION 33 11 00.15 DUCTILE IRON PIPE AND FITTINGS
SECTION 33 11 00.15 DUCTILE IRON PIPE AND FITTINGS PART 1: GENERAL 1.01 COORDINATION OF WORK Connection to existing pipelines may require shutdown of AW facilities. Closely coordinate construction work
SUBMITTAL 10 FEET. Cast Iron Soil Pipe Products Hubless Pipe & Fittings HUBLESS PIPE 10 FEET*
QUALITY SYSTEM SUBMITTAL Hubless Pipe & Fittings R E G I S T R AT I O N Manufacturer s T J B 10 FEET HUBLESS PIPE 10 FEET* NOM. SIZE B INSIDE DIAMETER J OUTSIDE DIAMETER 1 1/2 1.50 1.90 0.16 0.13 28.4
Fittings, Tubing & Nipples
s, Tubing & Nipples P Series Pipe s s to 15,000 psi (1034 bar) Since 1945 Parker utoclave Engineers has designed and built premium quality valves, fittings and tubing. This commitment to engineering and
HUS-A 6 / HUS-H 6 / HUS-I 6 / HUS-P 6 Screw anchor in precast prestressed hollow core slabs
HUS-A 6 / HUS-H 6 / HUS-I 6 / HUS-P 6 Screw anchor in precast Anchor version HUS-A 6 Screw with hex head HUS-H 6 Screw with hex head HUS-I 6 Screw with hex head Benefits - Quick and easy setting - Low
TRANSPORTATION PIPELINE SYSTEMS FOR LIQUID HYDROCARBONS Code of Practice
ICS 75.200 PUBLIC COMMENTS DRAFT Draft Zambian Standard TRANSPORTATION PIPELINE SYSTEMS FOR LIQUID HYDROCARBONS Code of Practice This standard is for public comments only. It must not be used or referred
INFORMAZIONI GENERALI / GENERAL INFORMATION
INFORMAZIONI GENERALI / GENERAL INFORMATION LE FLANGE DELLA SOCIETà INTERTUBI SONO FORNITE IN ACCORDO ALLE SEGUENTI NORME: INTERTUBI S FLANGES ARE PROVIDED IN ACCORDING WITH THE FOLLOWINGS STANDARDS Norma
www.klmtechgroup.com TABLE OF CONTENT
Page : 1 of 16 Project Engineering Standard www.klmtechgroup.com KLM Technology #03-12 Block Aronia, Jalan Sri Perkasa 2 Taman Tampoi Utama 81200 Johor Bahru Malaysia ORIFICE FLANGES TABLE OF CONTENT SCOPE
Pressure Vessels (Air Compressors) and LPG Tanks
Pressure Vessels (Air Compressors) and LPG Tanks 1. Identification of Workplace Hazard Any container, tank or vessel that contains pressurized material is a potential hazard to employees due to the force
RISK BASED INSPECTION (RBI)
1 RISK BASED INSPECTION (RBI) Roy Johnsen Professor, Institutt for produktutvikling og materialer (IPM), NTNU Roy.johnsen@ntnu.no Tlf: +47 93245101 2 CONTENT Introduction - Corrosion Management What is
Green Thread Product Data
Green Thread Product Data Applications Dilute Acids Caustics Produced Water Industrial Waste Hot Water Condensate Return Materials and Construction All pipe manufactured by filament winding process using
EDEXCEL NATIONAL CERTIFICATE/DIPLOMA MECHANICAL PRINCIPLES AND APPLICATIONS NQF LEVEL 3 OUTCOME 1 - LOADING SYSTEMS TUTORIAL 3 LOADED COMPONENTS
EDEXCEL NATIONAL CERTIICATE/DIPLOMA MECHANICAL PRINCIPLES AND APPLICATIONS NQ LEVEL 3 OUTCOME 1 - LOADING SYSTEMS TUTORIAL 3 LOADED COMPONENTS 1. Be able to determine the effects of loading in static engineering
Armanet BEKAERT. Armanet THE CONSTRUCTIVE IDEA. Render & plaster reinforcing mesh @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@ @@@
BEKAERT Armanet THE CONSTRUCTIVE IDEA Armanet Render & plaster reinforcing mesh Armanet Renovation Product specification Insulation Reinforcing Mesh Armanet is a heavily galvanized welded mesh used for
Standard Specification for Stainless Steel Bars and Shapes 1
Designation: A 276 06 Standard Specification for Stainless Steel Bars and Shapes 1 This standard is issued under the fixed designation A 276; the number immediately following the designation indicates
FITTINGS 5-01. 82A series Aluminium (light weight) compression fittings Ø 6... 42 mm tube size, BSPP and BSPT thread
FITTINS 82 series luminium (light weight) compression fittings Ø 6... 42 mm tube size, SPP and SPT thread 82 series rass compression fittings Ø 6... 42 mm tube size, SPP and SPT thread 83 series luminium
Pipe Flow-Friction Factor Calculations with Excel
Pipe Flow-Friction Factor Calculations with Excel Course No: C03-022 Credit: 3 PDH Harlan H. Bengtson, PhD, P.E. Continuing Education and Development, Inc. 9 Greyridge Farm Court Stony Point, NY 10980
Technical Report Example (1) Chartered (CEng) Membership
Technical Report Example (1) Chartered (CEng) Membership A TECHNICAL REPORT IN SUPPORT OF APPLICATION FOR CHARTERED MEMBERSHIP OF IGEM DESIGN OF 600 (103 BAR) 820MM SELF SEALING REPAIR CLAMP AND VERIFICATION
Pipe threads for tubes and fittings where pressure-tight joints are not made on the threads. (requires PTFE sealing tape or liquid sealant).
Fittings for CO 2 Pipe Threads Pipe thread references quoted in this catalogue conform with the requirements specified in the latest issue and amendments of the following ISO Standards: ISO 7-1 (BS21)
Lap Fillet Weld Calculations and FEA Techniques
Lap Fillet Weld Calculations and FEA Techniques By: MS.ME Ahmad A. Abbas Sr. Analysis Engineer Ahmad.Abbas@AdvancedCAE.com www.advancedcae.com Sunday, July 11, 2010 Advanced CAE All contents Copyright
Pressure vessel basics for all engineers
Pressure vessel basics for all engineers by Sharjeel Aslam Faiz 1. Contents 2. Preliminary Design... 3 3. Loads... 3 4. Detailed design... 3 5. Information in-flow to a fabrication drawing... 4 6. Information
SIZING AND CAPACITIES OF GAS PIPING
APPENDIX A (IFGS) SIZING AND CAPACITIES OF GAS PIPING (This appendix is informative and is not part of the code.) A.1 General. To determine the size of piping used in a gas piping system, the following
Flanged and Butt-= Weld Type
Document : PG00 Year : 09 Product Group 00 Flanged and Butt-= Weld Type (LNG and LPG) Page 09 Document : PG00 Year : 09 Product Group 00 Cryogenic Butterfly valves The Cryogenic Butterfly Valve Design
TECHNICAL SPECIFICATION
THOMAS - G-FLEX GFLEX TECH SPEC CONNECTING INNOVATION JOHANNESBURG TEL: +27 11 794 7594 CAPE TOWN TEL: +27 21 556 5258 POLOKWANE TEL: 015 298 9142 DESIGNER, MANUFACTURER AND DISTRIBUTOR OF PIPE CONNECTION,
Stainless Steel Tubular Products
Stainless Steel Tubular Products r Disclaimer This Data is indicative only and as such is not to be relied upon in place of the full specification. In particular, mechanical property requirements vary
09/07/07 GLASSFIBER REINFORCED CEMENT (GRC) C. S. I. Spec 03500 Master Spec. 03 49 00 Page 1
C. S. I. Spec 03500 Page 1 PART 1 - GENERAL 1.01 SUMMARY:.01 Provide special glassfiber reinforced cement (GRC) shapes in accordance with the requirements of the contract documents..02 The installing contractor
Non-invasive CLAMP-ON ultrasonic flowmeter for liquids
Non-invasive CLAMP-ON ultrasonic flowmeter for liquids Model CU100: non-invasive installation flowmeter, with transducers installed outside the pipe Installation in horizontal or vertical pipe Easy and
Tolerance +/- 0,5 mm, +/- 0,2 mm. Length 15-350 mm ( standard) SLOTS. 9 5/8 x 36 Ibs/ft. 4 1/2 x 9,5 Ibs/ft. Slotted casing
Slotted casing Tube API 5CT, grade J/K55, R1, R2, STC: 4 1/2 x 9,5 Ibs/ft number of slots / meter number of ranges on circumference number of ranges per linear meter 24 4 6 9 5/8 x 36 Ibs/ft 48 8 6 Slotted