Reference Book. Steel Service Centre
|
|
|
- Alfred Shields
- 9 years ago
- Views:
Transcription
1 Reference Book Steel Service Centre
2 PROCESSING SERVICES CAD-CAM - Drafting system, which gives computer-aided design, and manufacturing for solid state electronically controlled mutely-torch units. In addition, it provides computerized filing for future re-orders or reference. SAWCUTTING - N.C. - controlled high-speed band saws for cutting to exact lengths. Mitre cutting available. SPLIT TEES - Oxy-Fuel beam splitting available. FLAME CUTTING CUSTOM SAW CUTTING Angles Flat Bar Beams Channels Carbon Plate Rebar Abrasion Resistant Plate Quenched & Tempered Plate Grating Expanded Metal Steel Pipe Concrete Wire Mesh Hollow Structural Tubing
3 Street, N.W. Edmonton, Alberta T5V 1L3 Toll Free Line Tel: Fax: Website: i
4 Contents Pg. Rounds - Hot Rolled 1 Squares - Hot Rolled 2 Flats - Hot Rolled 3 & 4 Angles 5 & 6 Channels 7 Miscellaneous Channels 8 Ring Rolling Guideline 9 Beams I(S) 10 Beams WF Rounds - Cold Finish 16 Squares - Cold Finish 17 Reinforcing Bars 18 Grouser Bar Sheets - Hot Rolled 21 Plates Mechanical Properties of Plates 27 Metal Processing Selection Chart for Plate Shapes Expanded Metal Bar Grating / Stair Treads 36 Fastening Methods 37 Safety Grip/Diamond Grip 38 ASA Pipe Schedules Welded Steel Pipe Seamless Steel Pipe 44 Hollow Structural Sections Square Hollow Structural Sections Rectangular Reference Information ii
5 ROUNDS HOT ROLLED SPEC A-36/44W lbs./ft. 1/ / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / lbs./ft / / / / / / / / / / / / / / / / / / / / / / / / / / / / / /
6 SQUARES HOT ROLLED SPEC A-36/44W lbs./ft. 1/ / / / / / ½.850 9/ / / / / / / lbs./ft / / / / / / / / / / / / / / / / / / / /
7 FLATS HOT ROLLED SPEC A-36/44W lbs./ft. 1/8 x 1/ / / / / / / / lbs./ft. 1/4 x 1/ / / / / / / / / lbs./ft. 3/8 x 3/ / / / / / lbs./ft. 3/16 x 1/ / / / / / / lbs./ft. 1/8 x 1/ / / / / / / / lbs./ft. 3/8 x 3/ / / / / /
8 FLATS HOT ROLLED SPEC A-36/44W lbs./ft. 5/8 x / / / / lbs./ft. 7/8 x / / / / lbs./ft. 1-1/4 x 1-1/ lbs./ft. 3/4 x / / / / lbs./ft. 1 x 1-1/ / / lbs./ft. 1-1/4 x
9 ANGLES- BAR SIZE SPEC A-36/44W ANGLES STRUCTURAL SPEC A-36/44W Size Thickness Wt. lbs./ft. 1/2 x 1/2 1/8.38 5/8 x 5/8 1/8.48 3/4 x 3/4 1/8.59 3/ /8 x 7/8 1/ x 1 1/8.80 3/ / /4 x 1/4 1/ / / /2 x 11/2 1/ / / / / /4 x 13/4 1/ / / x 11/2 1/ / / / x 2 1/ / / / / /4 x 21/4 3/ / /2 x 2 1/ / / / / /2 x 21/2 1/ / / / / / / Size Thickness Wt. lbs./ft. 3 x 2 3/ / / / / / x 21/2 1/ / / / / x 3 1/ / / / / / / /2 x 21/2 3/ / / / / / /2 x 3 1/ / / / / /2 x 31/2 1/ / / / / x 3 1/ / / / / /
10 ANGLES STRUCTURAL SPEC A-36/44W Size Thickness Wt. lbs./ft. 4 x 31/2 1/ / / / / / x 4 1/ / / / / / / x 3 1/ / / / / x 31/2 1/ / / / / / / x 5 5/ / / / / / x 31/2 1/ / / / Size Thickness Wt. lbs./ft. 6 x 6 5/ / / / / / / / / x 4 3/ / / / / / / x 4 7/ / / / x 6 7/ / / / / / x 8 1/ / / / / / INQUIRE ABOUT OUR TRUCK DELIVERY FOR CONVENIENT TRANSPORT TO YOUR LOCATION 6
11 CHANNELS BAR SIZE SPEC A-36/44W Imperial Designation Metric Designation mm Weight lbs./ft. 1 x 1/2 x 1/ x 12.7 x /4 x 1/2 x 1/8 x 9/16 x 3/ x 12.7 x 3.2 x 14.3 x /2 x 1/2 x 1/8 x 9/16 x / x 12.7 x 3.2 x 14.3 x x 1 x 3/ x 25.4 x STANDARD CHANNELS SPEC A-36/44W New Designation 7 Flange Web Thickness In Section Modulus In 3 Old CDN Depth Width Thickness IMP. Metric In (mean) C3 x 4.1 C75 x x 5.0 x x 6.0 x C4 x 5.4 C100 X x 6.25 x x 7.25 x C5 x 6.7 C130 X x 9.0 x C6 x 8.2 C150 x x 10.5 x x 13.0 x C7 x 9.8 C180 X x x x x C8 x 11.5 C200 X x x x x C9 x 13.4 C230 x x 15.0 x x 20.0 x C10 x 15.3 C250 X x 20.0 x x 25.0 x x 30.0 x C12 x 20.7 C310 x x 25.0 x x 30.0 x C15 x 33.9 C380 x x 40.0 x x 50.0 x
12 MISCELLANEOUS CHANNELS SPEC A-36/44W New Designation Flange Old CDN Depth Width Thickness (mean) Web Thickness Section Modulus IMP. Metric In In In 3 MC3 x 7.1 MC75 x x 9.0 x MC6 x 12.0 MC150 x x 15.1 x x 15.3 x x 16.3 x x 18.0 x MC7 x 17.6 MC180 x x 19.1 x x 22.7 x MC8 x 8.5 MC200 x x 18.7 x x 20.0 x x 21.4 x x 22.8 x MC9 x 23.9 MC230 x x 25.4 x MC10 x 6.5 MC250 x x 8.4 x x 21.9 x x 24.9 x x 25.3 x x 28.3 x x 28.5 x x 33.6 x x 41.1 x MC12 x 10.6 MC310 x x 30.9 x x 32.9 x x 35.0 x x 37.0 x x 40.0 x x 45.0 x x 50.0 x MC13 x 31.8 MC330 x x 35.0 x x 40.0 x x 50.0 x MC18 x 42.7 MC460 x x 45.8 x x 51.9 x x 58.0 x
13 Ring Rolling Guideline 9
14 STANDARD BEAMS SPEC A-36/44W/A New Designation Flange Old CDN Depth Width Thickness Web (mean) Thickness Imp. Metric Section Modulus 3 S3 x 5.7 S75 x x 7.5 x S4 x 7.7 S100 x x 9.5 x S5 x 10.0 S130 x x x S6 x 12.5 S150 x x x S7 x 15.3 S180 x x 20.0 x S8 x 18.4 S200 x x 23.0 x S10 x 25.4 S250 x x 35.0 x S12 x 31.8 S310 x x 35.0 x S12 x 40.8 S310 x x 50.0 x S15 x 42.9 S380 x x 50.0 x S18 x 54.7 S460 x x 70.0 x S20 x 66.0 S510 x x 75.0 x S20 x 86.0 S510 x x 96.0 x S24 x 80.0 S610 x x 90.0 x x x S24 x S610 x x x
15 WIDE FLANGE BEAMS SPEC A-36/44W/A New Designation Flange Old Imp. CDN Metric Depth Width Thickness (mean) Web Thickness Section Modulus 3 W4 x 13 W100 x W5 x 16 W130 x x 19 x W6 x 9 W150 x x 12 x x 16 x W6 x 15 W150 x x 20 x x 25 x W8 x 10 W200 x x 13 x x 15 x W8 x 14 W200 x x 18 x x 21 x W8 x 24 W200 x x 28 x W8 x 31 W200 x x 35 x x 40 x x 48 x x 58 x x 67 x W10 x 12 W250 x x 15 x x 17 x x 19 x W10 x 16 W250 x x 22 x x 26 x x 30 x W10 x 33 W250 x x 39 x x 45 x W10 x 49 W250 x x 54 x x 60 x x 68 x x 77 x x 88 x x 100 x
16 WIDE FLANGE BEAMS SPEC A-36/44W/A New Designation Flange ASTM Imp. CDN Metric Depth Width Thickness (mean) Web Thickness Section Modulus W12 x 14 W310 x x 16 x x 19 x x 22 x W12 x 21 W310 x x 26 x x 30 x x 35 x W12 x 40 W310 x x 45 x x 50 x W12 x 53 W310 x x 58 x W12 x 65 W310 x x 72 x x 79 x x 87 x x 96 W310 x x 106 x x 120 x x 126 x x 152 x x 170 x x 190 x W12 x 210 W310 x x 230 x x 252 x x 279 x x 305 x x 336 x W14 x 22 W360 x x 26 x W14 x 30 W360 x x 34 x ,6 x 38 x W14 x 43 W360 x x 48 x x 53 x W14 x 61 W360 x x 68 x x 74 x x 82 x
17 WIDE FLANGE BEAMS SPEC A-36/44W/A New Designation Flange ASTM Imp. CDN Metric Depth Width Thickness (mean) Web Thickness Section Modulus 3 W14 x 90 W360 x x 99 x x 109 x x 120 x x 132 x W14 x 145 W360 x x 159 x x 176 x x 193 x x 211 x x 233 x x 257 x x 283 x x 311 x x 342 x x 370 x x 398 x x 426 x x 455 x x 500 x x 550 x x 605 x x 665 x x 730 x W16 x 26 W410 x x 31 x W16 x 36 W410 x x 40 x x 45 x x 50 x x 57 x W16 x 67 W410 x x 77 x x 89 x x 100 x
18 WIDE FLANGE BEAMS SPEC A-36/44W/A New Designation Flange ASTM CDN Depth Width Thickness Web (mean) Thickness Imp. Metric Section Modulus 3 W18 x 35 W460 x x 40 x x 46 x W18 x 41 W460 x x 45 x x 50 x x 55 x x 60 x x 65 x x 71 x W18 x 76 W460 x x 86 x x 97 x x 106 x x 119 x W21 x 44 W530 x x 50 x x 57 x W21 x 48 W530 x x 55 x x 62 x x 68 x x 73 x x 83 x x 93 x W21 x 101 W530 x x 111 x x 122 x x 132 x x 147 x W24 x 55 W1610 x x 62 x W24 x 56 W610 x x 61 x x 68 x x 76 x x 84 x x 94 x W24 x 104 W610 x x 117 x x 131 x x 146 x x 162 x
19 WIDE FLANGE BEAMS SPEC A-36/44W/A New Designation Flange ASTM CDN Depth Width Thickness Web (mean) Thickness Imp. Metric Section Modulus W27 x 84 W690 x x 94 x x 102 x x 114 x W27 x 146 W690 x x 161 x x 178 x W30 x 99 W760 x x 108 x x 116 x x 124 x x 132 x W30 x 173 W760 x x 191 x x 211 x W33 x 118 W840 x x 130 x x 141 x x 152 x W33 x 201 W840 x x 221 x x 241 x W36 x 135 W920 x x 150 x x 160 x x 170 x x 182 x x 194 x x 210 x W36 x 230 W920 x x 245 x x 260 x x 280 x x 300 x WE PROVIDE MILL TEST REPORTS FOR MOST PRODUCTS ON REQUEST 15
20 ROUNDS COLD FINISHED SPEC C1018 Size Wt. lbs./ft. Size Wt. lbs./ft. 1/ / / / / / / / / / / / / / / / / / / / / W / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / (16)
21 SQUARES COLD FINISHED SPEC C1018 Size Wt. lbs./ft. 1/ / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / / OTHER GRADES AVAILABLE COLD FINISHED FLATS - PLEASE ENQUIRE 17
22 Reinforcing Bars G400 W The nominal dimension of a deformed bar are equivalent to those of a plain METRIC STANDARD REINFORCING BARS NOMINAL DIMENSIONS - ROUND BARS BAR Cross Sectional MASS WEIGHT SIZE Diameter Area Perimeter Designation Kg/m lbs/ft mm In mm 3 In 3 mm In 10M M M M M M M M bar having the same mass per metre (weight per foot) as the deformed bar. STOCKED IN 6 METRE LENGTHS Bars are available in three grades providing different levels of strength. Minimum Minimum GRADE Tensile Strength Yield Strength MPa Ksl MPa Ks Yield Point
23 5 /8 " Grouser Bar BARS SUPPLIED IN 10 FOOT LENGTHS* 1/8" ¼ 5/16" 1" to ¾ scale 4" 1" IMPORTANT When ordering, please order by the letter or letters shown on the drawing of the size or sizes of the Grouser Bar that you require. 19
24 All sizes available in 10 lengths, some pre-cut sizes available. Heat treated to a hardness of Rc hardness to deliver optimum wear performance and toughness for extreme weather and working conditions. Carbon - boron steel facilitates ice lug weldability General Information 1. Sheffield - Butler Premium Grouser Bar is made a special high quality work hardening steel and becomes harder and tougher with use. 2. Strict control ensures high quality...always. 3. Gives more mileage under all operating conditions. 4. Reduces down time. 5. Rebuilds worn Grousers to original size and gripping power. 6. Application is simple, fast and economical either by hand or automatic welding. 7. Use in making coal or rock crusher screens or in repair of excavator buckets. 8. The thirteen sizes are supplied in 10 - foot lengths. Section R is available in heat treated pre-cut 32 lengths only. 9. Pre-cut ice lugs in sizes LS and L in stock. Other sizes available upon request. 10. Sheffield-Butler Premium Grouser Bar will save you money! 11. General welding procedures and bar specifications available upon request. 20
25 HOT ROLLED SHEETS Commercial Quality - ASTM A569 Weight Weight Size in Inches Per Sheet Size in Inches Per Sheet 16g. =.0598" = lbs. per sq. ft. 11 ga. =.1196" = 5.00 lbs. per sq. ft. 16 ga. 48 x ga. 48 x x x ga. =.0747" = lbs. per sq. ft. 72 x ga. 48 x ga. =.1345" = lbs. per sq. ft ga. 48 x x x x ga. =.1046" = lbs. per sq. ft. 72 x ga. 48 x x Weights may vary due to production tolerances. 72 x Please contact our sales department for special lengths. 21
26 ASTM - A36 OR CSA G W / 300W Steel Plates Weight Weight Size in Inches Per Sheet Size in Inches Per Sheet 3/16" =.1875" = 7.66 lbs. per sq. ft. 5/16" =.3125" = lbs. per sq. ft. 3/16" x /16" 48 x x x x x x x x x /4" =.250" = lbs. per sq. ft /" 48 x /8" =.375" = lbs. per sq. ft /8" 48 x x x x x x x x x x Size shown are not necessarily stock items and are shown for weight reference only. 120 x
27 ASTM - A36 OR CSA G W / 300W Steel Plates Weight Weight Size in Inches Per Sheet Size in Inches Per Sheet 1/2" =.500" = lbs. per sq. ft. 3/4" =.750" = lbs. per sq. ft. 1/2" x 48 x /4" x 48 x x x x x x x x x /8" =.875" = lbs. per sq. ft /8" x 48 x x /8" =.625" = lbs. per sq. ft /8" x 48 x x x x x x Please contact our Sales Department for special lengths We can flame cut to special lengths or widths 96 x Size shown are not necessarily stock items and are shown for weight reference only. 23
STOCK LIST & BUYER S GUIDE
STOCK LIST & BUYER S GUIDE common Decimal equivalents 1/64 =.0156 1/32 =.0312 1/16 =.0625 3/32 =.0937 1/8 =.125 3/16 =.1875 7/32 =.2187 1/4 =.250 9/32 =.2812 5/16 =.3125 3/8 =.375 7/16 =.4375 1/2 =.500
TARIFF CODE and updates standard
TARIFF CODE and updates standard No HS CODE AHTN CODE PRODUCT DESCRIPTION PRODUCT TYPE STANDARDS IDENTIFIED 7207 Semi finished products of iron or non alloy steel Containing by weight less than 0.25% of
AISI CHEMICAL COMPOSITION LIMITS: Nonresulphurized Carbon Steels
AISI CHEMICAL COMPOSITION LIMITS: Nonresulphurized Carbon Steels AISI No. 1008 1010 1012 1015 1016 1017 1018 1019 1020 1021 1022 1023 1024 10 1026 1027 1029 10 1035 1036 1037 1038 1039 10 1041 1042 1043
CALCULATION & DRAFTING STANDARDS MANUAL PROCEDURE: C&D 515 Bill of Materials Standard REV 0.0 5/6/04
BROWN MINNEAPOLIS TANK PAGE 1 OF 7 PURPOSE: Create and Drawing Uniformity Create, explain, and establish a standard bill of materials to be placed on every drawing (except the overall tank elevation and
Africa s leading steel supplier CATALOGUE TUBE & PIPE. The Macsteel Group - Africa s leading steel supplier - www.macsteel.co.za
Africa s leading steel supplier CATALOGUE TUBE & PIPE - www.macsteel.co.za TUBE & PIPE CONTENTS 1. Contents 13. Conveyance SANS 1182 - Light Page 7 2. Contact Details 14. Conveyance SANS 719 - Large Bore
North American Stainless Long Products
North American Stainless Long Products 1 North American Stainless North American Stainless is part of the most competitive stainless steel manufacturing group in the world, Acerinox, S.A. The development
There is no upside to. down time
EXPANDED and PERFORATED Data and Specifications 30 Similar to Type 302 with excellent mechanical properties, resistance to many corrosive agents. Useful where sanitation and cleanliness are important.
GUARDRAIL POST STEEL
GUARDRAIL POST STEEL Guardrail posts meeting materials certification are evaluated and checked for: 1. Dimensional acceptance 2. Physical test results a. Chemical b. Physical 3. Galvanized or painted coating
Wear-resistant steels. Technical terms of delivery for heavy plates. voestalpine Grobblech GmbH www.voestalpine.com/grobblech
Wear-resistant steels Technical terms of delivery for heavy plates voestalpine Grobblech GmbH www.voestalpine.com/grobblech Wear-resistant steels durostat durostat 400 durostat 450 durostat 500 durostat
ASTM A860/A860M-09 Standard Specification for Wrought High Strength. Ferritic Steel Butt Welding Fittings. 1. Scope :- 2. Reference Documents :-
Standard Specification for Wrought High Strength Ferritic Steel Butt Welding Fittings 1. Scope :- 1.1 This specification covers wrought high strength ferritic steel butt-welding fitting of seamless and
The Keep It Simple, Steel (KISS) Standard
The Keep It Simple, Steel (KISS) Standard A standard Electronic Data Interchange (EDI) format for the exchange of Bill of Material (BOM) information within the steel fabrication industry Updated in March
Alternative Steel Materials to BS 5950
BC 1: 2008 Design Guide on Use of Alternative Steel Materials to BS 5950 BCA Sustainable Construction Series 3 The education and research arm of the Building and Construction Authority 200 Braddell Road
SECTION 15076 CEMENT-MORTAR LINED AND COATED STEEL PIPE
SECTION 15076 CEMENT-MORTAR LINED AND COATED (CML&C) STEEL PIPE PART 1 GENERAL 1.01 DESCRIPTION This section designates the requirements for steel pipe fabrication, test in shop, installation of steel
AISI O1 Cold work tool steel
T OOL STEEL FACTS AISI O1 Cold work tool steel Great Tooling Starts Here! This information is based on our present state of knowledge and is intended to provide general notes on our products and their
Flash Butt Welding Machines
Flash Butt Welding Machines Types AS 15 - AS 320 Flash butt welding current brake current (ka) current time flattening reversal preheating welding time flash butting forging A reliable and economic process
Caps STANDARD WEIGHT Inches / Pounds
Standard Caps you are here: Home > Weldbend Catalog > Fittings > Caps Caps STANDARD WEIGHT Inches / Pounds For Metric Units >Click Here Nominal Pipe Size Outside Inside Wall Thickness (T) Length (E) Pipe
LEGACY REPORT ER-5110. www.icc-es.org. ICC Evaluation Service, Inc. Reissued November 1, 2003. Legacy report on the 1997 Uniform Building Code
LEGACY REPORT Reissued November 1, 2003 ICC Evaluation Service, Inc. www.icc-es.org Business/Regional Office # 5360 Workman Mill Road, Whittier, California 90601 # (562) 699-0543 Regional Office # 900
North American Stainless
North American Stainless Long Products Stainless Steel Grade Sheet 2205 UNS S2205 EN 1.4462 2304 UNS S2304 EN 1.4362 INTRODUCTION Types 2205 and 2304 are duplex stainless steel grades with a microstructure,
Profiles in stock Standard catalogue. Discover the possibilities with aluminium profiles from Sapa
Profiles in stock Standard catalogue Discover the possibilities with aluminium from Sapa You can create your own profile or you can choose from a wide selection of standard. Delivery: 1 2 weeks for standard
Residential Deck Safety, Construction, and Repair
Juneau Permit Center, 4 th Floor Marine View Center, (907)586-0770 This handout is designed to help you build your deck to comply with the 2006 International Residential Building code as modified by the
Stock & Reference Guide
Stock & Reference Guide Stock & Reference Guide Boyd Metals of Fort Smith 600 South 7th Street P.O. Bo 89 Fort Smith, rkansas 72902089 (479) 7829060 Fa (479) 7823980 Fa (479) 7820424 (800) 3238806 Boyd
Standard Specification for Stainless Steel Bars and Shapes 1
Designation: A 276 06 Standard Specification for Stainless Steel Bars and Shapes 1 This standard is issued under the fixed designation A 276; the number immediately following the designation indicates
CT-02 CABLE TRAY SYSTEMS
CT-02 CABLE TRAY SYSTEMS SYSTEMS THAT MAKE SENSE Introduction B-Line Systems was formed in 96 and has over 30 years experience manufacturing cable tray systems in which it has grown to become the industry
SPECIFICATIONS FOR STEEL PIPE
SPECIFICATIONS FOR STEEL PIPE Published pipe standards serve three functions. 1. They dictate manufacturing and testing requirements and prescribed methods of measuring the required mechanical and physical
TABLE OF CONTENTS 2 Heavy-Wall Seamless & Welded Carbon Steel Pipe. 4 Alloy Pipe & Tube. 6 Chrome-Moly Pipe. 7 Low-Temp Pipe
PRODUCT CATALOG TABLE OF CONTENTS 2 Heavy-Wall Seamless & Welded Carbon Steel Pipe 4 Alloy Pipe & Tube 6 Chrome-Moly Pipe 7 Low-Temp Pipe 9 Services amerpipe.com 1.800.316.5737 [email protected] 18333
1.02 SYSTEM DESCRIPTION
1 OF 7 MODULAR MEZZANINES GUIDE SPECIFICATIONS FOR PART 1 - GENERAL 1.01 RELATED WORK A. SECTION 03 30 00: Cast in Place Concrete (and Concrete Finishing) 1. The area where mezzanine is installed shall
Lecture slides on rolling By: Dr H N Dhakal Lecturer in Mechanical and Marine Engineering, School of Engineering, University of Plymouth
Lecture slides on rolling By: Dr H N Dhakal Lecturer in Mechanical and Marine Engineering, School of Engineering, University of Plymouth Bulk deformation forming (rolling) Rolling is the process of reducing
ALLOY 2205 DATA SHEET
ALLOY 2205 DATA SHEET UNS S32205, EN 1.4462 / UNS S31803 GENERAL PROPERTIES ////////////////////////////////////////////////////// //// 2205 (UNS designations S32205 / S31803) is a 22 % chromium, 3 % molybdenum,
60.12. Depend-O-Lok FxE Expansion Coupling. System No. Submitted By Spec Sect Para Location Date Approved Date. DEPEND-O-LOK FxE EXPANSION COUPLING
60.1 D-O-L FxE expansion couplings are a bolted, split-sleeve design that provides for expansion and contraction at the coupled joint. These couplings are furnished with restraint rings that, when affixed
STANDARD REQUIREMENTS FOR BONDING OR MECHANICAL ATTACHMENT OF INSULATION PANELS AND MECHANICAL ATTACHMENT OF ANCHOR AND/OR BASE SHEETS TO SUBSTRATES
ROOFING APPLICATION STANDARD (RAS) No. 117 STANDARD REQUIREMENTS FOR BONDING OR MECHANICAL ATTACHMENT OF INSULATION PANELS AND MECHANICAL ATTACHMENT OF ANCHOR AND/OR BASE SHEETS TO SUBSTRATES Scope 1.1.
Sports and High Mast Lighting Poles Phone: (866) 474-7200 Fax: (817) 924-7049
Sports and High Mast Lighting Poles 4 High Mast Lighting Poles General American LitePole offers a raising and lowering system that allows for ease of maintaining the lighting system at ground level. Ideal
Welded Fabric. The CARES Guide to Reinforcing Steels Part 5. Installation of welded fabric on a major contract. 1.0 Introduction
Welded Fabric 1.0 Introduction Welded fabric, often referred to as mesh, is a machine welded grid arrangement of reinforcing bars or wires. It is covered by British Standard BS4483. This was revised in
MATERIALS AND MECHANICS OF BENDING
HAPTER Reinforced oncrete Design Fifth Edition MATERIALS AND MEHANIS OF BENDING A. J. lark School of Engineering Department of ivil and Environmental Engineering Part I oncrete Design and Analysis b FALL
JIS G3472 Electric Resistance Welded Carbon Steel Tubes for Automobile Structural Purposes
JIS G3472 Electric Resistance Welded Carbon Steel Tubes for Automobile Structural Purposes 1. Scope This Japanese Industrial Standard specifies the electric resistance welded carbon steel tubes, hereinafter
Specification for Rotary Drill Stem Elements
Addendum 1 March 2007 Effective Date: September 1, 2007 Specification for Rotary Drill Stem Elements ANSI/API SPECIFICATION 7-1 FIRST EDITION, MARCH 2006 EFFECTIVE DATE: SEPTEMBER 2006 ISO 10424-1:2004
Specifications, Product Testing and Terminology
Specifications, Product Testing and Terminology The following synopsis provides a review of various material and final product testing, which is performed on our products, as well as, many of our competitors.
Fabcograte FRP Grating. Tolerances: ±1/16. Tolerances: ±1/16. THICKNESS BAR SPACING PANEL SIZE (FT.) WT (LBS) 1" 1.5" x 1.
Features: Will not rust. Corrosion resistant. Non-sparking. Fire retardant. Non-conductive. Maintenance free. Molded-in color. Light weight. Easy to install. Impact resistant. Quality appearance. Fabcograte
GENERAL PROPERTIES //////////////////////////////////////////////////////
ALLOY 625 DATA SHEET //// Alloy 625 (UNS designation N06625) is a nickel-chromium-molybdenum alloy possessing excellent resistance to oxidation and corrosion over a broad range of corrosive conditions,
Stainless steel grade chart
Stainless steel grade chart ATLAS STEELS METAL DISTRIBUTION Chemical analysis (%) specified C Si Mn P S Cr Mo Ni Other Austenitic stainless steels 253MA S30815 0.05 1.1-2.0 0.8 0.040 0.030 20.0-22.0 10.0-12.0
JANUARY 1, 2015 AVAILABILITY LIST
JANUARY 1, 2015 AVAILABILITY LIST EXTREN Structural Shapes and Plate...2 Special Composite Shapes...4 DURADEK and DURAGRID Pultruded Grating...6 DURAGRATE Molded Grating...8 DURATREAD TM Molded Stair Tread
DSM http://www.dsmmfg.com 1 (800) 886-6376
DESIGN GUIDE FOR BENT SHEET METAL This guide discusses how the bends are made, what thicknesses of sheet metal are commonly used, recommended bend radius to use when modeling the part, some practical limits
Detailing of Reinforcment in Concrete Structures
Chapter 8 Detailing of Reinforcment in Concrete Structures 8.1 Scope Provisions of Sec. 8.1 and 8.2 of Chapter 8 shall apply for detailing of reinforcement in reinforced concrete members, in general. For
5 G R A TINGS ENGINEERING DESIGN MANUAL. MBG Metal Bar Grating METAL BAR GRATING MANUAL MBG 534-12 METAL BAR GRATING NAAMM
METAL BAR NAAMM GRATNG MANUAL MBG 534-12 5 G R A TNG NAAMM MBG 534-12 November 4, 2012 METAL BAR GRATNG ENGNEERNG DEGN MANUAL NAAMM MBG 534-12 November 4, 2012 5 G R A TNG MBG Metal Bar Grating A Division
DESCRIPTION. Stud Bolts for Pressure-Temperature Piping 2-1. General Purpose End-to-End Studs 2-2. Tap End Stud Bolts 2-3. Double End Stud Bolts 2-4
DESCRIPTION PAGE B7 Studs and Nuts Stud Bolts for Pressure-Temperature Piping 2-1 General Purpose End-to-End Studs 2-2 Tap End Stud Bolts 2-3 Double End Stud Bolts 2-4 Sigma Fasteners, Inc. Section 2 STUD
TECHNICAL SPECIFICATION SERIES 8000 PRECAST CONCRETE
TECHNICAL SPECIFICATION SERIES 8000 PRECAST CONCRETE TECHNICAL SPECIFICATION PART 8000 - PRECAST CONCRETE TABLE OF CONTENTS Item Number Page 8100 PRECAST CONCRETE CONSTRUCTION - GENERAL 8-3 8101 General
Wear-resistant steel grades. Hot-rolled steel strip and heavy plate. voestalpine Steel Division www.voestalpine.com/steel
Wear-resistant steel grades Hot-rolled steel strip and heavy plate Josef Elmer, Key Account Manager voestalpine Steel Division www.voestalpine.com/steel For the highest stress Highest resistance to wear
Mechanical arms, belts and sheets
Car parks Mechanical arms, belts and sheets DETAIL ARM CAR PARK (mm) 5000 Platen 100x5mm Iron sheets 4mm 5000 485 2100 Belts type C 120x50x2 mm 4915 5400 Hot dipped galvanized UNE-EN ISO 1461 or black
Copper-Nickel Mill Products
Copper-Nickel Mill Products Copper-Nickel Rod, Sheet, Plate, and Tubing ALASKAN COPPER & BRASS COMPANY History W hen Alaskan Copper Works was founded as a marine coppersmithing company in 9, one of its
JIS G3445 Carbon steel tubes for machine structural purposes
JIS G3445 arbon steel tubes for machine structural purposes 1. Scope This Japanese Industrial Standard specifies the carbon steel tubes, hereinafter referred to as the "tubes", used for machinery, automobiles,
Vrtné trubky Drill Pipe
Vrtné trubky Drill Pipe VRTNÉ ROURY - zušlechtěné závity - vysoká kvalita těla roury - svařeno třením - vysoká přímost vrtných tyčí - závity dle STN, API, DIN a GOST - délky dle přání zákazníka Průměr
Materials. Estimating Steel. Players. Materials. Shop Drawings. Detailing Process. Standard shapes. Fabricated members, Built-up sections
Materials Standard shapes W sections, C channels, Structural T, Angles, Pipes, Tubes, Rods and Plates Fabricated members, Built-up sections Adding plates to beam flanges, Stiffeners to beam webs Built
HIGH STRENGTH SHEET AND PLATE STEELS FOR OPTIMUM STRUCTURAL PERFORMANCE
HIGH STRENGTH SHEET AND PLATE STEELS FOR OPTIMUM STRUCTURAL PERFORMANCE Jan-Olof Sperle SSAB Tunnplåt AB, Borlänge, Sweden SUMMARY Modern quench and tempering as well as continuous annealing make it possible
DENVER MODEL 30 X 30 SPECIFICATIONS
DENVER MODEL 30 X 30 SPECIFICATIONS Dimensions: Roof Dimensions 30-0 x 30-0 (4) Columns (Center to Center) 25-6½ x 25-6½ Minimum Clearance 8-0 Roof Height @ Peak Dependent on Col. Ht. Hip Roof 4:12 pitch
Synergy THE O NEAL FAMILY OF COMPANIES
Synergy Family is synonymous with synergy at O Neal Industries (ONI). As part of the nation s largest family-owned group of metals service centers, each ONI company and each individual operation have the
It's large enough to handle most welding job shop projects, yet small enough to make it a worth while home-workshop tool
It's large enough to handle most welding job shop projects, yet small enough to make it a worth while home-workshop tool H Craft Print Project No. 272 ERE'S a metal bender that will enable you to bend
GUARDRAIL INNOVATION FLOWS FROM HERE
INNOVATION FLOWS FROM HERE ENSURING SAFETY ON CANADIAN HIGHWAYS The economics, versatility, and performance of Guardrail surpass all other roadside barrier systems. Guardrail provides highly-visible protection
SECTION 1 GENERAL REQUIREMENTS
Page 1 of 6 SECTION 1 GENERAL REQUIREMENTS 1. SCOPE OF WORK: The work to be performed under the provisions of these documents and the contract based thereon includes furnishing all labor, equipment, materials,
High-strength and ultrahigh-strength. Cut sheet from hot-rolled steel strip and heavy plate. voestalpine Steel Division www.voestalpine.
High-strength and ultrahigh-strength TM steels Cut sheet from hot-rolled steel strip and heavy plate Josef Elmer, Key account manager voestalpine Steel Division www.voestalpine.com/steel Weight savings
Hamilton Form Company, Ltd Custom Designs, Flexible Solutions
Hamilton Form Company, Ltd Custom Designs, Flexible Solutions 1 IFC 2 CUSTOM DESIGNS, FLEXIBLE SOLUTIONS Hamilton Form has been designing and building custom steel forms for the precast industry since
Section 4: NiResist Iron
Section 4: NiResist Iron Section 4 Ni-Resist Description of Grades...4-2 201 (Type 1) Ni-Resist...4-3 202 (Type 2) Ni-Resist...4-6 Stock Listings...4-8 4-1 Ni-Resist Description of Grades Ni-Resist Dura-Bar
Section 2100-Trenching and Tunneling
SECTION 5200 - STORM SEWER PART 1 - GENERAL 1.01 SCOPE: This Section covers installation of storm sewer mains and culverts. Topics include permits and fees, trench widths, pipe laying, bedding, initial
Seamless stainless tubes for hydraulic and instrumentation systems
Seamless stainless tubes for hydraulic and instrumentation systems stock assortment integrated production technical knowledge network of sales and service Reduce your lifecycle costs When selecting tubes
MEZZANINE SPECIFICATIONS PART 1 GENERAL 1.1 SCOPE 1.2 APPROVED MANUFACTURER 1.3 REGULATORY ORGANIZATIONS AND GROUPS 1.4 QUALITY ASSURANCE
MEZZANINE SPECIFICATIONS PART 1 GENERAL 1.1 SCOPE This specification is intended to describe the general requirements applicable to a proper structural mezzanine design. In addition, it is to serve as
Safety Grating GSSG-13R GRIP STRUT. safety grating
Safety Grating GSSG-13R safety grating Table of Contents & Advantages Advantages.................................................... 2 Proof Of Performance...................................... 3 General
Flanged and Butt-= Weld Type
Document : PG00 Year : 09 Product Group 00 Flanged and Butt-= Weld Type (LNG and LPG) Page 09 Document : PG00 Year : 09 Product Group 00 Cryogenic Butterfly valves The Cryogenic Butterfly Valve Design
Valu Guide Sheaths. Valu Guide Inserts. Optional Valu Guide Inserts. Typical Properties of Valu Guide Rail. and Hardware.
14 gauge stainless steel The Original, Long Life Sanitary Guide Rail Valu Guide rail incorporates two outstanding materials: stainless steel and UHMW. The 14 ga. stainless steel sheath provides rigid streamlined
HIGH TENSION CABLE BARRIER
Special Provision September 11, 2006 SECTION 02845 S HIGH TENSION CABLE BARRIER PART 1 GENERAL 1.1 SECTION INCLUDES A. Cable barrier materials and installation procedures. 1.2 RELATED SECTIONS A. Section
Product Catalogue (updated Feb. 2010)
Product Catalogue (updated Feb. 2010) 315 BROCK RD GREENSVILLE ON L9H 5H7 PHONE: 905-628-0766 FAX: 905-628-8277 www.efcomltd.com [email protected] 1 Table of Contents Tool Boxes... 3 Cylinder Enclosures
Pipe threads for tubes and fittings where pressure-tight joints are not made on the threads. (requires PTFE sealing tape or liquid sealant).
Fittings for CO 2 Pipe Threads Pipe thread references quoted in this catalogue conform with the requirements specified in the latest issue and amendments of the following ISO Standards: ISO 7-1 (BS21)
Tolerance +/- 0,5 mm, +/- 0,2 mm. Length 15-350 mm ( standard) SLOTS. 9 5/8 x 36 Ibs/ft. 4 1/2 x 9,5 Ibs/ft. Slotted casing
Slotted casing Tube API 5CT, grade J/K55, R1, R2, STC: 4 1/2 x 9,5 Ibs/ft number of slots / meter number of ranges on circumference number of ranges per linear meter 24 4 6 9 5/8 x 36 Ibs/ft 48 8 6 Slotted
COLORADO MODEL. 35 x 65 SPECIFICATIONS
COLORADO MODEL 35 x 65 SPECIFICATIONS Dimensions: Roof Dimensions 35-0 x 65-0 Column Dimensions (center to center) 31-0 x 30-6 Minimum Clearance 14-0 Roof Height @ Peak ±18-8 Curved Roof ±42-6 radius Square
PRELIMINARY BROCHURE. Uddeholm Ramax HH
PRELIMINARY BROCHURE Uddeholm Ramax HH Uddeholm Ramax HH Uddeholm Ramax HH provides several benefits: The product offers uniform hardness in all dimensions combined with excellent indentation resistance.
RAMAX S Prehardened stainless holder steel
T O O L S T E E L F A C T S RAMAX S Prehardened stainless holder steel Wherever tools are made Wherever tools are used This information is based on our present state of knowledge and is intended to provide
Structural Bolting. Notice the Grade 5 has a much smaller head configuration and a shorter shank then the A325 structural bolt. Rev.
Structural Bolting ASTM A325 and ASTM A490 are the two U.S. standard structural bolts. When looking at the mechanical requirements of bolts it appears that an ASTM A325 and SAE J429 Grade 5 are identical
SUPPLEMENTAL TECHNICAL SPECIFICATIONS BI-DIRECTIONAL STATIC LOAD TESTING OF DRILLED SHAFTS
July 14, 2015 1.0 GENERAL BI-DIRECTIONAL STATIC LOAD TESTING OF DRILLED SHAFTS This work shall consist of furnishing all materials, equipment, labor, and incidentals necessary for conducting bi-directional
North American Stainless
North American Stainless Flat Products Stainless Steel Grade Sheet 310S (S31008)/ EN 1.4845 Introduction: SS310 is a highly alloyed austenitic stainless steel designed for elevated-temperature service.
External Wrapping of Steel Riser Pipe. Case Study HJ3 CS200902
External Wrapping of Steel Riser Pipe Case Study HJ3 CS200902 Introduction Refineries process a wide variety of petroleum products. As part of the process, they rely on cooling towers, which recycle water
Dock Hardware & Accessory Products Catalog
Dock Hardware & Accessory Products Catalog Product Page # Product Page # Angle Brackets/Clips 8 Back Up Plate 5 Backing Plate/Hurricane Stop 10 Carriage Bolt Sets 4 Chain Retainer 10 Connector Pin Set
TS 813 GROUNDING AND BONDING TTD 813.001 TRAFFIC SIGNAL INSTALLATION AND CONTROLLER CABINET GROUNDING SYSTEM TTD 813.005 CONTROLLER CABINET GROUNDING
TORONTO TRANSPORTATION January 2012 TS 813 GROUNDING AND BONDING TABLE OF CONTENTS 1. DRAWINGS TTD 813.001 TRAFFIC SIGNAL INSTALLATION AND CONTROLLER CABINET GROUNDING SYSTEM TTD 813.005 CONTROLLER CABINET
IKG Bar Grating: Anchoring
IKG Bar Grating: Anchoring All bar grating must be tightly fastened in place. Welding of the grating panels to the supporting members provides a superior, permanent installation. Although, for gratings
STAVAX SUPREME. Stainless tool steel
STAVAX SUPREME Stainless tool steel General Demands placed on plastic mould tooling are increasing. Such conditions require mould steels that possess a unique combination of toughness, corrosion resistance
AUSTENITIC STAINLESS DAMASCENE STEEL
AUSTENITIC STAINLESS DAMASCENE STEEL Damasteel s austenitic stainless Damascene Steel is a mix between types 304L and 316L stainless steels which are variations of the 18 percent chromium 8 percent nickel
The following sketches show the plans of the two cases of one-way slabs. The spanning direction in each case is shown by the double headed arrow.
9.2 One-way Slabs This section covers the following topics. Introduction Analysis and Design 9.2.1 Introduction Slabs are an important structural component where prestressing is applied. With increase
FY11 Sanitary Sewer Main Rehab and Point Repair Bid Tabulation
644-10-569 Page 1 of 9 1 FOR CLEANING AND TELEVISING EXISTING SEWERS, AS SPECIFIED, ANY REQUIRED CLEANING, ANY LOCATION, ANY LENGTH OF SEWER, COMPLETE IN PLACE, FOR VARIOUS PIPE DIAMETERS. A. EXISTING
ROLL PASS DESIGN EVAULUATION USING SOFTWARE APPLICATION ARINDAM MUKHERJEE PROJECT MANAGEMENT CELL UNDP/GEF PROJECT (STEEL)
ROLL PASS DESIGN EVAULUATION USING SOFTWARE APPLICATION ARINDAM MUKHERJEE PROJECT MANAGEMENT CELL UNDP/GEF PROJECT (STEEL) OBJECTIVE OF ROLL PASS DESIGN Steel sections are generally rolled in several passes,
Activity 2.3b Engineering Problem Solving Answer Key
Activity.3b Engineering roblem Solving Answer Key 1. A force of 00 lbs pushes against a rectangular plate that is 1 ft. by ft. Determine the lb lb pressure in and that the plate exerts on the ground due
4 X 1 3/8 X 3/16 CHANNEL 101.6 x 34.9 x 4.8 CHANNEL
4 X 1 3/8 X 3/16 CHANNEL 101.6 x 34.9 x 4.8 CHANNEL ALLOWABLE UNIFORM LOADS (lbs./ft. / N/m.) Laterally Supported A w = 0.680 in. 2 / 438.7mm 2 Wt. = 0.88 lbs./ft. / 1.31kg/m. I = 2.62 in. 4 / 1090526mm.
Working Drawing and Assemblies. Chapter 10
Working Drawing and Assemblies Chapter 10 Objectives 1.Define working drawings. 2. Describe how working drawings are used in industry. 3. List the major components of a complete set of working drawings.
Contents Nickel Alloys... 2 Copper Alloys... 19 Titanium Alloys... 26 Stainless Steel... 33 Miscellaneous... 35 Welding Material... 37 Contact...
2015-04-09 Page 1 Contents Nickel Alloys... 2 Copper Alloys... 19 Titanium Alloys... 26 Stainless Steel... 33 Miscellaneous... 35 Welding Material... 37 Contact... 41 2015-04-09 Page 2 Nickel Alloys Alloy
Formwork Direct International Ltd Phone No +44 (0151) 532 0179 Fax no +44 (0151) 523 8330 E-Mail: [email protected].
Tie Rod & Formwork s well as containing our comprehensive range of Formwork Tie Sytems; this section also covers our market leading Rapidobat Column Former. Exclusive also to Formwork Direct are innovations
ATLANTA MODEL SPECIFICATIONS
ATLANTA MODEL 50 SPECIFICATIONS Dimensions: Roof Dimensions (point to point) 50-0 Column Dimensions (out to out of columns) 44-0 Eave Height 8-0 Roof Height @ Peak ±21-8⅞ Hip Roof 6:12 pitch Square Feet
1 Barlines Rebar Detailing Standards in the Philippines
Barlines Rebar Detailing Standards in the Philippines METRIC (SI), STANDARD HOOKS AND OTHER DETAILING CRITERIAS By Amadeus (Mady) Magpile, President and CEO INTRODUCTION This is first in a series of articles
HOTCHKISS AIR SUPPLY Heating, Ventilating & Air Movement Equipment
HOTCHKISS AIR SUPPLY Heating, Ventilating & Air Movement Equipment F l a t O v a l T u b e a n d F i t t i n g s Introduction Hotchkiss Flat Oval ductwork offers all the advantages of rectangular ducts
Rev. 00 S-7016.H. COVERED ARC WELDING ELECTRODE FOR 490MPa CLASS HIGH TENSILE STEEL HYUNDAI WELDING CO., LTD.
Rev. 00 COVERED ARC WELDING ELECTRODE FOR 490MPa CLASS HIGH TENSILE STEEL HYUNDAI WELDING CO., LTD. Specification AWS JIS EN ISO Z3211 A5.1 2560-A E7016 E4916 E42 E4916 E42 3 B 1 2 Applications Structures
Anodes and Misc Equipment
Anodes and Misc Equipment Application: Platinised Titanium Anodes Platinised titanium anodes are recommended for use in the following electrolytic processes:- Precious metal electroplating - e.g. Au, Pt,
Technical Notes 3B - Brick Masonry Section Properties May 1993
Technical Notes 3B - Brick Masonry Section Properties May 1993 Abstract: This Technical Notes is a design aid for the Building Code Requirements for Masonry Structures (ACI 530/ASCE 5/TMS 402-92) and Specifications
High-Strength Low-Alloy Steels
High-Strength Low-Alloy Steels Introduction and Overview High-strength low-alloy (HSLA) steels, or microalloyed steels, are designed to provide better mechanical properties and/or greater resistance to
Pole Data Sheets (CDN) INFRASTRUCTURE FOR LIFE
Data Sheets (CDN) INFRASTRUCTURE FOR LIFE RS Technologies www.rstandard.com Email Toll Free Phone Fax [email protected] +1 877 219 8002 +1 403 219 8000 +1 403 219 8001 2421 37th Avenue NE, Suite 400 Calgary,