Printing recorder with text printing and 24-character LED dot-matrix display. Brief description. Overview of functions. Features of the Type

Transcription

1 JUMO GmbH & Co. KG Delivery address:mackenrodtstraße 14, Fulda, Germany Postal address: Fulda, Germany Phone: Fax: Internet: JUMO Instrument Co. Ltd. JUMO House Temple Bank, Riverway Harlow, Essex CM20 2DY, UK Phone: Fax: Internet: JUMO Process Control, Inc. 8 Technology Boulevard Canastota, NY 13031, USA Phone: JUMO JUMO Fax: info@jumo.us Internet: Data Sheet Page 1/12 Printing recorder with text printing and 24-character LED dot-matrix display Brief description The LOGOPRINT recorder family consists of two printing recorders, the LOGOPRINT 500 and the LOGOPRINT 500 junior. LOGOPRINT 500 () The printing recorder is equipped with 3 or (optionally) 6 measurement inputs, which are electrically isolated from one another. The evaluation of the measurement traces of the printing recorder can be assisted by extensive text printing. The recorder can be programmed either by using the 8 keys on the front of the instrument or through a PC setup program. Thermocouples, resistance thermometers, resistance transmitters, potentiometers, voltages or currents (standard signals) are possible as input signals. The appropriate linearizations are carried out automatically, but can also be adapted to customer-specific linearizations with the help of the PC setup program. Further outstanding features of the LOGOPRINT 500, which are already included in the basic version, are four open-collector outputs for signaling infringements of limits and faults, eight event traces, as well as peak value recording. The color assignments (measurement traces and texts) are freely programmable via the PC setup program, which is available as an accessory. LOGOPRINT 500 junior (Type ) This recorder is equipped with 6 measurement inputs, which are electrically isolated from one another. It can also support the evaluation of the measurement traces with printed text (limited). Programming is only possible via the keys. Voltages and currents (standard signals) are possible as input signals. There are no open-collector outputs, no event traces, no peak value recording and no extra codes. Overview of functions Analog inputs (configurable and isolated) Type or 6 inputs for: - thermocouples - resistance thermometers - resistance transmitters - potentiometers - voltage and current 6 inputs for: - voltage - current 8 logic inputs available as extra code not available Outputs - 4 open-collector outputs available as extra code: - interface for 8 relay outputs - supply for 2-wire transmitter not available Recording Setup interface RS422/RS485 interface - measurement traces - text printing - event traces for configuration and parameter setting via PC extra code for the data transfer from and to the recorder Supply voltage V AC +10/-15% 48 63Hz V AC/DC ±0% 48 63Hz - measurement traces - text printing (limited) not available not available V AC +10/-15% 48 63Hz V AC/DC ±0% 48 63Hz Features of the k Limit monitoring k Event traces k Four open-collector outputs k Peak value recording k Extensive text printing k Statistics (report) with minimum, maximum and mean values k Event- and time-controlled chart speed k Math and logic module (PC setup program is required) k Universal chart cassette Approvals Type

2 JUMO GmbH & Co. KG Fulda, Germany Data Sheet Page 2/12 Technical data Thermocouple input () Designation Range Linearisation accuracy 1 Fe-Con L DIN Fe-Con J EN Cu-Con U DIN Cu-Con T EN NiCr-Ni K EN NiCr-Con E EN NiCrSi-NiSi N EN Pt10Rh-Pt S EN Pt13Rh-Pt R EN Pt30Rh-Pt6Rh B EN to C -210 to C -200 to C -270 to C -270 to C -270 to C -270 to C -50 to C -50 to C C Shortest span Types L, J, U, T, K, E, N: Types S, R, B: Range start/end Cold junction ±0.2% ±0.2% above -200 C ±0.3% ±0.5% above -200 C ±0.2% above -150 C ±0.2% above -200 C ±0.2% above -150 C ±0.5% above 0 C ±0.5% above 0 C ±0.5% above 500 C 100 C 500 C freely programmable within the limits in 0.1 C steps Pt 100 internal or thermostat as external constant Cold junction accuracy (internal) ± 1 C Cold junction temperature (external) Measurement time Input filter Features -50 to +100 C, adjustable through setup software for 3 channels < 2sec; for 6 channels < 4sec 2nd order digital filter; filter constant adjustable from sec also programmable in F; customer-specific linearizations 1 The linearization accuracy refers to the maximum span. The linearization accuracy is reduced for shorter spans. 2 invalid DIN since 1995 Resistance thermometer input () Pt 100 EN Pt 100 JIS Pt 500 DIN Pt 1000 DIN Ni 100 Connection type Connection Range Linearisation accuracy Meas. current -200 to +250 C -200 to +850 C -200 to +250 C -200 to +850 C -200 to +260 C -200 to +649 C -200 to +260 C -200 to +649 C -200 to +150 C -200 to +850 C -200 to +150 C -200 to +850 C -200 to +250 C -200 to +850 C -200 to +250 C -200 to +850 C -60 to +125 C -60 to +180 C -60 to +125 C -60 to +180 C ±0.6 C ±1.0 C ±0.5 C ±0.8 C ±0.6 C ±1.0 C ±0.5 C ±0.8 C ±0.6 C ±1.0 C ±0.5 C ±0.8 C ±0.6 C ±1.0 C ±0.5 C ±0.8 C ±0.6 C ±1.0 C ±0.5 C ±0.8 C 2-, 3- or circuit Shortest span 15 C Probe lead resistance Range start/end Measurement time Input filter Features max. 30 Ω per core for circuit max. 20Ω per core for 2- and 3-wire circuit for Pt 100 up to 260 C max. 10 Ω per core in 2-wire and 3-wire circuit freely programmable within the limits in 0.1 C steps for 3 channels < 2sec; for 6 channels < 4sec 2nd order digital filter; filter constant adjustable from 0 50sec also programmable in F; customer-specific linearizations

3 JUMO GmbH & Co. KG Fulda, Germany Data Sheet Page 3/12 Resistance transmitter and potentiometer input () Range Accuracy Measuring current up to 200Ω up to 400Ω up to 800Ω up to 2000Ω up to 4000Ω Connection type Shortest span Probe lead resistance Resistance values Measurement time Input filter Input for DC voltage or DC current ( and Type ) Basic range Accuracy Input resistance -25 to +75mV 0 100mV -100 to +100mV 0 200mV -500 to +500mV 0 1V -1 to +1V -5 to +5V 0 10V -10 to +10V Shortest span Range start/end 4 20mA 0 20mA -20 to +20mA Shortest span Range start/end Measurement time Input filter Features Transducer short-circuit/break ±300mΩ ±600mΩ ±1Ω ±2Ω ±3Ω ±100μV ±100μV ±150μV ±150μV ±1mV ±1mV ±2mV ±10mV ±10mV ±15mV ±20μA ±20μA ±40μA resistance transmitter: 3-wire circuit potentiometer: 2-, 3- or circuit 6Ω max. 30Ω per core in circuit max. 20Ω per core in 2-and 3-wire circuit up to 200 Ω range: max. 10 Ω per core in 2-and 3-wire circuit freely programmable within the limits in 0.1Ω steps for 3 channels < 2sec; for 6 channels < 4sec 2nd order digital filter; filter constant adjustable from sec R E > 0.5 MΩ R E > 0.5 MΩ R E > 0.5 MΩ 5mV freely programmable within the limits (up to 999mV in 0.01mV steps, from 1V in 1mV steps) burden voltage 2.6V max. burden voltage 2.6Vmax. burden voltage 2.6Vmax. 0.5mA freely programmable within the limits in 0.1mA steps for 3 channels < 2sec; for 6 channels < 4sec 2nd order digital filter; filter constant adjustable from sec for : adjustable linearizations for thermocouples and resistance thermometers (for connection to transmitters without linearization) Short-circuit 1 Break 1 Thermocouple not recognized recognized Resistance thermometer recognized recognized 2 Resistance transmitter recognized recognized Potentiometer not recognized recognized 2 Voltage up to ± 1V not recognized recognized Voltage above ± 1V not recognized not recognized Current not recognized not recognized 1 The print head is positioned to 0%, >>>>>> appears in the LED dot-matrix display. 2 In circuit: only recognized at terminals 1 and 2. Outputs () Three open-collector outputs One open-collector output Printing system ( and Type ) Drive Sensitivity Reproducibility Display and recording accuracy to signal over/underlimit to signal faults (e. g. end of chart) stepper motor 0.2% or better referred to 100mm writing width 0.25% or better referred to 100mm writing width Class 0.5 referred to range limits and basic ranges

4 JUMO GmbH & Co. KG Fulda, Germany Data Sheet Page 4/12 Print head Print colors Over/underrun Chart speed Paper feed Chart cassette Chart overall width / writing width sprocket roller spacing visible diagram length overall length print head with penlift function - sufficient for approx. 1 million dots (depending on the ambient temperature) Violet, red, black for 3-channel printing recorder and violet, red, black, green, blue, brown for 6-channel printing recorder. For the color assignment can be changed at will, through the setup program. electronically limited to 0 100mm writing width programmable in the steps 0, 5, 10, 20, 60, 120, 240, 300, 360, 600, 720mm/h by stepper motor and gearing cassette for roll chart and fanfold chart (with tear-off edge and paper-end switch) roll or fanfold chart to DIN mm / 100mm 110mm roll chart: 60mm; fanfold chart: 30 60mm roll chart: 16m or 32m; fanfold chart: 16m Electrical data ( and Type ) Supply (SMPS) V AC +10/-15% AC 48 63Hz, or 20 53V ±0% AC/DC 48 63Hz Electrical safety to EN , Part 1, March 1994 overvoltage Category II, contamination Grade 2 Test voltages (type test) mains supply to measurement circuit with AC supply 2.3kV 50Hz, 1min; with AC/DC 510V 50Hz, 1min mains supply to housing with AC supply 1.5kV 50Hz, 1min; with AC/DC 510V 50Hz, 1min between measurement circuits 200V 50Hz, 1min measurement circuits to housing 500V 50Hz, 1min electrical isolation between the analog inputs up to 30V AC and 50V DC Supply voltage sensitivity less than 0.1% of range span Power consumption 35VA max. Data buffering More than 4 years through lithium battery in RAM or 2 days with storage capacitor at 5 25 C ambient temperature. Additional backup in EEPROM. Electrical connection Electromagnetic compatibility (EMC) interference emission immunity to interference Housing ( and Type ) Housing type housing door Transport mechanism Chart cassette Bezel size Depth behind panel Panel cut-out At rear through plug-in screw terminals, max. conductor cross-section 2.5mm 2 or 2x 1.5mm 2 with core end sleeves. For : Setup connector at the front behind flip-up dot-matrix display EN Class B to industrial requirements Housing for front-panel mounting to IEC , galvanized sheet steel cast zink in corrosion-resistant chrome-nickel steel in plastic (polycarbonate) 144mm x 144mm 212mm without screw terminals; 227mm with screw terminals plugged in mm x mm Housing mounting in control panel to DIN Ambient temperature range Ambient temperature error Storage temperature range Climatic conditions 0 to +50 C 0.2%/10 C -20 to +70 C (without print head), -20 to +55 C (with print head) 20 70% relative humidity, no condensation Operating position normal position: vertical ± 30 (NL 90 ± 30, to DIN ) Protection to EN Category 2, front IP54 (IP65 with extra code 266), rear IP20 Weight 3.5 kg max. Approvals/marks of conformity Mark of conformity c UL us Testing laboratory Underwriters Laboratories Certificates / certification numbers Test basis E UL CAN/CSA C22.2 No valid for the flush-mounted instrument; not in conjunction with any housing extra code

5 JUMO GmbH & Co. KG Fulda, Germany Data Sheet Page 5/12 Operating modes Limit monitoring Eight limit comparators are available to monitor the limits. Limits, differential values (hysteresis), limit comparator functions (lk), texts and the channels to be monitored can be programmed. The result of the monitoring is fed to the open-collector outputs (1 3) and the optional relay module (1 8) as limit state (logic 0 or 1). The different lk functions are: lk 7: The limit state is set to 1 when: measurement > limit + upper differential. lk8: as lk7, but function is reversed. Chart speeds The LOGOPRINT 500 can be programmed with four different operating modes for the chart speed: 1. Normal operation 2. Limit operation If the measurement goes above/below the programmed limits, the recorder switches to the speed which has been programmed under limit operation. 3. External operation A signal on one of the logic inputs at the back of the recorder switches to the speed which has been programmed under external speed. 4. Timed operation The chart speed which is operative within a programmable time span. Type The LOGOPRINT 500 junior has no limit monitoring. Only normal operation is possible as chart speed. Graphic print-out Measurement traces Zoom (plot area) In zoom operation, an enlarged recording is made of a section of the full range of a trace. Presentation range (offset) This parameter is used to define the presentation range of a trace on the chart. This assists the evaluation, in particular of traces which are close to each other or which overlap. Peak value recording The peak value recording can be switched on or off for each channel. In the switched-off state, the present value of a channel is printed. Since more values can be measured than can be printed, the minimum and maximum values measured between two lines to be printed are stored when the peak value recording is switched on. These minimum and maximum values are printed when peak value recording is activated. Event traces Eight event traces can be printed. Limit monitoring (limit comparators) or the state of the optional logic inputs can thus be documented on the chart. Type The entire chart width for each measurement trace is available here. The functions zoom, presentation range, peak value recording and event traces are not applicable. Text printing Text printing is used for comments on the recorded trace and for event recording. Printing priorities can be assigned to texts, to serve as abort criteria during simultaneous text printing requests. Text printing can be separately configured for each text, either time-optimized or during continued recording of traces. Type The priorites and the printing mode are strictly defined here. Text printing facilities for and Type : - Time, date - Scaling of the channels - Channel numbers - Change of chart speed - Recording start/end text - Power on and power off text - Print text to check the printing system and the service print Additional text printing facilities for : - 16 limit comparator texts 1 (eight for underlimit and eight for overlimit) - 2 reports (calculate and print minimum, maximum and mean values) - Eight external texts 1 (extra code) - 16 binary-linked external texts 1 (extra code) - Event counter 1 (extra code) 1 These texts are buffered through a queue. As long as the queue is not full, complete documentation is assured. Extra codes RS422/RS485 interface This interface is intended for communication with higher-level systems (e. g. bus system or PC). It can be used to read out measurements, to monitor operating states and to transmit texts and values to the recorder. Logic inputs Eight logic inputs can be operated either through floating contacts or by the following voltage levels: inactive: 0 5V / active: 20 35V The voltage levels must be applied for 0.4sec. Functions available include: - External start/stop - Activate external chart speed - Text printing - Start/stop external report - Start scaling print - Increment two event counters - Key inhibit - Event traces Supply for 2-wire transmitter An electrically isolated supply for a 2-wire transmitter is available. 24V DC 45mA ± 5% ER8 external relay module The LOGOPRINT 500 can be equipped with an ER8 external relay module (eight relay outputs) to monitor infringements of upper and lower limits. The relay outputs are permanently assigned to the limit comparators. The assignment to the measurement channels can be made freely through the limit comparator parameter. Contact rating: 3 A 250V AC 50Hz, or 3 A 30V DC resistive load

6 JUMO GmbH & Co. KG Fulda, Germany Data Sheet Page 6/12 Display and controls Fault signal LED 24-character green LED dot-matrix display Print head Keys for operating and programming Setup interface (behind the swing-up LED dot-matrix display) Operation and configuration and Type At the recorder The eight keys on the instrument are used for operating the instrument, and to configure all the parameters essential to the operation. The 24-character dot-matrix display is available for indicating and monitoring the measurements and parameters. Housing door Chart paper Channel label Panel-mounting housing to IEC in galvanized sheet steel Setup program () Via the setup program for PC (accessory) The recorder can be configured using the setup program for PC (see diagram, bottom left) more conveniently than by using the instrument keys. The configuration data of a configured instrument can be read out and altered using the setup program. For a further instrument with the same configuration, the data can be copied through the setup program. The configuration data can be archived on data media and printed out. In addition to the programming possibilities from the keys of the recorder, the setup program offers the following extra functions: - Setting different print colors - Customer-specific linearizations - Setting the printing mode for the texts (printing mode: Overwrite measurement trace or Interrupt measurement trace ) - Printing priorities - Math and logic module editor - Various settings can be managed Customer-specific linearizations The setup program offers a choice between linear, square law and cube law linearization. There can be up to 41 calibration points for linear and square law linerarization, and up to 61 calibration points for cube law linearization. These calibration points are used to determine the coefficients for polynomials which are defined for each section, so that even a few calibration points produce a smooth graph. Accuracy: depends on the shape of the graph and the selected linearization. Language and Type The language setting (English, German, French) appears in the print-out and on the LED dot-matrix display.

7 JUMO GmbH & Co. KG Fulda, Germany Data Sheet Page 7/12 Example of a recording with text print-out for (1) Recording start/end text (2) Speed change to 120 mm/h through a logic input (3) Printing the time (with every fourth print-out, the current chart speed, the programmed instrument name, or the date are printed alternately). (4) If a selectable logic input is closed, the count of an event counter is incremented and documented together with the programmed text. Altogether, two event counters are available. (5) The scaling of all active channels can be printed, either by pressing the F key (hold down for at least 4 sec), or through a logic input. (6) The channel number can be printed in the selected channel color so that individual traces can be more easily differentiated. (7) Documentation of over/underlimit conditions in the limit comparators. (8) A total of eight event traces can be printed out. They can be used either to document the state of the limit comparators, or that of the logic inputs. The position of the event traces on the chart can also be programmed. (9) Additional texts (external texts) can be printed if one logic input, or a combination of up to four logic inputs, is switched. (10)Print-out of a report. The print-out shows the period of time in which the measurements were acquired and calculated, as well as the minimum, maximum and mean values of all active channels (including channel name and unit). (11)As opposed to (5), the scaling of the channels can be performed alternately in a programmable spacing. All texts which relate to a logic input can only be printed if the extra code 8 logic inputs (code 259) has been implemented in the recorder. In the example, the traces which were printed above the report (10), are printed out in the normal mode, i.e. all traces share the entire chart width (0 100mm). The presentation range can be selected freely on the chart for each trace. This assists the evaluation, in particular of traces which are close to one another or which overlap. The traces below the report have thus been arranged over two sections of the chart (0 50mm and mm). (1) (2) (3) (4) (3) (5) (1) (7) (9) (9) (7) (10) (6) (6) (6) (6) (8) (3) (11) (3) (3)

8 JUMO GmbH & Co. KG Fulda, Germany Data Sheet Page 8/12 Connection diagram for maximum terminal assignment Rear view of 3/6-channel version with plug-in screw-clamp connectors Connection for 3/6-channel version Diagram Supply as on label N neutral L1 line PE protective earth Connector 10. Analog inputs Inputs Connector Thermocouple Resistance thermometer in 2-wire circuit Resistance thermometer in 3-wire circuit Resistance thermometer in circuit

9 JUMO GmbH & Co. KG Fulda, Germany Data Sheet Page 9/12 Analog inputs Resistance transmitter in 3-wire circuit Inputs Connector Diagram A = start S = slider E = end Potentiometer in 2-wire circuit Potentiometer in 3-wire circuit Potentiometer in circuit Analog inputs and Type Voltage input up to ± 1V Inputs Connector Voltage input above ± 1V Current input ± 20mA Current input (shunt) ±20mA (when using transducers with changeable internal resistance; extra code terminal with shunt is required)

10 JUMO GmbH & Co. KG Fulda, Germany Data Sheet Page 10/12 Inputs/outputs Connector Diagram ER8 external relay module Communication with external relay module Voltage source for external 2-wire transmitter 24V 45mA ± 5% Logic operating inputs Contact operation LOW = R OFF 100kΩ HIGH = R ON 50kΩ 7. min. pulse length: HIGH 400msec LOW 400msec Open-collector outputs RS422/RS485 serial interface Voltage operation LOW = 0 5V DC (inactive) HIGH = 20 35V DC (active) contact no. 7 = logic input 1... contact no. 14 = logic input 8 DOUT1 DOUT4 U max = 32V DC I max = 100mA 8. Residual voltage DOUT active U DOUTactive = V Communication with higher-level systems 9. Overview of the electrical isolation

11 JUMO GmbH & Co. KG Fulda, Germany Data Sheet Page 11/12 Dimensions Panel-mounting housing Extra code Housing with carrying handle, rubber feet and terminal cover, also 3m mains cable with earthed plug Extra code Housing for wall mounting. The panel-mounting housing is fitted in a carrier and can be swung out through 90. Extra code TG-35 Portable recorder housing for varying applications in mobile use

12 JUMO GmbH & Co. KG Fulda, Germany Data Sheet Page 12/12 Order matrix: (1) Basic version /14 LOGOPRINT 500 with 3 universal inputs /15 LOGOPRINT 500 with 6 universal inputs /15 LOGOPRINT 500junior with 6 inputs for standard singals (2) Inputs 1 3 (programmable) x x x 888 factory-set x x x 999 configuration to customer specification 1 (3) Inputs 4 6 (programmable) x 000 not assigned x x 888 factory-set x x 999 configuration to customer specification 1 (4) Interface x x x 00 not assigned x x 52 RS422, Jbus, Modbus x x 53 RS485, Jbus, Modbus (5) Supply x x x V AC/DC +0/-0% 48 63Hz x x x V AC +10/-15% 48 63Hz (6) Extra codes x x x 020 lithium battery for RAM buffer (ex-factory) x x x 021 storage capacitor for RAM buffer (on request) x x x 030 terminal with shunt (6 items) x x logic inputs, interface for external relay module (ER8), voltage output 24V 50mA DC x x x 265 door with lock (IP54) x x x 266 IP65 seal, wide fixing brackets x x x 350 universal carrying case TG-35 2 x x x 351 housing with carrying handle 3 x x x 247 housing for wall mounting (can be swung through 90 ) 3 (1) (2) (3) (4) (5) (6) Order code /,... 4 Order example / / Please specify probe types and measurement ranges in plain text. 2 This extra code is available in combination with supply voltage V AC, not with low supply voltage. UL approval is not available. The protection type in the carrying case corresponds to IP20, outside IP20D. 3 UL approval is not available. 4 Extra codes are listed in sequence and separated by a comma. Standard accessories - 1 Operating Instructions - 2 mounting brackets - cable-tie with foot (can be released), for tension relief of the sensor leads connected - 1 print head, 3 colors (each color is available twice) or 1 print head, 6 colors - 1 roll chart 32m long and 1 fanfold chart pack 16m long Accessories (Data Sheet ) - For further accessories, see data sheet Consumables part number - Print head (2 items), 3 colors 70/ Print head (2 items), 6 colors 70/ Roll chart (5 rolls), no name, % graduation, linear; overall length 16m, overall width 120mm 70/ Roll chart (5 rolls), no name, % graduation, linear; overall length 32m, overall width 120mm 70/ Roll chart (5 rolls), no name, special graduation, linear; marked as specified - - Fanfold chart (5 packs), no name, % graduation, linear; overall length 16m, overall width 120mm 70/ Fanfold chart (5 packs), no name, special graduation, linear; marked as specified -