Compatible with an operating environment with coolants.

Transcription

1 Water Resistant Cylinder (Pneumatic/Hydraulic) Pneumatic: Series CM/CG1/MB/MB1/CQ/C/MGP/MGG Hydraulic: Series CHDKB/CH Compatible with an operating environment with coolants. nti-coolant performance has been improved compared to the standard cylinders. pplicable for an operating environment where water splashes. Courtesy of Steven Engineering, Inc.-30 Ryan Way, South San rancisco, C 9-0-Main Office: (6) Outside Local rea: (0)

2 Water Resistant ir Cylinders (Pneumatic/Hydraulic) Suitable for using under the atmosphere having coolant in the machine tools. lso, compatible with environments where water is splashed on the food machinery, or car washing machines, etc Special scraper Dramatically improved water resistance compared to standard cylinders Relation of Coolant Entry and Sliding Distance mount of coolant entry (g) Standard cylinder or rod size ø Sliding distance (km) Conditions Operating conditions ir Pressure 0.5 MPa Coolant Water-soluble Piston speed 0 mm/sec Operating cycle 60 cpm Two types of standard seal material Nitrile rubbers (NBR) luoro rubbers (KM) Water resistance improved 10 times by improving the waterproof effect of the switch substrate through a change of the internal structure. (SMC comparison) Model D-B(V)L/ Rail mounting D-5BL/ Tie-rod mounting D-HBL/ Band mounting D-G5BL/ Band mounting D-YBL/ Direct Note 1) mounting D-M9 (V)L/Direct Note 1) mounting pplicable cylinder CQ(ø to ø) CH(ø to ø) C(ø to ø) MB(ø to ø) CM, CG1(ø to ø) MGG(ø to ø) CG1(ø, ø) MGG(ø, ø) Note 1) Tie-rod mounting for C and MB Note ) This product is not made to be used in water. Refer to pages 1 to 131 for the detailed of es. C(ø to ø) MB(ø to ø) MB1(ø to ø) MGP(ø to ø) CHKDB(ø to ø) CQ(ø to ø) CHKDB(ø to ø) C(ø to ø) MB(ø to ø) MB1(ø to ø) MGP(ø to ø) Lead wire Oilproof vinyl cabtire cord: ø mm, cores (Brown, Blue), 3 m (standard) Oilproof vinyl cabtire cord: ø4, 0.3 mm cores (Brown, Blue), 3 m (standard) Oilproof vinyl cabtire cord: ø mm, cores (Brown, Blue), 3 m (standard) Oilproof vinyl cabtire cord: ø4, 0.3 mm cores (Brown, Blue), 3 m (standard) Oilproof vinyl cabtire cord: ø mm, cores (Brown, Blue), 3 m (standard) Oilproof vinyl cabtire cord:. x 3. Elliptical shape, 0.15 mm, cores (D-M9B(V)), 3 cores (D-M9N(V),D-M9P(V)) Hydraulic Cylinders Compact hydraulic cylinder conforming to JIS/10 MPa Series CHKDB ø to ø Hydraulic cylinder conforming to JIS/ MPa Series CH ø to ø pplicable Cylinder ir Cylinder Series CM ø to ø Series CG1 ø to ø ir cylinder Series MB ø to ø Square tube type air cylinder Series MB1 ø to ø Compact cylinder Series CQ ø to ø Series C ø to ø Compact guide cylinder Series MGP ø to ø Guide cylinder Series MGG ø to ø Courtesy of Steven Engineering, Inc.-30 Ryan Way, South San rancisco, C 9-0-Main Office: (6) Outside Local rea: (0)

3 ir Cylinders Series CM ø to ø Series CG1 ø to ø CDM Mounting Port thread type R Stroke HBL -XC6 CDG1 Mounting R Stroke HBL -XC6 With Nil Caution Rubber bumper ir cushion Rod seals and scrapers are not replaceable. The above parts cannot be replaced since the scraper is press-fit in the rod cover.,,, Rubber bumper, ir cushion Band mounting Piston rod, rod end nut made of stainless steel (-XC6) øe1h8 NN1 E1 E NN M x 1.5 NN M x 1.5 Other are the same as the double acting, single rod standard type. (n asterisk means it is the same as the standard type.) Mounting Bracket : Part No. Mounting bracket xial foot style lange Trunnion (with nuts) Min. order qty. 1 1 CM-L0C CM-0C CM-T0C The brackets for ø to ø are the same for the standard type. Order foot brackets for each cylinder unit. 898 NN øeh8 Description (t min. order qty.) foots, 1 mounting nut 1 flange 1 trunnion, 1 trunnion nut With Caution The scraper cannot be replaced since it is press-fit in the rod cover. Rubber bumper ir cushion (øe1) (øe1),,,,, Rubber bumper, ir cushion Band mounting Piston rod, rod end nut made of stainless steel (-XC6) (1) (1) G T W G T HBL G5BL S + Stroke ZZ + Stroke S + Stroke ZZ + Stroke ø to ø ø, ø (E1) E 30 (1) G S (85) 84 (93) 9 (109) 9 (109) 116 (130) 11 (131) T 1 W øe øe ZZ 1 (1) 136 (145) 15 (169) 15 (169) 0 (4) 1 (5) Other are the same as the double acting, single rod standard type. (n asterisk means it is the same as the standard type.) ( ): or the long stroke type Courtesy of Steven Engineering, Inc.-30 Ryan Way, South San rancisco, C 9-0-Main Office: (6) Outside Local rea: (0)

4 ir Cylinders Series MB ø to ø Series MB1 ø to ø MDB Mounting Port thread type R Stroke M9 (V)L -XC6 MDB1 Mounting Port thread type R Stroke M9 (V)L -XC6 With With ø,,,,, ir cushion Tie rod mounting Piston rod, rod end nut made of stainless steel (-XC6) ø,,,,, ir cushion Tie rod mounting Piston rod, rod end nut made of stainless steel (-XC6) H ZZ + Stroke H ZZ + Stroke 15 1 H ZZ 135 (141) 146 (15) 165 (13) 165 (13) 9 (9) 9 (9) Other are the same as the double acting, single rod standard type. ( ): or the type without an air cushion 15 1 H ZZ 135 (141) 146 (15) 165 (13) 165 (13) 9 (9) 9 (9) Other are the same as the double acting, single rod standard type. ( ): or the type without an air cushion Courtesy of Steven Engineering, Inc.-30 Ryan Way, South San rancisco, C 9-0-Main Office: (6) Outside Local rea: (0)

5 ir Cylinders Compact Cylinder Series CQ ø to ø Series C ø to ø CDQ Mounting Port thread type R Stroke D Option Z M9 (V)L -XC6 CD Mounting Port thread type R Stroke M9 (V)L -XC6 With B(V)L M9 (V)L ø to ø ø to ø With Nil Suffix Retaining ring, piston rod, rod end nut material: Stainless steel Piston rod, rod end nut, cover holding bolt material: Stainless steel Note) -XC6: ø to ø only Mounting,,,,,,, ø to ø B (through-hole) only ø to ø B (through-hole), (rod side flange) (both ends tapped), G (head side flange) L (foot), D (double clevis) None Retaining ring, piston rod, rod end nut material: Stainless steel (-XC6) Refer to page 4 for details. Rail mounting (D-BL/BVL)/Direct mounting (D-M9 (V)L) Use brackets for ø, ø,,,, ir cushion Tie-rod mounting style Piston rod, rod end nut material: Stainless steel (-XC6) Note 1) ir-hydro type, rod boot of Series C are excluded. Note ) Combination of es and steel tube is not available. Other are the same as the double acting, single rod standard type. 900 Courtesy of Steven Engineering, Inc.-30 Ryan Way, South San rancisco, C 9-0-Main Office: (6) Outside Local rea: (0)

6 ir Cylinders Compact guide cylinder Series MGP ø to ø Guide cylinder Series MGG ø to ø MGPM Port thread type R Stroke M9 (V)L MGGM Mounting Port thread type R Stroke HBL -XC6 Slide bearing Piston rods and guide rods are made of stainless steel. Iron parts made of stainless steel are available as made to order. scraper is installed on piston rod parts only. Double acting Bearing type Slide bearing,,,,,,, MGP R Rubber bumper MGP V Without cushion Direct mounting Note) MGP V is without cushion. Confirm the allowable kinetic energy for MGP V without cushion. Slide bearing HBL G5BL scraper is installed on piston rod parts only. ø to ø ø, ø Double acting,,,,, Bearing type Slide bearing Built-in rubber bumper and shock absorber Band mounting -XC6 Piston rod and rod end nut made of stainless steel -XC6 Stainless steel used on all iron parts -XC6B Stainless steel rod end moving parts -XC6C Stainless steel rods Note) RBL (anti-coolant) type is used for shock absorbers. ( other than the below are the same as the standard type.) ø to ø ront mounting flange B B + Stroke + Stroke ø to ø Q X Y + Stroke ront mounting flange Below strokes Between and 0 stokes Over 0 strokes Other are the same as the standard type. B B X Q Y + Stroke Q ( ): or the long stroke type. X Y (85) 84 (93) 9 (109) 11 (14) 13 (151) 138 (15) Courtesy of Steven Engineering, Inc.-30 Ryan Way, South San rancisco, C 9-0-Main Office: (6) Outside Local rea: (0)

7 Compact hydraulic cylinder conforming to JIS/10 MPa Hydraulic Cylinders Series CH KD ø to ø Hydraulic cylinder conforming to JIS/ MPa Series CH ø to ø CHDKDB Port thread type R Stroke End thread type M9 (V)L CHD Mounting Rod series R Stroke Option 5BL With M9 (V)L ø to ø,,,,,,, None Direct mounting øn C S B + Stroke + Stroke g h + Stroke Rod end male thread g B h C N Other are the same as the double acting, single rod standard type. Other are the same as the double acting, single rod standard type. S 6 6 With Piston seal is made of NBR for both R and V. Port position Stainless steel piston rods are available as made to order.,,,,, seal type Tie-rod mounting B type rod Other are the same as the double acting, single rod standard type. 90 Courtesy of Steven Engineering, Inc.-30 Ryan Way, South San rancisco, C 9-0-Main Office: (6) Outside Local rea: (0)

8 Water Resistant ir Cylinder/Water Resistant Hydraulic Cylinder Specific Product Precautions Be sure to read before handling. Refer to front matters 54 and 55 for Safety Instructions and pages 3 to 11 for ctuator and uto Switch Precautions. Handling Precautions 1. Before installing a cylinder, thoroughly flush out the piping to prevent dust or cutting chips from entering the cylinder. or the hydraulic cylinder, use the air bleed valve to bleed the air inside the cylinder.. Eccentric loads applied to the piston rod dramatically shorten the service life. Use the piston rod by always applying a load in an axial direction. 3. Make sure not to scratch or gouge the sliding portion of the piston rod, as this could damage the seals and lead to leaks. ttach a cover or other protection in locations where the cylinder is exposed to grinding sludge or machining chips. 4. When the cylinder is used in a place where the liquid from the piston rod is lightly splashed, and exposed to dust or sand, use a heavy duty scraper (-XC4). 5. If there is a possibility that liquid splashes on cylinder fittings when using an air cylinder, use insert fittings, self-align fittings, piping, etc. Consider the compatibility of liquid components and piping materials before using. 6. When selecting seals, generally use NBR (nitrile rubber) seals with liquids that do not contain chlorine and sulfur, and use KM (fluororubber) seals with liquids that contain chlorine and sulfur. However, depending on the type and the brand of liquid that splashes on the cylinder, the operating life of seals may be reduced dramatically (such as coolant liquid). In cases where special additives are used, or where liquid caused trouble with the conventional nitrile or fluororubber seals in the past, request an investigation or set up a test period for the use of the seals. Examples of coolants Shimiron, P-O-5 (Daido Chemical Industry Co., Ltd.) (NBR seals) Noritake Cool, G-S (Noritake Co., Ltd.) (NBR seals) Yushiroken, S-46S (Yushiro Chemical Industry Co., Ltd.) (NBR seals) Yushiroken, EC--T3 (Yushiro Chemical Industry Co., Ltd.) (NBR seals) Yushiron Oil, No. 3 (Yushiro Chemical Industry Co., Ltd.) (KM seals) Daphne Cut, Hs-1 (Idemitsu Kosan Co., Ltd.) (KM seals). Please consult with SMC separately when liquid contains sulfur, which is used for cylinders with a guide (MGP, MGG). Courtesy of Steven Engineering, Inc.-30 Ryan Way, South San rancisco, C 9-0-Main Office: (6) Outside Local rea: (0)