Check Valves. Direct and pilot operated check valve functions for applications up to 350 bar (5000 psi) and 227 L/min (60 USgpm)
|
|
- Basil Turner
- 7 years ago
- Views:
Transcription
1 Check Valves Direct and pilot operated check valve functions for applications up to 350 bar (5000 psi) and 7 L/min (60 USgpm) EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007 -
2 Check Valves Section Contents Typical Application Rated Flow Model Pressure bar (psi) L/min (USgpm) Page Check Valves - Introduction, features & benefits Check Valves, way CV (5000)...8 () CV (5000)...30 (8) CV 0/CV (3000)/350 (5000)...45 ()/45 () CV3 0/CV (3000)/350 (5000)...76 (0)/76 (0) CV (5000)...76 (0)... - CV (5000)...4 (30) CV 6/CV (3000)/350 (5000)...5 (40)/5(40) CV (3000)...7 (60) Check Valves with Bypass Orifice CV (5000)...76 (0) CV (3000)...5 (40)... - Restrictive Check Valves RCV (5000)...76 (0) Single Pilot Operated Check Valves, Cartridge Type SPC (3500)...9 (5) SPC (3000)...3 (6) Single Pilot Operated Check Valves, In-line Housing Type SPC (3000)...45 () SPC (3000)...5 (40) SPC (3000)...7 (60) Single Pilot Operated Check Valves, Cartridge Type (high pressure) POC (5000)...57 (5) POC (5000)...4 (30) Double Pilot Check Valves, Cartridge Type DPC (3500)...9 (5) Double Pilot Check Valves, In-line Housing Type DPC (3000)...45 () DPC (5000)...4 (30) DPC (3000)...5 (40) DPC (3000)...7 (60) EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007
3 Check Valves This section gives basic specifications for the full line of Vickers screw-in cartridge check valves. Its purpose is to provide a quick, convenient reference tool when choosing Vickers cartridge valves or designing a system using these components. The Vickers range of direct and pilot operated check valves provides the hydraulic circuit designer with a wide selection of cartridge and in-line products. Two pressure ratings are shown for all products featured in this catalog. The typical application pressure rating is the maximum recommended operating pressure for the valve in a given system. The fatigue pressure rating is the pressure for the valve to be free for infinite life from metal fatigue. All poppet type check valve cartridges have hardened and ground poppets and sharp-edged ground steel seats. This provides an excellent product that is dirt-tolerant, has reliable seating, and is suitable for fast cycling with long life. Direct operated check valves Cartridges fit into industry standard cavities and may be supplied for installation in manifolds, or be provided in standard housings having SAE or BSPP ports suitable for in-line mounting. A wide selection of cracking pressures is available from 0, to 0,7 bar (3 to 300 psi). Thus the opportunity exists to use the valves not only as conventional check but also as low pressure relief valves. Pilot operated check valves These valves are used for: Position load locking As an alternative to counterbalance valves where neither the overrunning loads or release speed are factors in the application. The high pressure POC*-0 and POC*- series of pilot-to-open check valves complement the CBV*-0 and CBV*- counterbalance cartridges and are physically interchangeable with them. The POC s provide a low cost alternative to load control when the dynamics of neither overrunning loads nor load release speed are factors to be considered in the design of the hydraulic circuit for the load to be controlled. The pilot-to-open valves positively lock a load from port to port until pilot pressure applied to port 3 is sufficient to unseat the valve. This then permits flow from port to port. The load can also be released through means of an optional screw type override. The POC*-0 covers flow up to 60 L/min (5 USgpm). The POC*- covers flow up to 4 L/min (30 USgpm). With infinite life qualification to a fatigue pressure rating of 30 bar (4500 psi), these POC valves are suitable for use in a broad range of load control applications with typical system operating pressures up to 350 bar (5000 psi). Tailoring of the circuit to gain energy savings while minimizing shock is obtained through the use of several standard cracking pressure ranges from,0 bar (30 psi) to 7 bar (00 psi). When anti-cavitation protection is required, the 0,30 bar (5 psi) spring should be used. For those applications where pilot pressure may not always be available, the valve can be ordered with an optional adjustable override. Features and benefits Products in this catalog have been fatigue tested for one million cycles at 3% or 0 million cycles at 5% of rated pressure. Simple load holding device. Low cost alternative to more complex solutions when overrunning loads are not present and / or control of load release speed is not required. Provides high operational efficiency and low spring settings. Valves are offered with a wide variety of standard housings with SAE and BSPP port options in the following configurations: In-line single In-line dual SAE, 4-bolt, code 6 Close coupled, nipple mounted asket mounted single asket mounted dual These valves can also be used in a C 0 3S or C 0 3S cavity. Four standard cracking pressures permit energy savings, while tailoring the hydraulic system requirements to minimize shock. Unique dual spring design provides high operational efficiency and a low pressure spring option for effective anticavitation protection. Unique design provides compact package and low pressure drops that match or exceed current market expectations and provide for excellent repeatability and stability. 3: pilot ratio satisfies simple load holding application requirements, while providing smooth operation and longer operating life. Optional adjustable override releases the load for situations where pilot pressure is not always available. Single pilot check Also offered are SPC-8 and SPC-0 single pilot check valves with pressures to 40 bar (3500 psi) and flows to 3 L/min (6 USgpm). These valves operate similar to the POC product but offer an opposite flow path which offers the designer a choice of pilot operated check valve when laying out a custom manifold for ease of design. Supporting products Vickers screw in cartridge valves are available in a wide range of mounting configurations and porting options to provide flexibility in developing circuits. Housings are available in either aluminum 0 bar (3000 psi) or steel 350 bar (5000 psi) configurations. All are available with a choice of BSPP (ISO 08/) or SAE style ports. EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007-3
4 CV3-4 Check valve Description The CV3-4-B is a ball type, screw-in cartridge check valve. Operation This valve remains closed until the bias is reached at port at which time the poppet lifts off the seat and allows flow from port to port. Functional Symbol Profile View RATINS AND SPECIFICATIONS Performance data is typical with fluid at,8 cst (05 SUS) and 49 C (0 F) Typical application pressure (all ports) 350 bar (5000 psi) Cartridge fatigue pressure (infinite life) 350 bar (5000 psi) Rated flow 7.6 L/min ( USgpm) Free flow cracking l/min (0.5 USgpm) 5 0,34 bar (5 psi) Internal leakage, Port to 5 drops/min 0 bar (3000 psi) Temperature range -40 to 0 C (-40 to 48 F) Cavity C 4 Fluids All general purpose hydraulic fluids such as: MIL H 5606, SAE 0, SAE 0, etc. Filtration Cleanliness code 8/6/3 Weight cartridge only 0,04 kg (0.09 lbs) Seal kit Buna N Viton Viton is a registered trademark of E.I. DuPont Pressure Drop Curves Cartridge only Pressure vs. Flow - L/min (,8 cst 49 C) Pressure Drop - psi Pressure Drop - bar Flow - USgpm (05 SUS 0 F) -4 EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007
5 Model Code CV3-4 CV3 4 (V) B *** ** Function 3 Seals Port size CV3 - Check valve Blank - Buna-N Cartridge only V - Viton Size 4-4 Size 4 Style B - Ball type 5 7 Special features 00 - None (Only required if valve has special features - omitted if 00 ) 6 Free flow cracking pressure 05-0,34 bar (5 psi) Dimensions mm (inch) Torque cartridge in aluminum or steel housing to Nm (6-0 ft. lbs) 9/6" HEX 7/6-0 UNF - A,73 (.50),8 (.859) Ø 8,64 (.340) Aluminum housings can be used for pressures up to 0 bar (3000 psi) Steel housings must be used for operating pressures above 0 bar (3000 psi) EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007-5
6 CV3-8 Check Valve Description The CV3 8 P is a direct acting, poppet type check valve. Operation This valve remains closed until the spring bias is reached at port. The poppet then lifts off the seat and allows flow from port to port. Functional Symbol Sectional View RATINS AND SPECIFICATIONS Performance data is typical with fluid at,8 cst (05 SUS) and 49 C (0 F) Typical application pressure (all ports) 350 bar (5000 psi) Cartridge fatigue pressure (infinite life) 80 bar (4000 psi) Rated flow 30 L/min (8 USgpm) Cracking L/min (0.5 USgpm) 4 0,8 bar (4 psi) 0 0,7 bar (0 psi) 5,03 bar (5psi) 5,7 bar (5 psi) 30,07 bar (30 psi) 60 4,0 bar (60 psi) Internal leakage 5 drops/min. 350 bar (5000 psi) Cavity C-8- Standard housing materials Aluminum or steel Temperature range -40 to 0 C (-40 to 48 F) Fluids All general purpose hydraulic fluids such as: MIL H 5606, SAE 0, SAE 0, etc. Filtration Cleanliness code 8/6/3 Weight cartridge only 0,05 kg (0. lb) Seal kits Buna N Viton Viton is a registered trademark of E.I.DuPont Pressure Drop Curves Cartridge only Flow - L/min (,8 cst 49 C) A CV3-8-P-O-60 B CV3-8-P-O-5 C CV3-8-P-O-0 D CV3-8-P-O-4 4 Pressure Drop - psi A B C D Pressure Drop - bar Flow - USgpm (05 SUS 0 F) -6 EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007
7 Model Code CV3-8 CV3 8 (V) P (*) ** *** Function CV3 Check Valve Size 8 8 Size 3 Seals Blank Buna-N V Viton 4 Style P Poppet 5 Valve housing material Omit for cartridge only A Aluminum S Steel 6 Port size 0 Cartridge only CODE PORT SIZE HOUSIN NUMBER Aluminum Steel Fatigue rated Fatigue rated 4T SAE T SAE T SAE /4 BSPP /8 BSPP See Section J for housing details. 7 Cracking Pressure 8 Special Features 004 0,8 bar (4 psi) 00 0,70 bar (0 psi) 05,03 bar (5psi) 05,70 bar (5 psi) 030,07 bar (30 psi) 060 4,00 bar (60 psi) 00 None (Only required if valve has special features - omitted if 00 ) SS - 36 Stainless Steel external components Dimensions mm(inch) Torque cartridge in aluminum or steel housing 34-4 Nm (5-30 ft. lbs), (0.87) hex 0.750" 6 Thd. 8,6 (0.34) 7,8 (.09) Ø,6 (0.497) Aluminum housings can be used for pressures up to 0 bar (3000 psi) Steel housings must be used for operating pressures above 0 bar (3000 psi) EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007-7
8 CV 0/CV-0 Check valve Description The CV-0-P and CV-0-P is a poppet type, screw-in cartridge check valve. Operation This valve remains closed until the bias is reached at port at which time the poppet lifts off the seat and allows flow from port to port. Functional Symbol Profile View RATINS AND SPECIFICATIONS Performance data is typical with fluid at,8 cst (05 SUS) and 49 C (0 F) Typical application pressure (all ports) CV/CV 0 bar (3000 psi)/350 bar (5000 psi) Cartridge fatigue pressure (infinite life) CV/CV 0 bar (3000 psi)/350 bar (5000 psi) Rated flow 45 L/min ( USgpm) Free flow cracking L/min (0.5 USgpm) 005 0,34 bar (5 psi) 05,03 bar (5 psi) 030,07 bar (30 psi) 065 4,48 bar (65 psi) 080 5, bar (80 psi) 00 6,90 bar (00 psi) 40 9,66 bar (40 psi) 60 7,93 bar (60 psi) 300 0,7 bar (300 psi) Internal leakage, Port to 5 drops / min. 350 bar (5000 psi) Temperature range 40 to 0 C ( 40 to 48 F) Cavity C 0 Fluids All general purpose hydraulic fluids such as: MIL H 5606, SAE 0, SAE 0, etc. Filtration Cleanliness code 8/6/3 Standard housing materials Aluminum or Steel Weight cartridge only 0,08 kg (0.7 lb) Seal kit Buna N Viton Viton is a registered trademark of E.I.DuPont Pressure Drop Curves Cartridge only Pressure Drop - psi Flow - L/min (,8 St 49 C) A 6 50 B 4 C Flow - USgpm (05 SUS 0 F) A - CV(*) 0*P B - CV(*) 0*P C - CV(*) 0*P Pressure Drop - bar -8 EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007
9 Model Code CV-0 CV(*) 0 * P * ** *** Function CV Check valve 0 bar (3000 psi) CV Check valve 350 bar (5000 psi) Size 0 0 Size 3 Seals N Buna-N V Viton 4 Style P Poppet 5 Valve housing material 0 Cartridge only A Aluminum S Steel 6 Port size 00 Cartridge only CODE PORT SIZE HOUSIN NUMBER Aluminum Aluminum Steel Light Duty Fatigue rated Fatigue rated 3B 3/8 BSPP T SAE T SAE /4 BSPP /8 BSPP H SAE H SAE See Section J for housing details. 7 Free flow cracking 8 Special Features pressure 00 None 005 0,34 bar (5 psi) 080 5, bar (80 psi) (Only required if valve has (Anti-cavitation) 00 6,90 bar (00 psi) special features - omitted 05,03 bar (5 psi) 40 9,66 bar (40 psi) if 00 ) 030,07 bar (30 psi) 60 7,93 bar (60 psi) SS - 36 Stainless Steel 065 4,48 bar (65 psi) 300 0,70 bar (300 psi) external components Dimensions mm (inch) 5,4 (.0) hex 8,0 (0.3) Torque cartridge in housing A Nm (35-40 ft. lbs) S Nm (50-55 ft. lbs) 0.875" 4 Thd. 3,7 (.5) Ø 5,80 (0.6) Aluminum housings can be used for pressures up to 0 bar (3000 psi) Steel housings must be used for operating pressures above 0 bar (3000 psi) EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007-9
10 CV3-0/CV3-0 Check valve Description The CV3-0-P and CV3-0-P is a poppet type, screw-in cartridge check valve. Operation This valve remains closed until the spring bias is reached at port at which time the poppet lifts off the seat and allows flow from port to port. Functional Symbol Sectional View RATINS AND SPECIFICATIONS Performance data is typical with fluid at,8 cst (05 SUS) and 49 C (0 F) Typical application pressure (all ports) CV3/CV3 0 bar (3000 psi)/350 bar (5000 psi) Cartridge fatigue pressure (infinite life) CV3/CV3 0 bar (3000 psi)/350 bar (5000 psi) Rated flow 76 L/min (0 USgpm) Free flow cracking L/min (0.5 USgpm) 003 0, bar (3 psi) 00 0,69 bar (0 psi) 00,38 bar (0 psi) 035,4 bar (35psi) 040,76 bar (40 psi) 065 4,48 bar (65 psi) 00 6,90 bar (00 psi) 80,40 bar (80 psi) 0 4,50 bar (0 psi) Internal leakage, Port to 5 drops / min. 350 bar (5000 psi) Temperature range 40 to 0 C ( 40 to 48 F) Cavity C 0 Fluids All general purpose hydraulic fluids such as MIL H 5606, SAE 0, SAE 0, etc. Filtration Cleanliness code 8/6/3 Standard housing materials Aluminum or steel Weight cartridge only 0,08 kg (0.7 lb) Seal kit Buna N Viton Viton is a registered trademark of E.I.DuPont Pressure Drop Curves Cartridge only Flow - L/min (,8 cst 49 C) A - CV(*)3 0*P B - CV(*)3 0*P C - CV(*)3 0*P Pressure Drop - psi A 0 B C Flow - USgpm (05 SUS 0 F) Pressure Drop - bar -0 EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007
11 Model Code CV3-0 CV(*)3 0 * P * ** *** Function CV3 Check valve 0 bar (3000 psi) CV3 Check valve 350 bar (5000 psi) Size 0 0 Size 3 Seals N Buna-N V Viton 4 Style P Poppet 5 Valve housing material 0 None A Aluminum S Steel 6 Port size 00 Cartridge only CODE PORT SIZE HOUSIN NUMBER Aluminum Aluminum Steel Light Duty Fatigue rated Fatigue rated 3B 3/8 BSPP T SAE T SAE /4 BSPP /8 BSPP H SAE H SAE See Section J for housing details. 7 Free flow cracking 8 Special Features pressure 003 0, bar (3 psi) (Anti-cavitation) 00 0,69 bar (0 psi) (Anti-cavitation) 00,38 bar (0 psi) 035,4 bar (35psi) 040,76 bar (40 psi) 065 4,48 bar (65 psi) 00 6,90 bar (00 psi) 80,4 bar (80 psi) 0 4,5 bar (0 psi) 00 None (Only required if valve has special features - omitted if 00 ) SS - 36 Stainless Steel external components Dimensions mm (inch) 5,4 (.0) hex 8,0 (0.3) Torque cartridge in housing A Nm (35-40 ft. lbs) S Nm (50-55 ft. lbs) 0.875" 4 Thd. 3,7 (.5) Ø 5,80 (0.6) Aluminum housings can be used for pressures up to 0 bar (3000 psi) Steel housings must be used for operating pressures above 0 bar (3000 psi) EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007 -
12 CV6-0 Check Valve (side in, nose out) Description The CV6-0-P is a poppet type, screw-in cartridge check valve. Operation This valve remains closed until the spring bias is reached at port at which time the poppet lifts off the seat and allows flow from port to port. Functional Symbol Sectional View RATINS AND SPECIFICATIONS Performance data is typical with fluid at,8 cst (05 SUS) and 49 C (0 F) Typical application pressure (all ports) 350 bar (5000 psi) Cartridge fatigue pressure (infinite life) 30 bar (4500 psi) Rated flow 76 L/min (0 USgpm) Free flow cracking L/min (0.5 USgpm) 5 0,34 bar (5 psi) 5,03 bar (5 psi) 5,70 bar (5 psi) 50 3,40 bar (50 psi) Internal leakage, Port to 5 drops / min. 350 bar (5000 psi) Temperature range 40 to 0 C ( 40 to 48 F) Cavity C 0 Fluids All general purpose hydraulic fluids such as: MIL H 5606, SAE 0, SAE 0, etc. Filtration Cleanliness code 8/6/3 Standard housing materials Aluminum or steel Weight cartridge only 0,08 kg (0.7 lb) Seal kit Buna N Viton Viton is a registered trademark of E.I.DuPont Pressure Drop Curves Cartridge only Flow - L/min (,8 cst 49 C) A CV6-0-P-O-50 B CV6-0-P-O-5 C CV6-0-P-O-5 D CV6-0-P-O-5 Pressure Drop - psi A B C 6 3 Pressure Drop - bar D Flow - USgpm (05 SUS 0 F) - EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007
13 Model Code CV6-0 CV6 0 (V) P (*) ** *** Function CV6 Check Valve Size 0 0 Size 3 Seals Blank Buna-N V Viton 4 Style P Poppet 5 Valve housing material Omit for cartridge only A Aluminum S Steel 6 Port size 0 Cartridge only CODE PORT SIZE HOUSIN NUMBER 7 Free flow cracking pressure 5 0,34 bar (5 psi) (Anticavitation) 5,03 bar (5 psi) 5,70 bar (5 psi) 50 3,40 bar (50 psi) Aluminum Aluminum Steel Light duty Fatigue rated Fatigue rated 3B 3/8 BSPP T SAE T SAE /4 BSPP /8 BSPP H SAE H SAE See Section J for housing details. 8 Special Features 00 None (Only required if valve has special features - omitted if 00 ) SS - 36 Stainless Steel external components Dimensions mm (inch) 5,4 (.0) hex 8,0 (0.3) Torque cartridge in housing A Nm (35-40 ft. lbs) S Nm (50-55 ft. lbs) 0.875" 4 Thd. 3,7 (.5) WARNIN The cavity should be machined to the 4,9 (0.56) maximum diameter and 36,00 (.47) maximum depth (see cavity detail, page M-). Ø 5,80 (0.6) Aluminum housings can be used for pressures up to 0 bar (3000 psi) Steel housings must be used for operating pressures above 0 bar (3000 psi) EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007-3
14 CV- Check valve Description The CV- is a poppet type, screw-in cartridge check valve. Operation This valve remains closed until the spring bias is reached at port at which time the poppet lifts off the seat and allows flow from port to port. Functional Symbol Profile View RATINS AND SPECIFICATIONS Performance data is typical with fluid at,8 cst (05 SUS) and 49 C (0 F) Typical application pressure (all ports) 350 bar (5000 psi) Cartridge fatigue pressure (infinite life) 350 bar (5000 psi) Rated flow 4 L/min (30 USgpm) Free flow cracking L/min (0.5 USgpm).5 0,7 bar (.5 psi) 5.0 0,35 bar (5.0 psi) 0 0,69 bar (0 psi) 0,38 bar (0 psi) 40,76 bar (40 psi) 80 5,50 bar (80 psi) 60,0 bar (60 psi) Internal leakage, Port to 5 drops / min. 350 bar (5000 psi) Hysteresis Less than 0,35 bar (5 psi) Temperature range 40 to 0 C ( 40 to 48 F) Cavity C or C U Fluids All general purpose hydraulic fluids such as: MIL H 5606, SAE 0, SAE 0, etc. Filtration Cleanliness code 8/6/3 Standard housing materials Aluminum or steel Weight cartridge only 0,4 kg (0.54 lb) Seal kit Buna N Viton Viton is a registered trademark of E.I.DuPont Pressure Drop - psi Pressure Drop Curves Cartridge only Flow - L/min (,8 cst 49 C) 0 40 A B C Flow - USgpm (05 SUS 0 F) Pressure Drop - bar A CV--P-O-80 B CV--P-O-0 C CV--P-O-.5-4 EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007
15 Model Code CV- CV (V) P (*) *** (U) ** Function CV Check valve Size Size 3 Seals Blank Buna-N V Viton 4 Style P Poppet 5 Valve housing material Omit for cartridge only A Aluminum S Steel 6 Port size 0 Cartridge only CODE PORT SIZE HOUSIN NUMBER C--U C-- C--U C-- Aluminum Aluminum Steel Steel Fatigue rated Fatigue rated Fatigue rated Fatigue rated 0T SAE T SAE / BSPP /4 BSPP See Section J for housing details. 7 Cavity 8 9 Blank Cavity without undercut U Cavity with undercut Cracking pressure.5 0,7 bar (.5 psi) 5.0 0,35 bar (5 psi) 0 0,69 bar (0 psi) 0,38 bar (0 psi) 40,75 bar (40 psi) 80 5,50 bar (80 psi) 60,0 bar (60 psi) Special Features 00 None (Only required if valve has special features - omitted if 00 ) Dimensions mm (inch),6 (.5) hex Torque cartridge in housing A Nm (60-70 ft. lbs) S Nm (75-85 ft. lbs) Aluminum housings can be used for pressures up to 0 bar (3000 psi) Steel housings must be used for operating pressures above 0 bar (3000 psi)..06" Thd. 44,7 (.76) 8,9 (0.75) Ø 3,75 (0.935) EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007-5
16 CV-6/CV-6 Check Valve Description The CV-6-P and CV-6-P are poppet type, screw-in cartridge check valves. Operation This valve remains closed until the spring bias is reached at port at which time the poppet lifts off the seat and allows flow from port to port. Functional Symbol Sectional View CV-6 Shown RATINS AND SPECIFICATIONS Performance data is typical with fluid at,8 cst (05 SUS) and 49 C (0 F) Typical application pressure (all ports) CV-6: 0 bar (3000 psi) / CV-6: 350 bar (5000 psi) Cartridge fatigue pressure (infinite life) CV-6: 0 bar (3000 psi) / CV-6: 350 bar (5000 psi) Rated flow 5 L/min (40 USgpm) Free flow cracking L/min (0.5 USgpm) 5 0,34 bar (5 psi) 0,34 bar (0 psi) 30,07 bar (30 psi) 40,67 bar (40 psi) 50 3,45 bar (50 psi) 00 6,90 bar (00 psi) Note: Only 5 psi option available for CV-6 Internal leakage, Port to 5 drops / min. 0 bar (3000 psi) Temperature range 40 to 0 C ( 40 to 48 F) Cavity C 6 Fluids All general purpose hydraulic fluids such as: MIL H 5606, SAE 0, SAE 0, etc. Filtration Cleanliness code 8/6/3 Standard housing materials Steel or Aluminum Weight cartridge only 0,6 kg (0.58 lb) Seal kit Buna N Viton Viton is a registered trademark of E.I.DuPont Pressure Drop Curves Cartridge only Pressure Drop - psi B Flow - L/min (,8 cst 49 C) A Pressure Drop - bar A CV(*)-6-P-O-50 B CV(*)-6-P-O-0 C CV(*)-6-P-O-5 D CV(*)-6-P-O-5 0 D C Flow - USgpm (05 SUS 0 F) -6 EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007
17 Model Code CV-6/CV-6 CV(*) 6 (V) P *** ** Function CV Check Valve 0 bar CV Check Valve 350 bar Size 6 6 Size 3 Seals Blank Buna-N V Viton 4 Style P Poppet 5 Port size 0 Cartridge only CODE PORT SIZE HOUSIN NUMBER Aluminum Aluminum Steel Light duty Fatigue rated Fatigue rated 6B 3/4 BSPP T SAE T SAE / BSPP /4 BSPP H SAE H SAE 5663 See Section J for housing details. 6 Free flow cracking pressure 5 0,34 bar (5 psi) (Anti-cavitation) 0,34 bar (0 psi) 30,07 bar (30 psi) 40,67 bar (40 psi) 50 3,45 bar (50 psi) 00 6,90 bar (00 psi) Only 5 psi option available for CV-6 7 Special Features 00 None (Only required if valve has special features - omitted if 00 ) Dimensions mm (inch) Torque cartridge housing: A 08- Nm (80-90 ft. lbs) S Nm (00-0 ft. lbs) 38, (.5) hex.3" Thd. 3,0 (0.5) 44,5 (.75) Ø 8,5 (.) Aluminum housings can be used for pressures up to 0 bar (3000 psi) Steel housings must be used for operating pressures above 0 bar (3000 psi) EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007-7
18 CV-0 Check valve Description The CV-0-P is a poppet type, screw-in cartridge check valve. Operation This valve remains closed until the spring bias is reached at port at which time the poppet lifts off the seat and allows flow from port to port. Functional Symbol Sectional View RATINS AND SPECIFICATIONS Performance data is typical with fluid at,8 cst (05 SUS) and 49 C (0 F) Typical application pressure (all ports) 0 bar (3000 psi) Cartridge fatigue pressure (infinite life) 0 bar (3000 psi) Rated flow 7 L/min (60 USgpm) Free flow cracking L/min (0.5 USgpm) 5 0,34 bar (5 psi) 5,03 bar (5 psi) 30,07 bar (30 psi) 60 4,4 bar (60 psi) 00 6,90 bar (00 psi) Internal leakage, Port to 5 drops / min. bar (3000 psi) Temperature range 40 to 0 C ( 40 to 48 F) Cavity C 0 Fluids All general purpose hydraulic fluids such as: MIL H 5606, SAE 0, SAE 0, etc. Filtration Cleanliness code 8/6/3 Standard housing materials Aluminum Weight cartridge only 0,49 kg (.09 lb) Seal kit Buna N Viton Viton is a registered trademark of E.I.DuPont Pressure Drop Curves Cartridge only Flow - L/min (,8 cst 49 C) A CV-0-P-O-00 B CV-0-P-O-30 C CV-0-P-O-5 Pressure Drop - psi A B C Pressure Drop - bar Flow - USgpm (05 SUS 0 F) -8 EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007
19 Model Code CV-0 CV 0 (V) P *** *** Function CV Check valve Size 0 0 Size 3 Seals Blank Buna-N V Viton 4 Style P Poppet 5 Port size 0 Cartridge only CODE PORT SIZE HOUSIN NUMBER Aluminum Aluminum Light duty Fatigue rated 8B BSPP T SAE /4 BSPP BSPP H SAE H SAE See Section J for housing details. 6 Free flow cracking pressure 5 0,34 bar (5 psi) (Anti-cavitation) 5,03 bar (5 psi) 30,07 bar (30 psi) 60 4,4 bar (60 psi) 00 6,90 bar (00 psi) 7 Special Features 00 None (Only required if valve has special features - omitted if 00 ) Dimensions mm (inch) 47,6 (.87) hex 4,0 (0.55) Torque cartridge in aluminum housing 8-55 Nm (95-5 ft. lbs).65" Thd. 57, (.5) Ø 36,44 (.435) EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007-9
20 CV6-0 Orifice check valve Description The CV6-0-P is a poppet type, screw-in cartridge check valve with bypass orifice. Functional Symbol Sectional View Operation This valve acts a restrictor in the to direction and as a check valve it allows free flow from to. RATINS AND SPECIFICATIONS Performance data is typical with fluid at,8 cst (05 SUS) and 49 C (0 F) Typical application pressure (all ports) 350 bar (5000 psi) Cartridge fatigue pressure (infinite life) 350 bar (5000 psi) Rated flow 76 L/min (0 USgpm) Free flow cracking L/min (0.5 USgpm) 003 0, bar (3 psi) 00 0,69 bar (0 psi) 00,38 bar (0 psi) 035,4 bar (35 psi) 040,76 bar (40 psi) 065 4,48 bar (65 psi) 00 6,90 bar (00 psi) 80,40 bar (80 psi) 0 4,50 bar (0 psi) Orifice size range 0.05 to 0.5 ( mm) Temperature range -40 to 0 C (-40 to 48 F) Cavity C 0 Fluids All general purpose hydraulic fluids such as MIL H 5606, SAE 0, SAE 0, etc. Filtration Cleanliness code 8/6/3 Standard housing materials Aluminum or steel Weight cartridge only 0,08 kg (0.7 lbs) Seal kit Buna N Viton Viton is a registered trademark of E.I. DuPont Pressure Drop Curves Cartridge only 500 Flow - L/min (,8 cst 49 C) A - CV6 0*P B - CV6 0*P C - CV6 0*P Pressure Drop - psi A B C Flow - USgpm (05 SUS 0 F) Port to Pressure Drop - bar -0 EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007
21 Model Code CV6-0 CV6 0 * P * ** *** ** Function 5 Valve housing material CV6 - Check valve with bypass orifice Size 0-0 Size 3 Seals N - Buna-N V - Viton 4 Style P - Poppet 0 - No housing A - Aluminum S - Steel 7 Free flow cracking pressure 003-0, bar (3 psi) (Anti-cavitation) 00-0,69 bar (0 psi) (Anti-cavitation) 00 -,38 bar (0 psi) 035 -,4 bar (35 psi) 040 -,76 bar (40 psi) 065-4,48 bar (65 psi) 00-6,90 bar (00 psi) 80 -,4 bar (80 psi) 0-4,5 bar (0 psi) 6 Port size 00 - Cartridge only CODE PORT SIZE HOUSIN NUMBER Aluminum Aluminum Steel Light duty Fatigue rated Fatigue rated 3B 3/8 BSPP T SAE T SAE /4 BSPP /8 BSPP H SAE H SAE See Section J for housing details. 8 Orifice size 9 Special features Specify in thousandths of an inch Ø max Ø min 00 - None (Only required if valve has special features - omitted if 00 ) SS - 36 Stainless Steel external components Dimensions mm (inch) Torque cartridge in housing A Nm (35-40 ft. lbs) S Nm (50-55 ft. lbs) 5,4 (.0) hex 0.875" 4 Thd. 3,7 (.5) 8,0 (0.3) Ø 5,80 (0.6) Aluminum housings can be used for pressures up to 0 bar (3000 psi) Steel housings must be used for operating pressures above 0 bar (3000 psi) EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007 -
22 CV6-6 Orifice check valve Description The CV6-6-P is a poppet type, screw-in cartridge check valve with bypass orifice. Operation This valve acts a restrictor in the to direction and as a check valve it allows free flow from to. Functional Symbol Sectional View RATINS AND SPECIFICATIONS Performance data is typical with fluid at,8 cst (05 SUS) and 49 C (0 F) Typical application pressure (all ports) 0 bar (3000 psi) Cartridge fatigue pressure (infinite life) 0 bar (3000 psi) Rated flow 5 L/min (40 USgpm) Free flow cracking L/min (0.5 USgpm) 005 0,34 bar (3 psi) 00,34 bar (0 psi) 030,07 bar (30 psi) 050 3,45 bar (50 psi) Orifice size range inch ( mm) Temperature range -40 to 0 C (-40 to 48 F) Cavity C 6 Fluids All general purpose hydraulic fluids such as MIL H 5606, SAE 0, SAE 0, etc. Filtration Cleanliness code 8/6/3 Standard housing materials Aluminum Weight cartridge only 0,6 kg (0.58 lbs) Seal kit Buna N Viton Viton is a registered trademark of E.I. DuPont Pressure Drop Curves Cartridge only A - CV6 6*P B - CV6 6*P C - CV6 6*P Pressure Drop - psi Flow - L/min (,8 cst 49 C) A 4 B C Pressure Drop - bar Flow - USgpm (05 SUS 0 F) Port to - EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007
23 Model Code CV6-6 CV6 6 * P * *** *** *** Function 5 Block material CV6 - Check valve with bypass orifice 0 - No housing A - Aluminum Size 6-6 Size 3 Seals N - Buna-N V - Viton 4 Style P - Poppet 7 Free flow cracking pressure 005-0, bar (5 psi) (Anti-cavitation) 00 -,34 bar (0 psi) 030 -,07 bar (30 psi) 040 -,76 bar (40 psi) 050-3,45 bar (50 psi) 00-6,90 bar (00 psi) 6 Port size Cartridge only CODE PORT SIZE HOUSIN NUMBER Aluminum Aluminum Light duty Fatigue rated 6B 3/4 BSPP T SAE / BSPP /4 BSPP H SAE H SAE 5663 See Section J for housing details. 8 Orifice size 9 Special features Specify in thousandths of an inch Ø max Ø min 00 - None (Only required if valve has special features - omitted if 00 ) Dimensions mm (inch) Torque cartridge in aluminum housing 08- Nm (80-90 ft. lbs).5" HEX.3"- Thd. 44,58 (.75),7 (.500) Ø 8,53 (.3) EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007-3
24 RCV3-0 Restrictive check valve Description The RCV3-0-P is a poppet type, screw-in cartridge check valve with stroke limiter. Operation This valve remains closed until the spring bias is reached at port at which time the poppet lifts off the seat and allows flow from port to port. The effective orifice in the free flow direction is adjustable. Functional Symbol Sectional View RATINS AND SPECIFICATIONS Performance data is typical with fluid at,8 cst (05 SUS) and 49 C (0 F) Typical application pressure (all ports) 350 bar (5000 psi) Cartridge fatigue pressure (infinite life) 350 bar (5000 psi) Rated flow 76 L/min (0 USgpm) Free flow cracking L/min (0.5 USgpm) 003 0, bar (3 psi) 00 0,69 bar (0 psi) 00,38 bar (0 psi) 040,76 bar (40 psi) 065 4,48 bar (65 psi) 00 6,90 bar (00 psi) 80,40 bar (80 psi) 0 4,50 bar (0 psi) Internal leakage, Port to 5 drops/min 0 bar (3000 psi) Temperature range -40 to 0 C (-40 to 48 F) Cavity C 0 Fluids All general purpose hydraulic fluids such as MIL H 5606, SAE 0, SAE 0, etc. Filtration Cleanliness code 8/6/3 Standard housing materials Aluminum or steel Weight cartridge only 0, kg (0.48 lbs) Seal kit Buna N Viton Viton is a registered trademark of E.I. DuPont Pressure Drop Curves Cartridge only 500 Flow - L/min (,8 cst 49 C) A - RCV3 0* P B - RCV3 0* P C - RCV3 0* P Pressure Drop - psi A B C Flow - USgpm (05 SUS 0 F) Port to with fully open adjustment Pressure Drop - bar -4 EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007
25 Model Code RCV3-0 RCV3 0 * P * ** *** Function 5 Block material RCV3 - Check valve with stroke limiter (Restrictive check valve) O - No block A - Aluminum S - Steel Size 0-0 Size 3 Seals N - Buna-N V - Viton 4 Style P - Poppet Dimensions mm (inch) 7 Free flow cracking pressure 003-0, bar (3 psi) (Anti-cavitation) 00-0,69 bar (0 psi) (Anti-cavitation) 00 -,38 bar (0 psi) 040 -,76 bar (40 psi) 065-4,48 bar (65 psi) 00-6,90 bar (00 psi) 80 -,4 bar (80 psi) 0-4,5 bar (0 psi) 6 Port size 00 - Cartridge only CODE PORT SIZE HOUSIN NUMBER Aluminum Aluminum Steel Light duty Fatigue rated Fatigue rated 3B 3/8 BSPP T SAE T SAE /4 BSPP /8 BSPP H SAE H SAE See Section J for housing details. 8 Special features 00 - None (Only required if valve has special features - omitted if 00 ) Torque cartridge in housing A Nm (35-40 ft. lbs) S Nm (50-55 ft. lbs) 47,65 (.876) " HEX 3,7 (.49) 0.875"-4 Thd. Ø 5.8 (.6) Aluminum housings can be used for pressures up to 0 bar (3000 psi) Steel housings must be used for operating pressures above 0 bar (3000 psi) EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007-5
26 SPC-8 Single pilot check valve Description The SPC 8 is a poppet type, pilot-to-open, screw-in cartridge type check valve. Operation The SPC 8 allows flow from port to port 3 when the spring bias is overcome. Flow is blocked from port 3 to port until sufficient pilot pressure is applied at port. Functional Symbol 3 Sectional View 3 RATINS AND SPECIFICATIONS Performance data is typical with fluid at,8 cst (05 SUS) and 49 C (0 F)) Typical application pressure (all ports) 40 bar (3500 psi) Cartridge fatigue pressure (infinite life) 40 bar (3500 psi) Rated flow 9 L/min (5 USgpm) Pilot ratio 3: Cracking pressure 5,0 bar (5 psi) 35,4 bar (35 psi) 65 4,5 bar (65 psi) Internal leakage. All leakage 40 bar (3500 psi) Port 3 to 5 drops / min. 40 bar (3500 psi) Port to Unsealed piston* 40 cc/min. maximum, zero leakage with sealed piston. *Unsealed piston only supplied with 5 psi spring option. Temperature range -40 to 0 C (-40 to 48 F) Cavity C 8 3 Fluids All general purpose hydraulic fluids such as: MIL H 5606, SAE 0, SAE 0, etc. Filtration Cleanliness code 8/6/3 Standard housing materials Aluminum or steel Weight cartridge only 0,07 kg (0.5 lb) Seal kit Buna N Viton Viton is a registered trademark of E.I. DuPont Pressure Drop Curves Cartridge only Pressure Drop - psi Flow - L/min (,8 cst 49 C) A 0 B C 4 0 D Pressure Drop - bar A 65 psi (port to 3) B 35 psi (port to 3) C 5 psi (port to 3) D Port 3 to (piloted open) WARNIN Do not use Single pilot check valves in load holding applications where either overrunning loads are possible; or, load release speed is critical. Failure to observe these guidelines may result in bodily injury or damage to equipment. Flow - USgpm (05 SUS 0 F) -6 EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007
27 Model Code SPC-8 SPC 8 (X) P (*) ** ** Function SPC Single pilot check valve Size 8 8 Size 3 Seals Blank Buna-N V Viton U Buna-N with no piston seals W Viton with no piston seals 4 Style P Poppet 5 Valve housing material Omit for cartridge only A Aluminum S Steel 6 Port size 7 Cracking Pressure 0 Cartridge only 5,0 bar (5 psi) CODE PORT SIZE HOUSIN NUMBER 35,4 bar (35 psi) 65 4,5 bar (65 psi) Aluminum Steel Fatigue rated Fatigue rated 4T SAE T SAE /4 BSPP /8 BSPP See Section J for housing details. 8 Special Features 00 None (Only required if valve has special features - omitted if 00 ) SS - 36 Stainless Steel external components Dimensions mm (inch) Torque cartridge in aluminum or steel housing to 34-4 Nm (5-30 ft. lbs), (0.87) hex 0.750" 6 Thd. 8,5 (0.33) 3 4,4 (.63) Ø 4, (0.559) Ø 5,8 (0.6) Aluminum housings can be used for pressures up to 0 bar (3000 psi) Steel housings must be used for operating pressures above 0 bar (3000 psi) EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007-7
28 SPC-0 Single pilot check valve Description The SPC-0 is a poppet type pilot-to-open check valve, screw-in cartridge type. Operation This valve allows flow from Port to Port 3, when the spring bias is overcome. Flow is blocked from Port 3 to Port until sufficient pilot pressure is applied at Port. Functional Symbol 3 Sectional View 3 Pressure Drop - psi RATINS AND SPECIFICATIONS Performance data is typical with fluid at,8 cst (05 SUS) and 49 C (0 F) Typical application pressure (all ports) 0 bar (3000 psi) Cartridge fatigue pressure (infinite life) 0 bar (3000 psi) Rated flow 3 L/min (6 USgpm) Cracking L/min (0.5 USgpm) 5,7 bar (5 psi) 50 3,45 bar (50 psi) 00 6,90 bar (00 psi) Internal leakage, Port 3 to 5 drops / min. 0 bar (3000 psi) Temperature range 40 to 0 C ( 40 to 48 F) Pilot ratio 4: Cavity C 0 3 Fluids All general purpose hydraulic fluids such as: MIL H 5606, SAE 0, SAE 0, etc. Filtration Cleanliness code 8/6/3 Standard housing materials Aluminum Weight cartridge only 0,08 kg (0.8lb) Seal kit (Check valve) Buna N Viton Viton is a registered trademark of E.I. DuPont Pressure Drop Curves Cartridge only Flow - L/min (,8 cst 49 C) A B Flow - USgpm (05 SUS 0 F) C D Pressure Drop - bar A SPC-0-P-0-00 B SPC-0-P-0-50 C SPC-0-P-0-5 D Port 3 to (piloted open) WARNIN Do not use Single pilot check valves in load holding applications where either overrunning loads are possible; or, load release speed is critical. Failure to observe these guidelines may result in bodily injury or damage to equipment. -8 EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007
29 Model Code SPC-0 SPC 0 (X) P ** *** Function SPC Single pilot check valve Size 0 0 Size 3 Seals Blank Buna-N V Viton U Buna-N with no piston seals W Viton with no piston seals 4 Style P Poppet 5 Port size 0 Cartridge only 6 Free flow cracking pressure 5,7 bar (5 psi) 50 3,45 bar (50 psi) 00 6,90 bar (00 psi) 7 Special Features 00 None (Only required if valve has special features - omitted if 00 ) SS - 36 Stainless Steel external components CODE PORT SIZE HOUSIN NUMBER Aluminum Light duty Aluminum Fatigue rated 3B 3/8 BSPP T SAE /4 BSPP /8 BSPP H SAE H SAE See Section J for housing details. Dimensions mm (inch) 5,4 (.0) hex 8,0 (0.3) Torque cartridge in housing A Nm (35-40 ft. lbs) S Nm (50-55 ft. lbs) Thd. 3 46,8 (.84) Aluminum housings can be used for pressures up to 0 bar (3000 psi) Steel housings must be used for operating pressures above 0 bar (3000 psi) Ø 5,80 (0.63) Ø 7,40 (0.684) EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007-9
30 SPC-0 Single pilot check valve Description The SPC-0 is an in-line housing type, pilot-to-open check valve. Operation This valve allows flow from the valve port to the cylinder port when the spring bias is overcome. Flow is blocked from the cylinder port to the valve port until sufficient pilot pressure is applied at the pilot port. Functional Symbol Cyl. Cyl. Sectional View Pilot Valve Pilot Valve RATINS AND SPECIFICATIONS Performance data is typical with fluid at,8 cst (05 SUS) and 49 C (0 F) Typical application pressure (all ports) 0 bar (3000 psi) Rated flow 45 L/min ( USgpm) Free flow cracking L/min (0.5 USgpm),03 bar (5 psi) Internal leakage cylinder port to valve port 5 drops / min 0 bar (3000 psi) Temperature range 40 to 0 C ( 40 to 48 F) Pilot ratio 4: Fluids All general purpose hydraulic fluids such as: MIL H 5606, SAE 0, SAE 0, etc. Filtration Cleanliness code 8/6/3 Standard housing materials Aluminum Weight 0,5 kg (.4 lb) Seal kit (Check valve) Buna N Viton Seal kit (Pilot piston) Buna N Viton Viton is a registered trademark of E.I.DuPont Pressure Drop - psi Pilot Pressure calculation Nominal pressure to open valve by remote control Pilot pressure at Pilot port = Cracking pressure + Pressure at Cyl port + (0.75 x Pressure at Valve port) 4 Pressure Drop Curves Cartridge only Flow - L/min (,8 c St 49 C) A B Pressure Drop - bar A Valve to Cyl port (Free Flow) B Cyl to Valve port (Piloted Flow) WARNIN Do not use Single pilot check valves in load holding applications where either overrunning loads are possible; or, load release speed is critical. Failure to observe these guidelines may result in bodily injury or damage to equipment Flow - USgpm (05 SUS 0 F) -30 EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007
31 Model Code SPC-0 SPC 0 (S) (V) P ** Function SPC Single pilot check valve Size 0 0 Size 4 Seals 6 Port size 7 Blank Buna-N 3B 3/8 BSPP (Light duty) V Viton 6T SAE 6 (Light duty) 5 Seating type P Poppet Special Features 00 None (Only required if valve has special features - omitted if 00 ) 3 Piston Seals Blank No seals S With seals Dimensions mm (inch) CV-0(V)-P-O-5 Torque cartridge in housing Nm (35-40 ft. lbs) 3,7 (.5) 34,0 (.34) HOUSIN ALL PART PORT SIZE PORTS NUMBER 3B 3/8 BSPP T SAE ,8 (0.63) Cylinder 88,9 (3.50) 7,9 (0.3) 57, (.5) 9, (0.75) 63,5 (.50) 57, (.5) Pilot 3,7 (.5) 3, (0.3) 38, (.50) Valve 7, (0.8) plcs. EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007-3
32 SPC-6 Single pilot check valve Description The SPC-6 is an in-line housing type, pilot-to-open screw-in cartridge type check valve. Operation This valve allows flow from the valve port to the cylinder port when the spring bias is overcome. Flow is blocked from the cylinder port to the valve port until sufficient pilot pressure is applied at the pilot port. Functional Symbol Cyl. Pilot Valve Sectional View Cyl Valve Pilot Pressure Drop - psi RATINS AND SPECIFICATIONS Performance data is typical with fluid at,8 cst (05 SUS) and 49 C (0 F) Typical application pressure (all ports) 0 bar (3000 psi) Rated flow 5 L/min (40 USgpm) Free flow cracking L/min (0.5 USgpm),38 bar (0 psi) Internal leakage cylinder port to valve port 5 drops / min. 0 bar (3000 psi) Temperature range 40 to 0 C ( 40 to 48 F) Pilot ratio 4: Fluids All general purpose hydraulic fluids such as: MIL H 5606, SAE 0, SAE 0, etc. Filtration Cleanliness code 8/6/3 Standard housing materials Aluminum Weight,83 kg (4.03 lb) Seal kit (Check valve) Buna N Viton Seal kit (Pilot piston) Buna N Viton Viton is a registered trademark of E.I.DuPont Pilot Pressure calculation Nominal pressure to open valve by remote control Pilot pressure at Pilot port = Cracking pressure + Pressure at Cyl port Pressure Drop Curves Cartridge only + (0.75 x Pressure at Valve port) Flow - L/min (,8 cst 49 C) Flow - USgpm (05 SUS 0 F) A B Pressure Drop - bar A Valve to Cyl port (Free Flow) B Cyl to Valve port (Piloted Flow) WARNIN Do not use Single pilot check valves in load holding applications where either overrunning loads are possible; or, load release speed is critical. Failure to observe these guidelines may result in bodily injury or damage to equipment. -3 EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007
33 Model Code SPC-6 SPC 6 (S) (V) P *** Function SPC Single pilot check valve Size 6 6 Size 3 Piston Seals Blank No seals S With seals 4 Seals Blank Buna-N V Viton 5 Seating type P Poppet 6 Port size 7 Special Features 6B 3/4 BSPP (Light duty) T SAE (Light duty) 00 None (Only required if valve has special features - omitted if 00 ) Dimensions mm (inch) CV-6(V)-P-O-0 Torque cartridge in housing 08- Nm (80-90 ft. lbs) 50,8 (.00) HOUSIN ALL PART PORT SIZE PORTS NUMBER 6B 3/8 BSPP T SAE ,4 (.00) 88,9 (3.5) Cylinder 7,0 (5.00),7 (0.5) 5,4 (.00) 0,6 (4.00) 9, (3.63) Pilot 50,8 (.00) 4,8 (0.9) 57, (.5) Valve 0,3 (0.4) plcs. EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September,
34 SPC-0 Single pilot check valve Description The SPC-0 is an inline housing type, pilot-to-open check valve. Operation This valve allows flow from the valve port to the cylinder port when the spring bias is overcome. Flow is blocked from the cylinder port to the valve port until sufficient pilot pressure is applied at the pilot port. Functional Symbol Cyl Cyl. Sectional View Pilot Valve RATINS AND SPECIFICATIONS Performance data is typical with fluid at,8 cst (05 SUS) and 49 C (0 F) Typical application pressure (all ports) 0 bar (3000 psi) Rated flow 7 L/min (60 USgpm) Free flow cracking L/min (0.5 USgpm),03 bar (5 psi) Internal leakage cylinder port to valve port 5 drops / min. 0 bar (3000 psi) Temperature range 40 to 0 C ( 40 to 48 F) Pilot ratio 4: Fluids All general purpose hydraulic fluids such as: MIL H 5606, SAE 0, SAE 0, etc. Filtration Cleanliness code 8/6/3 Standard housing materials Aluminum Weight 3,7 kg (6.98 lb) Seal kit (Check valve) Buna N Viton Seal kit (Pilot piston) Buna N Viton Viton is a registered trademark of E.I.DuPont Pilot Pressure calculation Pilot Valve Nominal pressure to open valve by remote control Pilot pressure at Pilot port = Cracking pressure + Pressure at Cyl port + (0.75 x Pressure at Valve port) 4 Pressure Drop Curves Cartridge only Flow - L/min (,8 cst 49 C) Pressure Drop - psi A B Pressure Drop - bar A Valve to Cyl port (Free Flow) B Cyl to Valve port (Piloted Flow) WARNIN Do not use Single pilot check valves in load holding applications where either overrunning loads are possible; or, load release speed is critical. Failure to observe these guidelines may result in bodily injury or damage to equipment. Flow - USgpm (05 SUS 0 F) -34 EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007
35 Model Code SPC-0 SPC 0 (S) (V) P *** Function SPC Single pilot check valve Size 0 0 Size 3 Piston Seals Blank No seals S With seals 4 Seals Blank Buna-N V Viton 5 Seating type P Poppet 6 Port size 7 Special Features 8B BSPP (Light duty) 00 None 6T SAE 6 (Light duty) (Only required if valve has 0T SAE 0 (Light duty) special features - omitted if 00 ) Dimensions mm (inch) CV-0(V)-P-O-5 Torque cartridge in housing 8-55 Nm (95-5 ft. lbs) 63,5 (.50) HOUSIN ALL PART PORT SIZE PORTS NUMBER 8B BSPP T SAE T SAE ,8 (.5) 3,8 (.5),7 (0.5) Cylinder 5,4 (6.00), (4.38) 4,3 (4.50) 0,6 (4,00) Pilot 57, (.5) 6,3 (4.6) 6,3 (0.4) 73.0 (.88) Valve 3,5 (0.53) plcs. EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September,
36 POC-0 Pilot operated check valve Description The POC-0 is a pilot-toopen, screw-in cartridge type check valve. Operation The POC-0 will positively lock a load from port to port, but will release the load by applying pressure to the pilot port (port 3). The load can also be released by adjusting the optional override. Functional Symbols 3 F Type 3 S Type Sectional View RATINS AND SPECIFICATIONS Performance data is typical with fluid at,8 cst (05 SUS) and 49 C (0 F) Typical application pressure (all ports) 350 bar (5000 psi) Cartridge fatigue pressure (infinite life) 30 bar (4500 psi) Rated flow 57 L/min (5 USgpm) Pilot ratio 3: Internal leakage, Port to Less than 5 drops / min. 350 bar (5000 psi) Free flow cracking L/min (0.5 USgpm) 0,3 bar (5 psi);,0 bar (30 psi); 5, bar (75 psi); 6,9 bar (00 psi) Hysteresis less than 3 bar (45 psi) Temperature range 40 to 0 C ( 40 to 48 F) Cavity C 0 3S Fluids All general purpose hydraulic fluids such as: MIL H 5606, SAE 0, SAE 0, etc. Filtration Cleanliness code 8/6/3 Standard housing materials Aluminum or Steel Weight cartridge w/out override 0,0 kg (0.3 lb) cartridge w/override 0,7 kg (0.36 lb) Seal kit Buna-N Viton Viton is a registered trademark of E.I.DuPont 3 Pressure Drop - psi Pressure Drop Curves Cartridge only Flow in L/min (,8 cst 49 C) C 7 D E Flow in USgpm (05 SUS 0 F) 3: Ratio A Pilot pressure, nominal at Port 3 = B (Crack Pressure + Port Pressure - Port Pressure 3 4 Pressure Drop - bar A 00 psi B 75 psi C 30 psi D 5 psi E Full Pilot WARNIN Do not use Pilotto-Open check valves in load holding applications where either overrunning loads are possible; or, load release speed is critical. Failure to observe these guidelines may result in bodily injury or damage to equipment. + Port Pressure -36 EATON Vickers Screw-In Cartridge Valves V-VLOV-MC00-E4 September, 007
Check Valves Valve locator
Check Valves Valve locator Functional Symbol Flow Typical Model Cavity Rating Pressure Page Check valve, direct L/min (USgpm) bar (psi) FPR/4 Inline () 5 (5) - FPR/8 Inline (8) 5 (5) - FPR/ Inline 45 ()
More informationCartridge Valves. Solenoid Valves. Vickers. Screw-in Cartridge Valves. Maximum Pressure 210 bar (3000 psi) Maximum Flow 227 l/min (60 USgpm)
Vickers Cartridge Valves Solenoid Valves Screw-in Cartridge Valves Maximum Pressure bar ( psi) Maximum Flow 7 l/min (6 USgpm) Rev /99 77 Introduction For over seventy years, Vickers has provided its customers
More informationConsolidated Product Manual December 2008. Vickers Screw-in Cartridge Valves
Consolidated Product Manual December 8 Vickers Screw-in Cartridge Valves Solenoid Valves Valve locator Ø -way, - position normally closed Functional Symbol FLOW TYPICL MODEL CVITY RTING PRESSURE PGE Poppet
More information*Rated to 207 Bar/3000 PSI with Aluminum Body. Catalog HY15-3501/US SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO.
Bodies & Contents SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. /GPM BAR/PSI STANDARD CHECKS D1A6... 2U... Valve Insert, Ball Type...145/38... 42/6... 5 D1B125... 2C... Valve Insert, Ball Type... 5/132...
More information*Rated to 207 Bar/3000 PSI with Aluminum Body. Denotes New Winner s Circle Product Line. Catalog HY15-3502/US
Bodies & Contents SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. LPM/GPM BAR/PSI STANDARD CHECKS D1A6... 2U... Valve Insert, Ball Type...145/38... 42/6... 5 D1B125... 2C... Valve Insert, Ball Type...
More informationVickers. Check Valves. Check Valves. Inline, right angle, manifold mounted, and pilot operated designs. Released 9/93
Vickers Check Valves Check Valves Inline, right angle, manifold mounted, and pilot operated designs Released 9/93 645 Introduction Vickers inline, right-angle, and manifold mounted check valves are direct
More informationCatalog HY15-3501/US SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. LPM/GPM BAR/PSI
Bodies & Contents SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. LPM/GPM BAR/PSI KSWA3... SW-3... Ball sert Type...9./2.... 42/6... 3 K2A... 3Z... Poppet sert Type...38/1... 3/... 4 CS41B... C4-3...
More informationSafety for Hydraulics Leak free double check valve, pilot operated, series DERV Cartridge type, two stage
Safety for Hydraulics Leak free double check valve, pilot operated, series Cartridge type, two stage 8 1 1 General description spring closed, pilot operated, cartridge type poppet valve it holds the load
More informationFlow Control Valves. Note: Also see R04C3 on page DC1. Denotes New Winner s Circle Product Line. Catalog HY15-3502/US
Catalog HY15-352/US Contents Control SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. LPM/GPM BAR/PSI NEED VALVES J2A2... C8-2... Needle Valve, Cartridge Type...45/12... 42/6... 5-6 NVH81... C8-2... Needle
More informationSafety for Hydraulics Leak free check valve, pilot operated, series ERV Cartridge type, two stage
Safety for Hydraulics Leak free check valve, pilot operated, series Cartridge type, two stage prevents a load from falling if a burst occurs in feed pipe hardened seat and poppet prevents creep of hydraulically
More informationSolenoid Valves. Poppet and Spool type solenoid actuated valves for applications up to 350 bar (5000 psi) and 227 L/min (60 USgpm) A-1.
Solenoid Valves Poppet and Spool type solenoid actuated valves for applications up to 50 bar (5000 psi) and 7 L/min (60 USgpm) n Eaton rand ETON Screw-In Cartridge Valves E-VLSC-MC00-E November 009 -.
More informationrelief valves 500 Series Adjustable Popoff & Inline Relief Valves 0.5 to 150 psig (10 bar)
Adjustable Popoff & Inline Relief Valves 0.5 to 150 psig (10 bar) How it Works Closed Resilient seal design prevents leakage. Sealing efficiency increase with increased pressure up to cracking pressure.
More informationDenotes New Winner s Circle Product Line. Catalog HY15-3502/US SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. LPM/GPM BAR/PSI HIGH FLOW VALVE FAMILY
Catalog HY-5/US Contents SERIES CAVITY DESCRIPTION FLOW PRESSURE PAGE NO. /GPM BAR/PSI HIGH FLOW VALVE FAMILY See individual catalog pages for exact specifications. WAY SPOOL TYPE GS *... X / C9-.. Position,
More informationPressure Relief. Pressure Control Valve R(C)G(O)-03, 06 and 10; R(C)T(O)-03, 06 and 10 VICKERS. Basic Characteristics. Sectional Illustrations
VICKERS Pressure Relief Pressure Control Valve R(C)G(O)-03, 06 and 10; R(C)T(O)-03, 06 and 10 Sectional Illustrations RCG-** Model Shown RCT-** Model Shown Basic Characteristics Type...................
More informationKDG3V-5/7/8, 10 Series
Vickers roportional Valves KDG3V-5/7/8, 1 Series Single-Stage with Hydraulic ilot Operation High Flow roportional Directional Control Valves asic Characteristics Max. pressure.......... up to 35 bar (5
More informationManapak Sandwich Valves Series CM, CPOM, FM, PRDM, PRM, RM
Introduction Manapak valves provide a variety of check, flow control, pressure relief and pressure reducing functions in a compact NFPA D03, D05 and D08 sandwich style valve. The NFPA D03 valve body conforms
More informationCheck Valves. Pilot Operated Check Valves. Vickers. PCGV-6/8, 10 Series; PCG5V-6/8, 20 Series. Typical Section. Features and Benefits
Vickers Check Valves Pilot Operated Check Valves PCGV-6/8, 10 Series; PCG5V-6/8, 20 Series Typical Section Typical PCG5V model with internally drained pilot piston internal leakage through the closed pilot
More informationChapter 5: Flow Valves
Catalogue HY11-300/UK Contents Chapter : Flow Valves Series Description Size Mounting Page Parker Standard DIN / ISO 1/4 3/8 1/2 3/4 1 06 10 16 Throttle valves, manual adjustment MVI -2 NS -4 FS With free
More informationQ Series Piston Pumps Variable Displacement, Quiet Series for Industrial Applications
Q Series Piston Pumps Variable Displacement, Quiet Series for Industrial Applications Technical Catalog PVQ10 PVQ13 PVQ20 PVQ25 PVQ32 PVQ40 PVQ45 Table of Contents Introduction......................................................................................................
More informationPressure Relief and Regulating Valves
Pressure Relief and Regulating Valves With blocked center directional valves and variable displacement pumps, or open center directional valves and fixed displacement pumps where fast response, low leakage
More information3/2- and 2/2-way cartridge valve type BVE
3/2- and 2/2-way cartridge valve type BVE for any flow direction, zero leakage, all ports pressure resistant Flow Q max = 70 lpm Perm. pressure p max = 400 bar Additional valves with same function: ' Type
More informationPVH131/141 Variable Displacement Piston Pump - 11 Design
Service Data Vickers Piston Pumps PVH131/141 Variable Displacement Piston Pump - 11 Design Revised 05/01/97 M-2209-S Maximum Adjustable Stop S Option 913341 Locknut Torque 25-50 N.m. (18-37 lb. ft.) Torque
More informationCOUNTERBALANCE VALVES
COUNTERBALANCE VALVES Introduction They are modulating valves which allow free flow into the actuator and then block the reverse flow until they feel a pilot pressure inversely proportional to the load
More informationPVQ 40-B2/M2 * *** - ** * * - 10 C** *** *** * - 10/11/12/20 PVQ 45-B2/M2 * *** - ** * * - 10 C**
Service Data Vickers Piston Pumps Low Noise Industrial Piston Pump PVQ 40-B2/M2 * *** - ** * * - 10 C** *** *** * - 10/11/12/20 PVQ 45-B2/M2 * *** - ** * * - 10 C** *** *** * - 10/11/12/20 C, CM Compensator
More informationFIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES
BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps. All the components subject to wear are contained
More informationFIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES
BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps. All the components subject to wear are contained
More informationFIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES
BQ FIXED DISPLACEMENT HYDRAULIC VANE PUMPS BQ SERIES Versatility, power, compactness and low running costs are the main characteristics of B&C vane pumps. All the components subject to wear are contained
More informationChapter 6: Check Valves
Contents Chapter : Check Valves Series Description Size Mounting Page Parker Standard DIN / ISO 1/8 1/4 3/8 1/2 3/4 1 0 10 1 25 32 Shuttle valves SSR -2 Check valves, direct operated RK / R CS SPZE SPV
More informationSeries PVP Variable Volume Piston Pumps
Series PVP Variable Volume Piston Pumps Catalog HY28-2662-CD/US Revised June, 212 hpm12-1.p65, lw, jk 1 Notes Series PVP hpm12-1.p65, lw, jk 2 Introduction Series PVP Series Sizes 6-14 Phased Out For Reference
More informationMaterial taken from Fluid Power Circuits and Controls, John S. Cundiff, 2001
Pressure Control Chapter 3 Material taken from Fluid Power Circuits and Controls, John S. Cundiff, 2001 Introduction Pressure control is a key element in the design of any circuit. Used correctly, it can
More informationHYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS
HYDRAULIC COMPONENTS HYDROSTATIC TRANSMISSIONS Hydraulic components POCLAIN HYDRAULICS Methodology : This document is intended for manufacturers of machines that incorporate Poclain Hydraulics products.
More informationVariable Displacement Pump AA10VSO
Variable Displacement Pump AA10VSO Series 31, Industrial Model, for Open Circuits Axial piston, swashplate design Brueninghaus Hydromatik Sizes 28...140 Nominal pressure 4000 psi Peak pressure 5100 psi
More informationE4E PILOT OPERATED DIRECTIONAL CONTROL VALVE WITH ELECTRIC PROPORTIONAL CONTROL SERIES 51
83 300/100 ED E4E PILOT OPERATED DIRECTIONAL CONTROL VALVE WITH ELECTRIC PROPORTIONAL CONTROL SUBPLATE MOUNTING CETOP P05 p max 250 bar Q max (see specification table) MOUNTING INTERFACE OPERATING PRINCIPLE
More information3/2 Solenoid Cartridge Valve, Size 6
/ Solenoid Cartridge Valve, Size 6 Q max = l/min, p max = 5 bar Bidirectional seat-valve shut-off, direct acting Guided valve spool and poppet Two spool variants are available Available in two mounting
More informationLine rupture protection valves type LB
Line rupture protection valves type LB Pressure p max Flow rate Q A max = 500 bar = 4... 160 lpm Screw-in versions Type LB...C In-line versions Type LB...G Type LB...F 1. General Line rupture protection
More informationPressure relief valves Size 6
Pressure relief valves Size 6 direct controlled Interface to DIN 24 340 and ISO 6264 PN [p max. ] = bar 750400.06.0.06 Description (standard units) Design The pressure relief valves of Type D B C 6 are
More information15/40/80CN Series Medium Pressure Filters
1/4/8CN Series Medium Pressure Filters Max 32 l/min - 7 bar Global Filtration Technology 1/4/8CN Series TYPICAL APPLICATIONS Compressor Lube Oil Off-line Filter Loops Machine Tools (Automotive Standard)
More information2011 DC Electropumps Bull. Rotation Ø 15 6,45 3,5 5,7
Ø 5 ±. DC Electropumps Bull,5 Rotation,5 5,7 Email: sales@hydronit.com Fax B... Electro pumps Bull series MODEL CODE EPB,5 DC /S5 K, V** Electro Pump Bull series Gear pump displacement (cc/rev (see tables
More informationHydraulic Flow Control Valves
Webtec Products Limited Hydraulic Flow Control Valves Quality Hydraulic Components from the Webtec Range CONTENTS DESCRIPTION PAGE No. ILFC Series Fixed Flow Pressure Compensated Control Valve 1 VFC Series
More informationOildyne. 165 Series Hydraulic Power Units. Pressures to 241 bar (3500 psi) Flows to 5.4 lpm (1.4 gpm)
Oildyne Hydraulic Power Units Pressures to 241 bar (3500 psi) Flows to 5.4 lpm (1.4 gpm) 11 Power Unit Features We are pleased to introduce our new power units. The power units let you put more power where
More information3-Way heavy duty flow control, with pressure compensated and solenoid controlled priority flow
1/6 RE 18309-3/06.10 Replaces: RE 18309-3/04.10 3-Way heavy duty flow control, with pressure compensated and solenoid controlled priority flow A-VRFC3C-VEI-VS 0M.43.20.80 - Y - Z Description The flow control
More informationSteering unit. Table of contents. Features RE 11872/05.06. Type LAGL. Frame sizes 500 to 1000 Component series 1X Maximum flow 80 l/min
Steering unit RE 11872/05.06 /10 Type LAGL Frame sizes 500 to 1000 Component series 1X Maximum flow 80 l/min H7375 Table of contents Contents Page Features 1 Ordering code 2 Function, section 3 Device
More information2-Way heavy duty flow control, with pressure compensated, solenoid and load sensing controlled priority flow
2-Way heavy duty flow control, with pressure compensated, solenoid and load sensing controlled priority flow RE 18309-64/04.10 1/6 Replaces: RE 00171/02.07 A-VRFC2C-VEI-VS-LS 0M.28.03.80 - Y - Z Description
More information2/2 and 3/2 Way Size 6 Seat Valves
2/2 and 3/2 Way Size 6 Seat Valves Directly operated Interface and subplate dimensions according to DIN 24340 and ISO Line connection port size G 3/8" Cartridge design PN [p max. ] = 315 bar 7501856.06.12.08
More informationRated Burst Pressure 200 Series: 2.5 : 1 H200 Series: 4 : 1
200 Series 0 to 3000 psig heck Valves H200 Series 0 to 6000 psig heck Valves Features & enefits Quick opening/positive closing Provides a wide range of adaptability Large flow capacity The patented sealing
More informationVARIABLE DISPLACEMENT AXIAL PISTON PUMPS. For truck applications
VARIABLE DISPLACEMENT AXIAL PISTON PUMPS For truck applications TVP FEATURES Variable displacement axial piston pumps swash plate design ideally suited for open circuit truck applications. The compact
More informationVickers. Piston Pumps
Vickers Piston Pumps xial Piston Pumps Fixed and Variable Displacement PF, PF, PF PV /6, PV /, PV /9, PV and PV 9 to SE PV /6, PV /, PV /9 to DIN/ISO 39, Part G-379 Contents asic characteristicts..........................................................................................3
More informationSystemStak. SystemStak Valves. Vickers
Vickers SystemStak SystemStak Valves ISO 4401-05 size, 315 bar (40 psi) and 120 l/min (32 USgpm) maximum ratings ressure relief and reducing, sequence, counterbalance, and flow control functions Revised
More informationPrecision Solenoid Valves
Precision Solenoid Valves Solenoid Valves for gas General Purpose Valves Specialty Solenoid Valves n Didn t see what you re looking for? Let us review your requirements and chances are we can help solve
More informationSeries TMM Axial Piston Motor. Technical Information
Series TMM Axial Piston Motor Technical Information General Description GENERAL DESCRIPTION These motors are designed primarily to be combined with other products in closed circuit systems to transfer
More informationPILOT OPERATED PRESSURE RELIEF VALVE - Series VR4V
PILOT OPERTED PRESSURE RELIEF VLVE - Series VR4V The Veljan Pressure Relief Valve series VR4V are pilot operated and wk Internal Dra on the prciple of hydraulic balancg. These valves are used to limit
More informationPVM Piston Pumps Service Manual
PVM Piston Pumps Service Manual PVM018/020 PVM045/050 PVM057/063 PVM074/081 PVM098/106 PVM131/141 Table of Contents Service Parts Pump Description... 3 Basic pump Pump Operation Controls Types Part Identification...
More informationThe Eaton Advantage. machinery using accumulators.
Accumulators Table of Contents The EATON Advantage................................................................................. 3 Application Benefits...................................................................................
More informationVHO/VQ Single, Double & Triple Vane Pumps
VHO/VQ Single, Double & Triple Vane Pumps Series Available: 20, 25, 30, 35, 45, 50 For Mobile and Industrial Use Cartridge Kits Available for All Sizes Same Day Shipments www.fluidynefp.com Our People
More informationPressure Relief. Pressure Relief Valves. Vickers
Vickers Pressure Relief Pressure Relief Valves Remote Controls, Relief and Sequence Valves, and Single and Multiple Pressure Solenoid and Air Operated Relief Valves 511./EN/1297/A Introduction Remote Controls
More informationHydraulic Pump/Motor Division Hydraulic Pump/Motor Division
Parker Piston Pumps Otsego Core Competency... Piston Pumps PAVC Series : 4 displacements from 33-100 cc/r, 207 Bar, 3000 RPM PVP Series : 9 displacements from 16-140 cc/r, 250 Bar, 3000 RPM PV Plus : 12
More informationRPE3-04. Functional Description HA 4014 10/2010. Directional Control Valves Solenoid Operated. Replaces HA 4014 12/2007
Directional Control Valves Solenoid Operated RPE3-04 Size D 04 (02) 320 bar (4600 PSI) 30 L/min(8.0 GPM) HA 4014 10/2010 Replaces HA 4014 12/2007 4/3-, 4/2- way directional control valves with solenoid
More informationPiston Accumulators. SK Series. Accumulator Catalog. Piston Types. Description. Sealing Systems. End Cap. O-ring. Sealing System. Piston.
SK Series Piston Types TYPE 2 pplication: Low-friction design for higher piston speeds, slow movements without stick-slip effect and high number of actuations (millions). ctual cycles achieved will vary
More informationPART 2 FORKLIFT HYDRAULIC SYSTEM
PART 2 FORKLIFT HYDRAULIC SYSTEM Chapter 1 Description and Operation Component Locations & Circuit Layouts 1 Hydraulic Pump 11 Control Valve 14 Valve Section Oil Flows 15 Anti-Cavitation Valve 22 Velocity
More informationPressure Relief. Pressure Relief and Sequence Valves CG2V-6/8, 10 Series; CG5V-6/8, 20 Series. Vickers. Features and Benefits.
Vickers Pressure Relief Pressure Relief and Sequence Valves CG2V-6/8, 1 Series; CG5V-6/8, 2 Series Typical Section CG2V-6*W-1 relief valve Basic Characteristics Maximum pressure.......... 35 bar (5 psi)
More informationMONO BLOCK DIRECTIONAL CONTROL VALVE TS1120TSLB
MONO BLOCK DIRECTIONAL CONTROL VALVE TS112TSLB TS TS212TSTSJB P T TS312TSDTSTKJ TS112TSJB FEATURES: O RG PORTS to eliminate leakage. POWER BEYOND CAPABILITY to fit your multi valve circuits. BUILT ANTI-DROP
More informationV47 Series Temperature Actuated Modulating Water Valves
V47 Series Temperature Actuated Modulating Water Valves Master Catalog 125 Valves, Miscellaneous (Other Than Gas) Section V Product Bulletin V47 Issue Date 0286 Application The V47 modulating valves regulate
More informationVickers. Valves. CM2, CM11, RM3 & FM3 Control Valves. For Mobile Equipment. Revised 4/96
Vickers Valves CM2, CM11, RM3 & FM3 Control Valves For Mobile Equipment Revised 4/96 33 Introduction The directional valves described in this booklet are more than just directional valves -- they are hydraulic
More informationPressure Relief Valves SPV, SPVF
Pressure Relief Valves SPV, SPVF Construction of the Pressure Relief Valves SPV, SPVF Symbol Description The direct spring, sliding piston Pressure Relief Valve SPV/SPVF is intended for inline mounting
More informationFluid. Flu. Fluid Fluid. uid Power d Power P. Fluid Power P. Fluid Power. Fluid Power Power. d Power. Directional Cetop Valves DCV 03.
Catalogue Directional Cetop Valves DCV 03 Power Flu uid Power d Power P wer Power Power Power Power Power d Power Power Power ower Power Power wer Power Power P Power Power Powe d Power Power Power Power
More informationBulletin 2537-M4/USA Service Bulletin Series CPOM
Service Bulletin Series CPOM Effective: November 11, 1996 WARNING FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED ITEMS CAN CAUSE DEATH, PERSONAL
More informationFDH Series Compact Finger Slides
FDH Series Compact Finger Slides Catalog #FDH- Prices effective September 1, 11 Cylinder block- Clear anodized aluminum Top Toolplate and Front Toolbar Clear anodized aluminum Tapped mounting holes ( for
More informationPneumatic Grippers Parallel and Angular Grippers. Catalog 1900-2/US
Pneumatic Grippers Parallel and Angular Grippers Catalog 19-2/US Catalog 19-2/US OContents GPR Series Rotary vane driven design GPR GPCR Series P5G-HPM(C) Series P5G-HP Series GPT Series P5G-AP Series
More informationTable of Contents. M Series Variable Displacement Piston Pumps
Table of Contents M Series Variable Displacement Piston Pumps Introduction.... 3 Hydraulic System Design Calculations.... 4 Model Code Selection.... 5 Model Code Options.... 6 Specifications and Performance...
More informationIMPORTANT DOCUMENTATION DO NOT DISCARD!
PART NO.: 6441-263C SERIES GRT 3 JAW PARALLEL GRIPPERS INFORMATION SHEET IMPORTANT DOCUMENTATION DO NOT DISCARD! Use this information sheet to assist with gripper installation and setup. File with maintenance
More informationFlow divider (flow distributor), type TQ
Flow divider (flow distributor), type TQ Pressure p max = 0 bar Flow Q CN max = 00 lpm Share ratio = :. General Task Flow dividers type TQ are self-regulating valves, which largely irrespective of the
More informationPressure reducing valve, direct operated, Type ZDR 6 D
RE 26 57/2.3 Replaces:.2 Pressure reducing valve, direct operated, ype ZDR 6 D Nominal size 6 Series 4X aximum operating pressure 2 bar aximum flow 5 L/min K 4279/ ype ZDR 6 DP2 4X/ Y Overview of contents
More informationUnit 24: Applications of Pneumatics and Hydraulics
Unit 24: Applications of Pneumatics and Hydraulics Unit code: J/601/1496 QCF level: 4 Credit value: 15 OUTCOME 2 TUTORIAL 4 DIRECTIONAL CONTROL VALVES The material needed for outcome 2 is very extensive
More informationCheck Valves, Flow Control and Priority Flow Control Valves
Check Valves, Flow Control and Priority Flow Control Valves Applications Sun check valves provide non-modulating on/off control, and Sun flow control valves provide flow modulation for control of metering
More information"A" Series Variable Displacement Piston Pumps Single Pump, "OBE" Type Electro-Hydraulic Proportional Pressure & Flow Control Type
Single Pump, "OBE" Type Electro-Hydraulic Proportional & Flow Type Input Signal for Safety valve Input Signal for Flow Amplifier Proportional Solenoid Sensor Valve Piston (S Input Voltage L) Performance
More informationSeries PAVC Variable Displacement Piston Pumps zp01. Catalog HY28-2662-CD/US
Series PAVC Variable Displacement Piston Pumps zp1 Catalog HY28-2662-CD/US 1 Introduction Series PAVC Quick Reference Data Chart Pump Model Displacement CM 3 /REV (IN 3 /REV) Pump Delivery *Approx. Noise
More informationD660 Series Servo-Proportional Control Valves with Integrated Electronics ISO 4401 Size 05 to 10
D660 Series Servo-Proportional Control Valves with Integrated Electronics ISO 4401 Size 05 to 10 OVERVIEW D660 Section Page MOOG SERVO-PROPORTIONAL CONTROL VALVES Overview 2 3 Technical Data 4 5 Electronics
More informationSOLENOID VALVES 3-4 WAY
SOLENOID VLVES - WY IE/C// CT: FP/VCR Page: 7 SHEET: / SOLENOID VLVES - - WY CV SOLENOID VLVES -WY/-POSITION /- UNF.7 5.7 The electric valve is a -way -position directional electrically controlled Slight
More informationExample. Fluid Power. Circuits
Example Fluid Power Circuits To Enhance Symbol Reading Skills To Work On Circuit Reading Skills With Answers HI LO Pump Circuit 18 A1 B1 17 16 15 13 Set 14 2,000 PSI PG2 Set 500 PSI 12 11 7 8 10 PG1 9
More informationSCP 012-130 ISO. Other advantages: SCP 012-130 ISO is a series of piston pumps with a fixed displacement for mobile and stationary hydraulics.
SCP 012-130 ISO is a series of piston pumps with a fixed displacement for mobile and stationary hydraulics. SCP 012-130 ISO covers the entire displacement range 12-130 cmᶟ rev. at a maximum pressure of
More informationDual Path Mobile Pump
Dual Path Mobile Pump Technical Manual 350 Series 350 Series Mobile Pump Introduction Single Assembly* Dual Path Assembly The 350 Series mobile pump is an advanced, closed circuit, servo controlled, axial
More informationTypical Aluminum GFM Mass Flow Meter
MASS FLOW METERS Design Features n Rigid metallic construction. n Maximum pressure of 1000 psig (70 bars). n Leak integrity 1 x 10-9 of helium. n NIST traceable certification. n Built-in tiltable LCD readout.
More informationPipe Valves, Fittings and Nipples Pressures to 15,200 psi
Pipe Valves, Fittings and Nipples MAXIMATOR has been designing and manufacturing high pressure equipment for more than thirty years and has a worldwide reputation for quality and reliability, backed by
More informationDirectional Controls. Solenoid Operated Directional Valve DG4V-3S, EN 490 For Mobile Equipment
Vickers Directional Controls Solenoid Operated Directional Valve DGV-3S, EN 90 For Mobile Equipment Flows to 0 l/min (10.5 USgpm), * Design P, A & B Pressures to 350 bar (5000 psi), T Pressures to 10 bar
More information15/40/80CN Series Coreless Medium Pressure Filters
//8CN Series Coreless Medium Pressure Filters //8CN Series Applications Compressor Lube Oil Off-line Filter Loops Machine Tools (Automotive Standard) Hydrostatic Drive Charge Pumps Mobile Equipment Pilot
More informationTable of Contents. Overview 1. Pump Disassembly 2. Control Disassembly / Reassembly 7. Pump Reassembly 13. Adjustment Procedures DR Control 19
Table of Contents Overview 1 Pump Disassembly 2 Control Disassembly / Reassembly 7 Pump Reassembly 13 Adjustment Procedures DR Control 19 Adjustment Procedures DRG Control 20 Adjustment Procedures DFR
More informationE08 E10. Compact Excavators
E08 E10 Compact Excavators E08 Micro-Excavator Retractable undercarriage and blade Foldable TOPS structure Built-in operator safety Compact dimensions Cylinder-over-the-boom design Optional Demolition
More informationConsolidated Product Manual December 2008. Screw-in Cartridge Valves
Consolidated Product Manual December 8 Screw-in Cartridge Valves abc INTRODUCTION QUICK SELECTION GUIDE RELIEF VALVES DUAL RELIEF VALVES SEQUENCE VALVES PRESSURE REDUCING VALVES MOTION CONTROL VALVES including
More informationVickers PVM Piston Pumps
Vickers PVM Piston Pumps 18-141cc 3 (1.1-8.6in 3 ) M-Series Industrial Variable Displacement M-Series Mobile Variable Displacement Table of Contents M Series Variable Displacement Piston Pumps Principles
More informationDirect Operated Regulator for 6.0 MPa (Relieving Type) How to Order. Body size 30 40
Direct Operated Regulator for (Relieving Type) Series Service life: 0 million cycles Using NSF-H-certified grease on the guide ring (sliding) part. Improved durability under a high environment with a polyurethane
More informationWILROY. Operation. Optional Diaphragm Rupture Detection HYDRAULICALLY ACTUATED DIAPHRAGM PUMP
WILROY ATEX Approved HYDRAULICALLY ACTUATED DIAPHRAGM PUMP Williams and Milton Roy have combined technologies to design a pump blending the proven mroy hydraulic by-pass diaphragm design with the Williams
More informationEco130 Series. Medium Pressure Filters Max. 1400 l/min. 30 bar. Modular system for industrial applications. Applications: Contact Information:
Eco130 Series Medium Pressure Filters Max. 1400 l/min. 30 bar Modular system for industrial applications High flow return filters for industrial use on hydraulic or lubrication systems. High flow and pressure
More informationBaumann 24000 Little Scotty Bronze Control Valve
24000 Valve Product Bulletin Baumann 24000 Little Scotty Bronze Control Valve Baumann Little Scotty industrial control valves are intended for general utility service in pressure, flow, and temperature
More informationHi-Cyclic. 2, 3 and 4-Way Directional Control Valves for Pneumatic and Hydraulic Service
Catalog LX-325 Hi-Cyclic 2, 3 and 4-Way Directional Control Valves for Pneumatic and Hydraulic Service FEATURES: Manual, Pilot, Solenoid or Mechanical Operators Two and three position models Many types
More informationUSA Headquarters. Dynex/Rivett Inc. 770 Capitol Drive Pewaukee, WI 53072 U.S.A. Tel: 262-691-2222 FAX: 262-691-0312 E-mail: sales@dynexhydraulics.
SPECIFICATIONS PF1000 Series Fixed Displacement Pumps Also refer to "Checkball Pump Installation and Operating Recommendations" Bulletin PSI.CB (dynexpumpinstallation.pdf) CONTACT INFORMATION USA Headquarters
More informationKF Needle & Gauge Valves
KF Needle & Gauge Valves Superior Fluid Control Products KF O-Ring & Packed Stem Style Needle Valves KF Needle Valves combine rugged construction, dependability and leak-free performance at high and low
More informationVickers. Overhaul Manual. Relief Valves. Balanced Piston Relief Valves. CG/CS/CS5-03/06/10 Series CT/CT5/CG5-06/10 Series
Overhaul Manual Vickers Relief Valves Balanced Piston Relief Valves CG/CS/CS5-03/06/10 Series CT/CT5/CG5-06/10 Series Revised 1/1/85 I-3300-S Table of Contents Section Page I. Introduction.......................................................................................
More informationP2/P3 Series Piston Pumps Variable Displacement zp09. Catalog HY28-2662-CD/US
P2/P3 Series Piston Pumps Variable Displacement zp9 Catalog HY28-2662-CD/US A3 Series P2/P3 A4 General Information General Information Series P2/P3 P2 Series The newly developed variable displacement piston
More informationPRESSURE REDUCER AND RELIEF VALVES WITH METALLIC BELLOW FOR WATER STEAM
PRESSURE REDUCER AND RELIEF VALVES WITH METALLIC BELLOW FOR WATER STEAM PRESSURE REDUCER AND RELIEF VALVES These devices are used to reduce and control a gaseous flow pressure (air, steam, gas ). The PRESSURE
More informationball valves Flomite 71 Series 2-way Integral Panel Mount Ball Valves
2-way Integral Panel Mount Ball Valves Used for quick on-off service with a visual indication of flow, HOKE s 2-way ball valves offer orifice sizes up to 0.25 (6.4mm). Flomite valves feature a floating
More information