MANUAL. Competence in Functional Safety. Solenoid valves for safety-instrumented systems functional principle and typical applications

Transcription

1 MANUAL Manual Competence in Functional Safety functional principle and typical applications Binary converters Diaphragms Applications SMART IN FLOW CONTROL.

2 SAMSON AIR TORQUE CERA SYSTEM KT-ELEKTRONIK LEUSCH PFEIFFER RINGO SAMSOMATIC STARLINE VETEC Founded in 1907, SAMSON has since become a worldwide leader in the manufacture of expertly engineered control valves. SAMSON has over 50 subsidiaries, amongst them noted manufacturers of special valves. With these subsidiaries, SAMSON is represented in over 80 countries to assist its customers on all continents. 2

3 Contents 1 Scope What makes SAMSOMATIC solenoid valves superior?...4 Functional principle of the electropneumatic binary converter Functional principle of solenoid valves with diaphragms Applications Air purging of the actuator spring chamber to protect the actuator springs against corrosion Emergency venting of an actuator Venting an actuator when the supply pressure falls below a minimum pressure Switching to a backup buffer tank when the air supply fails Reliable fail-safe action of actuators Reliable fail-safe action of actuators with pressure monitoring Appendix: Certificate...1

4 1 Scope In safety-instrumented systems, pneumatic valves are used to shut off or open pipelines. Solenoid valves are the interface between the electric control level and the pneumatic actuator. SAMSOMATIC has been active in developing and manufacturing solenoid valves with a high reliability at a low power consumption for many years. The solenoid valves meet the highest quality requirements and are suitable for use in safety-instrumented systems up to SIL according to IEC 61511, up to SIL 4 according to IEC as well as PL e according to ISO What makes SAMSOMATIC solenoid valves superior? 1. Solenoid valves with diaphragms are preferably used in safety-instrumented systems. The decisive advantage provided by diaphragms is that the solenoid valves operate reliably on demand and move the valve to the failsafe position even after the solenoid valves have remained static for long periods of time or when the booster valves are slightly clogged with dirt. 2. An electropneumatic binary converter, which has proven reliable in service a million times over, working together with a flapper/nozzle system, guarantees reliable switching even after it has remained static for long periods of time.. By constantly purging the electronics compartment with instrument air, the solenoid valves are protected against corrosion even when installed in damp or aggressive environments. 4. All solenoid valves are subjected to function and leak tests, minimizing the probability of failure on demand due to defective components or leaks. 4

5 Functional principle of the electropneumatic binary converter The electropneumatic binary converter is supplied with a constant supply pressure of 1.4 bar. In the idle position, the flapper (2) is lifted off the outlet nozzle () by the spring (4), allowing a small rate of air to flow through the outlet nozzle into the electronics compartment. This causes the pressure in the system to drop to a level at which the downstream booster valve is not activated (refer to section 4). When the solenoid coil (1) is energized by an electric binary signal, the magnetic field causes the flapper (2) to be pushed downwards against the force of the spring (4) and the outlet nozzle () to be closed. As a result, the pressure in the system rises and the booster valve is switched to the operating position. When the electric binary signal is deactivated, the booster valve is switched to the idle position again by the spring (4). Advantages of the flapper/nozzle system Reliable switching even after remaining static for long periods of time No memory effect, as occurs in piezo elements for example Switching behavior independent of the mounting position Long service life (over 20 million switching cycles) Low power consumption thanks to frictionless bearing of the flapper Outlet nozzle () Spring (4) Flapper (2) Solenoid coil (1) Nominal signal AC/DC 1.4 bar supply air Downstream booster valve 5

6 4 Functional principle of solenoid valves with diaphragms The solenoid valves consist of an electropneumatic binary converter (refer to section ) and a booster valve with return spring. The supply pressure is applied to connection 4. Connection is routed to the actuator. The actuator is vented over connection 5. The air supply for the electropneumatic binary converter is routed internally through connection 4 at the booster valve. Connection 9 is sealed by a blanking plug. The pressure reducer (5) reduces the supply air pressure to 1.4 bar. In the idle position, the flapper (2) is lifted off the outlet nozzle () by the spring (4). This causes a pressure lower than the switch-on pressure of the booster valve to build up in the pressure divider, which consists of the restrictor (6) and outlet nozzle (). When the solenoid coil (1) is energized by an electric binary signal, the outlet nozzle () is closed by the flapper (2) against the force of the spring (4). This causes the pressure in the pressure divider to rise above the switch-on pressure of the booster valve, switching it to the operating position. After the solenoid coil is de-energized, the booster valve is switched to the idle position again by the return spring (7). The solenoid valve can be converted to accept an external air supply at connection 9 by turning a flat gasket on the enclosure. This is necessary when the solenoid valve is mounted onto an actuator for modulating service and a constant control pressure of at least 1.4 bar must be guaranteed at the electropneumatic binary converter. Outlet nozzle () Spring (4) Electropneumatic binary converter Flapper (2) Solenoid coil (1) Nominal signal AC/DC Pressure reducer (5) 9 Changeover to external supply Restrictor (6) Exhaust air /2-way booster valve with return spring 5 4 Supply air/ internal supply Return spring (7) Output to actuator Breather function of spring chamber 6

7 5 Applications 5.1 Air purging of the actuator spring chamber to protect the actuator springs against corrosion Task In safety-instrumented systems, valves often remain static in one position for long periods of time. During this time, the actuator springs are at risk of corroding if moisture enters the actuator. Solution using a Type 967 Solenoid Valve The electronics compartment of the solenoid valve is constantly purged with instrument air through the flapper/nozzle system (refer to section ). This air purging is also guaranteed when the solenoid valve is energized. The electronics compartment is directly connected to the actuator s spring chamber over the NAMUR interface. The solenoid valve is vented at the enclosure cover by a filter check valve (with IP 65 degree of protection), which opens at a defined excess pressure. As a result, a minimal level of positive pressure constantly exists in the electronics compartment and the actuator spring chamber, preventing moisture from entering the spring chamber and inhibiting corrosion. Rotary actuator with Type 967 Solenoid Valve 2 Venting on the enclosure cover 9 1 Air purging of the actuator spring chamber Supply air/internal supply External supply 7

8 5.2 Emergency venting of an actuator Task In the event of failure, an actuator is to be vented independent of the control signal. Solution The actuator is often controlled by a positioner (A) and a solenoid valve (C) in a process control system. When the solenoid valve (C) is energized, the output of the pneumatic booster (B) is connected to the actuator. The pneumatic booster (B) supplies the actuator with an air flow output whose pressure corresponds exactly to the signal pressure, except that it has a much higher volume. This increases the positioning speed even of large pneumatic actuators. In the event of failure, the electric power supply is cut off by the process control system and the solenoid valve (C) is switched to the fail-safe position. The actuator is vented independent of the output of the positioner (A) and pneumatic booster (B). This solution can also be implemented for small actuators without a pneumatic booster (B). A SIG B C IN OUT A SAMSON Type 70- Positioner B SAMSON Type 755 Pneumatic Booster C SAMSOMATIC solenoid valve (e.g. Type ) 8

9 5. Venting an actuator when the supply pressure falls below a minimum pressure Task If the supply pressure level falls below a certain pressure, the actuator is to be vented and the valve moved to its fail-safe position. Solution using a solenoid valve and an electric pressure monitor or pressure limiter In normal operation, the actuator is controlled by a positioner together with a solenoid valve (A). The supply pressure is constantly monitored by an electric pressure monitor (B). When the supply pressure falls below a certain minimum pressure, the electric power supply is automatically cut off and the solenoid valve (A) is switched to fail-safe position. The actuator is vented as a result. The electric signal is not reactivated immediately after the supply pressure increases again due to the hysteresis of the pressure monitor (B). An electric pressure limiter with internal interlock can also be used instead of the electric pressure monitor. In this case, the electric signal must be reactivated manually. This solution can also be implemented for rotary actuators and on/off valves. B E P A p V DC A SAMSOMATIC solenoid valve (e.g. Type ) B SAMSOMATIC Type DWR-6 Electric Pressure Monitor, or alternatively Type DWR Electric Pressure Limiter with internal interlock (adjustment range between 0.5 and 6 bar) 9

10 5.4 Switching to a backup buffer tank when the air supply fails Task After a supply air failure, the position of an on/off valve is to be maintained for a certain period of time. Solution using a buffer tank for instrument air In normal operation, the actuator is filled with air or vented by a solenoid valve (A) according to the process requirements. The required instrument air is supplied by a main supply air station. In the event that this air station fails, the air supply is maintained by a backup buffer tank (B), which provides the solenoid valve (A) with instrument air. The continued operation of an on/off valve over a certain period can be guaranteed in this way. This allows repairs to be performed on the supply air station while the process is running or the plant to be shut down safely. The supply pressure can be monitored by an electric pressure monitor (e.g. Type DWR-6, not shown in the diagram) to signal when the pressure falls below a certain limit A E P D C B A SAMSOMATIC solenoid valve (e.g. Type ) B Buffer tank (sized according to customer requirements) C Check valve D Safety valve 10

11 5.5 Reliable fail-safe action of actuators Task To achieve better reliability and possibly also a higher level of safety (SIL or PL) in safety-instrumented systems, the solenoid valves must be designed in a redundant configuration. In this way, if one solenoid valve fails, the fail-safe action of the actuator is still guaranteed by a second solenoid valve. A hook-up of the solenoid valves in series or in parallel is used depending on the safety requirements. This usually involves complex hook-ups. Solution using a redundancy plate A redundancy plate allows two solenoid valves to be connected in series or in parallel without any additional hook-up. The solenoid valves are mounted either on the left or right side to the NAMUR interfaces of the redundancy plate. The redundancy plate can be directly attached to rotary actuators over a third NAMUR interface. An additional adapter plate also allows a hook-up using threaded connections or the attachment of the solenoid valves to linear actuators with a NAMUR rib. Advantages of the redundancy plate Easy and quick mounting Compact design Captive fastening screws Body made of powder-coated aluminum or stainless steel G or NPT threaded connections Attachment to rotary actuators with NAMUR interface according to VDI/VDE 845 Attachment to linear actuators with NAMUR rib according to IEC Reliable fail-safe action to vent the actuator V1 V2 9 9 Reliable fail-safe action to fill the actuator with air V1 V

12 5.6 Reliable fail-safe action of actuators with pressure monitoring Task To achieve better reliability and possibly also a higher level of safety (SIL or PL) in safety-instrumented systems, the solenoid valves must be designed in a redundant configuration. In this way, if one solenoid valve fails, the fail-safe action of the actuator is still guaranteed by a second solenoid valve. However, it is not possible to identify which solenoid valve has failed without pressure monitoring. Solution using integrated pressure switches The output pressure of the solenoid valves is constantly monitored by two integrated pressure switches. If an energized solenoid valve does not produce the minimum output pressure, an electric contact indicates this failure, for example to the process control system. This not only allows the detection of a faulty solenoid valve, but enables the switching functions to be tested while the process is running, without changing the position of the process valve. 12

13 6 Appendix: Certificates Certificate no. V 60.09/14 Rev. 01 Types 701, 96 and 967 Solenoid Valves with safety function Suitable for use in safety-instrumented systems 1

14 14

15 15

16 Manual Competence in Functional Safety Production sites Subsidiaries SAMSOMATIC GMBH Weismuellerstrasse Frankfurt am Main, Germany Phone: Fax: samsomatic@samsomatic.de Internet: WA 270 EN