Medium Pressure Filters. 15/40/80CN Series. MAX 600 I/min - 70 bar FEATURING. Medium pressure filters

Transcription

1 1/4/8CN Series MAX I/min - 7 bar FEATURING 73 Medium pressure filters

2 1/4/8CN Series Features & Benefits Features bar fatigue rating (eight times that of a spin-on) Diametral (side) seal between head and bowl Dust seal 4CN-2 meets automotive HF3 standard 1CN meets automotive HF2 standard Cast aluminium head Reinforced Microglass III replacement elements Complete performance data disclosure, electrical or electronic indicators available Coreless Ecoglass III replacement elements Advantages Ability to provide reliable service under tough cyclic operating conditions Can be utilised in applications where high pressure filters may have been only option Proven reliability in cyclic applications Reduced importance of bowl torque Prevents contamination from building up on bowl/head threads Automotive industry acceptance Low profile, lightweight and durable Multi-layered design produced high capacity and efficiency Wire support reduces pleat bunching, keeps performance consistent All pertinent information is provided in an easy-tocompare format Check element condition at a glance Right style for the application No metal content in element Reduced overall weight of % Easy compaction of used elements Conversion kits available: new bowl with permanent core Benefits Reduced downtime due to premature filter failures Reduced costs, better fit for the application No downtime, no leaks Performs with real world service Easier service, eliminates thread galling Satisfies specifications without need for further testing and/or approval Less weight, smaller envelop and cleaner appearance Great performance value Reliable performance throughout element life Reduces downtime, maximises element life No hidden deficiencies Easy selection of proper filtration Optimise element life, prevent bypassing Matches your system electrical connections Environmentally friendly disposal by incineration Lower element replacement costs Lower disposal cost Retrofit coreless design to housings already installed Typical Applications Compressor lube oil Off-line filter loops Machine tools (Automotive standard) Hydrostatic drive charge pumps Mobile equipment Pilot lines for servo controls Oil patch drilling equipment Injection moulding The Parker Filtration 1/4/8CN Series Medium Pressure Filters. This partial list of applications for Parker CN Series Filters has a common factor, the need for an economical, medium pressure range filter with excellent fatigue pressure ratings. Prior to the availability of the CN filter, applications such as those listed were restricted by limitations of a spin-on can, or forced into the higher-cost range of high pressure filters. The CN Series fills this gap and is now available with environmentally friendly Ecoglass III elements. 74 Parker Hannifin Hydraulic Filter Division Europe FDHBU. Section 9

3 Specification Pressure ratings: Maximum allowable operating pressure: Rated fatigue pressure: 7 bar bar Connections: Several threaded port options available, flange faced ports available on 8CN. Connection style 1CN 4CN 8CN BSPF(G) 1, 3 / / 4, 1 1 / / 2, 2 SAE 12, 1 1, 24 24, 32 ISO 149 M27 M33 M42, M48 Metric 3-M 2 Filter housing: Head material aluminium. Bowl material hard anodized aluminium. Seal material: Nitrile or fluoroelastomer. Operating temperature range: - C to + C. Bypass valve & indicator settings: Table following gives bypass valve and corresponding indicator setting. Bypass Indicator 1.7 bar 1.2 bar 2. bar Filter element: Degree of filtration: Determined by Multipass-test according to ISO Flow fatigue characteristics: Filter media is supported so that the optimal fatigue life is achieved (ISO 3724). Microglass III (available by request) Supported with epoxy coated metal wire mesh, end cap material reinforced composite and metal inner core. Collapse rating bar (ISO 2941). Ecoglass III Supported with plastic net, end cap material reinforced composite. No metal parts. Collapse rating bar (ISO 2941). Filter element can only be used together with bowl including Eco-adaptor. Note: Ecoglass III contributes to ISO 141 quality. Indicator options: - visual M3. - electrical T1. - electronic F1(PNP). - electronic F2(NPN). For indicator details see catalogue section. Weights (kg): 1CN CN CN..9 Fluid compatibility: Suitable for use with mineral and vegetable oils, and some synthetic oils. For other fluids, please consult Parker Filtration. 1CN H I N 4CN H J N 8CN H J N F G L F G L G L F J I I M D M D M D C C C A B P A B P A B P Element removal clearance mm (2. ) 2.4 (1.) Nominal Hex E SAE - 4 Drain plug Element removal clearance mm (2. ) 2.4 (1.) Nominal Hex E SAE - 4 Drain plug Element removal clearance mm (2. ) 2.4 (1.) Nominal Hex E SAE - 4 Drain plug Dimensions in mm (inch) A B C D E F G H I J L M* N P 1CN 4CN 8CN 1. (.17) 17.8 (.73) 28.9 (11.) 2.7 (9.87) 22.4 (.33) 41. (1.81) 4. (1.83) 2. (2.44) 77.7 (3.) 2.4 (1.9) 32. (1.28) 49. (1.9) 71.1 (2.8) 7.2 (4.22) (4.91) 8.9 (3.38) 127. (.) 18.7 (.2) 73.2 (2.88) 111. (4.37) 82. (3.2) 82. (3.2) (4.8) 11.4 (.9) 38.1 (1.) 2. (2.44) 1. (4.) 22.9 (.9) 31.8 (1.2) 41.1 (1.2) 42.9 (1.9) 8.8 (2.32) 79.4 (3.12) 3. (1.44).2 (2.37) 41.3 (1.3) xM-1.x7.9 deep 4xM8-1.2x13 deep 4xM8-1.2x1 deep -27 Nm 7-8 Nm 8-9 Nm Note: add 4mm for T and F indicators 7 Medium pressure filters

4 1/4/8CN Series 8CN Flange Face Details (SAE 2 3-M) Flange face mounting holes M x 22 deep Pressure Drop Curves With 1.7 bar bypass the recommended initial pressure drop is max. bar. With bypass the recommended initial pressure drop is max 1. bar. If the medium used has a viscosity different from 3 cst, pressure drop over the filter can be estimated as follows: The total p = housing ph + (element pe x working viscosity/3). 1CN-1 Elements 1CN Empty Housing QE QE QE 4 1 QE /4 Nominal Port Size 4 1 Nominal Port Size 8 1 1CN-2 Elements QE 1.. QE QE QE Parker Hannifin Hydraulic Filter Division Europe FDHBU. Section 9

5 Pressure Drop Curves 4CN-1 Elements 4CN Empty Housing QE QE 1. QE Nominal Port Size QE. 11 / 2 Nominal Port Size CN-2 Elements QE 1. QE 1. QE. QE CN-1 Elements 8CN Empty Housing QE QE QE. QE /2 Nominal Port Size 2 Nominal Port Size CN-2 Elements QE QE. QE QE Medium pressure filters

6 1/4/8CN Series Element Service A. Stop the system s power unit. B. Relieve any system pressure in the filter line. C. Drain the filter bowl if drain port option is provided. D. Loosen and remove bowl. E. Remove element by pulling downward with a slight twisting motion and discard. F. Check bowl o-ring and anti-extrusion ring for damage and replace if necessary. G. Lubricate element o-ring with system fluid and place on post in filter head. H. Install bowl by rotating counter clockwise and tighten to specified torque. 1CN -27 Nm (1-ft. lbs) 4CN 7-8 Nm (42-ft. lbs) 8CN 8-9 Nm (-7ft. lbs) I. Confirm there are no leaks after powering the system. 3 2 CN Filters Parts List Index Description Head Indicators M3-visual auto reset: 1.2 bar M3-visual auto reset: 2. bar T1-electrical: 1.2 bar c/w DIN 43 connector T1-electrical: 2. bar c/w DIN 43 connector F1-electronic PNP with 4 LEDs: 1.2 bar F1-electronic PNP with 4 LEDs: 2. bar F2-electronic NPN with 4 LEDs: 1.2 bar F2-electronic NPN with 4 LEDs: 2. bar Bypass valve 1.7 bar assembly assembly Element (see replacement element part numbers) Bowl Single length with drain Single length with reusable core and drain Single length without drain Double length with drain Double length with reusable core and drain Double length without drain Bowl and dust seal Nitrile Drain plug: SAE-4 Nitrile Parker Hannifin Hydraulic Filter Division Europe FDHBU. Section 9

7 Ordering Information Standard products table Part numbers 1CN1QEVT1G14 1CN1QEVM3G14 1CN1QEVT1G14 1CN1QEVM3G14 1CN2QEVT1G14 1CN2QEVM3G14 1CN2QEVT1G14 1CN2QEVM3G14 4CNQEVT1G244 4CNQEVM3G244 4CN1QEVT1G244 4CN1QEVM3G244 4CN1QEVT1G244 4CN1QEVM3G244 4CNQEVT1G244 4CNQEVM3G244 4CN2QEVT1G244 4CN2QEVM3G244 4CN2QEVT1G244 4CN2QEVM3G244 8CN1QEVT1G324 8CN1QEVM3G324 8CN1QEVT1G324 8CN1QEVM3G324 8CN2QEVT1G324 8CN2QEVM3G324 8CN2QEVT1G324 8CN2QEVM3G324 Supersedes F31CN1RQETW3C2C219 F31CN1RQEM2C2C219 F31CN1RQETW3C2C219 F31CN1RQEM2C2C219 F31CN2RQETW3C2C219 F31CN2RQEM2C2C219 F31CN2RQETW3C2C219 F31CN2RQEM2C2C219 F34CN1RQETW3E2E219 F34CN1RQEM2E2E219 F34CN1RQETW3E2E219 F34CN1RQEM2E2E219 F34CN1RQETW3E2E219 F34CN1RQEM2E2E219 F34CN2RQETW3E2E219 F34CN2RQEM2E2E219 F34CN2RQETW3E2E219 F34CN2RQEM2E2E219 F34CN2RQETW3E2E219 F34CN2RQEM2E2E219 F38CN1RQETW3F2F219 F38CN1RQEM2F2F219 F38CN1RQETW3F2F219 F38CN1RQEM2F2F219 F38CN2RQETW3F2F219 F38CN2RQEM2F2F219 F38CN2RQETW3F2F219 F38CN2RQEM2F2F219 Flow (l/min) number 1CN 1CN 1CN 1CN 1CN 1CN 1CN 1CN 4CN 4CN 4CN 4CN 4CN 4CN 4CN 4CN 4CN 4CN 4CN 4CN 8CN 8CN 8CN 8CN 8CN 8CN 8CN 8CN Element length Media rating (µ) Note: Filter assemblies ordered from the product configurator on next page are on extended lead times. Where possible, please make your selection from the table above. Seals Indicator Bypass settings Ports Replacement elements 937Q 937Q 9371Q 9371Q 9374Q 9374Q 937Q 937Q 9377Q 9377Q 9378Q 9378Q 9379Q 9379Q 93711Q 93711Q 931Q 931Q 93712Q 93712Q 932Q 932Q 9371Q 9371Q 93718Q 93718Q 93719Q 93719Q 79 Medium pressure filters

8 1/4/8CN Series Ordering Information (cont.) Product Configurator Box 1 Box 2 4CN 2 Box 3 QE Box 4 V Box M3 Box Box 7 G24 Box 8 4 Box 1 Small size MP filter, T-port Medium size MP filter, T-port Large size MP filter, T-port 1CN 4CN 8CN Box 2 Length Filter type 1 2 Highlights ey (Denotes part number availability) Item is standard Item is standard green option Item is semi standard Item is non standard Note: Standard items are in stock, semi standard items are available within four weeks Box 3 Element media Ecoglass III element Degree of filtration Glass fibre 2QE Media code QE QE QE Box 4 Seal material Nitrile Seal type V B Note: When using Ecoglass III elements a bowl with reusable Eco-adaptor is required. Filter assemblies with Microglass III elements are available by request Box No indicator port indicator indicator Plugged with steel plug Electronic 4 LED, PNP, N.O. Electronic 4 LED, NPN, N.O. Electronic 4 LED, PNP, N.C. Electronic 4 LED, NPN, N.C. Box 8 Options Options Standard drain port on bowl Indicator 4 N M3 T1 P F1 F2 F3 F4 Box Bypass valve 1.7 bar Bypass valve Indicator 1.2 bar 2. bar G When filter includes a bypass valve but not an indicator, code denotes bypass setting. Box 7 Ports 1CN:Thread G 3 / 4 Thread G1 Thread SAE 12 Thread SAE 1 Thread M27, ISO149 4CN:Thread G1 1 / 4 Thread G1 1 / 2 Thread SAE 1 Thread SAE 24 Thread M33, ISO149 8CN:Thread G1 1 / 2 Thread G2 Thread SAE 24 Thread SAE 32 Thread M42, ISO149 Thread M48, ISO149 SAE flange 2" 3-M Filter connection G12 G1 S12 S1 M27 G G24 S1 S24 M33 G24 G32 S24 S32 M42 M48 R32 Ecoglass III elements ( seals) 1CN-1 1CN-2 4CN-1 4CN-2 8CN-1 8CN-2 2QE 9398Q 9372Q 937Q 937Q 93713Q 9371Q QE 9399Q 9373Q 9377Q 93711Q 93714Q 93717Q QE 937Q 9374Q 9378Q 931Q 932Q 93718Q Conversion bowl assembly (to retrofit existing CN filter housings to use coreless elements) CN-1 coreless element bowl assembly CN-2 coreless element bowl assembly 937 4CN-1 coreless element bowl assembly CN-2 coreless element bowl assembly CN-1 coreless element bowl assembly CN-2 coreless element bowl assembly QE 9371Q 937Q 9379Q 93712Q 9371Q 93719Q 1CN 4CN 8CN 1CN-1 1CN-2 4CN-1 4CN-2 8CN-1 8CN-2 Elements with nitrile seals 2Q 92893Q 92893Q 929Q 9297Q 932Q 9322Q Seal kits Nitrile S4449 S4447 S448 Q G441Q G419Q G448Q G417Q 9327Q 9323Q * S44 S4448 S449 Replacement element part numbers for conventional assemblies Q Q 92892Q 9283Q 92837Q 9328Q 9324Q Q 9337Q 9338Q 9399Q 93118Q Q Q Elements with seals 1CN-1 1CN-2 4CN-1 4CN-2 8CN-1 8CN-2 2Q 932Q 9321Q 9271Q 92717Q 9329Q 932Q Q G4189Q G419Q G4191Q G4192Q 932Q 932Q Q 93212Q 93218Q 9283Q 92838Q 8321Q 9327Q Q 9339Q 9337Q 93Q 93119Q 92993Q Q ßx(c)=2.% Average filtration beta ratio ß (ISO 1889) / particle size µm [c] ßx(c)= ßx(c)=7 ßx(c)= ßx(c)= ßx(c)= % efficiency, based on the above beta ratio (ßx) 9.% 11 Degree of filtration 98.7% % % Please note the bolded options reflect standard options with a reduced lead-time of (4) weeks or less. Consult Parker Filtration on all other lead-time options. 99.9% Metal free Ecoglass III 2QE QE QE QE Nominal flow (l/min) for filter assembly at viscosity 3cSt Housing, port size 1CN-1, G1 1CN-2, G1 4CN-1, G1 1 / 2 4CN-2, G1 1 / 2 8CN-1, G2 8CN-2, G2 2QE QE QE QE * s are available under various registered trademarks, including Viton (a registered trademark of DuPont) and Fluorel (a registered trademark of 3M) 8 Parker Hannifin Hydraulic Filter Division Europe FDHBU. Section 9