WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING

Transcription

1 Order #XXXXX - Generl Lyout Step Pln View Perspective View 0 Pge of

2 Order #XXXXX - Generl Informtion Step..00 Generl Setup Instructions - Red entire setup instruction mnul prior to unpcking prts nd pieces. A - The setup instructions re creted specificlly for this configurtion. WARNING - Setup instructions re lid out sequentilly in steps, including exploded views with detiled explntion for ssemly. Hex Tool - Essentil for Assemly Prt Identifiction - Numering Clening & Pcking DO NOT USE POWER TOOLS - For Clening Metl, Plex, & Lminte Prts: Use MILD NON-ABRASIVE clenser nd soft cloth/pper towel to clen ll surfces. - Keep exhiit components wy from het nd prolonged sun exposure. Het nd UV exposure will wrp nd fde components. Spline Connection Bse Plte & Extrusion Connection LADDERS OR LIFTS MAY BE REQUIRED - Retin ll provided Pcking Mterils. All provided pcking mterils re for ese of repcking & component protection. Disssemly ALL CONNECTIONS MUST BE TIGHTLY SECURED - For loss prevention, tighten ll setscrews nd locks during disssemly Extrusion & Lock Connection Engged Lock 0 Pge of

3 Order #XXXXX - VK-9 Bckwll Assemly Left side Step..00 A Bse Pltes 9 Verticl extrusion 9 Verticl extrusion top left outside cut 9 Verticl extrusion 9 Verticl extrusion top right outside cut Horizontl extrusion Horizontl Plcement Horizontl extrusion Top left curved extrusion Top right curved extrusion Front View Stopper ) Attch se pltes [A] to lower verticls [,]. ) Connect upper verticls [,] with connection rs []. ) Connect horizontls [,] with connection r []. ) Connect verticl [/,/] with horizontl ssemly [/]. ) Connect curved extrusions [,] with connection r []. ) Connect curved ssemly [/] etween verticls [/,/]. ) Attch Velcro Grphic to ck of frme s shown. Inside Set upper horizontl r top stopper where indicted on verticls Bck View Attch grphic to velcro on ck of ssemled frme Both s indictes loction of knos on BACKSIDE of unit. indictes loction of connection lock with kno. A Connection Br Turn Clockwise to Tighten Lock Do not over tighten s Note: Slide connection r etween extrusions nd tighten knos to secure. A 0 Pge of

4 Order #XXXXX - VK-9 Bckwll Assemly Right Side Step..00 A Bse Pltes 9 Verticl extrusion 9 Verticl extrusion top left outside cut 9 Verticl extrusion 9 Verticl extrusion top right outside cut Horizontl extrusion Horizontl Plcement Horizontl extrusion Top left curved extrusion Top right curved extrusion Front View Stopper ) Attch se pltes [A] to lower verticls [,]. ) Connect upper verticls [,] with connection rs []. ) Connect horizontls [,] with connection r []. ) Connect verticl [/,/] with horizontl ssemly [/]. ) Connect curved extrusions [,] with connection r []. ) Connect curved ssemly [/] etween verticls [/,/]. ) Attch Velcro Grphic to ck of frme s shown. Both s Set upper horizontl r top stopper where indicted on verticls Bck View Attch grphic to velcro on ck of ssemled frme Inside indictes loction of knos on BACKSIDE of unit. indictes loction of connection lock with kno. A Connection Br Turn Clockwise to Tighten Lock Do not over tighten s Note: Slide connection r etween extrusions nd tighten knos to secure. A 0 Pge of

5 Order #XXXXX - Step Horizontl Extrusion Horizontl Extrusion..00 ) Insert [,] etween left nd right side s shown. ) Attch Grphics on ck of disply. Bck/Bottom Attch grphic to velcro on ck of ssemled frme 0 Pge of

6 Order #XXXXX - VK-9 Bckwll Attchments Left Side Step..00 Heder Heder * Light Connection Attch light to ckwll where desired nd tighten in plce. * Monitor Mount Attchment * Connectors Attch monitor mount ck plte to connectors using setscrews provided. Grphic Attchment ) Attch s with to A0 s s shown in Exmple of A0 Clmp Attchment detil. ) Attch heder grphic s shown in Grphic Attchment detil. ) Connect lights s shown in Light Connection detil. ) Connect monitors s shown in Monitor Mount Attchment detil. Slide connector on ck of A0 clmp into groove of extrusion. Exmple of A0 Clmp Attchment When desired loction is found, tighten set screw to secure. Tighten kno to secure shelf/wing in plce. Stndoff Brrel Grphic Cp Slide connector on ck of stndoff rrels into groove of extrusion nd twist to secure in plce. Secure grphic to stndoffs using screw cps. 0 Pge of

7 Order #XXXXX - Pedestl QTY X Step e. e. e. e. Verticl Extrusion w/ cut Verticl Extrusion.9 Horizontl Extrusion Horizontl Extrusion 0 Horizontl Extrusion. Curved Extrusion Horizontl Extrusion 0 Horizontl Extrusion Infill Infill ) Attch lower horzontls [,,,] etween verticls [,,,] s shown. ) Attch door using pins s shown in Door Attchment detil. ) Insert infills s shown. ) Insert [9,0,,] etween verticls. ) Plce internl shelf on top of shelf supports. ) Plce counter on top. Infill Door 0 9 Counter Front Side Door Attchment Slide pin into hinge ttched to verticl. Slide door hinge top pin. Door Bck Side 0 Pge of