LED..S50L.. High-Intensity Spot Light

Transcription

1 Datasheet For use with PresencePLUS and other vision systems For the latest technical information about this product, including specifications, dimensions, and wiring, see Low-cost, washdown spot light for vision systems ontinuous or strobed operation, depending on wiring Selectable ctive High or ctive Low strobe option, depending on wiring Optically isolated strobe signal Three lens options, depending on model, to vary spot size Illuminates a large area with an even pattern of light and no shadows 12 to 30V dc operation abled and quick-disconnect models available 50 mm diameter with flat profile and 30 mm mounting base Rugged sealed housing rated to IP69K Models Model 1 LED olor Lumens / mwatts Lux / Lens ngle onnection 0.5 m 1 m LEDWS50L5-XQ White, K 295 lm lx 3445 lx LEDRS50L5-XQ Red, nm 110 lm 8000 lx 2000 lx LEDS50L5-XQ lue, nm 85 lm 4880 lx 1220 lx LEDGS50L5-XQ Green, nm 210 lm lx 3250 lx LEDIS50L5-XQ Infrared, 850 nm 760 mw ±5 (smaller, more focused spot; see graph) LEDUV395S50L5-XQ Ultraviolet, 395 nm 480 mw LEDWS50L11-XQ White, K 285 lm 5460 lx 1365 lx LEDRS50L11-XQ Red, nm 105 lm 2500 lx 625 lx LEDS50L11-XQ lue, nm 80 lm 1540 lx 385 lx LEDGS50L11-XQ Green, nm 200 lm 3900 lx 975 lx LEDUV395S50L11-XQ Ultraviolet, 395 nm 420 mw ±11 (larger spot; see graph) 5 pin Euro integral QD connector (use with 5-wire mating cordset) LEDIS50L14-XQ Infrared, 850 nm 665 mw ±14 (larger spot; see graph) LEDWS50L20-XQ White, K 270 lm 2000 lx 500 lx LEDRS50L20-XQ Red, nm 100 lm 1040 lx 260 lx LEDS50L20-XQ lue, nm 75 lm 700 lx 175 lx LEDGS50L20-XQ Green, nm 190 lm 1700 lx 425 lx ±20 (largest spot; see graph) LEDUV395S50L20-XQ Ultraviolet, 395 nm 390 mw Integral QD models only are listed. For integral 2 m (6.5'ft) PV cable, omit suffix XQ from model number (example, LEDRS50L5). model with a QD requires a mating cordset (see 5-Pin Euro-Style ordsets on page 4). P/N Rev. E 14 November

2 The following caution applies to blue LED models: UTION: Risk Group 2: Possibly hazardous optical radiation emitted from this product. Do not stare at the operating lamp. May be harmful to the eyes. Risk Group 2 (RG 2) products generally do not pose a realistic optical hazard if aversion responses limit the exposure duration or where lengthy exposures are unrealistic. - IE The following caution applies to ultraviolet models: UTION: Risk Group 2: UV Emitted from this product. Eye or skin irritation may result from exposure. Use appropriate shielding and eye protection. Risk Group 2 (RG 2) products generally do not pose a realistic optical hazard if aversion responses limit the exposure duration or where lengthy exposures are unrealistic. - IE The following caution applies to LEDIS50L5-xx infrared models: UTION: Risk Group 1: IR Emitted from this product. Use appropriate shielding or eye protection. Risk Group 1 (RG 1) products are safe for most use applications, except for very prolonged exposures where direct ocular exposures may be expected. - IE Specifications Supply Voltage and urrent Operating voltage: 12 to 30V dc Strobe voltage: 5 to 30V 15 m max. urrent draw: 400 m at 12V, 160 m at 30V Supply Protection ircuitry Protected against reverse polarity and transient voltages Light Source Three high-intensity LEDs; see models table for color temperature or wavelengths Strobe Optically isolated, 40kHz max strobe frequency 5 µs minimum on time Useful Life When operating within specifications, output will decrease less than 30% after 50,000 hours for visible and IR models; 20,000 hours for UV models. onstruction lack anodized aluminum housing; acrylic window; nickel-plated QD connector or PV-jacketed cable; black zinc-plated steel mounting nut Mounting: 30x1.5 mm thread base mount Environmental Rating IE IP67, IP69K per DIN NOTE: Do not spray the cable with a high-pressure sprayer or cable damage will result. onnections Integral 5-pin M12/Euro style QD or 2 m (6.5 ft) integral cable, depending on model; 5-pin connecting cordset required for QD models Operating onditions 20 to +50 ( 4 F to +122 F) 95% maximum relative humidity (non-condensing) Vibration and Mechanical Shock ll models meet Mil. Std. 202F requirements method 201 (vibration: 10 to 60 Hz max., double amplitude 0.06", maximum acceleration 10G). lso meets IE ; 30G 11 ms duration, half sine wave. Storage Temperature 40 to +70 ( 40 F to +158 F) ertifications tel: P/N Rev. E

3 eam Patterns Dimensions P/N Rev. E - tel:

4 Wiring Table Wire Purpose able Wire olor 2 ontinuous On Mode Strobed Mode PresencePlus Pro ontroller Terminal lock Power Wires rown (1) V dc V dc Pin 01 3 lue (3) common common Pin 02 Strobe Polarity ontrol Gray (5) open ctive Low: open ctive High: connect to common (lue wire) Open ctive Low Pin 02 ctive High Strobe Voltage Wires White (2) open 0V dc = ON (ctive Low) 0V dc = OFF (ctive High) +5 to 30V dc = OFF (ctive Low) +5 to 30V dc = ON (ctive High) Pin 04 lack (4) open Strobe common Pin Figure 1. Pinout for Mating ordset Wiring Key 1 = V dc 2 = Strobe (+) 3 = ommon 4 = Strobe common 5 = ctive high / ctive Low 5-Pin Euro-Style ordsets 5-Pin Threaded M12/Euro-Style ordsets (Single Ended) Model Length Style Dimensions Pinout (Female) MQD MQD1-506 MQD1-515 MQD1-530 MQD1-506R MQD1-515R 0.50 m (1.5 ft) 1.83 m (6 ft) 4.57 m (15 ft) 9.14 m (30 ft) 1.83 m (6 ft) 4.57 m (15 ft) Straight 44 Typ. 32 Typ. [1.26"] M12 x 1 ø = rown 2 = White 3 = lue 4 = lack 5 = Gray Right-ngle 30 Typ. [1.18"] MQD1-530R 9.14 m (30 ft) M12 x 1 ø 14.5 [0.57"] 2 For anner-supplied wire. 3 When connecting the light to a PresencePLUS Pro controller terminal block, the controller supply must be 24V dc ± 10% tel: P/N Rev. E

5 Mounting rackets ll measurements are in mm SM30 Right-angle bracket with curved slot for versatile orientation learance for M6 (¼ in) hardware Mounting hole for 30 mm sensor 12-ga. stainless steel Hole center spacing: to =40 Hole size: =ø 6.3, = 27.1 x 6.3, =ø SM30S Swivel bracket with 30 mm mounting hole for sensor lack reinforced thermoplastic polyester Stainless steel mounting and swivel locking hardware included Hole center spacing: =ø 50.8 Hole size: =ø 7.0, =ø SM30F Swivel bracket with tilt and pan movement for precise adjustment Mounting hole for 30 mm sensor 12-ga. 304 stainless steel Easy sensor mounting to extrude rail T-slot Metric and inch size bolt available SMMS30P Flat SMMS series bracket 30 mm hole for mounting sensors rticulation slots for 90 + rotation 12-ga. 300 series stainless steel Hole center spacing: =26.0, to =13.0 Hole size: =26.8 x 7.0, =ø 6.5, =ø olt thread: SM30F, = 3/8-16 x 2 in; SM30FM10, = M x 50 Hole size: = ø 30.1 SM30MM 12-ga. stainless steel bracket with curved mounting slots for versatile orientation learance for M6 (¼ in) hardware Mounting hole for 30 mm sensor Hole center spacing: = 51, to = 25.4 Hole size: = 42.6 x 7, = ø 6.4, = ø SMMS30R Right-angle SMMS series bracket 30 mm hole for mounting sensors rticulation slots for 90 + rotation 12-ga. (2.6 mm) cold-rolled steel Hole center spacing: =26.0, to =13.0 Hole size: =26.8 x 7.0, =ø 6.5, =ø anner Engineering orp Limited Warranty anner Engineering orp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. anner Engineering orp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, abuse, or the improper application or installation of the anner product. THIS LIMITED WRRNTY IS EXLUSIVE ND IN LIEU OF LL OTHER WRRNTIES WHETHER EXPRESS OR IMPLIED (INLUDING, WITHOUT LIMITTION, NY WRRNTY OF MERHNTILITY OR FITNESS FOR PRTIULR PURPOSE), ND WHETHER RISING UNDER OURSE OF PERFORMNE, OURSE OF DELING OR TRDE USGE. This Warranty is exclusive and limited to repair or, at the discretion of anner Engineering orp., replacement. IN NO EVENT SHLL NNER ENGINEERING ORP. E LILE TO UYER OR NY OTHER PERSON OR ENTITY FOR NY EXTR OSTS, EXPENSES, LOSSES, LOSS OF PROFITS, OR NY INIDENTL, ONSEQUENTIL OR P/N Rev. E - tel:

6 SPEIL DMGES RESULTING FROM NY PRODUT DEFET OR FROM THE USE OR INILITY TO USE THE PRODUT, WHETHER RISING IN ONTRT OR WRRNTY, STTUTE, TORT, STRIT LIILITY, NEGLIGENE, OR OTHERWISE. anner Engineering orp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by anner Engineering orp. - tel: