General Specifications

Transcription

1 Series M eneral Specifications Miniature Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Electrical apacity (Resistive Load) Power Level V 0V D for On-None-On & 0V D for all other circuits Logic Level (gold): 0.V V /D maximum (pplicable Range 0.m ~ 0mV ~ V) Logic/Power Level (gold over silver): ombines silver & gold ratings Note: Find additional explanation of dual rating & operating range in Supplement section. Other Ratings ontact Resistance: 0 milliohms maximum for silver; 0 milliohms maximum for gold Insulation Resistance:,000 megohms 00V D Dielectric Strength:,000V minimum between contacts for minute minimum;,00v minimum between contacts and case for minute minimum Mechanical Life: 00,000 operations minimum; 0,000 operations minimum for flat, locking & splashproof devices Electrical Life:,000 operations minimum for silver; 0,000 operations minimum for gold; 0,000 operations minimum for silver V ngle of Throw: Materials & Finishes Toggle: Brass with chrome plating Frame: Stainless steel Bushing: Brass with nickel plating Support Bracket: Brass with tin plating ase: Diallyl phthalate resin (ULV 0) Movable ontactor: Phosphor bronze with silver or gold plating Movable ontacts: Silver alloy (code W); copper with gold plating (code ); or silver alloy with gold plating (code ) Stationary ontacts: Silver with silver plating (code W); copper or brass with gold plating (code ); or silver with gold plating (code ) Terminals: opper or brass with silver plating; or copper or brass with gold plating Environmental Data Operating Temp Range: 0 through + ( F through + F) Humidity: 0 ~ % humidity for 0 (0 F) Vibration: 0 ~ Hz with peak-to-peak amplitude of.mm traversing the frequency range & returning in minute; right angled directions for hours Shock: 0 (0m/s ) acceleration (tested in right angled directions, with shocks in each direction) Sealing: Splashproof bushing options B, D, D, L, & L, which have o-rings inside & outside the bushing, meet IP of IE0 Standards. Installation Processing Mounting Torque:.0Nm (. lb in) double nut for large bushing;.nm ( lb in) double nut & 0.Nm ( lb in) single nut for all other bushings Soldering: Wave Soldering (P version) for old: See Profile in Supplement section. Manual Soldering for old: See Profile in Supplement section. Wave Soldering (P version) for Silver: See Profile B in Supplement section. Manual Soldering for Silver: See Profile B in Supplement section. Note: Lever must be in OFF (center) position while soldering. leaning: These devices are not process sealed. Hand clean locally using alcohol based solution. Standards & ertifications Flammability Standards: ULV 0 for case UL: File No. E - Recognized only when ordered with marking on switch. dd /U or /UL before dash in part number to order UL recognized switch. ll models recognized 0V or 0.V V D maximum. S: File No. 0_0_000 - ertified only when ordered with marking on switch. dd / before dash in part number to order S certified switch. ll models certified V 0V or 0.V V maximum.

2 Miniature Distinctive haracteristics Series M ntirotation design, standard on noncylindrical levers, mates toggle and bushing; bottom of toggle has two flatted sides which fit into a complementary opening inside bushing. Rockers ntijamming design protects contacts from damage due to excessive downward force on actuator. High torque bushing construction prevents rotation or separation from frame during installation. High insulating barriers increase isolation of circuits in multipole devices and provide added protection to contact points. Molded diallyl phthalate case has a UL flammability rating of V-0. Epoxy sealed terminals prevent entry of solder flux and other contaminants. Prominent external insulating barriers increase insulation resistance and dielectric strength. Interlocked actuator block, lever, and interior guide prevent switch failure due to biased lever movement. linching of frame to case well above base and terminals provides,00v dielectric strength. ctual Size Bushing Mount Bracket P Mount ngle P Mount Page Page 0 Page Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons

3 Series M ngle P Mount Miniature TYPIL SWITH ORDERIN EXMPLE Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers M0 Poles SPDT DPDT SPT PDT PDT * DPT * -pole available on vertical models only. ircuits NE OFF NE () () OFF () OFF () * * () () * () ( ) = Momentary * - circuits available with double and four pole bases only IMPORTNT: S 0 Switches are supplied without UL, culus & S marking unless specified. UL, culus & S recognized only when ordered with marking on the switch. Specific models, ratings, & ordering instructions are noted on eneral Specifications page. Small S. (0.mm) Bat S.00 (.0mm) Bat S. (.mm) Bat E.0 (.mm) Flatted E. (.mm) Flatted Toggle dimensions are based on use with a.0 (.mm) bushing; add.00 (.mm) to toggle length when combining with a.0 (.mm) bushing. L Locking Lever.0 (.mm) Dia. Locking Lever S S Standard Toggle, Bushing, & Terminal ombinations: L S0, S0, SS0, SS0, LL0, & LL0 Small Bushings.0 (.mm) Smooth with.0 (.mm) Smooth with.0 (.mm) Threaded with.0 (.mm) Threaded with Bushing For Locking Levers Smooth with for Lever Lock ontact Materials & Ratings Silver; Rated V 0V old; Rated 0.V V /D max old over Silver; V & 0.V V /D max 0 0 Terminals.0 (.mm) Right ngle P (- Pole) Right ngle PB ( Pole & 0.V Rating Only).0 (.mm) Vertical P (- Pole) (.mm) Vertical P (- Pole).0 (.mm) Smooth Bushing with.00 (.0mm) Bat Toggle B No ode DESRIPTI FOR TYPIL ORDERIN EXMPLE M0S0 Optional aps For S Bat Toggle onical ap for S Bat Toggle ap for Locking Lever Nickel Plated Supplied with Switch Black Red Blue old ontacts with 0.V Rating Vertical P Terminals with.0 (.mm) Terminal Spacing SPDT -NE- ircuit B E F ap olors Black White Red Yellow reen Blue Rockers Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons

4 Series M ngle P Mount Miniature Toggle Position ( ) = Momentary POLES & IRUITS onnected Terminals Throw & Schematics Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers Pole SP DP P P Model M0 * M0 M0 * M0 M0 The SPT model utilizes a double pole base. connection must be made during field installation. Down enter Up Down enter Up () NE OFF NE OFF OFF onn () () () M0 NE * M0 OFF M0 NE () * M0 () OFF () M0 OFF () M0 NE M0 OFF M0 NE () M0 () OFF () M0 OFF () M0 NE M0 OFF M0 NE () M0 () OFF () M0 OFF () - OPEN - SPDT - - OPEN - - DPDT ommon (in) OPEN OPEN For Throw (-On) onnected Terminals & Schematics onnection (in) PDT PDT onnection (in) The DPT model utilizes a four pole base. connection must be made during field installation. Note: Terminal numbers are not actually on the switch. * Reverse circuits available for vertical mount SP & DP upon request. onn ommon (in) 0 (OM) (OM) (OM) (OM) Pole Model Down enter Up Down enter Up SP DP M0 M0 M0 M0 M0 M0 () () () () () () onnection onnection (in) (in) 0 onnection onnection (in) (in) 0 onnection (in) 0 onnection onnection (in) (in) ommon (in) 0

5 ngle P Mount Miniature Series M SMLL TOLES Important: Toggle length changes based on bushing selected. ll illustrations are shown with.0 (.mm) long bushing. When using a.0 (.mm) long bushing, toggle length increases.00 (.mm). S. (.mm) Bat.0 (.mm) Smooth with (.).0 (.0) Dia. For, S, or S Bushing with (0.).0 (.) Dia. (0.).0 (.).0 (.) Dia.0 (.).0 When using this bushing, toggle length is increased by.00 (.mm)..0 (.mm) Threaded with (.).0 (.) Dia (.). (.0) Dia. (0.).0 /-0 Thd.0 (.).0 When using this bushing, toggle length is increased by.00 (.mm). Maximum Panel Thickness with Standard Hardware:.0 (0.mm) S E. (0.mm) Bat.00 (.) Dia.0 (0.)..0 (.mm) Flatted (.) (.).0 Standard Material & Finish: Brass with Bright hrome ontact factory for optional finishes. SMLL BUSHINS For or S Bushing with Locking Ring S S Panel utouts (.) Dia. (.) Dia.0 (.). E.0 (.mm) Smooth with (.).0 (0.).0 (.0) Dia.. (.mm) Flatted (.)..0 (.mm) Threaded with (.).0 (.0) Dia. (0.).0 S.00 (.0mm) Bat (.) Dia.00 (.).0 (.). (.) Dia.0 (.).0 /-0 Thd.0 (.).0 Maximum Panel Thickness with Standard Hardware:.0 (.mm) Standard Hardware: Hex Nuts (TH) Lockwasher (T0) Locking Ring (T0H) For dimensions, see ccessories & Hardware section. Rockers Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons

6 Series M ngle P Mount Miniature LOKIN LEVER & BUSHIN Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers LL 0 (.0) Dia. (.) Dia.0 (.) (.0).0. (.0). (.) (.0).. W Smooth with (0.).0 (.).0 (.) Dia. (.) Dia.0.0 (.mm) Right ngle P (- Pole) (.) Typ..0 on-none-on positions lock (.) Typ. (.).0.0 on-none-(on) position locks TERMINLS Single Pole Double Pole Three Pole Locking Mechanism on-off-(on) on-on-(on) positions lock TT MTERILS & RTINS on-off-on on-on-on positions lock Silver over Silver Power V 0V Terminal dimensions are shown on the Typical Switch Dimensions pages which follow. (.) Typ. (.) Typ.0 (.)..0 (on)-off-(on) (on)-on-(on) position locks old over Brass or opper Logic Level 0.V V /D maximum old over Silver No ode Note: See Supplement section to find complete explanation of operating range. Power Level or Logic Level ap for Locking Lever Supplied with ap T Material & Finish: Brass with Nickel Plating Lever Material & Finish: Brass with hrome Plating olor odes for Optional nodized luminum V or 0.V V /D maximum Note: This dual rated option is suitable when two or more identical switches are used in logic and in power circuits within the same application. See Supplement section to find complete explanation of dual rating and operating range. Black Blue Right ngle PB with Reverse ircuit ( Pole & 0.V Rating Only) Red (.) Typ. (.)..0 0

7 ngle P Mount Miniature Series M TERMINLS (ontinued) 0.0 (.mm) Vertical P (- Pole) (.) Typ.0 (.) Typ.0 (.) Typ.0 (.) Typ (.) Typ.0 0 (.) Typ (.) Typ.0 Rockers B Material: Polyethylene (.mm) Vertical P (- Pole) T for S Bat Toggle (.0) Dia. (.). TH for Inch TM for Metric Hex Nut ( per switch) Brass/Nickel (.0). /-0 Thd or M P0. (.0). (.).0 (.0)..0 Single Pole Double Pole Three Pole Four Pole.0 Single Pole Double Pole Three Pole Four Pole Terminal dimensions are shown on the Typical Switch Dimensions pages which follow. OPTIL PS & P OLORS Material: Polyethylene T onical ap for S Bat Toggle (.) Dia.0 (.) (.)..0 (.). STNDRD HRDWRE T0H for Inch T0M for Metric Locking Ring ( per switch) Steel with Zinc/hromate (.0).0 (.).0 (.). (.0) Dia. (.0) Dia. (0.).0 (.)..0 (.) Typ (.)..0 B olors vailable Black White Red.0 E F (.). (.) Typ 0 (.)..0 Yellow reen Blue T0 Lockwasher ( per switch, none with splashproof) Steel with Zinc/hromate (.) Dia. (0.) Dia.0 (0.).00 Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons

8 Series M ngle P Mount Miniature TYPIL SWITH DIMENSIS.0 (.mm) Right ngle P Single Pole Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers M0S0.0 (.mm) Right ngle P Double Pole M0S0.0 (.mm) Right ngle P Three Pole M0S0 Right ngle PB M0S (.)..00 (.)..00 (.)..00 (.)..00 (.) Dia (.).0 (.) Dia (.).0 (.) Dia (.).0 (.). (.). Single Pole Reverse ircuit (.) Dia (.0). (.) (.0).0.0 (.0).0.0 (.).0 (.)..0 (.). (.) Dia (.).0.0 (.). (.) (.) Typ (.).0 (.) Typ (.) Typ.0 (.). (0.).0 (.) (.0). (.0). (.0). (.0). (.). (.)..0 (.) Typ. (.)..0 (.) Typ. (.). (.)..0 (.) Typ. (.). (.) Typ.

9 ngle P Mount Miniature TYPIL SWITH DIMENSIS Single Pole Series M.0 (.mm) Vertical P (.) Dia Rockers (.) Dia (.) Dia (.) Dia (.) Dia (.).0 (.) Dia (.).0 (.) Dia (.).0 (.) Dia (.).0 (.). (.). (.0). (.0)..0 (.).0.0 (.) (.).0 (.)..0.0 (.).0 (.)..0 (.) Typ.0 Double Pole.0 (.) Typ.0 Three Pole.0 (.) Typ.0 Four Pole.0 (.) Typ.0 (.) (.) (.) 0 (.). (.) (.0). (.) Typ (.0). (.) Typ (.) Typ (.). (.) Typ (.). (.0). (.) (.) M0S0.0 (.mm) Vertical P M0S0.0 (.mm) Vertical P M0S0.0 (.mm) Vertical P (.0). (.) Typ M0S0 Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons

10 Series M ngle P Mount Miniature TYPIL SWITH DIMENSIS (.mm) Vertical P Single Pole Supplement ccessories Indicators Touch Tilt Tactiles Slides Rotaries Keylocks Programmable Illuminated PB Pushbuttons Rockers M0S (.mm) Vertical P Double Pole M0S (.mm) Vertical P Three Pole M0S (.mm) Vertical P Four Pole M0S (.) Dia (.) Dia (.) Dia (.) Dia (.) Dia (.).0 (.) Dia (.).0 (.) Dia (.).0 (.) Dia (.).0 (.). (.). (.0). (.0)..0 (.).0.0 (.) (.).0 (.)..0.0 (.).0 (.) (.) (.) (.) 0 (.). (.) (.0). (.) Typ (.0). (.) Typ (.) Typ (.). (.) Typ (.). (.0). (.) (.) (.0). (.) Typ