For the latest technical information about this product, including specifications, dimensions, and wiring, see

Transcription

1 VALU-BEAM 92 Series AC- and DC-powered sensors with solid-state outputs For the latest technical information about this product, including specifications, dimensions, and wiring, see Features Choose models for to 3V dc or 24 to 25V ac operation DC models have bipolar solid-state outputs: one NPN (sinking) and one PNP (sourcing) AC models have an SPST solid-state output rated for up to 3/4 amp with simple 2- wire hookup All models have a rear panel sensitivity adjustment and light/dark operate switch DC models include Banner s Alignment Indicating Device (AID ) system Choose models with integral cable or Mini-style QD (quick-disconnect) connector; 9 m (3') cables are also available Emitter (E) and Receiver (R) Models OPPOSED Infrared, 88 nm Models Range Cable* Supply Voltage Output Type SMA9E SMA9EQD 3-pin Mini QD -25V ac/dc - SM9R SM9RQD 6 m (2') 4-pin Mini QD -3V dc Bipolar NPN/PNP SM2A9R SM2A9RQD 3-pin Mini QD 24-25V ac SPST SCR Solid-state 2-wire SMA9ESR SMA9ESRQD 3-pin Mini QD -25V ac/dc - SM9RSR SM9RSRQD 3 m (') 4-pin Mini QD -3V dc Bipolar NPN/PNP SM2A9RSR SM2A9RSRQD 3-pin Mini QD 24-25V ac SPST SCR Solid-state 2-wire * 9 m cables are available by adding suffix W/3 to the model number of any cabled sensor (e.g., SMA9E W/3). A model with a QD connector requires a mating cable; see Quick-Disconnect Cables on page. WARNING: Not To Be Used for Personnel Protection Never use this product as a sensing device for personnel protection. Doing so could lead to serious injury or death. This product does NOT include the self-checking redundant circuitry necessary to allow its use in personnel safety applications. A sensor failure or malfunction can cause either an energized or de-energized sensor output condition. P/N 3467_web 4//22

2 Retroreflective Mode Models VALU-BEAM 92 Series Visible Red, 65 nm RETRO Non-Polarized P POLAR RETRO Polarized Models Range Cable* Supply Voltage Output Type Non-Polarized SM92LV -3V dc SM92LVQD.5 to 9 m (6" to 3') SM2A92LV 24-25V ac SM2A92LVQD Polarized SM92LVAG SM92LVAGQD SM2A92LVAG SM2A92LVAGQD.3 to 4.5 m (' to 5') Bipolar NPN/PNP SPST SCR Solid-state 2-Wire -3V dc Bipolar NPN/PNP 24-25V ac SPST SCR Solid-state 2-Wire Retroreflective range is specified using one model BRT-3 retroreflector (3" diameter). Actual sensing range may be more or less than specified, depending upon the efficiency and reflective area of the retroreflector used. Use polarized models when shiny objects will be sensed. Diffuse Mode Models DIFFUSE Infrared, 88 nm Models Range Cable* Supply Voltage Output Type SM92D SM92DQD SM2A92D SM2A92DQD 76 mm (3") -3V dc Bipolar NPN/PNP 24-25V ac SPST SCR Solid-state 2-Wire SM92DSR SM92DSRQD SM2A92DSR SM2A92DSRQD 38 mm (5") -3V dc Bipolar NPN/PNP 24-25V ac SPST SCR Solid-state 2-Wire tel: P/N 3467_web

3 VALU-BEAM 92 Series Convergent Mode Models CONVERGENT VISIBLE RED CONVERGENT Visible Red or Infrared; see below Models Range Cable* Supply Voltage Output Type Visible Red 65 nm SM92CV SM92CVQD SM2A92CV SM2A92CVQD 38 mm (.5") Spot Size at Focus:.5 mm (.6") -3V dc Bipolar NPN/PNP 24-25V ac SPST SCR Solid-state 2-Wire Infrared 88 nm SM92C SM92CQD SM2A92C SM2A92CQD 38 mm (.5") -3V dc Bipolar NPN/PNP 24-25V ac SPST SCR Solid-state 2-Wire Glass Fiber Optic Individual Emitter or Receiver Models GLASS FIBER TWO SENSORS Infrared, 88 nm Use where the separation between emitting and receiving fibers is more than a few feet, or where it is inconvenient to run both fibers from a single sensor. Watertight o-ring-sealed sensor/fiber interface. Models Range Cable* Supply Voltage Output Type SMA9EF SMA9EFQD -25V ac/dc SM9RF SM9RFQD Range varies with fiber used -3V dc Bipolar NPN/PNP SM2A9RF SM2A9RFQD 24-25V ac SPST SCR Solid-state 2-Wire * 9 m (3') cables are available by adding suffix W/3 to the model number of any cabled sensor (e.g., SMA9EF W/3). A model with a QD connector requires a mating cable; see Quick-Disconnect Cables on page. P/N 3467_web - tel:

4 Glass Fiber Optic Models VALU-BEAM 92 Series GLASS FIBER Infrared 88 nm Watertight o-ring-sealed sensor/fiber interface. Models Range Cable* Supply Voltage Output Type SM92F SM92FQD SM2A92F SM2A92FQD Range varies with sensing mode and fiber optics used -3V dc Bipolar NPN/PNP 24-25V ac SPST SCR Solid-state 2-Wire * 9 m (3') cables are available by adding suffix W/3 to the model number of any cabled sensor (e.g., SM92F W/3). A model with a QD connector requires a mating cable; see Quick-Disconnect Cables on page. Dimensions 5.8 mm (2.") 36.6 mm (.4) Cabled Models QD Models Rear View LED Indicator 35.6 mm (.) 39. mm (.5) Lens Centerline Light/Dark Operate Select (L.O. = CW, D.O. = CCW) Sensitivity Control (Turn CW to Increase) 4.5 mm (#) Screw Clearance (2) NOTE: Control potentiometers are behind cover screws; remove screws to access controls 7.8 mm (.7") 2.7 mm (.5") M3 x.5 External Thread /2" - 4 NPSM Internal Thread Hex Nut Supplied 26.7 mm (.5") Mini-style Quick-disconnect M3 x.5 Thread Hex Nut Supplied 25.4 mm (.") 5.6 mm (.22") Convergent Sensing Mode (model suffix LVAG, C and CV) 39.6 mm (.56") Glass Fiber Optic (model suffix F, EF and RF) 42.2 mm (.66") Fiber Port Centerline tel: P/N 3467_web

5 VALU-BEAM 92 Series Specifications - DC Models Supply Voltage and Current to 3V dc at 2 ma maximum, exclusive of load; except for SMA9E, ESR and EF emitters, which operate from to 25V ac or dc Supply Protection Circuitry Protected against reverse polarity and transient voltages Output Configuration Bipolar: One current sourcing (PNP) and one current sinking (NPN) open-collector transistor Output Rating 25 ma continuous, each output Off-state leakage current: less than microamps Output saturation voltage: (PNP output) less than volt at ma and less than 2 volts at 25 ma Output saturation voltage: (NPN output) less than 2 millivolts at ma and less than volt at 25 ma Output Response Time Receivers only: 8 milliseconds ON and 4 milliseconds OFF, independent of signal strength. All other models: 4 milliseconds ON/OFF NOTE: millisecond delay on power-up; outputs do not conduct during this delay. Repeatability Opposed and Glass Fiber Optic Emitter-Receiver pairs:. millisecond Retro, Diffuse, Convergent and Glass Fiber Optic Models:.3 milliseconds Adjustments Light/Dark Operate select switch and Sensitivity control potentiometer, both located at rear of sensor Indicators Alignment Indicating Device (AID ) lights a top-mounted red LED indicator whenever the sensor sees a light condition; its pulse rate is proportional to the light signal strength (the stronger the signal, the faster the pulse rate). Model SMA9E and SM9ESR emitters: visible-red tracer beam indicates Power ON and enables lineof-sight alignment. Construction Reinforced thermoplastic polyester housing, totally encapsulated, molded acrylic lenses and stainless steel hardware Environmental Rating Meets NEMA standards, 2, 3, 3S, 4, 4X, 2 and 3 IEC IP66 Connections PVC-jacketed or 9 m (3') cables or 4-pin Mini-style quick-disconnect (QD) fitting available. NOTE: Opposed-mode emitters use 3-pin Mini-style QD fitting. See Quick-Disconnect Cables on page. Operating Conditions Temperature: -2 to 7 C (-4 to 58 F) Maximum relative humidity: 9% at 5 C (non-condensing) Certifications DC Hookups Emitters - Cabled Emitters - QD (3-Pin Mini-Style) 3-Pin Mini-Style Pinout (Cable Connector Shown) -25V ac/dc bk -25V ac/dc = Black = Brown 3 = Blue P/N 3467_web - tel:

6 Other DC Models - Cabled Other DC Models - QD (4-Pin Mini- Style) VALU-BEAM 92 Series 4-Pin Mini-Style Pinout (Cable Connector Shown) wh bk Load Load -3V dc wh bk Load Load -3V dc = Brown 2 = White 3 = Blue 4 = Black Specifications - AC Models Supply Voltage and Current 24 to 25V ac (5/6 Hz); except for SMA9E, ESR and EF emitters, which operate from to 25V ac or dc Supply Protection Circuitry Protected against transient voltages Output Configuration SPST SCR solid-state relay with either normally closed or normally open contact (light/dark operate selectable); 2-wire hookup Output Rating Minimum load current ma, max. steady-state load capability 75 ma to 5 C ambient (22 F), 5 ma to 7 C ambient (58 F) Inrush capability: 4 amps for second (non-repetitive) Off-state leakage: current less than.7 ma rms On-state voltage drop: 5 volts rms at 75 ma load, volts rms at 5 ma load Output Protection Circuitry Protected against false pulse on power-up Output Response Time Receivers only: 8 milliseconds ON and 4 milliseconds OFF, independent of signal strength. All other models: 4 milliseconds ON/OFF OFF time does not include load response of up to /2 ac cycle (8.3 milliseconds). Response time specification of the load should be considered when total response time is important. NOTE: millisecond delay on power-up; outputs do not conduct during this delay. Repeatability Opposed and Glass Fiber Optic Emitter-Receiver pairs:. millisecond Retro, Diffuse, Convergent and Glass Fiber Optic Models: 2.6 milliseconds Adjustments Light/Dark Operate select switch and Sensitivity control potentiometer, both located at rear of sensor Indicators Top-mounted red LED indicator lights when output is conducting. Model SMA9E and SM9ESR emitters: visible-red tracer beam indicates Power ON and enables lineof-sight alignment. Construction Reinforced thermoplastic polyester housing, totally encapsulated, molded acrylic lenses and stainless steel hardware Environmental Rating Meets NEMA standards, 2, 3, 3S, 4, 4X, 2 and 3 IEC IP66 Connections PVC-jacketed or 9 m (3') cables or 3-pin Mini-style (QD) fitting available. See Quick-Disconnect Cables on page. Operating Conditions Temperature: -2 to 7 C (-4 to 58 F) Maximum relative humidity: 9% at 5 C (non-condensing) Application Notes.) 92 Series ac sensors can be destroyed from overload conditions. 2.) Use on low voltage requires careful analysis of the load to determine if the leakage current or on-state voltage of the sensor will interfere with proper operation of the load. 3.) The false-pulse protection feature may cause momentary drop-out of the load when the sensor is wired in series or parallel with mechanical switch contacts. Certifications tel: P/N 3467_web

7 VALU-BEAM 92 Series AC Hookups Emitters - Cabled Emitters - QD (3-Pin Mini-Style) 3-Pin Mini-Style Pinout (Cable Connector Shown) -25V ac/dc bk -25V ac/dc 3 2 Other AC Models - Cabled 24-25V ac Load Other AC Models - QD (3-Pin Mini-Style) 24-25V ac Load bk = Black 2 = Brown 3 = Blue Excess Gain Mode Emitter and Receiver Models. m.33' SMA9E / SM9R, SMA9E / SM2A9R. m 3.3' m 33' m 33' SMA9ESR / SM9RSR, SMA9ESR / SM2A9RSR. m.33'. m.33'. m 3.3' m 33' Retroreflective Mode Models With BRT-3 Reflector SM92LV, SM2A92LV Retroreflective Mode With BRT-3 Reflector SM92LVAG, SM2A92LVAG Retroreflective Mode. m.33'. m.33'. m 3.3' m 33'. m.33'. m.33'. m 3.3' m 33' P/N 3467_web - tel:

8 VALU-BEAM 92 Series Mode SM92D, SM2A92D SM92DSR, SM2A92DSR Diffuse Mode Diffuse Mode Diffuse Mode Models mm. mm. mm mm mm. mm. mm mm Visible Red 65 nm Infrared 88 nm SM92CV, SM2A92CV SM92C, SM2A92C Convergent Mode Convergent Mode Models Convergent Mode mm. mm. mm mm mm. mm. mm mm Glass Fiber Optic Individual Emitter or Receiver Models SMA9EF & SM9RF, SMA9EF & SM2A9RF IT23S Fibers W/L6F Lenses. m.33' IT23S Fibers W/L9 Lenses. m 3.3' m 33' m 33' SM92F SM2A92F SM92F SM2A92F Diffuse Mode Glass Fiber Optic Models IT3S Fibers IT23S Fibers BT23S Fiber BT3S Fiber mm. mm. mm mm mm. mm. mm mm tel: P/N 3467_web

9 VALU-BEAM 92 Series Beam Patterns Mode 5 mm mm SMA9E / SM9R, SMA9E / SM2A9R 6" 3 mm 2 mm SMA9ESR / SM9RSR, SMA9ESR / SM2A9RSR 2" 8" 5 mm 2" mm Emitter and Receiver Models 5 mm mm 2" mm 2 mm 8" 5 mm 6" 3 mm 2" 5 m 5' 3 m ' 45 m 5' 6 m 2' 75 m 25'.6 m 2'.2 m 4'.8 m 6' 2.4 m 8' 3. m ' Non-Polarized Polarized 5 mm mm SM92LV, SM2A92LV Retroreflective Mode 6." 4." 75 mm 5 mm SM92LVAG, SM2A92LVAG Retroreflective Mode 3." 2." 5 mm 2." 25 mm." Retroreflective Mode Models 5 mm mm With BRT-3 Reflector 2." 4." 25 mm 5 mm With BRT-3 Reflector." 2." 5 mm 6." 75 mm 3." 2 m 6.6' 4 m 3' 6 m 2' 8 m 26' m 33' m 3.3' 2 m 6.6' 3 m ' 4 m 3' 5 m 6' 8 mm 2 mm SM92D, SM2A92D Diffuse Mode.75".5" 8 mm 2 mm SM92DSR, SM2A92DSR Diffuse Mode.75".5" 6 mm.25" 6 mm.25" Diffuse Mode Models 6 mm 2 mm.25".5" 6 mm 2 mm.25".5" 8 mm.75" 8 mm.75" 5 mm 6" 3 mm 2" 45 mm 8" 6 mm 2 75 mm 3" 75 mm 3" 5 mm 6" 225 mm 9" 3 mm 2" 375 mm 5" Visible Red 65 nm Infrared 88 nm 2.4 mm.6 mm SM92CV, SM2A92CV Convergent Mode.9".6" 2.4 mm.6 mm SM92C, SM2A92C Convergent Mode.9".6" Convergent Mode Models.8 mm.8 mm.3".3".8 mm.8 mm.3".3".6 mm.6".6 mm.6" 2.4 mm.9" 2.4 mm.9" 2.5 mm.5" 25 mm." 37.5 mm.5" 5 mm 2." 62.5 mm 2.5" 5 mm.6" 3 mm.2" 45 mm.8" 6 mm mm 3." 3 mm 2 mm SMA9EF & SM9RF, SMA9EF & SM2A9RF 2" 8" Glass Fiber Optic Individual Emitter or Receiver Models mm mm 2 mm IT23S Fibers With L9 lenses IT23S Fibers With L6F lenses 8" 3 mm 2" 2.4 m 8' 4.8 m 6' 7.2 m 24' 9.6 m 32' 2 m 4' P/N 3467_web - tel:

10 VALU-BEAM 92 Series Mode 75 mm 5 mm 25 mm SM92F/SM2A92F 3" 2" ".9 mm.3 mm.7 mm SM92F/SM2A92F Diffuse Mode.8".5".3" Glass Fiber Optic Models 25 mm 5 mm IT3S IT23S " 2".7 mm.3 mm BT3S BT23S.3".5" 75 mm 3".9 mm.8" mm 2 mm 8" 3 mm 2" 4 mm 6" 5 mm 2" 7.5 mm.3" 5 mm.6" 22.5 mm.9" 3 mm.2" 37.5 mm.5" Accessories Quick-Disconnect Cables Model Length Style Dimensions Pinout (Female View) MBCC-36 3-Pin Mini-style MBCC-32 4 m (2') straight MBCC-33 9 m (3') 6 mm max. (2.) 7/8-6UN-2B 3 = Black 2 = Brown 2 3 = Blue MBCC-46 4-Pin Mini-style MBCC-42 4 m (2') straight MBCC-43 9 m (3') ø 28 mm max. (.") 2 4 = Brown 3 2 = White 3 = Blue 4 = Black Cabling Accessories Model Description AC-6 armored cable jacket I.D. 5/6"; O.D. 7/6" PVC-6 flexible PVC tubing (not for QD models) I.D. /; O.D. 3/8" RF-2NPS Compression fitting for attaching armored cable or PVC tubing HF-2NPS Flexible black nylon cable protector Includes a neoprene gland that compresses around the VALU-BEAM cable to provide an additional seal against moisture Resistant to gasoline, alcohol, oil, grease, solvents and weak acids Working temperature range of -3 to C (-22 to 22 F) - tel: P/N 3467_web

11 VALU-BEAM 92 Series Extension Cables (without connectors) The following cables are available for extending the length of existing sensor cable. These are 3 m (') lengths of VALU-BEAM cable. This cable may be spliced to existing cable. Connectors, if used, must be customer-supplied. Model Type Used With: EC32-4-conductor SM92 Series dc sensors EC32A- 2-conductor For all emitters and SM2A92 Series ac sensors Retroreflective Targets Banner offers a wide selection of high-quality retroreflective targets. See the Accessories section of your current Banner Photoelectric Sensors catalog for complete information. NOTE: Polarized sensors require corner cube type retroreflective targets. Non-polarized sensors may use any retroreflective target. Replacement Lens Assemblies VALU-BEAM lens assemblies are field-replaceable. In addition, some lenses may be used to convert from one sensing mode to another, or to change the sensing range of a particular sensor. The possible conversions are listed in the table below. Models Description Possible Sensing Mode or Range Changes UC-9AG Replacement lens for LVAG Change LV to LVAG UC-9C Replacement lens for C and CV Change LV to CV UC-9DSR Replacement lens for DSR, ESR, and RSR Change D or F to DSR, EF to ESR, and RF to RSR UC-9F Replacement lens for F Change D to F and DSR to F UC-9FP Replacement lens for FP UC-9L Replacement lens for E, R, LV, and D Change LVAG to LV, CV to LV, DSR to D, and F to D UC-9J Attach to E, R, ESR, RSR, LV, and D models Flat polycarbonate dust cover P/N 3467_web - tel:

12 VALU-BEAM 92 Series Mounting Brackets SMB3C 3 mm split clamp, black PBT bracket Stainless steel mounting hardware included Mounting hole for 3 mm sensor Hole center spacing: A=ø 45 Hole size: B=ø A B SMB3SC Swivel bracket with 3 mm mounting hole for sensor Black reinforced thermoplastic polyester Stainless steel mounting and swivel locking hardware included Hole center spacing: A=ø 5.8 Hole size: A=ø 7., B=ø A B SMB3MM 2-ga. stainless steel bracket with curved mounting slots for versatile orientation Clearance for M6 (¼") hardware Mounting hole for 3 mm sensor 57 7 A B C 57 Hole center spacing: A = 5, A to B = 25.4 Hole size: A = 42.6 x 7, B = ø 6.4, C = ø 3. Banner Engineering Corp Limited Warranty Banner Engineering Corp. warrants its products to be free from defects in material and workmanship for one year following the date of shipment. Banner Engineering Corp. will repair or replace, free of charge, any product of its manufacture which, at the time it is returned to the factory, is found to have been defective during the warranty period. This warranty does not cover damage or liability for misuse, ase, or the improper application or installation of the Banner product. THIS LIMITED WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES WHETHER EXPRESS OR IMPLIED (IN- CLUDING, WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE), AND WHETHER ARISING UNDER COURSE OF PERFORMANCE, COURSE OF DEALING OR TRADE USAGE. This Warranty is exclusive and limited to repair or, at the discretion of Banner Engineering Corp., replacement. IN NO EVENT SHALL BANNER ENGINEERING CORP. BE LIABLE TO BUYER OR ANY OTHER PERSON OR ENTITY FOR ANY EXTRA COSTS, EXPEN- SES, LOSSES, LOSS OF PROFITS, OR ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES RESULTING FROM ANY PRODUCT DEFECT OR FROM THE USE OR INABILITY TO USE THE PRODUCT, WHETHER ARISING IN CONTRACT OR WAR- RANTY, STATUTE, TORT, STRICT LIABILITY, NEGLIGENCE, OR OTHERWISE. Banner Engineering Corp. reserves the right to change, modify or improve the design of the product without assuming any obligations or liabilities relating to any product previously manufactured by Banner Engineering Corp.