In-Sight Hardware specifications

Transcription

1 specifications In-Sight 5000, 5100, 5400, 5400S, 5400C, 5401, and Linz/Austria Pummererstr. 36 Tel.: +43-(0) * Memory Job/Program 16MB non-volatile flash memory; Unlimited storage via remote network device Image processing 64MB Image Sensor , 5400, 5400S & 5400C /4-inch CCD 1/3-inch CCD 1/3-inch CCD 1/1.8-inch CCD (4.60mm x 3.97mm; (5.84mm x 4.94mm; (5.80mm x 4.92mm; (8.50mm x 6.80mm; Optical Properties 4.5mm diagonal) 6mm diagonal) 6mm diagonal) 8.923mm diagonal) 640 x 480 pixel display 640 x 480 pixel display 1024 x 768 pixel display 1600 x 1200 pixel display (307,200 sq. pixels, (307,200 sq. pixels, (786,432 sq. pixels, (1,920,000 sq. pixels, 5.6 x 5.6µm pixel size) 7.4 x 7.4µm pixel size) 4.65 x 4.65µm pixel size) 4.4 x 4.4µm pixel size) Electronic shutter speed 32µs to 1000ms 16µs to 1000ms 32µs to 1000ms 27µs to 1000ms Color 5000, 5100, 5400, 5400S, 5401 & C No Yes Rapid reset, progressive scan, full-frame integration 256 gray levels (8 bits/sec) Gain/Offset controlled by software Acquisition Rate , 5400, 5400S & 5400C Up to 30 frames Up to 60 frames Up to 19 frames Up to 15 frames per second per second per second per second (exposure dependent) (exposure dependent) (exposure dependent) (exposure dependent) Lens type C-mount I/O Trigger 1 opto-isolated, acquisition trigger input Remote software commands via Ethernet and RS232 Trigger voltage ON 20 to 28V (24V nominal) OFF 0 to 3V (12V nominal threshold) ON to 1.3mA Trigger current OFF <150µA Resistance ~22,000 Ohms Trigger delay 250µSec latency between leading edge of trigger and start of delay acquisition. Input pulse should be minimum of 1ms wide. Discrete inputs 8 inputs available, using optional Model 1450 I/O Expansion inputs Module. Discrete outputs 2 built-in, high-speed outputs 8 additional outputs available, using optional Model 1450 I/O Expansion Module. Notes: 1) Maximum acquisition rate is based on 1ms exposure, and a full image frame capture 1

2 In-Sight 5000, 5100, 5400, 5400S, 5400C, 5401, and 5403 I/O (cont.) High-speed output voltage 28V maximum through external load 200mA maximum sink current High-speed OFF state leakage current 200µA maximum output current External load resistance 120 to 10K Ohms Each line rated at a maximum 200mA, protected against over-current, short circuit, and transients from switching inductive loads. High current inductive loads require external protection diode. Status LEDs Power, Network Status, Network Traffic, 2 user configurable Communications Network 1 Ethernet port, 10/100 BaseT, TCP/IP protocol. Supports DHCP (factory default) or static IP address Serial 1 RS-232C port (1200 to 115,200 baud rates and 2400 baud is not supported by the Model 1450 I/O Expansion Module.) Power Power 5000, 5100, 5400, 5400S, 5400C & consumption 24VDC ± 10%, 350mA 24VDC ± 10%, 500mA Mechanical Material & finish Mounting Dimensions Weight Environmental Operating temperature Operating humidity Storage temperature Storage humidity Protection (With lens enclosure installed) Shock Vibration Certifications Approvals All models except 5400S: Die-cast aluminum housing, painted 5400S: ASTM 316L stainless steel electropolished-passivated Eight M4 threaded mounting holes (four front and four back) All models except 5400S: 84mm (3.34in) x 124.7mm (4.91in) x 61.6mm (2.43in) with lens cover installed 41mm (1.62in) x 124.7mm (4.91in) x 61.6mm (2.43in) without lens cover installed 5400S: 91.44mm (3.60in) x mm (4.89 in) x 61.47mm (2.42in) with lens cover installed All models except 5400S: 297.6g (1oz) lens cover installed, w/o lens 5400S: g (2 lb.08oz) lens cover installed, w/o lens 0 C to 45 C (32 F to 113 F) 95%, non-condensing -30 C to 80 C (-22 F to 176 F) 95%, non-condensing 5400S model is NEMA 6P/IP68 rated; all other models are NEMA 6/IP67 rated 80 Gs (800 M/S 2 at 11 ms) per IEC EA 10 Gs (10-to 500 Hz at 100 M/S 2 / 15mm for two hours in each axis) per IEC FC CE, CUL, FCC 2

3 In-Sight 5000, 5100, 5400, 5400S, 5400C, 5401, and 5403 In-Sight 5000 In-Sight 5100, 5400, and 5400s In-Sight 5401 In-Sight 540OC B G R In-Sight

4 In-Sight 5000, 5100, 5400, 5400C, 5401, and 5403 Lens Cover Thread Protector The lens cover included with In-Sight 5000 Series vision sensors provides wash-down and dust protection. A thread protector, also included, protects the threads when the lens cover is not used. 4

5 In-Sight 5400s (4.89) (2.42) (3.60) 23 (2) (4.30) 4xM (.31) (8) 54 (1.97) (3.86) 27 (1) 5

6 In-Sight 5110, 5410, and 5411 In-Sight Hardware specifications ID Tools 1D Codes Code 3 of 9; Code 128; Interleaved 2 of 5; Reduced Space Symbology (RSS); UPC/EAN; PostNet; Planet Code; Pharma Code; UPU-57 2D Codes Data Matrix; QR Code; PDF417; Composite Symbology (CS) Quality Assessment Metrics 1D Codes ISO D Codes Data Matrix ISO 16022, AS9132, Cognex Supplemental Metrics QR Code ISO 18004, Cognex Supplemental Metrics Firmware In-Sight version 2.52 and later Memory Job/Program 16MB non-volatile flash memory; Unlimited storage via remote network device Image processing 64MB Image Sensor In-Sight 5110 and 5410 In-Sight /3-inch CCD (5.84mm x 4.94mm; 1/3-inch CCD (5.80mm x 4.92mm; 6mm diagonal) 640 x 480 pixel 6mm diagonal) 1024 x 768 pixel display (307,200 sq. pixels, display (786,432 sq. pixels, 7.4 x 7.4µm pixel size) 7.65 x 7.65µm pixel size) Electronic shutter speed: 32µs to 1000ms Acquisition Rapid reset, progressive scan, full-frame integration 256 gray levels (8 bits/sec) Gain/Offset controlled by software In-Sight 5110 and 5410 In-Sight 5411 Up to 60 full frames per second Up to 20 full frames per second (exposure dependent) (exposure dependent) Lens type C-mount I/O Trigger 1 opto-isolated, acquisition trigger input Remote software commands via Ethernet and RS232 Trigger voltage ON 20 to 28V (24V nominal); OFF 0 to 3V (12V nominal threshold) Trigger current ON to 1.3mA; OFF <150µA Resistance ~22,000 Ohms Trigger delay 250µSec latency between leading edge of trigger and start of acquisition. Input pulse should be minimum of 1ms wide. Discrete inputs 8 inputs available, using optional Model 1450 I/O Expansion Module. Discrete outputs 2 built-in, high-speed outputs 8 additional outputs available, using optional Model 1450 I/O Expansion Module. I/O (cont.) High-speed output voltage High-speed output current Status LEDs Lighting Lighting methods Communications Network Serial Power Power consumption Mechanical Material and finish Mounting Dimensions Weight Environmental Operating temperature Operating humidity Storage temperature Storage humidity Protection Shock Vibration Certifications Approvals 28V maximum through external load 200mA maximum sink current OFF state leakage current 200µA maximum External load resistance 120 to 10K Ohms Each line rated at a maximum 200mA, protected against overcurrent, short circuit, and transients from switching inductive loads. High current inductive loads require external protection diode. Power, Network Status, Network Traffic, 2 user configurable May be used with Cognex external light modules, or with the integrated light ring included in optional Image Formation System (IFS) kits. Kits include ring light, lens, and protective lens cover. 1 Ethernet port, 10/100 BaseT, TCP/IP protocol. Supports Ethernet/IP and ModBus/TCP. Supports DHCP (factory default) or static IP address 1 RS-232C port (1200 to 115,200 baud rates and 2400 baud is not supported by the Model 1450 I/O Expansion Module.) 24VDC ± 10%, 350mA Die-cast aluminum housing, painted Eight M4 threaded mounting holes (four front and four back) 84mm (3.34in) x 124.7mm (4.91in) x 61.6mm (2.43in) with lens cover installed 41mm (1.62in) x 124.7mm (4.91in) x 61.6mm (2.43in) without lens cover installed g (1oz) lens cover installed, w/o lens 0 C to 45 C (32 F to 113 F) 0 to 95%, non-condensing -30 C to 80 C (-22 F to 176 F) 0 to 95%, non-condensing IP67 (NEMA Type 6) with lens cover installed 80 Gs (800 M/S 2 at 11 ms) per IEC EA 10 Gs (10-to 500 Hz at 100 M/S 2 / 15mm for two hours in each axis) per IEC FC CE, CUL, FCC in-sight 5110 and 5410 in-sight 5411 dimensional drawings are shown on page 4 6

7 METAL LENS COVER (optional for ALL in-sight 5000 SERIES vision sensors except the 5400s) LNS-CVR-R-00 (Red) LNS-CVR-UV-00 (UV) A FILTER 47.6 (1.87) 52.2 (2.06) 47 (1.85) Effective Clearance 52mm x 5 Thread FILTER EXTENSION 55mm x 1.5-6g Thread Mill Notes: A Any standard 52mm x.75 mm filter can be used with the extension. The maximum distance from the top of the In-Sight 5XXX C-mount to the inside surface of the filter glass is typically 41.5mm (1.63). metal extension ring (optional for ALL in-sight 5000 SERIES vision sensors except the 5400s) M55x1.5 LNS-CVR-EXT-01 Ø58.0 (2.28) Ø50 (2.00) M55x1.5 Note: Material: Black anodized aluminum 33.5 (1.32) diffuse ring light (DRL) (optional for in-sight 5110, 5410, and 5411 ID Readers) Etched TOP M2 Screws IFS-DRL-050 Ring Light Board Conductor Standoffs Connectors In-Sight Camera 7

8 image formation system (ifs) kit (optional for In-Sight 5110, 5410, and 5411 ID Readers) Seven kits are available, each with a different lens Image Formation System (IFS) Kits Kit Part Number Lens Attributes Working Distance Field of View (mm) (mm) IFS-RRL IFS-RRL IFS-RRL IFS-RRL IFS-RRL IFS-RRL IFS-RRL (Provided with In-Sight 5110 ID Reader) 8