Hilti MI industrial pipe support system Technical documentation

Transcription

1 Hilti MI industrial pipe support system Technical documentation page 1

2 page 2

3 Technical data /mean values including torsion Technical data s = s = 4 MI-90 MI-0 Material thickness s [mm] Cross-sectional area A [mm 2 ] Weight of girder [kg /m] Material Elastic limit (yield strength) f y,k [N/mm 2 ] Permissible tensile stress* σ Zul [N/mm 2 ] Modulus of elasticity [N/mm 2 ] Shear modulus [N/mm 2 ] Surface Hot-dip galvanized 70 µm Cross-section values y-axis Axis of gravity ey [mm] Moment of inertia ly [cm 4 ] Section modulus Wy [cm 3 ] Radius of gyration iy [cm] Cross-section values x-axis Axis of gravity ez [mm] Moment of inertia lz [cm 4 ] Section modulus Wz [cm 3 ] Radius of gyration iz [cm] Torsion data Torsional moment of inertia Σ lt [cm 4 ] Torsional section modulus Wt =2*ABredt * [cm 3 ] * The permissible stress is calculated from σd / γg/q with γ = 1,4. σd results from higher yield strength due to cold forming in accordance with DAST-RILI016, issued 1992: σd = fyk / γm mit γm = 1,1 page 3

4 Single-span subject to bending in one axis F 1 when f=l/200, F 2 when f=l/300, F when σ zul including the framing section s own weight MI-90, one single load MI-0, one single load F 50 F 50 L/2 L/2 L L/2 L/2 L s = s = 4 Length of F [kn] f [mm] F1 [kn] f [mm] F2 [kn] f [mm] span [mm] σ zul L/200 L/ < Length of F [kn] f [mm] F1 [kn] f [mm] F2 [kn] f [mm] span [mm] σ zul L/200 L/ < Selection of framing section for single span with max. load when f < L/200 Single central load incl. framing section s own weight L F[kN] Load F (kn) MI-90 MI-0 MQ-21 D/F* MQ-41 D/F* MQ-41/F* MQ D/F* Length of span (mm) * Technical data for the MQ System can be found in the Installations Systems main catalogue. page 4

5 MI connector on MI girder (recommended loads 1) ) MIC-90-U or MIC-0-U on MI-90 ±Fy rec. [kn] ± Fx rec. [kn] ± Fz rec. [kn] Fy // Fx // Fz* Fy + Fx + Fz * Force permissible in only one direction (// = or) Note: Not to be used for cantilevers. Section always requires support at both ends. MIC-90-U or MIC-0-U on MI-0 MI-90 or MI-0 Each with single screw (84 Nm) Fy MI-90 ±Fy rec. [kn] ± Fx rec. [kn] ± Fz rec. [kn] Fy // Fx // Fz* Fy + Fx + Fz * Force permissible in only one direction (// = or) Note: Not to be used for cantilevers. Section always requires support at both ends. Fx Fz MIC-90-L auf MI-90 oder MI-0 Single screw (84 Nm) ±Fy rec. [kn] ± Fx rec. [kn] ± Fz rec. [kn] Fy // Fx // Fz* 13,20 8,26 18,60 Fy + Fx + Fz 13,20 3,10 18,60 * Force permissible in only one direction (// = or) Note: Designed for use with cantilevers. May be supported at only one end. 2) 2 screws crosswise (84Nm) Fx Fy Single screw (84 Nm) Fz MI beam clamps (recommended loads 1) ) M x 85 MI-GC-M Fz ±Fy rec. [kn] ± Fx rec. [kn] ± Fz rec. [kn] Fy // Fz Fy + Fx + Fz All loads apply to 1 beam clamp. Recommended shear loads apply to galvanized steel on galvanized steel. Clamps must always be used in pairs. Tightening torque M D :69 Nm Fy 30 M Fx 1) Calculation of rated values: F d = F rec. 1,5 2) Our technical advisory service would be pleased to assist with design and calculation. page 5

6 MI connector on steel beams (recommended loads 1) ) 140 beam clamps (69 Nm) 60 x 13 MIC-S-90-AA ±Fy rec. [kn] ± Fx rec. [kn] ± Fz rec. [kn] Fy // Fx // Fz* Fy + Fx + Fz * Force permissible in only one direction (// = or) Note: Not to be used for cantilevers. Always requires support at both ends. MI-90 Fx Fy 100 B 300 MIC-S-90-A Fz 2 x screws crosswise (84 Nm) ±Fy rec. [kn] ± Fx rec. [kn] ± Fz rec. [kn] Fy // Fx // Fz* ,00 Fy + Fx + Fz ,11 * Force permissible in only one direction (// = or) Note: Designed for use with cantilevers. May be supported at only one end. 2) 4 x beam clamps (69 Nm) MIC-S-90-B Fy 140 ±Fy rec. [kn] ± Fx rec. [kn] ± Fz rec. [kn] Fy // Fx // Fz* Fy + Fx + Fz * Force permissible in only one direction (// = or) Note: Designed for use with cantilevers. May be supported at only one end. 2) MIC-S-90-C MI-90 Fx x 13 Fz x screws crosswise (84 Nm) ±Fy rec. [kn] ± Fx rec. [kn] ± Fz rec. [kn] Fy // Fx // Fz* Fy + Fx + Fz * Force permissible in only one direction (// = or) Note: Designed for use with cantilevers. May be supported at only one end. 2) MIC-S-0-A 4 x beam clamps (69 Nm) ±Fy rec. [kn] ± Fx rec. [kn] ± Fz rec. [kn] Fy // Fx // Fz* Fy + Fx + Fz * Force permissible in only one direction (// = or) Note: Designed for use with cantilevers. May be supported at only one end. 2) MIC-S-0-B MI-0 Fy 140 ±Fy rec. [kn] ± Fx rec. [kn] ± Fz rec. [kn] Fy // Fx // Fz* Fy + Fx + Fz * Force permissible in only one direction (// = or) Note: Designed for use with cantilevers. May be supported at only one end. 2) MIC-S-0-C Fx x 13 Fz x screws crosswise (84 Nm) ±Fy rec. [kn] ± Fx rec. [kn] ± Fz rec. [kn] Fy // Fx // Fz* Fy + Fx + Fz * Force permissible in only one direction (// = or) Note: Designed for use with cantilevers. May be supported at only one end. 2) 1) Calculation of rated values: F d = F rec. 1,5 2) Our technical advisory service would be pleased to assist with design and calculation. page 6

7 MI connector on concrete (recommended loads 1) ) screws crosswise (84 Nm) 100 MIC-C90-AA 3) ±Fy rec. [kn] ± Fx rec. [kn] ± Fz rec. [kn] Fy // Fx // Fz* Fy + Fx + Fz *Force permissible in only one direction (// = or) Note: Designed for use with cantilevers. May be supported at only one end. 2) MI-90 Fx Fy 140 Fz 200 MIC-C90-D 4) screws crosswise (84 Nm) ±Fy rec. [kn] ± Fx rec. [kn] ± Fz rec. [kn] Fy // Fx // Fz* Fy + Fx + Fz *Force permissible in only one direction (// = or) Note: Designed for use with cantilevers. May be supported at only one end. 2) Fx MI-90 Fy x 17 MIC-C0-D 4) Fz ±Fy rec. [kn] ± Fx rec. [kn] ± Fz rec. [kn] Fy // Fx // Fz* Fy + Fx + Fz *Force permissible in only one direction (// = or) Note: Designed for use with cantilevers. May be supported at only one end. 2) Fy screws crosswise (84 Nm) Fx 47 x 17 Fz MIC-C90-U 3) ±Fy rec. [kn] ± Fx rec. [kn] ± Fz rec. [kn] Fy // Fz* Fy + Fz *Force permissible in only one direction (// = or) Note: Not to be used for cantilevers. Always requires support at both ends. MI-90 Fy 100 Single screw (84 Nm) ) Calculation of rated values: F d = F rec. x 1,5 2) Our technical advisory service would be pleased to assist with design and calculation. 3) Fx rec. : Given values apply only to use of HST/HST-R M anchors; higher values possible when other anchors are selected. Fy rec. : Given values apply to all M anchors Note: When loading with Fy, the elongated hole in the base plate in line with the direction of force must be filled with high-strength mortar (e.g. HIT-HY 150). 4) Fx rec.,fy rec.,fz rec. : Given values apply only to use of HST/HST-R M16 anchors; higher values possible when other anchors are selected. Fx Fz page 7

8 MI girder extension (recommended loads 1) ) 4 screws crosswise in end of each girder (84 Nm) MIC-90-E Fy 250 The loading capacity of the extension depends on the moments acting in the Y- and Z-axes. Please consult our technical advisory service. Fx Fz MI-90 MIC-0-E The loading capacity of the extension depends on the moments acting in the Y- and Z-axes. Please consult our technical advisory service. Fy 4 screws crosswise in end of each girder (84 Nm) 250 MI-0 Fx Fz MI connector / pedestal connector (recommended loads 1) ) MIC-T Fy 2 screws (84 Nm) ±Fy rec. [kn] ± Fx rec. [kn] ± Fz rec. [kn] Fz* Fy + Fx + Fz * Force permissible in only one direction (// = or) Note: Always to be fitted on both sides. Fx 1) Calculation of rated values: F d = F rec. x 1,5 Fz page 8

9 MI Multi-angle connectors ( recommended loads 1) ) MIC-U-MA (connection to MI girder ) 8 0 Tension or compression F rec. [kn] 2) Angle Note: Always to be fitted in pairs ,5 2 screws (84 Nm) MIC-SA-MA (connection to steel beam) Tension or compression F rec. [kn] 2) Angle beam clamps (69 Nm) D C B MIC-SB-MA (connection to steel beam) Tension or compression F rec. [kn] 2) Angle x MIC-SC-MA (connection to steel beam) Tension or compression F rec. [kn] 2) Winkel MIC-CU-MA (connection to concrete) Tension or compression F rec. [kn] 2)3) Angle ) Calculation of rated values: F d = F rec. 1,5 2) F rec. always acts in the longitudinal axis of the girder, irrespective of angle. 3) F rec. : Given values apply only to use of HST/HST-R M anchors; higher values possible when other anchors are selected x page 9

10 page 10

11 MI girder Torsionally rigid girder. Pipes may be mounted on all four sides simultaneously. Scale marks facilitate installation /cutting to length. Crimped-in depression for 100% compatibility with MQ channel system. Technical data Material: S235JRG2 as per DIN Galvanizing: Hot-dip galvanized 75 µm Section height Length Material thickness Weight Ordering designation Item no. Packaged [mm] (m) [mm] (kg/m) in lengths of ➀MI-90 3m m ➀MI-90 6m m ➁MI-0 3m m ➁MI-0 6m m s = s = 4 page 11

12 MI connectors: Crossbeam connectors Fine adjustment in 5 mm increments for maximum flexibility. Only two connecting screws required. Keyed hold for optimum transmission of forces and moments. Self-locking nuts for vibration-resistant screw connections. Technical data Material: S235 JRG2 as per DIN EN Galvanizing: Hot-dip galvanized 55µm Note Always to be supported at opposite end. Crossbeam connectors with connecting parts For girder type Weight per Ordering designation Item no. Package set [kg] MI MIC-90-U MI MIC-0-U MI Items Set besteht in set aus: Crossbeam connectors without connecting parts For girder type Weight per Ordering designation Item no. Package set [kg] MI MIC- 90-U-AP MI MIC-0-U-AP MI page

13 MI connectors: Cantilever connectors Fine adjustment in 5 mm increments for maximum flexibility. Only four connecting screws required. Keyed hold for optimum transmission of forces and moments. Self-locking nuts for vibration-resistant screw connections Technical data Material: S235 JRG2 as per DIN EN Galvanizing: Hot-dip galvanized 55 µm Note Designed for cantilever applications. May be supported at only one end. Cantilever connector with connecting parts For girder type Weight per Ordering designation Item no. Package set [kg] MI MIC-90-L ➀ Items Set besteht in set aus: 4x Cantilever connector without connecting parts For girder type Weight per Ordering designation Item no. Package set [kg] MI MIC-90-L-AP page 13

14 MI connectors: Pedestal connector Fine adjustment in 5 mm increments for maximum flexibility. Keyed hold for optimum transmission of forces and moments. Technical data Material: S235 JRG2 as per DIN EN Galvanizing: Hot-dip galvanized 55 µm Pedestal connector with connecting parts 8 0 For girder type Weight per Ordering designation Item no. Package set [kg] MI-90/MI MIC-T Items Set besteht in set aus: page 14

15 MI connectors: Girder extension Flexurally rigid extension/connection for MI girder. Built-in stop prevents the extension sliding right inside the girder. Technical data Material: S235 JRG2 as per DIN EN Galvanizing: Hot-dip galvanized 55 µm Girder extension with connecting parts For girder type Weight per ordering designation Item no. Package set [kg] MI MIC-90-E MI MIC-0-E Items Set besteht in set aus : 250 8x 8x MI-90 Items Set besteht in set aus : 4x 4x 250 MI-0 8x page 15

16 MI steel connectors: Connection to steel beams For connection to standard steel beams without drilling or welding. Suitable for connection to flange or web. For use with MI-GC-M beam clamp. B Technical data Material: S235 JRG2 as per DIN EN Galvanizing: Hot-dip galvanized 55 µm Steel connectors with connecting parts For girder type Steel beam width B C D Weight per Ordering designation Item no. Package [mm] [mm] [mm] set [kg] MI MIC-S90-AA MI MIC-S90-A MI MIC-S90-B MI MIC-S90-C MI MIC-S0-A MI MIC-S0-B MI MIC-S0-C x 13 D C B D C B B 300 MI-0 MI MI x x Note: Always to be supported at opposite end. Note: + Designed for cantilever applications. May be supported at only one end. Items Set besteht in set aus: page 16

17 MI steel connectors: Connection to steel beams For connection to standard steel beams without drilling or welding. Suitable for connection to flange or web. Lightweight for easy one man installation. B Technical data Material: S235 JRG2 as per DIN EN Galvanizing: Hot-dip galvanized 75 µm Steel connectors welded bracket Fz 1/2 1/2 For girder type Length L Steel beam width B C D Weight per Ordering designation Item no. [mm] [mm] [mm] [mm] set [kg] Recommended working load F z [kn] MI MIC-S90-A MI MIC-S90-A MI MIC-S90-A MI MIC-S90-A MI MIC-S90-A MI MIC-S90-B MI MIC-S90-B MI MIC-S90-B MI MIC-S90-B MI MIC-S90-B MI MIC-S90-C MI MIC-S90-C MI MIC-S90-C MI MIC-S90-C MI MIC-S90-C MI MIC-S0-A MI MIC-S0-A MI MIC-S0-A MI MIC-S0-A MI MIC-S0-A MI MIC-S0-B MI MIC-S0-B MI MIC-S0-B MI MIC-S0-B MI MIC-S0-B MI MIC-S0-C MI MIC-S0-C MI MIC-S0-C MI MIC-S0-C MI MIC-S0-C Fz 1/3 1/3 Fz 1/3 Note: + Designed for cantilever applications. May be supported at only one end. Calculated by: Suitable Hilti beam clamps MI-GC-M, Item No F Z L D C B F Z L D C B x x page 17

18 MI concrete connectors: Connection to concrete Four elongated holes for easy wall mounting. Designed for ceiling, wall and floor mounting. Technical data Material: S235 JRG2 as per DIN EN Galvanizing: Hot-dip galvanized 55 µm Concrete connector with connecting parts For girder type Weight per Ordering designation Item no Package set [kg] MI MIC-C90-AA MI MIC-C90-D MI MIC-C0-D MI MI x x 17 Note: Always to be supported at opposite end. Note: + Designed for cantilever applications. May be supported at only one end. Items Set besteht in set aus: page 18

19 MI concrete connectors: Connection to concrete Four elongated holes for easy wall mounting. Designed for ceiling, wall and floor mounting. Lightweight for easy one man installation. Technical data Material: S235 JRG2 as per DIN EN Galvanizing: Hot-dip galvanized 75 µm Concrete connector welded bracket 1/2 Fz 1/2 Fz 1/3 1/3 Fz 1/3 For girder type Length L Weight per Ordering designation Item no. [mm] set [kg] Recommended working load F z [kn] MI MIC-C90-D MI MIC-C90-D MI MIC-C90-D MI MIC-C90-D MI MIC-C90-D MI MIC-C0-D MI MIC-C0-D MI MIC-C0-D MI MIC-C0-D MI MIC-C0-D F Z F Z L L x x 17 Note: + Designed for cantilever applications. May be supported at only one end. Anchor Calculated by: Approved Hilti HST(R) M16 anchors; alternative approved Hilti anchors are the Hilt HVZ, HIT-TZ(R) of the same nominal diameter and same version. page 19

20 MI concrete connectors: Connection to concrete walls Lighter version for structures supported at both ends. Elongated holes for easier positioning. Simple support for installation between two walls. Technical data Material: S235 JRG2 as per DIN EN Galvanizing: Hot-dip galvanized 55 µm Note Always to be supported at opposite end. Concrete wall connector with connecting parts For girder type Weight per Ordering designation Item no. Package set [kg] MI MIC-C90-U MI Items Set besteht in set aus: 1x 25 x 14 1x page 20

21 MI connectors: Multi-angle connectors For supports / corner struts at angles between 0 and 180. For connecting directly to standard steel beams or concrete. Technical data Material: S235 JRG2 as per DIN EN Galvanizing: Hot-dip galvanized 55 µm MI angle connectors for girder, with connecting parts For girder type Weight per Ordering designation Item no. Package set [kg] MI-90/MI MIC-U-MA Items Set besteht in setaus: ,5 80 MI angle connectors for steel, with connecting parts For girder type Steel beam width B C D Weight per Ordering designation Item no. Package [mm] [mm] [mm] set [kg] MI-90/MI MIC-SA-MA MI-90/MI MIC-SB-MA MI-90/MI MIC-SC-MA Items Set besteht in setaus: 80 D C B x MI angle connectors for concrete, with connecting parts For girder type Weight per Ordering designation Item no. Package set [kg] MI-90/MI MIC-CU-MA Items Set besteht in setaus: x 14 page 21

22 MI steel / concrete connectors Base plates for steel / concrete All steel beam widths from mm covered by only 3 plate sizes. Technical data Material: S235 JRG2 as per DIN EN Galvanizing: Hot-dip galvanized 55 µm MI base plates for steel / concrete, without connecting parts For girder type Steel beam width B C D Weight per Ordering Item no. Package [mm] [mm] [mm] set [kg] designation MI-90/MI MIB-SA MI-90/MI MIB-SB MI-90/MI MIB-SC MI-90/MI-0 For connection to concrete 5.88 MIB-CD D C B x x 17 page 22

23 Flexy pack: Adaptable connector for steel or concrete The girder connection point can be positioned as desired for special cases. Supplied in a primer finish for trouble-free welding. Can be galvanized later if desired. Technical data Material: S235 JRG2 as per DIN EN Corrosion protection: None (primer coating-basic connector) Pos. 1 Flexy pack connector for welding as desired, without connecting parts Pos. 2 Parts list Ordering designation Item no. Info Position MIC-SC90 or MIC-SC or Pos.1 MIB-SA or MIB-SB / Depending on base material Pos.2 MIB-SC or MIB-CD / or size of steel beam MI basic connector for welding, without connecting parts For girder type Weight per Ordering designation Item no. Package set [kg] MI MIC-SC MI MIC-SC page 23

24 Pipe clamps: U-bolt clamps for uninsulated pipes Reliable fastening system for U-bolts. Elongated holes for full adjustment of pipe position. Keyed hold for optimum transmission of forces. Technical data for the clamping system Material: S235 JRG2 as per DIN EN Galvanizing: Hot-dip galvanized 55 µm Connecting screws: M (connection to MI-girder) MI U-bolt clamps with connecting parts For girder type Weight per Ordering designation Item no. Package set [kg] MI MIC-UB * MI MIC-UB90 L MI MIC-UB * MI MIC-UB90-M * MI MIC-UB0-M * *numbers of pairs in set 28, x x x ,5 x x x 13, x x 13, x 13, x 13, Items Set in set : besteht aus: Items Set in : set besteht aus: 1x page 24

25 Pipe clamps: MI U-bolts for uninsulated pipes Small contact surface between U-bolt and pipe. Minimizes crevice corrosion. In compliance with DIN standard for U-bolts. h b2 d1 Technical data for the clamping system Material: S235 JRG2 as per DIN EN Galvanizing: Hot-dip galvanized 45 µm Temperatures: 300 C e d3 U-bolts with connecting parts Nominal size Pipe outside d1 b2 h Shank d3 e Weight Ordering designation Item no. Package diameter Da dia. each NW [mm] [mm] [mm] [mm] [mm] [mm] [kg] M MI-UB 25-M M MI-UB 40-M M MI-UB 50-M M MI-UB 65-M M MI-UB 80-M M MI-UB 100-M M MI-UB 5-M M MI-UB 150-M M MI-UB 200-M M MI-UB 250-M page 25

26 MI pipe clamps: Pipe supports for insulated pipes With mounting holes for installing light-duty fixed points. F x F y H s Fz D a B F F y s F x H L 1 Fz D a F B F y F x s H L 1 Fz D a F B W L W L + F z + F z W + F z 13 L 1 ring / 1 rib for DN25-DN150 2 rings / 1 rib for DN25-DN300 Heavy-duty version for DN200-DN Technical data for the clamping system Material: S235 JRG2 as per DIN EN Galvanizing: Hot-dip galvanized 70 µm Temperatures: Up to 300 C Low-friction plate 8 Sliding support clamps Fixed point Nominal Pipe outside B s F W H L L1 Clamping Weight per Permissible loads Ordering designation Item no. Package size diameter Da screw set Fx +Fz Fz Fy NW [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [kg] (kn) (kn) (kn) (kn) M MI-PS1/ M MI-PS1/ M MI-PS1/ M MI-PS1/ M MI-PS1/ M MI-PS1/ M MI-PS1/ M MI-PS1/ M MI-PS1/ M MI-PS1/ M MI-PS1/ M MI-PS1/ M MI-PS1/ M MI-PS1/ M MI-PS1/ M MI-PS1/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ * The maximum permissible loads for connecting components must be taken into account when the pipe support is used! page 26

27 MI pipe clamps: Pipe supports for insulated pipes With mounting holes for installing light-duty fixed points. F x F y H s Fz D a B F F y s F x H L 1 Fz D a F B F y F x s H L 1 Fz D a F B W L W L + F z + F z W + F z 13 L 1 ring / 1 rib for DN25-DN150 2 rings / 1 rib for DN25-DN300 Heavy-duty version for DN200-DN Technical data for the clamping system Material: S235 JRG2 as per DIN EN Galvanizing: Hot-dip galvanized 70 µm Temperatures: Up to 300 C Low-friction plate 8 Sliding support clamps Fixed point Nominal Pipe outside B s F W H L L1 Clamping Weight per Permissible loads Ordering designation Item no. Package size diameter Da screw set Fx +Fz Fz Fy NW [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [kg] (kn) (kn) (kn) (kn) M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ M MI-PS2/ * The maximum permissible loads for connecting components must be taken into account when the pipe support is used! page 27

28 MI pipe clamps: MI sliding support clamping system for insulated pipes Pipe ring support free to move in one direction. Fully adjustable. Spacer plates permit use of pipe supports with base plates of greater thickness. Technical data for the clamping system Material: S235 JRG2 as per DIN EN Galvanizing: Hot-dip galvanized 45 µm Technical data for low-friction system Material: PE-UH MW Friction value: µ = 0,15 Temperature resistance: 273,15 C to +90 C MI clamping system for sliding support, with connecting parts For girder type Weight per Ordering designation Item no. Package set [kg] MI MIC-PS * MI MIC-PS * MI-90/MI MIC-PSP-4MM * MI-90/MI MIC-PSP-6MM * *Number of pairs in package M M MI low-friction system for sliding support 75 For girder type Weight per Ordering designation Item no. Package set [kg] MI-90/MI MIC-PG page 28

29 MI pipe clamps: MI rigid support clamping system, with connecting parts Quickly and easily installed pipe support system for light-duty fixed points. Technical data for the clamping system Material: S235 JRG2 as per DIN EN Galvanizing: Hot-dip galvanized 45 µm MI clamping system for fixed points, with connecting parts 102 M 102 M For girder type Weight per Ordering designation Item no. Package set [kg] MI MIA-B090-M * MI MIA-B00-M * *Number of pairs in package page 29

30 MI pipe clamps: Adaptor plate for pipe support clamping system, incl. connecting parts The adaptor plate takes the place of the steel beam flange and thus permits the use of conventional clamping systems for pipe supports. Technical data for the clamping system Material: S235 JRG2 as per DIN EN Galvanizing: Hot-dip galvanized 55 µm 210 M 10 Adaptor plate with connecting parts For girder type Weight per Ordering designation Item no. Package set [kg] MI MIC-PA MI MIC-PA M MI pipe clamps: Twin roller support Dimensions suitable for fastening to MI-girder with MIC-PA90 or MIC-PA0. Technical data: Body material: S235 JRG2 as per DIN EN Roller material: S355 JO as per DIN EN Axle material: Stainless steel (1.4541) Rated load capacity: 15 kn Coefficient of friction: For girder type Weight per Suitable pipe Ordering designation Item no. Package set [kg] diameter [mm] MI-90/MI MI-DPR DA Items Set besteht in setaus: E 8 DA = Outside-diameter pipe E = x DA page 30

31 MI pipe clamps: Plate for weld-on tabs Easy installation of standard weld-on tabs, e.g. for spring hangers. Technical data for the clamping system Material: S235 JRG2 as per DIN EN Galvanizing: U-bolt galvanized 45µm, plate with primer finish For girder type Weight per Ordering designation Item no. Package set [kg] MI MIC-SPH MI MIC-SPH M 130 M 90 0 page 31

32 MI accessories: Individual connecting parts Parts designed for easy assembly with one hand (shaped to prevent rotation). Easy hand plate (5) for easy single-handed adjustment of the connection. Technical data Material: EN-GJMW as per DIN EN 1562 Screws: 8.8 grade Nuts: 8 grade DIN 1661, self locking Galvanizing: 45 µm For girder type Weight per Ordering designation Item no. Packege set [kg] MI-90 0,16 MIA-EH MI-0 0,19 MIA-EH MI-90 0,10 MIA-OH MI-0 0,13 MIA-OH MI-90, MI-0 0,28 MIA-EH-P MI-90, MI-0 0,02 M-F hex.collar nut MI-90, MI-0 0,06 MIA-TP MI-90, MI-0 0,10 Hex.head screw M0-F/ MI-90, MI-0 0,11 Hex.head screw M130-F/ MI-90, MI-0 0,005 A 13-F washer ,6 36,6 M 0 36,6 36,6 M 150 Examples of applications (cantilever) Assembly procedure M x M M ,2 x,2 7 36,6 36,6 page 32

33 MI accessories: End caps Ends of girder closed securely. With built-in opening to permit drainage of liquids. Technical data Material: Temperature resistance: Moplen EP 240H 30 to +90 C For girder type Weight Ordering designation Item no. Package [kg] MI MIA-EC MI MIC-EC page 33

34 MI accessories: Beam clamps for various flange thicknesses For steel beams with a flange thickness of 3 - mm and angle of up to 15. Spacers for use with flange thicknesses greater than mm. Technical data Material: EN-GJMW as per DIN EN 1562 Galvanizing: Hot-dip galvanized 55 µm Screws: 8.8 grade Note The flat nose must be positioned against the steel beam and the round nose on the connecting part or spacer. For girder type Weight per Ordering designation Item no. Package set [kg] MI-90/MI MI-GC-M MI-90/MI MI-GCD-6MM MI-90/MI MI-GCD-MM M x M page 34

35 page 35

36 MI / MQ connector Direct connection to components of the Hilti MQ system. Keyed hold for optimum transmission of forces and moments. Technical data Material: S235 JRG2 as per DIN EN Galvanizing: Hot-dip galvanized 55 µm MI / MQ connectors with connecting parts For channel Weight per Ordering designation Item no. Package set [kg] MQ-41, MQ-21D 0.36 MIC-MI/MQ-X all MQ single channels 0.05 MIC-MI/MQ-M Items Set besteht in setaus: 250 4x 61 x 11 Items Set besteht in setaus: Assembly procedure M8x16 M8x16 SW13 5 Description Size Ordering designation Item no. Package Magnetic wrench SW 13 MQZ-SVS SW 13 with mit Magneteinsatz magnetic insert 200 mm page 36

37 MQV-UB U-bolt pipe clamp for MQ system Easy installation of U-bolts. Fastened with wing nuts or hex. nuts. Technical data Material: S235JR as per DIN EN Galvanizing: hot-dip galvanized, approx. 55 µm For channel Weight per Ordering designation Item no. Package set [g] MQ-41-F, MQ-41D-F, MQ-52-72D-F 70 MQV-UB-M * * Number of pairs in package MQV-PS pipe support for MQ system Easy installation as guide-type pipe support. Fastened with wing nuts or hex. nuts. Technical data Material: S235JR as per DIN EN Galvanizing: hot-dip galvanized, approx. 55 µm 55 For channel Weight each Ordering designation Item no. Package [g] MQ-41-F, MQ-41D-F, MQ-52-72D-F 70 MQV-PS * * Number of pairs in package 94 MQP-U universal joint For D1 D2 Weight each Ordering Item no. Package [mm] [mm] [g] designation M,5,5 390 MQP-U M M16 16,5 16,5 390 MQP-U M Item no. Max. recommended load Tightening torque M D [kn] [Nm] MQP-U M MQP-U M MQP-45 -F base material connector For channel Weight each Ordering designation Item no. Package [g] MQ-21-F, MQ-41-F 350 MQP-45 -F page 37

38 Example of application Opposite cantilever arms at same or similar height Pos. 3 Pos. 5 Pos. 1 Pos. 2 Pos. 4 Parts list Quantity Ordering designation Item no. Info Position 2 MIC-90-L-AP Cantilever connectors Pos. 1 2 MIC-EH Pos. 2 2 MIA-TP Pos. 3 4 MIA-OH Pos. 4 6 M-F hex. collar nut Self-locking nuts Pos. 5 Example of application Girder connection to steel beam Girder can be connected to steel beam without welding. Parts list (beam height up to 320 mm) Quantity Ordering designation Item no. Info Position 1 MIC-S*(A/B/C) 3048/304813/ To suit beam size Pos. 1 1 MIB-S* / / Size as (1) Pos. 2 4 AM -F M-F threaded rod Pos. 3 8 M-F hex. collar nut Self-locking nuts Pos. 4 *Plate size to be selected to suit width between flanges Pos. 4 Pos. 1 Pos. 3 Pos. 2 Beam height up to about 320 mm. page 38

39 Parts list (beam height greater than 320 mm) Quantity Ordering designation Item no. Info Position 2 MI Length to suit beam size Pos.1 8 MIC-UB90-M Pos.2 4 Hex.head screw M0F/ Pos.3 M-F hex. collar nut Self-locking nuts Pos.4 4 AM -F M-F threaded rod Pos.5 Pos. 2 Pos. 1 Pos. 5 Pos. 4 Pos. 3 Beam height greater than 320 mm. Further connections using MIC-90-L cantilever connector. Example of application Cross connection between MI girder Keyed hold for optimum transmission of forces and moments. Parts list Quantity Ordering designation Item no. Info Position 1 MIB-SA Pos. 1 4 MIA-EH-P Pos. 2 4 A13-F Pos. 3 4 M130F/8.8 hex screw Pos. 4 4 M hex. collar nut Self-locking nut Pos. 5 Pos. 1 Pos. 4 Pos. 5 Pos. 3 Pos. 2 Pos. 5 page 39

40 Hilti = registered trademark of Hilti Corp., Schaan W en 1 Printed in Liechtenstein 2006 Right of technical and programme changes reserved S. E. & O. Hilti. Outperform. Outlast. Hilti Corporation 9494 Schaan Liechtenstein P F